- Preface
- Command-Line Interface
- action to channel-group
- channel-protocol to class-map
- clear cable-diagnostics tdr to copy /noverify
- define interface-range to duplex
- eigrp event-log-size to mls exclude
- mls flow to pagp port
- platform ip features pisa to process-min-time percent
- rcv-queue to show bootvar
- show cable-diagnostics to show ip cache
- show ip cef to show mls asic
- show mls cef to show qm-sp
- show queueing to show vtp
- shutdown vlan to test cable-diagnostics
- tunnel udlr address-resolution to username
- verify to wrr-queue
- wrr-queue cos-trap to wrr-queue threshold
- Acronyms
- Acknowledgments for Open-Source Software
- show ip cef epoch
- show ip cef inconsistency
- show ip cef summary
- show ip cef vlan
- show ip dhcp relay information trusted-sources
- show ip dhcp snooping
- show ip dhcp snooping binding
- show ip dhcp snooping database
- show ip flow-export
- show ip igmp groups
- show ip igmp interface
- show ip igmp snooping explicit-tracking
- show ip igmp snooping mrouter
- show ip igmp snooping rate-limit
- show ip igmp snooping statistics
- show ip igmp udlr
- show ip interface
- show ip mcache
- show ip mds interface
- show ip mpacket
- show ip mroute
- show ip mroute bidirectional
- show ip msdp count
- show ip msdp peer
- show ip msdp sa-cache
- show ip msdp summary
- show ip nhrp
- show ip pim bsr-router
- show ip pim interface df
- show ip pim mdt bgp
- show ip pim mdt history
- show ip pim mdt receive
- show ip pim mdt send
- show ip pim neighbor
- show ip pim rp-hash
- show ip pim rp mapping
- show ip pim snooping
- show ip rpf events
- show ip wccp
- show ipv6 mfib
- show ipv6 mld snooping
- show l2protocol-tunnel
- show l3-mgr
- show lacp
- show logging ip access-list
- show mac-address-table
- show mac-address-table learning
- show memory dead
- show mls asic
show ip cef epoch
To display the epoch information for the adjacency table and all FIB tables, use the show ip cef epoch command.
show ip cef epoch
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
These show commands also display the epoch information for the following:
•
show ip cef summary—Displays the table epoch for a specific FIB table.
•show ip cef detail—Displays the epoch value for each entry of a specific FIB table.
•show adjacency summary—Displays the adjacency table epoch.
•show adjacency detail—Displays the epoch value for each entry of the adjacency table.
Examples
This example shows how to display epoch information:
Router# show ip cef epoch
CEF epoch information:
Table:Default-table
Table epoch:2 (164 entries at this epoch)
Adjacency table
Table epoch:1 (33 entries at this epoch)
This example shows the output after you clear the epoch table and increment the epoch number:
Router# show ip cef epoch
CEF epoch information:
Table:Default-table
Table epoch:2 (164 entries at this epoch)
Adjacency table
Table epoch:1 (33 entries at this epoch)
Router# clear ip cef epoch full
Router# show ip cef epoch
CEF epoch information:
Table:Default-table
Table epoch:3 (164 entries at this epoch)
Adjacency table
Table epoch:2 (33 entries at this epoch)
Router#
Syntax Description
|
|
|
|---|---|
Begins a new epoch and increments the epoch number for all tables (including the adjacency table). |
|
show ip cef |
Displays entries in the FIB or displays a summary of the FIB. |
show ip cef inconsistency
To display the IP CEF inconsistencies, use the show ip cef inconsistency command.
show ip cef [vrf vrf-name] inconsistency [records [detail]]
Syntax Description
vrf vrf-name |
(Optional) Specifies a VRF instance. |
records |
(Optional) Displays all recorded inconsistencies. |
detail |
(Optional) Displays the detailed information for each CEF table entry. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
This command displays the recorded IP CEF inconsistency records found by the lc-detect, scan-rp, scan-rib, and scan-lc detection mechanisms.
You can configure the IP CEF-prefix consistency-detection mechanisms using the ip cef table consistency-check command.
Examples
This example shows how to display the recorded CEF inconsistency records:
Router# show ip cef inconsistency
Table consistency checkers (settle time 65s)
lc-detect:running
0/0/0 queries sent/ignored/received
scan-lc:running [100 prefixes checked every 60s]
0/0/0 queries sent/ignored/received
scan-rp:running [100 prefixes checked every 60s]
0/0/0 queries sent/ignored/received
scan-rib:running [1000 prefixes checked every 60s]
0/0/0 queries sent/ignored/received
Inconsistencies:0 confirmed, 0/16 recorded
Table 2-46 describes the fields shown in the display.
Related Commands
|
|
|
|---|---|
Clears the statistics and records for the CEF-consistency checker. |
show ip cef summary
To display a summary of the IP CEF table, use the show ip cef summary command.
show ip cef summary
Syntax Description
This command has no keywords and arguments.
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display a summary of the IP CEF table:
Router# show ip cef summary
IP Distributed CEF with switching (Table Version 25), flags=0x0
21 routes, 0 reresolve, 0 unresolved (0 old, 0 new), peak 1
21 leaves, 16 nodes, 19496 bytes, 36 inserts, 15 invalidations
0 load sharing elements, 0 bytes, 0 references
universal per-destination load sharing algorithm, id 5163EC15
3(0) CEF resets, 0 revisions of existing leaves
Resolution Timer: Exponential (currently 1s, peak 1s)
0 in-place/0 aborted modifications
refcounts: 4377 leaf, 4352 node
Table epoch: 0 (21 entries at this epoch)
Adjacency Table has 9 adjacencies
Router#
show ip cef vlan
To display the information about the IP CEF VLAN interface status, the configuration, and the prefixes for a specific interface, use the show ip cef vlan command.
show ip cef vlan vlan-id [detail]
Syntax Description
vlan-id |
VLAN number; valid values are from 1 to 4094. |
detail |
(Optional) Displays the detailed information about the IP CEF VLAN interface. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the prefixes for a specific VLAN:
Router> show ip cef vlan 1003
Prefix Next Hop Interface
0.0.0.0/0 172.20.52.1 FastEthernet3/3
0.0.0.0/32 receive
10.7.0.0/16 172.20.52.1 FastEthernet3/3
10.16.18.0/23 172.20.52.1 FastEthernet3/3
Router>
This example shows how to display detailed IP CEF information for a specific VLAN:
Router> show ip cef vlan 1003 detail
IP Distributed CEF with switching (Table Version 2364), flags=0x0
1383 routes, 0 reresolve, 0 unresolved (0 old, 0 new)
1383 leaves, 201 nodes, 380532 bytes, 2372 inserts, 989 invalidations
0 load sharing elements, 0 bytes, 0 references
universal per-destination load sharing algorithm, id 9B6C9823
3 CEF resets, 0 revisions of existing leaves
refcounts: 54276 leaf, 51712 node
Adjacency Table has 5 adjacencies
Router>
show ip dhcp relay information trusted-sources
To list all the configured trusted interfaces, use the show ip dhcp relay information trusted-sources command.
show ip dhcp relay information trusted-sources
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display a list of all the configured trusted interfaces:
Router# show ip dhcp relay information trusted-sources
List of trusted sources of relay agent information option:
Vlan60 Vlan62
Router#
Related Commands
|
|
|
|---|---|
Enables all the interfaces as trusted sources of the DHCP relay-agent information option. |
|
Enables an interface as a trusted source of the DHCP relay-agent information. |
show ip dhcp snooping
To display the DHCP snooping configuration, use the show ip dhcp snooping command.
show ip dhcp snooping [statistics [detail]]
Syntax Description
statistics |
(Optional) Displays statistics information about DHCP snooping. |
detail |
(Optional) Displays the detailed information about DHCP snooping. |
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the DHCP snooping configuration:
Router# show ip dhcp snooping
Switch DHCP snooping is enabled
DHCP snooping is configured on following VLANs:
5 10
Insertion of option 82 is enabled
Interface Trusted Rate limit (pps)
-------------------- ------- ----------------
FastEthernet6/11 no 10
FastEthernet6/36 yes 50
Router#
This example shows how to display the DHCP snooping statistics information:
Router# show ip dhcp snooping statistics
Packets Processed by DHCP Snooping = 0
Packets Dropped Because
IDB not known = 0
Queue full = 0
Interface is in errdisabled = 0
Rate limit exceeded = 0
Received on untrusted ports = 0
Nonzero giaddr = 0
Source mac not equal to chaddr = 0
No binding entry = 0
Insertion of opt82 fail = 0
Unknown packet = 0
Interface Down = 0
Unknown output interface = 0
Router#
This example shows how to display detailed DHCP snooping statistics information:
Router# show ip dhcp snooping statistics detail
Packets Forwarded = 0
Packets Dropped = 0
Packets Dropped From untrusted ports = 0
Router#
Related Commands
show ip dhcp snooping binding
To display the DHCP snooping binding entries, use the show ip dhcp snooping binding command.
show ip dhcp snooping binding [ip-address] [mac-address] [vlan vlan]
[interface interface interface-num]
Syntax Description
Command Default
If no argument is specified, the switch displays the entire DHCP snooping binding table.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
DHCP snooping is enabled on a VLAN only if both the global snooping and the VLAN snooping are enabled.
Examples
This example shows how to display the DHCP snooping binding entries for a switch:
Router# show ip dhcp snooping binding
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------- ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Router#
This example shows how to display an IP address for DHCP snooping binding entries:
Router# show ip dhcp snooping binding 172.100.101.102
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------- ----- ------------ 0000.0100.0201 172.100.101.102 1600 dhcp-snooping 100 FastEthernet3/1
Router#
This example shows how to display the MAC address for the DHCP snooping binding entries:
Router# show ip dhcp snooping binding 55.5.5.2 0002.b33f.3d5f
MacAddress IpAddress Lease(sec) Type VLAN Interface
------------------ --------------- ---------- ------------- ---- --------------------
00:02:B3:3F:3D:5F 55.5.5.2 492 dhcp-snooping 99 FastEthernet6/36
Router#
This example shows how to display the DHCP snooping binding entries' MAC address for a specific VLAN:
Router# show ip dhcp snooping binding 55.5.5.2 0002.b33f.3d5f vlan 99
MacAddress IpAddress Lease(sec) Type VLAN Interface
------------------ --------------- ---------- ------------- ---- --------------------
00:02:B3:3F:3D:5F 55.5.5.2 479 dhcp-snooping 99 FastEthernet6/36
Router#
This example shows how to display the dynamic DHCP snooping binding entries:
Router# show ip dhcp snooping binding dynamic
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------ ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Router#
This example shows how to display the DHCP snooping binding entries on VLAN 100:
Router# show ip dhcp snooping binding vlan 100
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------ ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Router#
This example shows how to display the DHCP snooping binding entries on Ethernet interface 0/1:
Router# show ip dhcp snooping binding interface fastethernet3/1
MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------ ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping 100 FastEthernet3/1
Router#
Table 2-47 describes the fields in the show ip dhcp snooping command output.
Related Commands
show ip dhcp snooping database
To display the status of the DHCP snooping database agent, use the show ip dhcp snooping database command.
show ip dhcp snooping database [detail]
Syntax Description
detail |
(Optional) Provides additional operating state and statistics information. |
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the DHCP snooping database:
Router# show ip dhcp snooping database
Agent URL :
Write delay Timer : 300 seconds
Abort Timer : 300 seconds
Agent Running : No
Delay Timer Expiry : Not Running
Abort Timer Expiry : Not Running
Last Succeded Time : None
Last Failed Time : None
Last Failed Reason : No failure recorded.
Total Attempts : 0 Startup Failures : 0
Successful Transfers : 0 Failed Transfers : 0
Successful Reads : 0 Failed Reads : 0
Successful Writes : 0 Failed Writes : 0
Media Failures : 0
Router#
This example shows how to view additional operating statistics:
Router# show ip dhcp snooping database detail
Agent URL : tftp://10.1.1.1/directory/file
Write delay Timer : 300 seconds
Abort Timer : 300 seconds
Agent Running : No
Delay Timer Expiry : 7 (00:00:07)
Abort Timer Expiry : Not Running
Last Succeded Time : None
Last Failed Time : 17:14:25 UTC Sat Jul 7 2001
Last Failed Reason : Unable to access URL.
Total Attempts : 21 Startup Failures : 0
Successful Transfers : 0 Failed Transfers : 21
Successful Reads : 0 Failed Reads : 0
Successful Writes : 0 Failed Writes : 21
Media Failures : 0
First successful access: Read
Last ignored bindings counters :
Binding Collisions : 0 Expired leases : 0
Invalid interfaces : 0 Unsupported vlans : 0
Parse failures : 0
Last Ignored Time : None
Total ignored bindings counters:
Binding Collisions : 0 Expired leases : 0
Invalid interfaces : 0 Unsupported vlans : 0
Parse failures : 0
Router#
Related Commands
show ip flow-export
To display the information about the software-switched flows for the data export, including the main cache and all other enabled caches, use the show ip flow export command.
show ip flow export [template | verbose]
Syntax Description
template |
(Optional) Displays export template statistics information. |
verbose |
(Optional) Displays verbose export statistics information. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the information about the software-switched flows for NDE:
Router# show ip flow export
Flow export v1 is disabled for main cache
Version 1 flow records
0 flows exported in 0 udp datagrams
0 flows failed due to lack of export packet
0 export packets were sent up to process level
0 export packets were dropped due to no fib
0 export packets were dropped due to adjacency issues
0 export packets were dropped due to fragmentation failures
0 export packets were dropped due to encapsulation fixup failures
0 export packets were dropped enqueuing for the RP
0 export packets were dropped due to IPC rate limiting
Router#
This example shows how to display export template statistics information:
Router# show ip flow export template
No Template export information
No Option Templates exist
Template Options Flag = 0
Total number of Templates added = 0
Total active Templates = 0
Flow Templates active = 0
Flow Templates added = 0
Option Templates active = 0
Option Templates added = 0
Template ager polls = 0
Option Template ager polls = 0
Main cache version 9 export is disabled
Router#
This example shows how to display export verbose statistics information:
Router# show ip flow export verbose
Flow export v1 is disabled for main cache
Version 1 flow records
0 flows exported in 0 udp datagrams
0 flows failed due to lack of export packet
0 export packets were sent up to process level
0 export packets were dropped due to no fib
0 export packets were dropped due to adjacency issues
0 export packets were dropped due to fragmentation failures
0 export packets were dropped due to encapsulation fixup failures
0 export packets were dropped enqueuing for the RP
0 export packets were dropped due to IPC rate limiting
Router#
Related Commands
|
|
|
|---|---|
clear adjacency |
Clears the CEF adjacency table. |
ip flow-aggregation cache |
Creates a flow-aggregation cache and enters the aggregation cache configuration mode. |
show ip igmp groups
To display the multicast groups with receivers that are directly connected to the router and that were learned through IGMP, use the show ip igmp groups command.
show ip igmp [vrf vrf-name] groups [group-name | group-address | interface-type interface-number] [detail]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
If you omit all optional arguments and keywords, the show ip igmp groups command displays all directly connected multicast groups by group address, interface type, and interface number.
Examples
This example shows how to display output from the show ip igmp groups command:
Router# show ip igmp groups
IGMP Connected Group Membership
Group Address Interface Uptime Expires Last Reporter
239.255.255.254 Ethernet3/1 1w0d 00:02:19 172.21.200.159
224.0.1.40 Ethernet3/1 1w0d 00:02:15 172.21.200.1
224.0.1.40 Ethernet3/3 1w0d never 172.16.214.251
224.0.1.1 Ethernet3/1 1w0d 00:02:11 172.21.200.11
224.9.9.2 Ethernet3/1 1w0d 00:02:10 172.21.200.155
232.1.1.1 Ethernet3/1 5d21h stopped 172.21.200.206
This example shows how to display output from the show ip igmp groups command with the group-address argument and detail keyword:
Router# show ip igmp groups 232.1.1.1 detail
Interface: Ethernet3/2
Group: 232.1.1.1
Uptime: 01:58:28
Group mode: INCLUDE
Last reporter: 10.0.119.133
CSR Grp Exp: 00:02:38
Group source list: (C - Cisco Src Report, U - URD, R - Remote)
Source Address Uptime v3 Exp CSR Exp Fwd Flags
172.16.214.1 01:58:28 stopped 00:02:31 Yes C
Table 2-48 describes the fields shown in the displays.
Related Commands
|
|
|
|---|---|
ip igmp query-interval |
Configures the frequency at which Cisco IOS software sends IGMP host query messages. |
show ip igmp interface
To display the information about the IGMP-interface status and configuration, use the show ip igmp interface command.
show ip igmp [vrf vrf-name] interface [{interface [interface-number]} | {null interface-number} | {vlan vlan-id}]
Syntax Description
Command Default
If you do not specify a VLAN, information for VLAN 1 is shown.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.
If you omit the optional arguments, the show ip igmp interface command displays information about all interfaces.
Examples
This example shows how to display IGMP information for VLAN 43:
Router# show ip igmp interface vlan 43
Vlan43 is up, line protocol is up
Internet address is 43.0.0.1/24
IGMP is enabled on interface
Current IGMP host version is 2
Current IGMP router version is 2
IGMP query interval is 60 seconds
IGMP querier timeout is 120 seconds
IGMP max query response time is 10 seconds
Last member query count is 2
Last member query response interval is 1000 ms
Inbound IGMP access group is not set
IGMP activity: 1 joins, 0 leaves
Multicast routing is enabled on interface
Multicast TTL threshold is 0
Multicast designated router (DR) is 43.0.0.1 (this system)
IGMP querying router is 43.0.0.1 (this system)
Multicast groups joined by this system (number of users):
224.0.1.40(1)
IGMP snooping is globally enabled
IGMP snooping is enabled on this interface
IGMP snooping fast-leave is disabled and querier is disabled
IGMP snooping explicit-tracking is enabled on this interface
IGMP snooping last member query interval on this interface is 1000 ms
Router#
Related Commands
|
|
|
|---|---|
Deletes the entries for the IGMP-group cache. |
|
Displays the information about the dynamically learned and manually configured multicast router interfaces. |
show ip igmp snooping explicit-tracking
To display the information about the explicit host-tracking status for IGMPv3 hosts, use the show ip igmp snooping explicit-tracking command.
show ip igmp snooping explicit-tracking {vlan vlan-id}
Syntax Description
vlan vlan-id |
Specifies the VLAN; see the "Usage Guidelines" section for valid values. |
Command Default
If you do not specify a VLAN, information for VLAN 1 is shown.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
Explicit host tracking is supported only with IGMPv3 hosts.
Examples
This example shows how to display the information about the explicit host-tracking status for IGMPv3 hosts:
Router# show ip igmp snooping explicit-tracking vlan 25
Source/Group Interface Reporter Filter_mode
------------------------------------------------------------------------
10.1.1.1/226.2.2.2 Vl25:1/2 16.27.2.3 INCLUDE
10.2.2.2/226.2.2.2 Vl25:1/2 16.27.2.3 INCLUDE
Router#
Related Commands
|
|
|
|---|---|
Enables explicit host tracking. |
show ip igmp snooping mrouter
To display the information about the dynamically learned and manually configured multicast router interfaces, use the show ip igmp snooping mrouter command.
show ip igmp snooping mrouter [{vlan vlan-id}]
Syntax Description
vlan vlan-id |
(Optional) Specifies a VLAN; valid values are from 1 to 4094. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
You can also use the show mac-address-table command to display entries in the MAC-address table for a VLAN that has IGMP snooping enabled.
You can display IGMP snooping information for VLAN interfaces by entering the show ip igmp vlan vlan-num command.
Examples
This example shows how to display the information about IGMP snooping for a specific VLAN:
Router# show ip igmp snooping mrouter vlan 1
vlan ports
-----+----------------------------------------
1 Gi1/1,Gi2/1,Fa3/48,Router
Router#
Related Commands
|
|
|
|---|---|
Configures a Layer 2 port as a multicast router port. |
show ip igmp snooping rate-limit
To display the information about the IGMP snooping rate limit, use the show ip igmp snooping rate-limit command.
show ip igmp snooping rate-limit [statistics | vlan vlan-id]
Syntax Description
statistics |
(Optional) Displays IGMP snooping statistics. |
vlan vlan-id |
(Optional) Specifies a VLAN; valid values are from 1 to 4094. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the statistics for IGMP snooping rate limiting:
Router# show ip igmp snooping rate-limit statistics
Max IGMP messages incoming rate : Not configured
Vlan Incoming rate Rate-limiting ON Disable count Time to Enable
-----+---------------+----------------+---------------+---------------+
222 1000 No 0
111 5999 Yes 3 185
Router#
This example shows how to display IGMP snooping rate-limit information for a specific VLAN:
Router# show ip igmp snooping rate-limit vlan 19
Max IGMP messages incoming rate : 200 pps
Vlan Incoming IGMP rate (in pps)
--------+---------------------------------
19 200
Router#
Related Commands
|
|
|
|---|---|
Sets the rate limit for IGMP snooping packets. |
show ip igmp snooping statistics
To display IGMPv3 statistics, use the show ip igmp snooping statistics command.
show ip igmp snooping statistics [{interface interface [interface-number]} | {port-channel number} | {vlan vlan-id}]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The show ip igmp snooping statistics command displays the following statistics:
•List of ports that are members of a group
•Filter mode
•Reporter-address behind the port
•Additional information (such as the last-join and last-leave collected since the previous time that a clear ip igmp snooping statistics command was issued)
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.
The port-channel number values from 257 to 282 are supported on the CSM and the FWSM only.
The #hosts behind the VLAN is displayed only if you define the max-hosts policy on the specified VLAN and enable the log policy for the specified VLAN.
Examples
This example shows how to display IGMPv3 statistics:
Router# show ip igmp snooping statistics interface FastEthernet5/1
IGMP Snooping statistics
Service-policy: Policy1policy tied with this interface
#Channels: 3
#hosts : 3
Query Rx: 2901 GS Query Rx: 0 V3 Query Tot Rx: 0
Join Rx: 8686 Leave Rx: 0 V3 Report Rx: 2300
Join Rx from router ports: 8684 Leave Rx from router ports: 0
Total Rx: 11587
Channel/Group Interface Reporter Uptime Last-Join Last-Leave
10.7.20.1,239.1.1.1 F5/1 10.5.20.1 00:12:00 1:10:00 -
10.7.30.1,239.1.1.1 F5/1 10.5.30.1 00:50:10 1:10:02 0:30:02
10.7.40.1,239.1.1.1 F5/1 10.5.40.1 00:10:10 1:10:03 -
Router#
Table 2-49 describes the fields that are shown in the example.
Related Commands
|
|
|
|---|---|
Clears the IGMP snooping statistics. |
show ip igmp udlr
To display UDLR information for the connected multicast groups on the interfaces that have a UDL helper address configured, use the show ip igmp udlr command.
show ip igmp udlr [group-name | group-address | interface-type interface-number]
Syntax Description
group-name |
(Optional) Name of the multicast group. |
group-address |
(Optional) Address of the multicast group. |
interface-type interface-number |
(Optional) Interface type and number. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
This command displays which groups are being forwarded and received over the UDL.
On the upstream router, this command shows which interface is a UDL interface and which IP multicast groups are being forwarded out that interface. The UDL Reporter is the IP address of the downstream interface on the receiving router. If there is more than one downstream router, this field shows which downstream router forwarded the IGMP host report to the upstream router over the ground-based network. This report is forwarded over the UDL so that all downstream routers know which groups have already been requested by other downstream routers, and additional IGMP host reports are suppressed.
On the downstream router, this command (in the Interface field) shows which local interface received an IGMP host report (from a connected host for a specific group). The UDL Reporter is the IP address of the router that had forwarded the IGMP host report to the upstream router over the ground-based network. The UDL Interfaces column shows the interface on which IP multicast packets are being received.
Examples
This example shows the output of the show ip igmp udlr command on an upstream router:
Router# show ip igmp udlr
IGMP UDLR Status, UDL Interfaces: Serial0
Group Address Interface UDL Reporter Reporter Expires
224.2.127.254 Serial0 10.0.0.2 00:02:12
224.0.1.40 Serial0 10.0.0.2 00:02:11
225.7.7.7 Serial0 10.0.0.2 00:02:15
Router#
This example shows the output of the show ip igmp udlr command on a downstream router:
Router# show ip igmp udlr
IGMP UDLR Status, UDL Interfaces: Serial0
Group Address Interface UDL Reporter Reporter Expires
224.2.127.254 Serial0 10.0.0.2 00:02:49
224.0.1.40 Serial0 10.0.0.2 00:02:48
225.7.7.7 Serial0 10.0.0.2 00:02:52
Router#
Table 2-50 describes the fields shown in the output of the show ip igmp udlr command.
show ip interface
To display the usability status of interfaces that are configured for IP, use the show ip interface command.
show ip interface [type number]
Syntax Description
type |
(Optional) Interface type. |
number |
(Optional) Interface number. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The Cisco IOS software automatically enters a directly connected route in the routing table if the interface is usable. A usable interface is one through which the software can send and receive packets. If the software determines that an interface is not usable, it removes the directly connected routing entry from the routing table. Removing the entry allows the software to use dynamic routing protocols to determine backup routes to the network, if any.
If the interface can provide two-way communication, the line protocol is marked "up." If the interface hardware is usable, the interface is marked "up."
If you specify an optional interface type, you see only information on that specific interface.
If you specify no optional arguments, you see information on all the interfaces.
When an asynchronous interface is encapsulated with PPP or Serial Line Internet Protocol (SLIP), IP fast switching is enabled. The show ip interface command on an asynchronous interface that is encapsulated with PPP or SLIP displays a message indicating that IP fast switching is enabled.
Examples
This example shows how to display the usability status for a specific VLAN:
Router# show ip interface vlan 1
Vlan1 is up, line protocol is up
Internet address is 10.6.58.4/24
Broadcast address is 255.255.255.255
Address determined by non-volatile memory
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP Fast switching turbo vector
IP Normal CEF switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast, CEF
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Probe proxy name replies are disabled
Policy routing is disabled
Network address translation is disabled
WCCP Redirect outbound is disabled
WCCP Redirect inbound is disabled
WCCP Redirect exclude is disabled
BGP Policy Mapping is disabled
Sampled Netflow is disabled
IP multicast multilayer switching is disabled
Netflow Data Export (hardware) is enabled
Router#
Table 2-51 describes the fields that are shown in the example.
show ip mcache
To display the contents of the IP fast-switching cache, use the show ip mcache command.
show ip mcache [vrf vrf-name] [group-address | group-name] [source-address | source-name]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The group-address | group-name can be either a Class D IP address or a DNS name.
The source-address | source-name can be either a unicast IP address or a DNS name.
Examples
This example shows how to display the contents of the IP fast-switching cache. This entry shows a specific source (wrn-source 226.62.246.73) sending to the World Radio Network group (224.2.143.24):
Router> show ip mcache wrn wrn-source
IP Multicast Fast-Switching Cache
(226.62.246.73/32, 224.2.143.24), Fddi0, Last used: 00:00:00
Ethernet0 MAC Header: 01005E028F1800000C1883D30800
Ethernet1 MAC Header: 01005E028F1800000C1883D60800
Ethernet2 MAC Header: 01005E028F1800000C1883D40800
Ethernet3 MAC Header: 01005E028F1800000C1883D70800
Table 2-52 describes the fields shown in the display.
show ip mds interface
To display MDS information for all the interfaces on the module, use the show ip mds interface command.
show ip mds interface [vrf vrf-name]
Syntax Description
vrf vrf-name |
(Optional) Specifies the name that is assigned to the multicast VPN routing and forwarding (VRF) instance. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display MDS information for all the interfaces on the module:
Router# show ip mds interface
Interface SW-Index HW-Index HW IDB FS Vector VRF
Ethernet1/0/0 2 1 0x60C2DB40 0x602FB7A4 default
Ethernet1/0/1 3 2 0x60C32280 0x603D52B8 default
Ethernet1/0/2 4 3 0x60C35E40 0x602FB7A4 default
Ethernet1/0/3 5 4 0x60C39E60 0x603D52B8 default
Ethernet1/0/4 6 5 0x60C3D780 0x602FB7A4 default
Ethernet1/0/5 7 6 0x60C41140 0x602FB7A4 default
Ethernet1/0/6 8 7 0x60C453A0 0x602FB7A4 default
Ethernet1/0/7 9 8 0x60C48DC0 0x602FB7A4 default
POS2/0/0 10 9 0x0 default
POS3/0/0 11 10 0x0 default
Virtual-Access1 13 11 0x0 default
Loopback0 14 12 0x0 default
Tunnel0 15 23 0x61C2E480 0x603D52B8 vrf1
Tunnel1 16 24 0x61C267E0 0x603D52B8 vrf2
Ethernet1/0/3.1 17 4 0x60C39E60 0x603D52B8 vrf1
Ethernet1/0/3.2 18 4 0x60C39E60 0x603D52B8 vrf2
Table 2-53 describes the fields shown in the display.
show ip mpacket
To display the contents of the circular cache-header buffer, use the show ip mpacket command.
show ip mpacket [vrf vrf-name] [group-address | group-name] [source-address | source-name] [detail]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
This command is applicable only when the ip multicast cache-headers command is in effect.
Each time that this command is entered, a new buffer is allocated. The summary display (when the detail keyword is omitted) shows the IP packet identifier, time-to-live (TTL) value, source and destination IP addresses, and a local time stamp when the packet was received.
The two arguments and one keyword can be used in the same command in any combination.
Examples
This example shows how to display the contents of the circular cache-header buffer:
Router # show ip mpacket smallgroup
IP Multicast Header Cache - entry count:6, next index: 7
Key: id/ttl timestamp (name) source group
D782/117 206416.908 (ABC-xy.company.com) 192.168.228.10 224.5.6.7
7302/113 206417.908 (school.edu) 147.12.2.17 224.5.6.7
6CB2/114 206417.412 (MSSRS.company.com) 154.2.19.40 224.5.6.7
D782/117 206417.868 (ABC-xy.company.com) 192.168.228.10 224.5.6.7
E2E9/123 206418.488 (Newman.com) 211.1.8.10 224.5.6.7
1CA7/127 206418.544 (teller.company.com) 192.168.6.10 224.5.6.7
Table 2-54 describes the fields shown in the display.
Related Commands
|
|
|
|---|---|
Allocates a circular buffer to store IP multicast packet headers that the router receives. |
show ip mroute
To display the information about the IP-multicast routing table, use the show ip mroute command.
show ip mroute [vrf vrf-name] [{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id} | {{host-name | host-address} [source]} | {active [kbps | {interface-type num}]} | {count | pruned | static | summary}]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
If you omit all optional arguments and keywords, the show ip mroute command displays all entries in the IP-multicast routing table.
The show ip mroute active kbps command displays all sources sending at a rate greater than or equal to kbps.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.
The port-channel number values are from 257 to 282 are supported on the CSM and the FWSM only.
The multicast routing table is populated by creating source, group (S,G) entries from star, group (*,G) entries. The star refers to all source addresses, the "S" refers to a single source address, and the "G" is the destination multicast group address. In creating (S,G) entries, the software uses the best path to that destination group that is found in the unicast routing table (through RPF).
Examples
This example shows how to display all entries in the IP-multicast routing table:
Router# show ip mroute 224.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate MSDP Advertisement,
U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel
Y - Joined MDT-data group, y - Sending to MDT-data group, s - SSM
Outgoing interface flags: H - Hardware switched
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 224.1.1.1), 00:00:07/00:02:59, RP 2.0.0.1, flags: BC
Bidir-Upstream: Null, RPF nbr 0.0.0.0, RPF-MFD
Outgoing interface list:
Vlan202, Forward/Sparse-Dense, 00:00:07/00:02:59, H
Router#
This example shows how to display the rate that active sources are sending to multicast groups and to display only active sources sending at greater than the default rate:
Router# show ip mroute active
Active IP Multicast Sources - sending >= 4 kbps
Group: 224.2.127.254, (sdr.cisco.com)
Source: 146.137.28.69 (mbone.ipd.anl.gov)
Rate: 1 pps/4 kbps(1sec), 4 kbps(last 1 secs), 4 kbps(life avg)
Group: 224.2.201.241, ACM 97
Source: 130.129.52.160 (webcast3-e1.acm97.interop.net)
Rate: 9 pps/93 kbps(1sec), 145 kbps(last 20 secs), 85 kbps(life avg)
Group: 224.2.207.215, ACM 97
Source: 130.129.52.160 (webcast3-e1.acm97.interop.net)
Rate: 3 pps/31 kbps(1sec), 63 kbps(last 19 secs), 65 kbps(life avg)
Router#
This example shows how to display the information about the route and packet count:
Router# show ip mroute count
IP Multicast Statistics
56 routes using 28552 bytes of memory
13 groups, 3.30 average sources per group
Forwarding Counts:Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second
Other counts:Total/RPF failed/Other drops(OIF-null, rate-limit etc)
Group:224.2.136.89, Source count:1, Group pkt count:29051
Source:132.206.72.28/32, Forwarding:29051/-278/1186/0, Other:85724/8/56665
Router#
This example shows how to display summary information:
Router# show ip mroute summary
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, s - SSM Group, C - Connected, L - Local,
P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set,
J - Join SPT, M - MSDP created entry, X - Proxy Join Timer Running
A - Advertised via MSDP, U - URD, I - Received Source Specific Host
Report
Outgoing interface flags: H - Hardware switched
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
Router#
Table 2-55 describes the fields that are shown in the example.
Related Commands
|
|
|
|---|---|
ip multicast-routing |
Enables IP multicast routing. |
ip pim |
Enables PIM on an interface. |
show ip mroute bidirectional
To display Bidir information from the IP-multicast routing table, use the show ip mroute bidirectional command.
show ip mroute bidirectional [{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id} | {{host-name | host-address} [source]} | {active [kbps | {interface-type num}]} | {count | pruned | static | summary}]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
If you omit all optional arguments and keywords, the mroute bidirectional command displays all entries in the IP-multicast routing table.
Examples
This example shows how to display the information in the IP-multicast routing table that is related to bidirectional PIM:
Router# show ip mroute bidirectional
(*, 225.1.3.0), 00:00:02/00:02:57, RP 3.3.3.3, flags:BC
Bidir-Upstream:GigabitEthernet2/1, RPF nbr 10.53.1.7, RPF-MFD
Outgoing interface list:
GigabitEthernet2/1, Bidir-Upstream/Sparse-Dense, 00:00:02/00:00:00,H
Vlan30, Forward/Sparse-Dense, 00:00:02/00:02:57, H
(*, 225.1.2.0), 00:00:04/00:02:55, RP 3.3.3.3, flags:BC
Bidir-Upstream:GigabitEthernet2/1, RPF nbr 10.53.1.7, RPF-MFD
Outgoing interface list:
GigabitEthernet2/1, Bidir-Upstream/Sparse-Dense, 00:00:04/00:00:00,H
Vlan30, Forward/Sparse-Dense, 00:00:04/00:02:55, H
(*, 225.1.4.1), 00:00:00/00:02:59, RP 3.3.3.3, flags:BC
Bidir-Upstream:GigabitEthernet2/1, RPF nbr 10.53.1.7, RPF-MFD
Outgoing interface list:
GigabitEthernet2/1, Bidir-Upstream/Sparse-Dense, 00:00:00/00:00:00,H
Vlan30, Forward/Sparse-Dense, 00:00:00/00:02:59, H
Router#
show ip msdp count
To display the number of sources and groups that originated in MSDP source-active messages and the number of source-active messages from an MSDP peer in the source-active cache, use the show ip msdp count command.
show ip msdp [vrf vrf-name] count [as-number]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
You must enter the ip msdp cache-sa-state command for this command to obtain any output from the show ip msdp command.
Examples
This example shows how to display the number of sources and groups that originated in MSDP source-active messages and the number of source-active messages from an MSDP peer in the source-active cache:
Router# show ip msdp count
SA State per Peer Counters, <Peer>: <# SA learned>
224.135.250.116: 24
172.16.240.253: 3964
172.16.253.19: 10
172.16.170.110: 11
SA State per ASN Counters, <asn>: <# sources>/<# groups>
Total entries: 4009
?: 192/98, 9: 1/1, 14: 107/57, 17: 7/5
18: 4/3, 25: 23/17, 26: 39/27, 27: 2/2
32: 19/7, 38: 2/1, 52: 4/4, 57: 1/1
68: 4/4, 73: 12/8, 81: 19/1, 87: 9/6
.
.
.
Table 2-56 describes the fields shown in the display.
Related Commands
|
|
|
|---|---|
Creates a source-active state on the router. |
show ip msdp peer
To display detailed information about the MSDP peer, use the show ip msdp peer command.
show ip msdp [vrf vrf-name] peer [peer-address | peer-name]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display detailed information about the MSDP peer:
Router# show ip msdp peer 224.135.250.116
MSDP Peer 224.135.250.116 (rtp5-rp1.cisco.com), AS 109 (configured AS)
Description:
Connection status:
State: Up, Resets: 9, Connection source: Loopback2 (228.69.199.17)
Uptime(Downtime): 1d10h, Messages sent/received: 436765/429062
Output messages discarded: 0
Connection and counters cleared 1w2d ago
SA Filtering:
Input (S,G) filter: none, route-map: none
Input RP filter: none, route-map: none
Output (S,G) filter: none, route-map: none
Output RP filter: none, route-map: none
SA-Requests:
Input filter: none
Sending SA-Requests to peer: disabled
Peer ttl threshold: 0
SAs learned from this peer: 32, SAs limit: 500
Input queue size: 0, Output queue size: 0
Table 2-57 describes the fields shown in the display.
Related Commands
|
|
|
|---|---|
Configures an MSDP peer. |
show ip msdp sa-cache
To display the (S,G) state that is learned from MSDP peers, use the show ip msdp sa-cache command.
show ip msdp [vrf vrf-name] sa-cache [group-address | source-address | group-name | source-name] [group-address | source-address | group-name | source-name] [as-number]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The state is cached only if you enter the ip msdp cache-sa-state command.
If you specify two addresses or names, an (S,G) entry corresponding to those addresses is displayed. If you specify one group address only, all sources for that group are displayed.
If no options are specified, the entire source-active cache is displayed.
Examples
This example shows how to display the (S,G) state that is learned from MSDP peers:
Router# show ip msdp sa-cache
MSDP Source-Active Cache - 2398 entries
(172.16.41.33, 238.105.148.0), RP 172.16.3.111, MBGP/AS 704, 2d10h/00:05:33
(172.16.112.8, 224.2.0.1), RP 192.168.200.65, MBGP/AS 10888, 00:03:21/00:02:38
(172.16.10.13, 227.37.32.1), RP 192.168.3.92, MBGP/AS 704, 05:22:20/00:03:32
(172.16.66.18, 233.0.0.1), RP 192.168.3.111, MBGP/AS 704, 2d10h/00:05:35
(172.16.66.148, 233.0.0.1), RP 192.168.3.111, MBGP/AS 704, 2d10h/00:05:35
(172.16.10.13, 227.37.32.2), RP 192.168.3.92, MBGP/AS 704, 00:44:30/00:01:31
(172.16.70.203, 224.2.236.2), RP 192.168.253.7, MBGP/AS 3582, 02:34:16/00:05:49
(172.18.42.104, 236.195.56.2), RP 192.168.3.92, MBGP/AS 704, 04:21:13/00:05:22
(172.16.10.13, 227.37.32.3), RP 192.168.3.92, MBGP/AS 704, 00:44:30/00:02:31
(172.18.15.43, 224.0.92.3), RP 192.168.200.65, MBGP/AS 10888, 6d09h/00:05:35
(172.18.15.111, 224.0.92.3), RP 192.168.200.65, MBGP/AS 10888, 16:18:08/00:05:35
(172.18.21.45, 224.0.92.3), RP 192.168.200.65, MBGP/AS 10888, 16:18:08/00:05:35
(172.18.15.75, 224.0.92.3), RP 192.168.200.65, MBGP/AS 10888, 08:40:52/00:05:35
(172.18.15.100, 224.0.92.3), RP 192.168.200.65, MBGP/AS 10888, 08:40:52/00:05:35
(172.16.10.13, 227.37.32.6), RP 192.168.3.92, MBGP/AS 704, 00:45:30/00:05:31
(172.18.41.33, 224.247.228.10), RP 192.168.3.111, MBGP/AS 704, 2d10h/00:05:35
(172.18.222.210, 224.2.224.13), RP 192.168.3.92, MBGP/AS 704, 01:51:53/00:05:22
(172.18.41.33, 229.231.124.13), RP 192.168.3.111, MBGP/AS 704, 2d10h/00:05:33
(172.18.32.138, 224.2.200.23), RP 192.168.253.7, MBGP/AS 3582, 21:33:40/00:05:49
(172.18.75.244, 224.2.200.23), RP 192.168.253.7, MBGP/AS 3582, 21:33:40/00:05:49
Table 2-58 describes the fields shown in the display.
Related Commands
|
|
|
|---|---|
clear ip msdp sa-cache |
Clears MSDP source active cache entries. |
Creates a source-active state on the router. |
show ip msdp summary
To display the MSDP peer status, use the show ip msdp summary command.
show ip msdp [vrf vrf-name] summary
Syntax Description
vrf vrf-name |
(Optional) Specifies the name that is assigned to the multicast VPN routing and forwarding (VRF) instance. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the MSDP peer status:
Router# show ip msdp summary
MSDP Peer Status Summary
Peer Address AS State Uptime/ Reset SA Peer Name
Downtime Count Count
224.135.250.116 109 Up 1d10h 9 111 rtp5-rp1
*172.20.240.253 1239 Up 14:24:00 5 4010 sl-rp-stk
172.16.253.19 109 Up 12:36:17 5 10 shinjuku-rp1
172.16.170.110 109 Up 1d11h 9 12 ams-rp1
Table 2-59 describes the fields shown in the display.
show ip nhrp
To display information about the NHRP cache, use the show ip nhrp command.
show ip nhrp [summary | dynamic | static | incomplete] [{interface-type interface-number} | ip-address] [detail | brief]
Syntax Description
summary |
(Optional) Displays a summary of NHRP cache purge information. |
dynamic |
(Optional) Displays the dynamic (learned) IP-to-NBMA cache entries only. |
static |
(Optional) Displays the static IP-to-NBMA address cache entries only (configured using the ip nhrp map command). |
incomplete |
(Optional) Displays information about an incomplete cache. |
interface-type interface-number |
(Optional) NHRP cache information for the specified interface type only; see Table 2-60 for types, number ranges, and descriptions. |
ip-address |
(Optional) NHRP cache information for the specified IP address only. |
detail |
(Optional) Displays detailed information about the NHRP cache. |
brief |
(Optional) Displays basic information about the NHRP cache. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
Table 2-60 lists the valid types, number ranges, and descriptions for the type and number optional arguments.
Note The valid types can vary according to the platform and interfaces on the platform.
Examples
This example shows how to display information about the NHRP cache:
Router# show ip nhrp
10.0.0.2 255.255.255.255, ATM0/0 created 0:00:43 expire 1:59:16
Type: dynamic Flags: authoritative
NBMA address: 11.1111.1111.1111.1111.1111.1111.1111.1111.1111.11
10.0.0.1 255.255.255.255, Tunnel0 created 0:10:03 expire 1:49:56
Type: static Flags: authoritative
NBMA address: 11.1.1.2
Table 2-61 describes the fields shown in the display.
This example shows how to display basic information about the dynamic (learned) IP-to-NBMA cache entries only for a specific IP address:
Router# show ip nhrp dynamic 255.255.255.255 brief
Target Via NBMA Mode Intfc Claimed
Related Commands
show ip pim bsr-router
To display the BSR information, use the show ip pim bsr-router command.
show ip pim vrf vrf-name bsr-router
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VPN routing and forwarding (VRF) instance. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The output includes elected BSR information and information about the locally configured candidate rendezvous-point advertisement.
Examples
This example shows how to display the BSR information:
Router# show ip pim bsr-router
PIMv2 Bootstrap information
This system is the Bootstrap Router (BSR)
BSR address: 172.16.143.28
Uptime: 04:37:59, BSR Priority: 4, Hash mask length: 30
Next bootstrap message in 00:00:03 seconds
Next Cand_RP_advertisement in 00:00:03 seconds.
RP: 172.16.143.28(Ethernet0), Group acl: 6
Table 2-62 describes the fields shown in the display.
|
|
|
|---|---|
BSR address |
IP address of the bootstrap router. |
Uptime |
Length of time that this router has been up, in hours, minutes, and seconds. |
BSR Priority |
Priority as configured in the ip pim bsr-candidate command. |
Hash mask length |
Length of a mask (32 bits maximum) that is to be ANDed with the group address before the hash function is called. This value is configured in the ip pim bsr-candidate command. |
Next bootstrap message in |
Time in hours, minutes, and seconds in which the next bootstrap message is due from this BSR. |
Next Cand_RP_advertisement in |
Time in hours, minutes, and seconds in which the next candidate rendezvous-point advertisement will be sent. |
RP |
List of IP addresses of rendezvous points. |
Group acl |
Standard IP access list number that defines the group prefixes that are advertised in association with the rendezvous-point address. This value is configured in the ip pim bsr-candidate command. |
Related Commands
show ip pim interface df
To display information about the designated forwarder interface, use the show ip pim interface df command.
show ip pim vrf vrf-name interface df [rp-addr]
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VRF instance. |
rp-addr |
(Optional) Hostname or IP address of the designated forwarder. |
Command Default
If you do not specify rp-addr, all designated forwarders are displayed.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the information about the DF interface:
Router# show ip pim interface df 10.18.1.31
Interface RP DF Winner Metric Uptime
Vlan70 10.18.1.31 10.70.1.55 0 14:16:24
FastEthernet5/5 10.18.1.31 10.16.1.30 0 14:16:24
FastEthernet5/6 10.18.1.31 10.18.1.31 0 14:16:24
Router#
show ip pim mdt bgp
To display the detailed BGP advertisement of the route distinguisher for the MDT default group, use the show ip pim mdt bgp command.
show ip pim vrf vrf-name mdt bgp
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VRF instance. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the detailed BGP advertisement of the route distinguisher for the MDT default group:
Router# show ip pim mdt bgp
MDT-default group 232.2.1.4
rid:1.1.1.1 next_hop:1.1.1.1
Table 2-63 describes the fields shown in the display.
show ip pim mdt history
To display the information on data MDTs that have been reused, use the show ip pim mdt history command.
show ip pim vrf vrf-name mdt history interval minutes
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The show ip pim mdt history command displays the data MDTs that have been reused during the past configured interval.
Examples
This example shows how to display the information on data MDTs that have been reused:
Router# show ip pim vrf blue mdt history interval 20
MDT-data send history for VRF - blue for the past 20 minutes
MDT-data group Number of reuse
10.9.9.8 3
10.9.9.9 2
Table 2-64 describes the fields shown in the display.
show ip pim mdt receive
To display the data MDT advertisements that are received by a specified router, use the show ip pim mdt receive command.
show ip pim vrf vrf-name mdt receive [detail]
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VRF instance. |
detail |
(Optional) Provides a detailed description of the data MDT advertisements that are received. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
When a router wants to switch over from the default MDT to a data MDT, it advertises the VRF source, the group pair, and the global multicast address over which the traffic will be sent. If the remote router wants to receive this data, then the remote router joins this global address multicast group.
Examples
This example shows how to display the data MDT advertisements that are received by a specified router:
Router# show ip pim vrf vpn8 mdt receive detail
Joined MDT-data groups for VRF:vpn8
group:232.2.8.0 source:10.0.0.100 ref_count:13
(10.101.8.10, 225.1.8.1), 1d13h/00:03:28/00:02:26, OIF count:1, flags:TY
(10.102.8.10, 225.1.8.1), 1d13h/00:03:28/00:02:27, OIF count:1, flags:TY
Table 2-65 describes the fields shown in the display.
show ip pim mdt send
To display the data MDT advertisements that a specified router has made, use the show ip pim mdt send command.
show ip pim vrf vrf-name mdt send
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VRF instance. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
Use this command to show the data MDT advertisements that a specified router has made.
Examples
This example shows how to display the data MDT advertisements that a specified router has made:
Router# show ip pim mdt send
MDT-data send list for VRF:vpn8
(source, group) MDT-data group ref_count
(10.100.8.10, 225.1.8.1) 232.2.8.0 1
(10.100.8.10, 225.1.8.2) 232.2.8.1 1
(10.100.8.10, 225.1.8.3) 232.2.8.2 1
(10.100.8.10, 225.1.8.4) 232.2.8.3 1
(10.100.8.10, 225.1.8.5) 232.2.8.4 1
(10.100.8.10, 225.1.8.6) 232.2.8.5 1
(10.100.8.10, 225.1.8.7) 232.2.8.6 1
(10.100.8.10, 225.1.8.8) 232.2.8.7 1
(10.100.8.10, 225.1.8.9) 232.2.8.8 1
(10.100.8.10, 225.1.8.10) 232.2.8.9 1
Table 2-66 describes the fields shown in the display.
show ip pim neighbor
To display the list that the PIM neighbors discovered, use the show ip pim neighbor command.
show ip pim vrf vrf-name neighbor [interface-type interface-number]
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VRF instance. |
interface-type |
(Optional) Interface type. |
interface-number |
Interface number. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
Use this command to determine which routers on the LAN are configured for PIM.
Examples
This example shows how to display the list that the PIM neighbors discovered:
Router# show ip pim neighbor
PIM Neighbor Table
Neighbor Address Interface Uptime Expires Mode
192.168.37.2 Ethernet0 17:38:16 0:01:25 Dense
192.168.37.33 Ethernet0 17:33:20 0:01:05 Dense (DR)
192.168.36.131 Ethernet1 17:33:20 0:01:08 Dense (DR)
192.168.36.130 Ethernet1 18:56:06 0:01:04 Dense
10.1.22.9 Tunnel0 19:14:59 0:01:09 Dense
Table 2-67 describes the fields shown in the display.
Related Commands
show ip pim rp-hash
To display which rendezvous point is being selected for a specified group, use the show ip pim rp-hash command.
show ip pim vrf vrf-name rp-hash {group-address | group-name}
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
This command displays which rendezvous point was selected for the group specified. It also shows whether this rendezvous point was selected by Auto-RP or the PIM Version 2 bootstrap mechanism.
Examples
This example shows how to display which rendezvous point is being selected for a specified group:
Router# show ip pim rp-hash 239.1.1.1
RP 172.16.24.12 (mt1-47a.cisco.com), v2
Info source: 172.16.24.12 (mt1-47a.cisco.com), via bootstrap
Uptime: 05:15:33, expires: 00:02:01
Table 2-68 describes the fields shown in the display.
show ip pim rp mapping
To display the mappings for the PIM group to the active rendezvous points, use the show ip pim rp mapping command.
show ip pim vrf vrf-name rp mapping [rp-address]
Syntax Description
vrf vrf-name |
Specifies the name that is assigned to the multicast VRF instance. |
rp-address |
(Optional) Rendezvous-point IP address. |
Command Default
If you do not specify an rp-address, the mappings for all the active rendezvous points are displayed.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the mappings for the PIM group to the active rendezvous points:
Router# show ip pim rp mapping
PIM Group-to-RP Mappings
This system is an RP-mapping agent
Group(s) 224.1.0.0/16
RP 6.6.6.6 (?), v2v1
Info source: 6.6.6.6 (?), elected via Auto-RP ---> learned via Auto-RP
and the elected RP.
Uptime: 22:36:49, expires: 00:02:04
Group(s) 225.2.2.0/24
RP 9.9.9.9 (?), v2v1, bidir
Info source: 9.9.9.9 (?), elected via Auto-RP
Uptime: 22:36:20, expires: 00:02:37
Group(s) 226.2.2.0/24
RP 2.2.2.2 (?), v2v1, bidir
Info source: 2.2.2.2 (?), elected via Auto-RP
Uptime: 22:36:24, expires: 00:02:29
Group(s) 227.2.2.0/24
RP 9.9.9.9 (?), v2v1, bidir
Info source: 9.9.9.9 (?), elected via Auto-RP
Uptime: 22:36:21, expires: 00:02:35
Router#
Table 2-69 describes the fields that are shown in the example.
show ip pim snooping
To display the information about IP PIM snooping, use the show ip pim snooping command.
show ip pim snooping
show ip pim snooping vlan vlan-id [neighbor | mac-group | statistics | mroute [{src-ip | group-ip}]]
Syntax Description
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the information about the global status:
Router# show ip pim snooping
Global runtime mode: Enabled
Global admin mode : Enabled
Number of user enabled VLANs: 1
User enabled VLANs: 10
Router#
This example shows how to display the information about a specific VLAN:
Router# show ip pim snooping vlan 10
3 neighbors (0 DR priority incapable, 0 Bi-dir incapable)
6 mroutes, 3 mac entries
DR is 10.10.10.4
RP DF Set
Router#
This example shows how to display the information about the neighbor database for a specific VLAN:
Router# show ip pim snooping vlan 10 neighbor
IP Address Mac address Port Uptime/Expires Flags
10.10.10.2 000a.f330.344a 3/13 00:09:57/00:01:22
10.10.10.1 000a.f330.334a 3/12 00:09:44/00:01:21
10.10.10.4 000a.f330.3c00 15/01 00:09:57/00:01:22 DR
Number of Neighbors = 3
Router#
This example shows how to display the information about the GDA database for a specific VLAN in Layer 2:
Router# show ip pim snooping vlan 10 mac-group
Mac address Group address Uptime/Expires Outgoing Ports
0100.5e01.6465 224.1.100.101 00:20:26/00:02:43 3/12 3/13 15/1
0100.5e01.6464 224.1.100.100 00:20:28/00:02:41 3/12 3/13 15/1
0100.5e00.0128 224.0.1.40 00:20:27/00:02:47 3/12 3/13 15/1
Number of mac-groups = 3
Router#
This example shows how to display the detailed statistics for a specific VLAN:
Router# show ip pim snooping vlan 10 statistics
PIMv2 statistics for vlan 10:
Hello : 811
Join/Prunes : 1332
RP DF Election : 0
Asserts : 133
Other types : 0
Hello option holdtime [1] : 811
Hello option Generation ID[20] : 544
Hello option DR priority[19] : 544
Hello option Bi-dir capable[22] : 0
Hello option Fast Hold[65005] : 0
Hello option Lan Prune Delay[2] : 0
Hello option Tag switching [17] : 0
Hello option PIM-DM State Refresh[21] : 544
Hello option Deprecated Cisco DR priority[18] : 0
Error - Hello length too short : 0
Error - Hello hold option missing : 0
Error - Hello option length : 0
Error - Hello option unknown : 0
Error - Join/Prune Address Family : 0
Error - Join/Prune Parser malloc failure : 0
Error - Join/Prune Unknown up/down neighbor : 0
Error - Join/Prune Malformed packet discards : 0
Error - RPDF election Address Family : 0
Error - RPDF Unknown up/down neighbor : 0
Error - Generic packet input error : 0
Router#
This example shows how to display the information about the mroute database for all mrouters in a specific VLAN:
Router# show ip pim snooping vlan 10 mroute
Number of Mroutes = 6
Flags: J/P - (*,G) Join/Prune, j/p - (S,G) Join/Prune
SGR-P - (S,G,R) Prune
(*, 224.1.100.101), 00:16:14/00:02:58
10.10.10.1->10.10.10.2, 00:16:14/00:02:58, J
Downstream ports: 3/12
Upstream ports: 3/13
Outgoing ports: 3/12 3/13
(*, 224.1.100.100), 00:16:16/00:02:56
10.10.10.1->10.10.10.2, 00:16:16/00:02:56, J
Downstream ports: 3/12
Upstream ports: 3/13
Outgoing ports: 3/12 3/13
(10.10.10.2, 224.0.1.40), 00:16:10/00:03:03
10.10.10.1->10.10.10.2, 00:16:10/00:03:03, SGR-P
Downstream ports:
Upstream ports: 3/13
Outgoing ports: 3/13
(*, 224.0.1.40), 00:16:16/00:03:02
10.10.10.1->10.10.10.2, 00:16:16/00:03:02, J
Downstream ports: 3/12
Upstream ports: 3/13
Outgoing ports: 3/12 3/13
(*, 224.10.10.10), 00:02:23/00:01:06
Downstream ports:
Upstream ports:
Outgoing ports: 3/12 3/13
(123.123.123.123, 224.10.10.10), 00:02:23/00:01:06
10.10.10.1->10.10.10.2, 00:02:23/00:01:06, j
Downstream ports: 3/12
Upstream ports: 3/13
Outgoing ports: 3/12 3/13
Router#
This example shows how to display the information about the PIM mroute for a specific source address:
Router# show ip pim snooping vlan 10 mroute 224.1.100.100
(*, 224.1.100.100), 00:16:36/00:02:36
10.10.10.1->10.10.10.2, 00:16:36/00:02:36, J
Downstream ports: 3/12
Upstream ports: 3/13
Outgoing ports: 3/12 3/13
Router#
This example shows how to display the information about the PIM mroute for a specific source and group address:
Router# show ip pim snooping vlan 10 mroute 123.123.123.123 224.10.10.10
(123.123.123.123, 224.10.10.10), 00:03:04/00:00:25
10.10.10.1->10.10.10.2, 00:03:04/00:00:25, j
Downstream ports: 3/12
Upstream ports: 3/13
Outgoing ports: 3/12 3/13
Router#
Related Commands
|
|
|
|---|---|
Enables PIM snooping globally. |
|
Enables PIM snooping on an interface. |
show ip rpf events
To display the triggered RPF statistics, use the show ip rpf events command.
show ip rpf [vrf vrf-name] events
Syntax Description
vrf vrf-name |
(Optional) Specifies the name that is assigned to the multicast VPN routing and forwarding (VRF) instance. |
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the triggered RPF statistics:
Router# show ip rpf events
Last 15 triggered multicast RPF check events
RPF backoff delay: 500 msec
RPF maximum delay: 5 sec
DATE/TIME BACKOFF PROTOCOL EVENT RPF CHANGES
Jan 1 00:00:55.643 500 msec EIGRP Route UP 0
Jan 1 00:00:07.283 1000 sec Connected Route UP 0
Jan 1 00:00:06.283 500 msec Connected Route UP 0
Router#
Related Commands
|
|
|
|---|---|
Sets the PIM-backoff interval. |
|
Sets the RPF consistency-check interval. |
show ip wccp
To display the WCCP statistics, use the show ip wccp command.
show ip wccp [{service-number | web-cache} [detail | view]]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
Use the show ip wccp service-number command to provide the "Total Packets Redirected" count. The "Total Packets Redirected" count is the number of flows, or sessions, that are redirected.
Use the show ip wccp service-number detail command to provide the "Packets Redirected" count. The "Packets Redirected" count is the number of flows, or sessions, that are redirected.
Use the show ip wccp web-cache detail command to provide an indication of how many flows, rather than packets, are using Layer 2 redirection.
For cache-engine clusters using Cisco cache engines, the reverse proxy service-number is indicated by a value of 99.
Use the clear ip wccp command to reset the counter for the "Packets Redirected" information.
For additional information on the IP WCCP commands, refer to the "Configuring Web Cache Services Using WCCP" section in the Cisco IOS Configuration Fundamentals Configuration Guide.
Examples
This example shows how to display the connected cache engine using Layer 2 redirection:
Router# show ip wccp web-cache detail
WCCP Cache-Engine information:
IP Address: 10.11.1.1
Protocol Version: 2.0
State: Usable
Redirection: L2
Initial Hash Info: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Assigned Hash Info: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Hash Allotment: 256 (100.00%)
Packets Redirected: 10273
Connect Time: 17:05:44
Table 2-70 describes the fields that are shown in the example.
Related Commands
show ipv6 mfib
To display the forwarding entries and interfaces in the IPv6 MFIB, use the show ipv6 mfib command.
show ipv6 mfib [{group-ip-addr/prefix-length | group-name | group-address [source-name | source-address]} | {active kbps} | count | interface | status | summary | verbose]
show ipv6 mfib [link-local [active [kbps] | count | verbose]]
Syntax Description
Command Default
prefix-length is 128.
Command Modes
User EXEC (>)
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
Use the show ipv6 mfib command to display MFIB entries, forwarding interfaces, and their traffic statistics. This command can be enabled on virtual IP (VIP) if the router is operating in distributed mode.
Use the show ipv6 mfib active command to display MFIB entries actively used to forward packets. In many cases, it is useful to provide the optional kbps argument to display the set of entries that are forwarding an amount of traffic larger or equal to the amount set by the kbps argument.
Use the show ipv6 mfib count command to display the average packet size and data rate in kilobits per seconds.
The prefix-length is the length of the IPv6 prefix. A decimal value that indicates how many of the high-order contiguous bits of the address comprise the prefix (the network portion of the address). A slash mark must precede the decimal value.
A forwarding entry in the MFIB has flags that determine the default forwarding and signaling behavior to use for packets matching the entry. The entry also has per-interface flags that further specify the forwarding behavior for packets received or forwarded on specific interfaces. Table 2-71 describes the MFIB forwarding entries and interface flags.
Examples
This example shows how to display information for a specific group IPv6 address:
Router# show ipv6 mfib ff35::1:1
IP Multicast Forwarding Information Base
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
AR - Activity Required, D - Drop
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
Interface Flags: A - Accept, F - Forward, NS - Negate Signalling
IC - Internal Copy, NP - Not platform switched
SP - Signal Present
Interface Counts: Distributed FS Pkt Count/FS Pkt Count/PS Pkt Count
(1600::2,FF35::1:1) Flags:
RP Forwarding: 7188/100/48/37, Other: 203619/203619/0
LC Forwarding: 0/0/0/0, Other: 0/0/0
Vlan25 Flags: A
Vlan11 Flags: F NS
Pkts: 0/7188/0
Table 2-72 describes the fields shown in the display.
|
|
|
|---|---|
Entry flags |
Information about the entry. |
Forwarding Counts |
Statistics on the packets that are received and forwarded to at least one interface. |
Pkt Count/ |
Total number of packets received and forwarded since the creation of the multicast forwarding state to which this counter applies. |
Pkts per second/ |
Number of packets received and forwarded per second. |
Avg Pkt Size/ |
Total number of bytes divided by the total number of packets for this multicast forwarding state. There is no direct display for the total number of bytes. You can calculate the total number of bytes by multiplying the average packet size by the packet count. |
Kbits per second |
Bytes per second divided by packets per second, and divided by 1000. |
Other counts: |
Statistics on the received packets. These counters include statistics about the packets received and forwarded and packets received but not forwarded. |
Interface Flags: |
Information about the interface. See Table 2-71 for further information on interface flags. |
Interface Counts: |
Interface statistics. |
This example shows forwarding entries and interfaces in the MFIB with a group address of FF03:1::1 and a source address of 5002:1::2 specified:
Router# show ipv6 mfib FF03:1::1 5002:1::2
IP Multicast Forwarding Information Base
Entry Flags:C - Directly Connected, S - Signal, IA - Inherit A flag,
AR - Activity Required, D - Drop
Forwarding Counts:Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts:Total/RPF failed/Other drops
Interface Flags:A - Accept, F - Forward, NS - Negate Signalling
IC - Internal Copy, NP - Not platform switched
SP - Signal Present
Interface Counts:FS Pkt Count/PS Pkt Count
(5002:1::2,FF03:1::1) Flags:
Forwarding:71505/0/50/0, Other:42/0/42
GigabitEthernet5/0 Flags:A
GigabitEthernet5/0.19 Flags:F NS
Pkts:239/24
GigabitEthernet5/0.20 Flags:F NS
Pkts:239/24
.
.
.
GigabitEthernet5/0.16 Flags:F NS
Pkts:71628/24
This example shows forwarding entries and interfaces in the MFIB with a group address of FF03:1::1 and a default prefix of 128:
Router# show ipv6 mfib FF03:1::1/128
IP Multicast Forwarding Information Base
Entry Flags:C - Directly Connected, S - Signal, IA - Inherit A flag,
AR - Activity Required, D - Drop
Forwarding Counts:Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts:Total/RPF failed/Other drops
Interface Flags:A - Accept, F - Forward, NS - Negate Signalling
IC - Internal Copy, NP - Not platform switched
SP - Signal Present
Interface Counts:FS Pkt Count/PS Pkt Count
(*,FF03:1::1) Flags:C
Forwarding:0/0/0/0, Other:0/0/0
Tunnel1 Flags:A NS
GigabitEthernet5/0.25 Flags:F NS
Pkts:0/0
.
.
.
GigabitEthernet5/0.16 Flags:F NS
Pkts:0/0
This example displays statistics on the rate at which active IP multicast sources are sending information. The router is switching traffic from 2001::1:1:200 to FF05::1:
Router# show ipv6 mfib active
Active IPv6 Multicast Sources - sending >= 4 kbps
Group: FF05::1
Source: 2001::1:1:200
Rate: 20 pps/16 kbps(1sec), 0 kbps(last 128 sec)
Table 2-73 describes the fields shown in the display.
This example displays statistics from the MFIB about the group and source. The router is switching traffic from 2001::1:1:200 to FF05::1:
Router# show ipv6 mfib count
IP Multicast Statistics
54 routes, 7 groups, 0.14 average sources per group
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kilobits per second
Other counts: Total/RPF failed/Other drops(OIF-null, rate-limit etc)
Group: FF00::/8
RP-tree: Forwarding: 0/0/0/0, Other: 0/0/0
Group: FF00::/15
RP-tree: Forwarding: 0/0/0/0, Other: 0/0/0
Group: FF05::1
RP-tree: Forwarding: 2/0/100/0, Other: 0/0/0
Source: 10::1:1:200, Forwarding: 367/10/100/7, Other: 0/0/0
Tot. shown: Source count: 1, pkt count: 369
Group: FF10::/15
RP-tree: Forwarding: 0/0/0/0, Other: 0/0/0
Group: FF20::/15
RP-tree: Forwarding: 0/0/0/0, Other: 0/0/0
Table 2-74 describes the fields shown in the display.
This example shows forwarding entries and interfaces in the MFIB and additional information such as the MAC encapsulation header and platform-specific information:
Router# show ipv6 mfib ff33::1:1 verbose
IP Multicast Forwarding Information Base
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
AR - Activity Required, K - Keepalive
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
Platform per slot HW-Forwarding Counts: Pkt Count/Byte Count
Platform flags: HF - Forwarding entry,HB - Bridge entry,HD - NonRPF Drop entry,
NP - Not platform switchable,RPL - RPF-ltl linkage,
MCG - Metset change,ERR - S/w Error Flag,RTY - In RetryQ,
LP - L3 pending,MP - Met pending,AP - ACL pending
Interface Flags: A - Accept, F - Forward, NS - Negate Signalling
IC - Internal Copy, NP - Not platform switched
SP - Signal Present
Interface Counts: Distributed FS Pkt Count/FS Pkt Count/PS Pkt Count
(10::2,FF33::1:1) Flags: K
RP Forwarding: 0/0/0/0, Other: 0/0/0
LC Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwd: 0/0/0/0, Other: NA/NA/NA
Slot 6: HW Forwarding: 0/0, Platform Flags: HF RPL
Slot 1: HW Forwarding: 0/0, Platform Flags: HF RPL
Vlan10 Flags: A
Vlan30 Flags: F NS
Pkts: 0/0/0 MAC: 33330001000100D0FFFE180086DD
Router#
Table 2-75 describes the fields shown in the display.
Table 2-76 describes the MFIB platform flags.
show ipv6 mld snooping
To display MLDv2 snooping information, use the show ipv6 mld snooping command.
show ipv6 mld snooping {{explicit-tracking vlan} | {mrouter [vlan vlan]} | {report-suppression vlan vlan} | {statistics vlan vlan}}
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
You can also use the show ip igmp snooping commands to display information about IGMP snooping.
You can enter the show ipv6 mld snooping mrouter command without arguments to display all the multicast router interfaces.
Examples
This example shows how to display explicit tracking information on VLAN 25:
Router# show ipv6 mld snooping explicit-tracking vlan 25
Source/Group Interface Reporter Filter_mode
------------------------------------------------------------------------
10.1.1.1/226.2.2.2 Vl25:1/2 16.27.2.3 INCLUDE
10.2.2.2/226.2.2.2 Vl25:1/2 16.27.2.3 INCLUDE
Router#
This example shows how to display the multicast router interfaces in VLAN 1:
Router# show ipv6 mld snooping mrouter vlan 1
vlan ports
-----+----------------------------------------
1 Gi1/1,Gi2/1,Fa3/48,Router
Router#
This example shows the IGMP snooping statistics information for VLAN 25:
Router# show ipv6 mld snooping statistics interface vlan 25
Snooping staticstics for Vlan25
#channels:2
#hosts :1
Source/Group Interface Reporter Uptime Last-Join Last-Leave
10.1.1.1/226.2.2.2 Gi1/2:Vl25 16.27.2.3 00:01:47 00:00:50 -
10.2.2.2/226.2.2.2 Gi1/2:Vl25 16.27.2.3 00:01:47 00:00:50 -
Router#
Related Commands
|
|
|
|---|---|
Enables MLDv2 snooping globally. |
|
Enables explicit host tracking. |
|
Enables the MLDv2 snooping querier. |
|
Enables report suppression on a VLAN. |
show l2protocol-tunnel
To display the protocols that are tunneled on an interface or on all interfaces, use the show l2protocol-tunnel command.
show l2protocol-tunnel [{interface interface mod/port} | {vlan vlan-id} | summary]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The show l2protocol-tunnel command displays only the ports that have protocol tunneling enabled.
The show l2protocol-tunnel summary command displays the ports that have protocol tunneling enabled, regardless of whether the port is down or currently configured as a trunk.
Examples
This example shows how to display the protocols that are tunneled on all interfaces:
Router# show l2protocol-tunnel
COS for Encapsulated Packets: 5
Drop Threshold for Encapsulated Packets: 3000
Port Protocol Shutdown Drop Encapsulation Decapsulation Drop
Threshold Threshold Counter Counter Counter
------- -------- --------- --------- ------------- ------------- -------------
Fa3/38 cdp ---- 3000 5 0 0
stp ---- 3000 2653 0 0
--- ---- ---- ---- ----
Router#
This example shows how to display a summary of Layer 2-protocol tunnel ports:
Router# show l2protocol-tunnel summary
COS for Encapsulated Packets:5
Drop Threshold for Encapsulated Packets:0
Port Protocol Shutdown Drop Status
Threshold Threshold
(cdp/stp/vtp) (cdp/stp/vtp)
------- ----------- ---------------- ---------------- ----------
Fa9/1 --- stp --- ----/----/---- ----/----/---- down
Fa9/9 cdp stp vtp ----/----/---- ----/----/---- up
Fa9/47 --- --- --- ----/----/---- 1500/1500/1500 down(trunk)
Fa9/48 cdp stp vtp ----/----/---- ----/----/---- down(trunk)
Router>
Related Commands
show l3-mgr
To display the information about the Layer 3 manager, use the show l3-mgr command.
show l3-mgr status
show l3-mgr {interface {{interface interface-number} | {null interface-number} | {port-channel number} | {vlan vlan-id} | status}}
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.
The port-channel number values from 257 to 282 are supported on the CSM and the FWSM only.
Examples
This example shows how to display the status of the Layer 3 manager:
Router# show l3-mgr status
l3_mgr_state: 2
l3_mgr_req_q.count: 0
l3_mgr_req_q.head: 0
l3_mgr_req_q.tail: 0
l3_mgr_max_queue_count: 1060
l3_mgr_shrunk_count: 0
l3_mgr_req_q.ip_inv_count: 303
l3_mgr_req_q.ipx_inv_count: 0
l3_mgr_outpak_count: 18871
l3_mgr_inpak_count: 18871
l3_mgr_max_pending_pak: 4
l3_mgr_pending_pak_count: 0
nde enable statue: 0
current nde addr: 0.0.0.0
Router#
This example shows how to display the information about the Layer 3 manager for a specific interface:
Router# show l3-mgr interface fastethernet 5/40
vlan: 0
ip_enabled: 1
ipx_enabled: 1
bg_state: 0 0 0 0
hsrp_enabled: 0
hsrp_mac: 0000.0000.0000
state: 0
up: 0
Router#
show lacp
To display LACP information, use the show lacp command.
show lacp [channel-group] {counters | internal | neighbors | sys-id}
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
If you do not specify a channel-group, all channel groups are displayed.
The channel-group values from 257 to 282 are supported on the CSM and the FWSM only.
You can enter the optional channel-group to specify a channel group for all keywords, except the sys-id keyword.
Examples
This example shows how to display the LACP statistics for a specific channel group:
Router# show lacp 1 counters
LACPDUs Marker LACPDUs
Port Sent Recv Sent Recv Pkts Err
---------------------------------------------------
Channel group: 1
Fa4/1 8 15 0 0 3 0
Fa4/2 14 18 0 0 3 0
Fa4/3 14 18 0 0 0
Fa4/4 13 18 0 0 0
The output displays the following information:
•The LACPDUs Sent and Recv columns display the LACPDUs that are sent and received on each specific interface.
•The LACPDUs Pkts and Err columns display the marker-protocol packets.
This example shows how to display internal information for the interfaces that belong to a specific channel:
Router# show lacp 1 internal
Flags: S - Device sends PDUs at slow rate. F - Device sends PDUs at fast rate.
A - Device is in Active mode. P - Device is in Passive mode.
Channel group 1
LACPDUs LACP Port Admin Oper Port Port
Port Flags State Interval Priority Key Key Number State
Fa4/1 saC bndl 30s 32768 100 100 0xc1 0x75
Fa4/2 saC bndl 30s 32768 100 100 0xc2 0x75
Fa4/3 saC bndl 30s 32768 100 100 0xc3 0x75
Fa4/4 saC bndl 30s 32768 100 100 0xc4 0x75
Router#
Table 2-77 describes the fields that are shown in the example.
This example shows how to display the information about the LACP neighbors for a specific port channel:
Router# show lacp 1 neighbors
Flags: S - Device sends PDUs at slow rate. F - Device sends PDUs at fast rate.
A - Device is in Active mode. P - Device is in Passive mode.
Channel group 1 neighbors
Partner Partner
Port System ID Port Number Age Flags
Fa4/1 8000,00b0.c23e.d84e 0x81 29s P
Fa4/2 8000,00b0.c23e.d84e 0x82 0s P
Fa4/3 8000,00b0.c23e.d84e 0x83 0s P
Fa4/4 8000,00b0.c23e.d84e 0x84 0s P
Port Admin Oper Port
Priority Key Key State
Fa4/1 32768 200 200 0x81
Fa4/2 32768 200 200 0x81
Fa4/3 32768 200 200 0x81
Fa4/4 32768 200 200 0x81
Router#
If no PDUs have been received, the default administrative information is displayed in braces.
This example shows how to display the LACP system identification:
Router> show lacp sys-id
8000,AC-12-34-56-78-90
The system identification is made up of the system priority and the system MAC address. The first 2 bytes are the system priority, and the last 6 bytes are the globally administered individual MAC address that is associated to the system.
Related Commands
|
|
|
|---|---|
Clears the statistics for all interfaces belonging to a specific channel group. |
|
Sets the priority for the physical interfaces. |
|
Sets the priority of the system. |
show logging ip access-list
To display information about the logging IP access list, use the show logging ip access-list command.
show logging ip access-list {cache | config}
Syntax Description
cache |
Displays information about all the entries in the OAL cache. |
config |
Displays information about the logging IP access-list configuration. |
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
OAL is supported on IPv4 unicast traffic only.
Examples
This example shows how to display all the entries in the OAL cache:
Router# show logging ip access-list cache
Matched flows:
id prot src_ip dst_ip sport dport status count
total lastlog
--------------------------------------------------------------------------------------
1 17 20.2.1.82 21.2.12.2 111 63 Permit 0
3906 2d02h
2 17 20.2.1.82 21.2.12.2 1135 63 Permit 0
3906 2d02h
3 17 20.2.1.82 21.2.12.2 2159 63 Permit 0
3906 2d02h
4 17 20.2.1.82 21.2.12.2 3183 63 Permit 0
3906 2d02h
5 17 20.2.1.82 21.2.12.2 4207 63 Permit 0
3906 2d02h
6 17 20.2.1.82 21.2.12.2 5231 63 Deny 0
3906 2d02h
7 17 20.2.1.82 21.2.12.2 6255 63 Deny 0
3906 2d02h
8 17 20.2.1.82 21.2.12.2 7279 63 Permit 0
3906 2d02h
9 17 20.2.1.82 21.2.12.2 8303 63 Permit 0
3906 2d02h
10 17 20.2.1.82 21.2.12.2 9327 63 Permit 0
3905 2d02h
11 17 20.2.1.82 21.2.12.2 10351 63 Permit 0
3905 2d02h
12 17 20.2.1.82 21.2.12.2 11375 63 Permit 0
3905 2d02h
13 17 20.2.1.82 21.2.12.2 12399 63 Deny 0
3905 2d02h
14 17 20.2.1.82 21.2.12.2 13423 63 Permit 0
3905 2d02h
15 17 20.2.1.82 21.2.12.2 14447 63 Deny 0
3905 2d02h
16 17 20.2.1.82 21.2.12.2 15471 63 Permit 0
3905 2d02h
17 17 20.2.1.82 21.2.12.2 16495 63 Permit 0
3905 2d02h
18 17 20.2.1.82 21.2.12.2 17519 63 Permit 0
3905 2d02h
19 17 20.2.1.82 21.2.12.2 18543 63 Permit 0
3905 2d02h
20 17 20.2.1.82 21.2.12.2 19567 63 Permit 0
3905 2d02h
Number of entries: 20
Number of messages logged: 112
Number of packets logged: 11200
Number of packets received for logging: 11200
Router#
This example shows how to display information about the logging IP access-list configuration:
Router# show logging ip access-list config
Logging ip access-list configuration
Maximum number of cached entries: 8192
Logging rate limiter: 0
Log-update interval: 300
Log-update threshold: 0
Configured on input direction:
Vlan2
Vlan1
Configured on output direction:
Vlan2
Router#
Related Commands
|
|
|
|---|---|
Clears all the entries from the OAL cache and sends them to the syslog. |
|
Configures the OAL parameters. |
|
Enables an OAL-logging cache on an interface that is based on direction. |
show mac-address-table
To display the information about the MAC-address table, use the show mac-address-table command.
show mac-address-table
show mac-address-table {address mac-addr} [all | {interface interface interface-number} | {vlan vlan-id}]
show mac-address-table aging-time [vlan vlan-id]
show mac-address-table count [vlan vlan-id]
show mac-address-table dynamic [{address mac-addr} | {interface interface interface-number} | {vlan vlan-id}]
show mac-address-table {interface interface interface-number}
show mac-address-table limit [vlan vlan-id | {interface interface}]
show mac-address-table multicast [count | {{igmp-snooping | mld-snooping} [count]} | {user [count]} | {vlan vlan-id}]
show mac-address-table notification {mac-move | threshold}
show mac-address-table static [{address mac-addr} | detail | {interface interface interface-number} | {vlan vlan-id}]
show mac-address-table synchronize statistics
show mac-address-table unicast-flood
show mac-address-table vlan vlan-id
Syntax Description
Command Default
This command has no default settings.
Command Modes
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
If you do not specify a module number, the output of the show mac-address-table command displays information about the supervisor engine. To display information about the MAC-address table of the switch processor, you must enter the all keyword.
The mac-addr is a 48-bit MAC address and the valid format is H.H.H.
The interface-number argument designates the module and port number. Valid values for interface-number depend on the specified interface type and the chassis and module that are used. For example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values for the port number are from 1 to 48.
Valid values for mac-group-address are from 1 to 9.
The optional count keyword displays the number of multicast entries.
The optional multicast keyword displays the multicast MAC addresses (groups) in a VLAN or displays all statically installed or IGMP snooping-learned entries in the Layer 2 table.
The information that is displayed in the show mac-address-table unicast-flood command output is as follows:
•Up to 50 flood entries, shared across all the VLANs that are not configured to use the filter mode, can be recorded.
•The output field displays are defined as follows:
–ALERT—Information is updated approximately every 3 seconds.
–SHUTDOWN—Information is updated approximately every 3 seconds.
Note The information displayed on the destination MAC addresses is deleted as soon as the floods stop after the port shuts down.
–Information is updated each time that you install the filter. The information lasts until you remove the filter.
The show mac-address-table protocol {assigned | ip | ipx | other} syntax is not supported on Catalyst 6500 series switches that are configured with a Supervisor Engine 720.
The keyword definitions for the protocol argument are as follows:
•assigned specifies assigned protocol entries.
•ip specifies IP protocol.
•ipx specifies IPX protocols.
•other specifies other protocol entries.
The dynamic entries that are displayed in the Learn field are always set to Yes.
The show mac-address-table limit command output displays the following information:
•The current number of MAC addresses.
•The maximum number of MAC entries that are allowed.
•The percentage of usage.
The show mac-address-table synchronize statistics command output displays the following information:
•Number of messages processed at each time interval.
•Number of active entries sent for synchronization.
•Number of entries updated, created, ignored, or failed.
Examples
Note In a distributed EARL switch, the asterisk (*) indicates a MAC address that is learned on a port that is associated with this EARL.
This example shows how to display the information about the MAC-address table for a specific MAC address (the Catalyst 6500 series switch is configured with a Supervisor Engine 2):
Router# show mac-address-table address 001.6441.60ca
Codes: * - primary entry
vlan mac address type learn qos ports
------+----------------+--------+-----+---+--------------------------
Supervisor:
* --- 0001.6441.60ca static No -- Router
Router#
This example shows how to display MAC-address table information for a specific MAC address (the Catalyst 6500 series switch is configured with a Supervisor Engine 720):
Router# show mac-address-table address 0100.5e00.0128
Legend: * - primary entry
age - seconds since last seen
n/a - not available
vlan mac address type learn age ports
------+----------------+--------+-----+----------+--------------------------
Supervisor:
* 44 0100.5e00.0128 static Yes - Fa6/44,Router
* 1 0100.5e00.0128 static Yes - Router
Module 9:
* 44 0100.5e00.0128 static Yes - Fa6/44,Router
* 1 0100.5e00.0128 static Yes - Router
Router#
This example shows how to display the currently configured aging time for all VLANs:
Router# show mac-address-table aging-time
Vlan Aging Time
---- ----------
*100 300
200 1000
Router#
This example shows how to display the entry count for a specific slot:
Router# show mac-address-table count slot 1
MAC Entries on slot 1 :
Dynamic Address Count: 4
Static Address (User-defined) Count: 25
Total MAC Addresses In Use: 29
Total MAC Addresses Available: 131072
Router#
This example shows how to display all the dynamic MAC-address entries:
Router# show mac-address-table dynamic
Legend: * - primary entry
age - seconds since last seen
n/a - not applicable
vlan mac address type learn age ports
------+----------------+--------+-----+----------+--------------------------
* 10 0010.0000.0000 dynamic Yes n/a Gi4/1
* 3 0010.0000.0000 dynamic Yes 0 Gi4/2
* 1 0002.fcbc.ac64 dynamic Yes 265 Gi8/1
* 1 0009.12e9.adc0 static No - Router
Router#
This example shows how to display the information about the MAC-address table for a specific interface (the Catalyst 6500 series switch is configured with a Supervisor Engine 720):
Router# show mac-address-table interface fastethernet 6/45
Legend: * - primary entry
age - seconds since last seen
n/a - not available
vlan mac address type learn age ports
------+----------------+--------+-----+----------+--------------------------
* 45 00e0.f74c.842d dynamic Yes 5 Fa6/45
Router#
Note A leading asterisk (*) indicates entries from a MAC address that was learned from a packet coming from an outside device to a specific module.
This example shows how to display the MAC-move notification status:
Router# show mac-address-table notification mac-move
MAC Move Notification: Enabled
Router#
This example shows how to display the CAM-table utilization-notification status:
Router# show mac-address-table notification threshold
Status limit Interval
-------------+-----------+-------------
enabled 1 120
Router#
This example shows how to display unicast-flood information:
Router# show mac-address-table unicast-flood
Unicast Flood Protection status: enabled
Configuration:
vlan Kfps action timeout
------+----------+-----------------+----------
2 2 alert none
Mac filters:
No. vlan souce mac addr. installed
on time left (mm:ss)
-----+------+-----------------+------------------------------+------------------
Flood details:
Vlan souce mac addr. destination mac addr.
------+----------------+-------------------------------------------------
2 0000.0000.cafe 0000.0000.bad0, 0000.0000.babe,
0000.0000.bac0
0000.0000.bac2, 0000.0000.bac4,
0000.0000.bac6
0000.0000.bac8
2 0000.0000.caff 0000.0000.bad1, 0000.0000.babf,
0000.0000.bac1
0000.0000.bac3, 0000.0000.bac5,
0000.0000.bac7
0000.0000.bac9
Router#
This example shows how to display all the static MAC-address entries (this Catalyst 6500 series switch is configured with a Supervisor Engine 2):
Router# show mac-address-table static
Codes: * - primary entry
vlan mac address type learn qos ports
------+----------------+--------+-----+---+--------------------------
* --- 0001.6441.60ca static No -- Router
Router#
This example shows how to display the information about the MAC-address table for a specific VLAN:
Router# show mac-address-table vlan 100
vlan mac address type protocol qos ports
-----+---------------+--------+---------+---+--------------------------------
100 0050.3e8d.6400 static assigned -- Router
100 0050.7312.0cff dynamic ip -- Fa5/9
100 0080.1c93.8040 dynamic ip -- Fa5/9
100 0050.3e8d.6400 static ipx -- Router
100 0050.3e8d.6400 static other -- Router
100 0100.0cdd.dddd static other -- Fa5/9,Router,Switch
100 00d0.5870.a4ff dynamic ip -- Fa5/9
100 00e0.4fac.b400 dynamic ip -- Fa5/9
100 0100.5e00.0001 static ip -- Fa5/9,Switch
100 0050.3e8d.6400 static ip -- Router
Router#
This example shows how to display the information about the MAC-address table for MLDv2 snooping:
Router# show mac-address-table multicast mld-snooping
vlan mac address type learn qos ports
-----+---------------+--------+-----+---+--------------------------------
--- 3333.0000.0001 static Yes - Switch,Stby-Switch
--- 3333.0000.000d static Yes - Fa2/1,Fa4/1,Router,Switch
--- 3333.0000.0016 static Yes - Switch,Stby-Switch
Router#
Related Commands
show mac-address-table learning
To display the MAC-address learning state, use the show mac-address-table learning command.
show mac-address-table learning [{vlan vlan-id} | {interface interface slot/port}] [module num]
Syntax Description
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The module num keyword and argument can be used to specify supervisor engines only.
The interface interface slot/port keyword and arguments can be used on routed interfaces only. The interface interface slot/port keyword and arguments cannot be used to configure learning on switch-port interfaces.
If you specify the vlan vlan-id, the state of the MAC-address learning of the specified VLAN, including router interfaces, on all modules, is displayed.
If you specify the vlan vlan-id and the module num, the state of the MAC-address learning of a specified VLAN on a specified module is displayed.
If you specify the interface interface slot/port keyword and arguments, the state of the MAC-address learning of the specified interface on all modules is displayed.
If you specify the interface interface slot/port keyword and arguments, the state of the MAC-address learning of the specified interface on the specified module is displayed.
If you enter the show mac-address-table learning command with no arguments or keywords, the status of MAC learning on all the existing VLANs on all the supervisor engines configured on a Catalyst 6500 series switch is displayed.
Examples
This example shows how to display the MAC-address learning status on all the existing VLANs on all the supervisor engines:
Router# show mac-address-table learning
VLAN/Interface Mod1 Mod4 Mod7
-------------------- ---------------------
1 yes yes yes
100 yes yes yes
150 yes yes yes
200 yes yes yes
250 yes yes yes
1006 no no no
1007 no no no
1008 no no no
1009 no no no
1010 no no no
1011 no no no
1012 no no no
1013 no no no
1014 no no no
GigabitEthernet6/1 no no no
GigabitEthernet6/2 no no no
GigabitEthernet6/4 no no no
FastEthernet3/4 no no no
FastEthernet3/5 no no no
GigabitEthernet4/1 no no no
GigabitEthernet4/2 no no no
GigabitEthernet7/1 no no no
GigabitEthernet7/2 no no no
Router#
Table 2-78 describes the fields that are shown in the example.
|
|
|
|---|---|
VLAN/Interface1 |
VLAN ID or interface type, module, and port number. |
Mod# |
Module number of a supervisor engine. |
yes |
MAC-address learning is enabled. |
no |
MAC-address learning is disabled. |
1 The interfaces displayed are routed interfaces that have internal VLANs assigned to them. |
This example shows how to display the status of MAC-address learning on all the existing VLANs on a single supervisor engine:
Router# show mac-address-table learning module 4
VLAN/Interface Mod4
-------------------- -----
1 yes
100 yes
150 yes
200 yes
250 yes
1006 no
1007 no
1008 no
1009 no
1010 no
1011 no
1012 no
1013 no
1014 no
GigabitEthernet6/1 no
GigabitEthernet6/2 no
GigabitEthernet6/4 no
FastEthernet3/4 no
FastEthernet3/5 no
GigabitEthernet4/1 no
GigabitEthernet4/2 no
GigabitEthernet7/1 no
GigabitEthernet7/2 no
Router#
This example shows how to display the status of MAC-address learning for a specific VLAN on all the supervisor engines:
Router# show mac-address-table learning vlan 100
VLAN Mod1 Mod4 Mod7
---- ---------------------
100 no no yes
Router
This example shows how to display the status of MAC-address learning for a specific VLAN on a specific supervisor engine:
Router# show mac-address-table learning vlan 100 module 7
VLAN Mod7
---- -----
100 yes
Router
This example shows how to display the status of MAC-address learning for a specific supervisor engine:
Router# show mac-address-table learning interface FastEthernet 3/4
Interface Mod1 Mod4 Mod7
--------- ---------------------
Fa3/4 no yes no
Router
This example shows how to display the status of MAC-address learning for a specific interface on a specific specific supervisor engine:
Router# show mac-address-table learning interface FastEthernet 3/4 module 1
Interface Mod1
--------- -----
Fa3/4 no
Router
Related Commands
|
|
|
|---|---|
Enables MAC-address learning. |
show memory dead
To display statistics of memory allocated by processes that are now terminated, use the show memory dead command.
show memory dead [totals]
Syntax Description
totals |
(Optional) Displays memory totals for processes that have been terminated. |
Command Default
This command has no default settings.
Command Modes
User EXEC (>)
Privileged EXEC (#)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Usage Guidelines
The show memory dead command displays information about processes that have been terminated. Terminated processes accounts for memory allocated under another process.
Examples
This example shows the sample output from the show memory dead command:
Router# show memory dead
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
I/O 600000 2097152 461024 1636128 1635224 1635960
Processor memory
Address Bytes Prev. Next Ref PrevF NextF Alloc PC What
1D8310 60 1D82C8 1D8378 1 3281FFE Router Init
2CA964 36 2CA914 2CA9B4 1 3281FFE Router Init
2CAA04 112 2CA9B4 2CAAA0 1 3A42144 OSPF Stub LSA RBTree
2CAAA0 68 2CAA04 2CAB10 1 3A420D4 Router Init
2ED714 52 2ED668 2ED774 1 3381C84 Router Init
2F12AC 44 2F124C 2F1304 1 3A50234 Router Init
2F1304 24 2F12AC 2F1348 1 3A420D4 Router Init
2F1348 68 2F1304 2F13B8 1 3381C84 Router Init
300C28 340 300A14 300DA8 1 3381B42 Router Init
Table 2-79 describes the significant fields shown in the display.
show mls asic
To display the ASIC version, use the show mls asic command.
show mls asic
Syntax Description
This command has no keywords or arguments.
Command Default
This command has no default settings.
Command Modes
EXEC (>)
Command History
|
|
|
|---|---|
12.2(18)ZY |
Support for this command was introduced. |
Examples
This example shows how to display the ASIC versions:
Router# show mls asic
Earl in Module 2
Tycho - ver:1 Cisco-id:1C8 Vendor-id:49
Router#
Feedback