Interface:
|
Name of
the interface running the E-LMI protocol.
|
Ether LMI
Link Status:
|
Status of
the E-LMI protocol on the interface. Possible values are Up, Down, or Unknown
(PVT disabled).
|
UNI Id:
|
Name of
the UNI as configured by the ethernet uni
id command. This output field does not appear if the UNI ID is
not configured.
|
Line
Protocol State:
|
Status of
the interface line protocol. Possible values are Up, Down, or Admin-Down.
|
MTU (x PDUs reqd for full
report)
|
Maximum
Transmission Unit of the interface and the number (x) of E-LMI PDUs of
that size required to send one full status report.
|
CE-VLAN/EVC Map Type:
type (x EVCs)
|
Map type,
which describes how CE VLAN IDs are mapped to specific EVCs. Possible valued
for
type are Bundling, All to One Bundling, or Service
Multiplexing with no bundling. The number
x of EVCs in the map are displayed in parentheses.
|
Configuration: Status counter
|
Value of
the MEF N393 Status Counter as configured by the
status-counter command.
|
Polling
Verification Timer
|
Value of
the MEF T392 Polling Verification Timer (in seconds) as configured by the
polling-verification-timer command. Displays
"disabled" if the PVT is turned off.
|
Last Data
Instance Sent:
|
Current
value of the Data Instance.
|
Last
Sequence Numbers: Sent
x, Received
y
|
Values of
the last sent (x) and received (y) sequence numbers
as reported in sent PDUs.
|
Reliability Errors:
(Status
Enq Timeouts, Invalid Report Type, and Invalid Sequence Number)
|
Number of
times the specified types of reliability errors have occurred since the
protocol was enabled on the interface or counters were cleared.
|
Protocol
Errors:
(Malformed
PDUs, Invalid Message Type, Duplicated IE, and others)
|
Number of
times the specified types of protocol errors have occurred since the protocol
was enabled on the interface or counters were cleared.
|
Full
Status Enq Rcvd, PDU Rcvd, LMI Link Status Changed, Counters cleared, Full
Status Sent, PDU Sent, and Last Protocol Error.
|
Elapsed
time (hrs:mins:secs ago) since the specified events last occurred or counters
were cleared. Displays "never" if the event has not occurred since the protocol
was enabled on the interface or counters were cleared.
|
Subinterface:
|
Name of
the subinterface corresponding to the EVC.
|
VLANs:
|
VLAN
traffic on the interface that corresponds to the EFPs encapsulation, with the
following possible values:
-
Numbers of the matching VLAN IDs
Note
|
If
Q-in-Q encapsulation is configured, only the outer tag is displayed.
|
-
default—Indicates that Default tagging is configured, or the
encapsulation specifies to match "any."
-
none—No matches for the configured encapsulation have occurred
on the interface.
-
untagged/priority—Traffic is either untagged or has priority
tagging.
Note
|
If the
message "EVC omitted from Full Status due to encapsulation conflict" is
displayed above the VLAN output, a misconfiguration has occurred with two or
more EFPs having a conflicting encapsulation.
|
|
EVC
Status:
|
State of
the EVC, with the following possible values:
-
Active—E-LMI is operational for this EVC.
-
Inactive—All of the remote UNIs are unreachable or down.
-
New—The EVC has not yet been reported to the CE device.
-
Not
yet known—E-LMI is still waiting to receive the status from CFM. This condition
should not persist for more than a few seconds.
-
Partially Active—One or more of the remote UNIs is unreachable
or down.
|
EVC Type:
|
Type of
the EVC, with the following possible values: "Point-to-Point,"
"Multipoint-to-Multipoint," or "EVC type not yet known."
|
OAM
Protocol:
|
The OAM
protocol from which the EVC status and type are derived. Possible values are
either "CFM" or "None."
|
CFM
Domain:
|
Name of
the CFM domain for this EVC.
|
CFM
Service:
|
Name of
the CFM service for this EVC.
|
Remote UNI
Count: Configured =
x, Active =
y
|
Number of
configured or expected remote UNIs (x) and the number of active remote UNIs (y) within the EVC.
|
Remote UNI
Id:
|
ID of
each remote UNI, including both configured and active remote UNIs where these
two sets are not identical. If the number of configured and active remote UNIs
is zero, no table is displayed.
Note
|
Where
no ID is configured for a remote UNI using the
ethernet uni
id command, then the CFM remote MEP ID is displayed, for example,
"<Remote UNI Reference Id:
x>"
|
|
Status
|
Status of
each remote UNI, with the following possible values: "Up," "Down," "Admin
Down," "Unreachable (a configured remote UNI is not active or missing)," or
"Unknown (a remote UNI is active but not reporting its status)."
|