Configuring T3 or E3 Interfaces

This section provides the information about how to configure a T3 or E3 interface. The T3 or E3 interface can be configured as clear channel mode or channelized mode.

Configuring the Mode

To enable the mode on the T3/E3 interface module, follow these steps:

 
enable
configure terminal
controller mediatype 0/4/0
mode t3
exit

To disable the mode use the no mode command.

Configuring the Controller

Configuring the Controller - Clear Channel T3 or E3 Interfaces

Before You Begin

When the clear channel T3 or E3 interface is used for the first time, the running configuration does not show the T3 or E3 controller. You can use the show platform command to check whether the chassis recognizes the T3 or E3 port and initializes the card correctly. After the port is configured for the slot, the respective controller appears in the running configuration and you can configure the clear channel T3 or E3 interface.

Perform this task to configure clear channel controller as T3.

 
enable
configure terminal
controller t3 0/4/40
no channelized
clock source line
no shut
exit

Note


By default, the T3 controller is in C-Bit framing mode. To configure CEM, the framing mode must be set to unframed.


Perform this task to configure clear channel controller as E3.

 
enable
configure terminal
controller e3 0/4/40
clock source line
no shut
exit

Configuring the Controller - Channelized T3 or E3 Interfaces

Before You Begin

When the channelized T3 or E3 interface is used for the first time, the running configuration does not show the T3 or E3 controller. You can use the show platform command to check if the chassis recognizes the T3 or E3 port and initializes the card properly. After the port is configured for the slot, the respective controller appears in the running configuration and you can configure the channelized T3 or E3 interface.

Perform this task to configure channelized controller as T3.

 
enable
configure terminal
controller t3 0/4/46
channelized
clock source line
no shut
exit

Note


The channelized mode is the default mode for T3 interface.


Perform this task to configure channelized controller as E3.

 
enable
configure terminal
controller e3 0/4/46
channelized mode  e1
framing  g751
exit

Note


The clear channel mode is the default mode for E3 interface.


Table 1. Feature History

Feature Name

Release Information

Description

Channelize the T3 interface into E1 lines

Cisco IOS XE Bengaluru 17.6.2

Support for the T3 interface to be channelized into 21 E1 lines.

Starting with Cisco IOS XE Bengaluru 17.6.2, T3 interface can be channelized to 21 E1 lines.

To channelize the T3 interface into E1 lines, use the following commands:

 
enable
configure terminal
controller MediaType0/1/1
mode t3
controller t30/1/1
channelized mode  e1
framing  c-bit
exit

SATOP

Configuring SAToP - Clear Channel T3 or E3 Interfaces

Before You Begin

Before Structure-Agnostic TDM over Packet (SAToP) is configured, the controller of clear channel T3 interface must be configured.

 
enable 
configure terminal
controller t3 0/4/40
no channelized
cem-group 0 unframed 
interface CEM 0/4/40
cem 0 
xconnect  10.10.2.2 204 encapsulation mpls
exit

Before You Begin

Before SAToP is configured, the controller of clear channel E3 interface must be configured.

 
enable 
configure terminal
controller e3  0/4/40
no channelized 
cem-group 0 unframed 
interface CEM 0/4/40
cem  0 
xconnect  10.10.2.2 204 encapsulation mpls
exit

Verifiying the configuration


Note


The no channelize is displayed in show running-configuration when cem-group 0 unframed is configured.


Router(config-controller)# show run 
controller MediaType 0/4/40
 mode e3
controller 0/4/40
 threshold sd-ber 6
 threshold sf-ber 3
 no channelized
 framing g751
 cablelength short
  cem-group 0 framed
controller MediaType 0/4/40
interface CEM8/1/10/4/40
 no ip address
 cem 0
 !

Configuring SAToP - Channelized T3 Interfaces

Before You Begin

Before SAToP is configured, the controller of channelized T3 interface must be configured.

 
enable 
configure terminal
controller t3 0/4/12
channelized
t1 1 cem-group 0 unframed 
interface CEM 0/4/12
cem 0 
xconnect 10.10.2.2 204 encapsulation mpls
exit

Configuring SAToP - Channelized E3 Interfaces

Before You Begin

Before SAToP is configured, the controller of channelized E3 interfaces must be configured.

 
enable 
configure terminal
controller e3 0/4/46
channelized
e1 1 cem-group 0 unframed 
interface CEM 0/4/46
cem 0 
xconnect 10.10.2.2 204 encapsulation mpls
exit

Configuring Framed SAToP - Channelized T3 Interfaces


Note


Framing type should be maintained same in all routers end to end.


To configure the controller of channelized T3 interface for framed SAToP:
 
enable 
configure terminal
controller t3 0/4/46
channelized mode
framing c-bit
t1 1 cem-group 0 framed 
interface CEM 0/4/46
cem 0 
xconnect 10.10.2.2 204 encapsulation mpls
exit

Configuring Framed SAToP - Channelized E3 Interfaces

To configure the controller of channelized E3 interfaces for Framed SAToP:
 
enable 
configure terminal
controller e3 0/4/46
channelized mode e1
framing g751
e1 1 cem-group 0 framed 
interface CEM 0/4/46
cem 0 
xconnect 10.10.2.2 204 encapsulation mpls
exit

CESoPN

Configuring CESoPSN - Channelized T3 or E3 Interfaces

Before You Begin

Create CEM group for channelized T3 interface, use the following commands:

 
enable 
configure terminal
controller MediaType 0/5/1
 mode t3
channelized   
controller T3 0/5/1
 framing c-bit
 cablelength short
 t1 1 cem-group 1 timeslots 10
exit

Create CEM group for channelized E3 interface, use the following commands:

 
enable 
configure terminal
controller MediaType 0/5/1
 mode e3
channelized mode e1
controller e3 0/14/0
channelized
 cablelength short
 e1 1 cem-group 0 timeslots 10 
exit
Configure xconnect:

int cem 0/14/0                           
cem 0                                    
xconnect 10.1.1.1 9999 encapsulation mpls 
Verify the xconnect status:

sh xconnect all  | i 9999
UP pri   ac CE0/14/0:0(CESoPSN Basic)    UP mpls 10.1.1.1:9999                 UP

Verifying CESoPSN Configurations - Channelized E3 Interface

This section includes show commands for CESoPSN:
Router# show controllers  e3 0/14/2
E3 0/14/2 is up.
  Hardware is -48T3E3-CE
  Applique type is Channelized E3
  No alarms detected.
  Framing is E3 G751, Line Code is HDB3, Cablelength Short less than 225ft
  BER thresholds:  SF = 10e-10  SD = 10e-10
  Clock Source is internal, National Bit 0
  Equipment customer loopback
  Data in current interval (240 seconds elapsed):                              
   Near End                                                                    
     0 Line Code Violations, 0 P-bit Coding Violations                         
     0 C-bit Coding Violations, 0 P-bit Err Secs                               
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs                    
     0 Unavailable Secs, 0 Line Errored Secs                                   
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs                       
     0 Severely Errored Line Secs, 0 Path Failures                             
     0 AIS Defect Secs, 0 LOS Defect Secs                                      
   Far End                                                                     
     0 Errored Secs, 0 Severely Errored Secs                                   
     0 C-bit Unavailable Secs, 0 Path Failures                                 
     0 Code Violations, 0 Service Affecting Secs                               
  Data in Interval 1:                                                          
   Near End                                                                    
     0 Line Code Violations, 0 P-bit Coding Violations                         
     0 C-bit Coding Violations, 0 P-bit Err Secs                               
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs                    
     20 Unavailable Secs, 20 Line Errored Secs                                 
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs                       
     20 Severely Errored Line Secs, 1 Path Failures                            
     0 AIS Defect Secs, 20 LOS Defect Secs                                     
   Far End                                                                     
     0 Errored Secs, 0 Severely Errored Secs                                   
     0 C-bit Unavailable Secs, 0 Path Failures                                 
     0 Code Violations, 0 Service Affecting Secs                               
  Total Data (last 1 15 minute intervals):                                     
   Near End                                                                    
     0 Line Code Violations, 0 P-bit Coding Violations,                        
     0 C-bit Coding Violations, 0 P-bit Err Secs,                              
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,                   
     20 Unavailable Secs, 20 Line Errored Secs,                                
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs                       
     20 Severely Errored Line Secs, 1 path failures                            
     0 AIS Defect Secs, 20 LOS Defect Secs                                     
   Far End                                                                     
     0 Errored Secs, 0 Severely Errored Secs                                   
     0 C-bit Unavailable Secs, 0 Path Failures                                 
     0 Code Violations, 0 Service Affecting Secs

E1 1 is up
  timeslots: 
  FDL per AT&T 54016 spec.
  No alarms detected.     
  Framing is crc4, Clock Source is Internal, National bits are 0x1F.
  Data in current interval (250 seconds elapsed):
   Near End                                      
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs       
     0 Unavailable Secs, 0 Stuffed Secs                           
     0 Path Failures, 0 SEF/AIS Secs                              
   Far End                                                        
     0 Line Code Violations, 0 Path Code Violations               
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs       
     0 Unavailable Secs 0 Path Failures                           
  Data in Interval 1:                                             
   Near End                                                       
     0 Line Code Violations, 0 Path Code Violations               
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs       
     0 Unavailable Secs, 0 Stuffed Secs                           
     1 Path Failures, 2 SEF/AIS Secs                              
   Far End                                                        
     0 Line Code Violations, 0 Path Code Violations               
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs       
     0 Unavailable Secs 0 Path Failures                           
  Total Data (last 1 15 minute intervals):                        
   Near End                                                       
     0 Line Code Violations,0 Path Code Violations,               
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs        
     0 Unavailable Secs, 0 Stuffed Secs                            
     1 Path Failures, 2 SEF/AIS Secs                               
   Far End                                                         
     0 Line Code Violations,0 Path Code Violations                 
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs        
     0 Unavailable Secs, 0 Path Failures 


 
router# sh mpls l2 vc  interface cem 0/14/0 0
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
CE0/14/0       CESoPSN Basic 0            10.1.1.1         9999       UP


router# sh mpls l2transport  vc 9090 detail 
Local interface: CE0/14/2 up, line protocol up, CESoPSN Basic 0 up
  Destination address: 10.1.1.1, VC ID: 9090, VC status: up
    Output interface: Te0/12/0, imposed label stack {130}
    Preferred path: not configured  
    Default path: active
    Next hop: 209.165.202.129
  Create time: 00:18:44, last status change time: 00:18:30
    Last label FSM state change time: 00:18:30
  Signaling protocol: LDP, peer 10.1.1.1:0 up
    Targeted Hello: 10.2.2.2(LDP Id) -> 10.1.1.1, LDP is UP
    Graceful restart: not configured and not enabled
    Non stop routing: configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 130, remote 130 
    Group ID: local 207, remote 220
    MTU: local 0, remote 0
    Remote interface description: 
  Sequencing: receive disabled, send disabled
  Control Word: On (configured: autosense)
  SSO Descriptor: 10.1.1.1/9090, local label: 130
  Dataplane:
    SSM segment/switch IDs: 1237749/557811 (used), PWID: 114
  VC statistics:
    transit packet totals: receive 0, send 0
    transit byte totals:   receive 0, send 0
    transit packet drops:  receive 0, seq error 0, send 0
ASR907# sh cem circuit interface cem 0/14/2 0
CEM0/14/2, ID: 0, Line: UP, Admin: UP, Ckt: ACTIVE
Mode :Channelized-E1, E1: 1, CEM Mode: E1-CESoP
Controller state: up, T1 state: up
Idle Pattern: 0xFF, Idle CAS: 0x8
Dejitter: 5 (In use: 0)
Payload Size: 160
Framing: Framed (DS0 channels: 1-20)
CEM Defects Set
None
Signalling: No CAS
RTP: No RTP
Ingress Pkts:    24005                Dropped:             0                   
Egress Pkts:     24005                Dropped:             0                   
CEM Counter Details
Input Errors:    0                    Output Errors:       0                   
Pkts Missing:    0                    Pkts Reordered:      0                   
Misorder Drops:  0                    JitterBuf Underrun:  0                   
Error Sec:       0                    Severly Errored Sec: 0                   
Unavailable Sec: 0                    Failure Counts:      0                   
Pkts Malformed:  0                    JitterBuf Overrun:   0                   
Generated Lbits: 0                    Received Lbits:      0                   
Generated Rbits: 0                    Received Rbits:      0                   
Generated Mbits: 0                    Received Mbits:      0

Configuring CEM Group for CESoPSN - Channelized T3 Interface

The following section describes how to configure a CEM group for CESoPSN on the channelized T3 interface:

controller MediaType 0/5/1
 mode t3
channelized
controller T3 0/5/1
 framing c-bit
 cablelength short
 t1 1 cem-group 1 timeslots 1-10 
 

Verifying CEM for CESoPSN - Channelized T3 Interface

Use the following commands to verify the pseudowire configuration for CESoPSN:

  • show cem circuit—Displays information about the circuit state, administrative state, the CEM ID of the circuit, and the interface on which it is configured. If cross connect is configured under the circuit, the command output also includes information about the attachment circuit status.

  • show mpls l2 vc—Displays information about the MPLS VC.

  • show mpls l2 vc detail—Displays detailed information about the MPLS VC.


Router# show controllers e3 0/14/2
E3 0/14/2 is up.
  Hardware is -48T3E3-CE
  Applique type is Channelized E3
  No alarms detected.
  Framing is E3 G751, Line Code is HDB3, Cablelength Short less than 225ft
  BER thresholds:  SF = 10e-10  SD = 10e-10
  Clock Source is internal, National Bit 0
  Equipment customer loopback
Data in current interval (240 seconds elapsed):                              
   Near End                                                                    
     0 Line Code Violations, 0 P-bit Coding Violations                         
     0 C-bit Coding Violations, 0 P-bit Err Secs                               
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs                    
     0 Unavailable Secs, 0 Line Errored Secs                                   
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs                       
     0 Severely Errored Line Secs, 0 Path Failures                             
     0 AIS Defect Secs, 0 LOS Defect Secs                                      
   Far End                                                                     
     0 Errored Secs, 0 Severely Errored Secs                                   
     0 C-bit Unavailable Secs, 0 Path Failures                                 
     0 Code Violations, 0 Service Affecting Secs                               
  Data in Interval 1:                                                          
   Near End                                                                    
     0 Line Code Violations, 0 P-bit Coding Violations                         
     0 C-bit Coding Violations, 0 P-bit Err Secs                               
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs                    
     20 Unavailable Secs, 20 Line Errored Secs                                 
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs                       
     20 Severely Errored Line Secs, 1 Path Failures                            
     0 AIS Defect Secs, 20 LOS Defect Secs                                     
   Far End                                                                     
     0 Errored Secs, 0 Severely Errored Secs                                   
     0 C-bit Unavailable Secs, 0 Path Failures                                 
     0 Code Violations, 0 Service Affecting Secs                               
  Total Data (last 1 15 minute intervals):                                     
   Near End                                                                    
     0 Line Code Violations, 0 P-bit Coding Violations,                        
     0 C-bit Coding Violations, 0 P-bit Err Secs,                              
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,                   
     20 Unavailable Secs, 20 Line Errored Secs,                                
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs                       
     20 Severely Errored Line Secs, 1 path failures                            
     0 AIS Defect Secs, 20 LOS Defect Secs                                     
   Far End                                                                     
     0 Errored Secs, 0 Severely Errored Secs                                   
     0 C-bit Unavailable Secs, 0 Path Failures                                 
     0 Code Violations, 0 Service Affecting Secs                               

E1 1 is up
  timeslots: 1-20
  No alarms detected.
  Framing is crc4, Clock Source is Internal, National bits are 0x1F.
  Data in current interval (250 seconds elapsed):
   Near End                                      
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs       
     0 Unavailable Secs, 0 Stuffed Secs                           
     0 Path Failures, 0 SEF/AIS Secs                              
   Far End                                                        
     0 Line Code Violations, 0 Path Code Violations               
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs       
     0 Unavailable Secs 0 Path Failures                           
  Data in Interval 1:                                             
   Near End                                                       
     0 Line Code Violations, 0 Path Code Violations               
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs       
     0 Unavailable Secs, 0 Stuffed Secs                           
     1 Path Failures, 2 SEF/AIS Secs                              
   Far End                                                        
     0 Line Code Violations, 0 Path Code Violations               
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs       
     0 Unavailable Secs 0 Path Failures                           
  Total Data (last 1 15 minute intervals):                        
   Near End                                                       
     0 Line Code Violations,0 Path Code Violations,               
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     2 Errored Secs, 0 Bursty Err Secs, 2 Severely Err Secs        
     0 Unavailable Secs, 0 Stuffed Secs                            
     1 Path Failures, 2 SEF/AIS Secs                               
   Far End                                                         
     0 Line Code Violations,0 Path Code Violations                 
     0 Slip Secs, 2 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     3 Errored Secs, 0 Bursty Err Secs, 3 Severely Err Secs        
     0 Unavailable Secs, 0 Path Failures  



router# sh mpls l2 vc  interface cem 0/14/0 0

Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
CE0/14/0       CESoPSN Basic 0            10.1.1.1         9999       UP


Router# sh mpls l2transport  vc 9090 detail 
Local interface: CE0/14/2 up, line protocol up, CESoPSN Basic 0 up
  Destination address: 10.1.1.1, VC ID: 9090, VC status: up
    Output interface: Te0/12/0, imposed label stack {130}
    Preferred path: not configured  
    Default path: active
    Next hop: 209.165.202.129
  Create time: 00:18:44, last status change time: 00:18:30
    Last label FSM state change time: 00:18:30
  Signaling protocol: LDP, peer 10.1.1.1:0 up
    Targeted Hello: 10.2.2.2(LDP Id) -> 10.1.1.1, LDP is UP
    Graceful restart: not configured and not enabled
    Non stop routing: configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 130, remote 130 
    Group ID: local 207, remote 220
    MTU: local 0, remote 0
    Remote interface description: 
  Sequencing: receive disabled, send disabled
  Control Word: On (configured: autosense)
  SSO Descriptor: 10.1.1.1/9090, local label: 130
  Dataplane:
    SSM segment/switch IDs: 1237749/557811 (used), PWID: 114
  VC statistics:
    transit packet totals: receive 0, send 0
    transit byte totals:   receive 0, send 0
    transit packet drops:  receive 0, seq error 0, send 0

Router# sh cem circuit interface cem 0/14/2 0

CEM0/14/2, ID: 0, Line: UP, Admin: UP, Ckt: ACTIVE
Mode :Channelized-E1, E1: 1, CEM Mode: E1-CESoP
Controller state: up, T1 state: up
Idle Pattern: 0xFF, Idle CAS: 0x8
Dejitter: 5 (In use: 0)
Payload Size: 160
Framing: Framed (DS0 channels: 1-20)
CEM Defects Set
None

Signalling: No CAS
RTP: No RTP

Ingress Pkts:    24005                Dropped:             0                   
Egress Pkts:     24005                Dropped:             0                   

CEM Counter Details
Input Errors:    0                    Output Errors:       0                   
Pkts Missing:    0                    Pkts Reordered:      0                   
Misorder Drops:  0                    JitterBuf Underrun:  0                   
Error Sec:       0                    Severly Errored Sec: 0                   
Unavailable Sec: 0                    Failure Counts:      0                   
Pkts Malformed:  0                    JitterBuf Overrun:   0                   
Generated Lbits: 0                    Received Lbits:      0                   
Generated Rbits: 0                    Received Rbits:      0                   
Generated Mbits: 0                    Received Mbits:      0

Configuring DS1 Local Connect on T3/E3 Interface

The following section describes how to configure the first segment for DS1 local connection:


enable
configure terminal
controller MediaType 0/5/7
 mode e3
channelized mode e1
controller E3 0/5/7
 e1 2 cem-group 1 timeslots 1-10

The following section describes how to configure the second segment for DS1 local connection:

enable
configure terminal
controller MediaType 0/5/2
 mode e3
channelized mode e1
controller E3 0/5/2
 e1 2 cem-group 1 timeslots 1-10

The following section describes how to create a DS1 local connection:


enable
configure terminal
connect ds1_connect CEM0/5/7 1 CEM CEM0/5/2  1

Verifying DS1 Local Connect on T3 Interface

Use the following commands to verify the DS1 local connection:

  • show connection name—Displays information about the connection state and segment state.


ASR907# sh xconnect all | i 0/14/7
	UP pri   ac CE0/14/2:2(CESoPSN Basic)    UP   ac CE0/14/7:2(CESoPSN Basic)    UP

ASR907# sh connection all | i 0/14/7
	38   local_t3        CE0/14/2 CESP 2        CE0/14/7 CESP 2            UP 

Configuring T3 or E3 CEP

Pre-requisites:

The default mode is channelized mode. Use no channelized command to change to non-channelized mode.

To configure T3 or E3 CEP for mode T3:

enable
controller MediaType 0/3/0
mode t3
controller t3 0/3/0
no channelized
cem-group 0 cep

To configure T3 or E3 CEP for mode E3:

enable
controller MediaType 0/3/0
mode e3
controller e3 0/3/0
no channelized
cem-group 0 cep

Configuration of Overhead C2 and J1 Bytes:

You can configure overhead C2 and J1 bytes after you configure T3 or E3 CEP.

enable
controller MediaType 0/14/44
mode e3
controller e3 0/14/44
threshold sd-ber 6
threshold sf-ber 3
no channelized
framing g751
cablelength short
cem group 0 cep
overhead j1 tx length 16
overhead j1 expected length 16

For loopback configuration, see Loopback on T3 or E3 Interfaces section.

Verifying T3 or E3 CEP Configuration

Use show controller t3 0/1/20 path to verify T3 or E3 CEP configuration:

router#show controller t3 0/1/20 path  

T3 0/1/20 PATH 1.

Asynchronous Mapping for DS3 into STS-1

TX : TDM to PSN direction
RX : PSN to TDM direction

Clock Source is internal

  AIS = 0          RDI = 0          REI = 349        BIP(B3) = 22        
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: None

TCA threshold:  B3 = 10e-6
Rx: C2 = FF
Tx: C2 = 01

Tx J1 Length : 64 
Tx J1 Trace

  72 74 72 32 20 30 2F 31 2F 32 30 2E 31 00 00 00     rtr2 0/1/20.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  72 74 72 32 20 30 2F 31 2F 32 30 2E 31 00 00 00     rtr2 0/1/20.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  72 73 70 32 20 30 2F 35 2F 31 32 2E 31 00 00 00     rsp2 0/5/12.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
rtr2#

Note


The verification output does not provide the alarm details.


STS-1 Electricals

Configuring STS-1e Modes

Configuring STS-1e Modes for Unframed SAToP

STS-1e supports unframed SAToP and you can configure STS-1e under VT-15, CT3, T3, and unframed modes. There is no default mode for STS-1e.

To configure STS-1e modes for unframed SAToP, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode {vt-15 | ct3 | t3 | unframed}
end

Note


To restore the system to its default condition, use the no form of the command.


Configuring STS-1e Modes for Framed SAToP

Starting from Cisco IOS XE Bengaluru 17.4.1, STS-1e supports framed SAToP. You can configure STS-1e under VT-15, CT3, and T3 modes for framed SAToP:

To configure STS-1e modes for framed SAToP, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode {vt-15 | ct3 | t3}
end

Configuring VT-15 Mode of STS-1e

Configuring VT-15 Mode of STS-1e for Unframed SAToP

To configure VT-15 mode of STS-1e for unframed SAToP, enter the following commands:

enable
configure terminal
controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode vt-15
vtg 1 t1 1 framing unframed
vtg 1 t1 1 cem-group 0 unframed

Configuring VT-15 Mode of STS-1e for Framed SAToP

To configure VT-15 mode of STS-1e for framed SAToP, enter the following commands:

enable
configure terminal
controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode vt-15
vtg 1 t1 1 cem-group 0 framed

Configuring T1 CT3 mode of STS-1e

Configuring T1 CT3 mode of STS-1e for Unframed SAToP

To configure T1 CT3 mode of STS-1, you can configure the T1 link using the following steps:

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode ct3
t1 1 clock source internal
t1 1 framing unframed 
end

Note


To restore the system to its default condition, use the no form of the command.


Configuring T1 CT3 mode of STS-1e for Framed SAToP

To configure T1 CT3 mode of STS-1 for framed SAToP, you can configure the T1 link using the following steps:

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode ct3
t1 1 clock source internal
t1 1 cem-group 0 framed 
end

Configuring T3 mode of STS-1e

Configuring T3 mode of STS-1e for Unframed SAToP

controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode t3
cem-group 0 unframed
t3 clock source internal

Configuring T3 mode of STS-1e for Framed SAToP

controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode t3
cem-group 0 framed
t3 clock source internal

Configuring Unframed Mode of STS-1e

controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode unframed
cem-group 0 cep

Configuring Line and Section Overhead

To configure line and section overhead, use the following commands:

enable
configure terminal
controller MediaType 0/0/16
mode sts-1e
controller sts-1e 0/0/16
overhead s1s0 2
overhead j0 tx length 1-byte
end

Note


To restore the system to its default condition, use the no form of the command.


Configuring Line Loopback

To configure loopback, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
loopback local
end

Note


To restore the system to its default condition, use the no form of the command.


Configuring AIS Shut

Alarm Indication Signal (AIS) shut when enabled on the STS-1e controller results in sending AIS alarm to peer node.

To configure AIS-Shut, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
ais-shut
end

Note


The no ais-shut command will not send AIS.


Configuring Shut

To configure Shut, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
shutdown
end

Note


Use the no shutdown command to disable the interface.


Configuring Clock

To configure clock, use the following commands:

enable
configure terminal
controller MediaType 0/0/16
mode sts-1e
controller sts-1e 0/0/16
clock source line
end

Note


The default mode is internal.



Note


ACR and DCR clock recovery are also supported.


Configuring Clock Recovery on STS-1e for Framed SAToP

Starting from Cisco IOS XE Bengaluru 17.4.1, ACR and DCR is supported on STS-1e for framed SAToP.

For more information, see Configuring Clock Recovery on STS-1e Controller for Framed SAToP.

Configuring Network-Clock STS-1e

To configure network-clock STS-1e, use the following commands:

enable
configure terminal
network-clock input-source 1 controller STS-1e 0/0/16
end

Configuring Clock Recovery on STS-1e Controller for Framed SAToP

Table 2. Feature History

Feature Name

Release Information

Description

STS1E Framed SAToP Support on IMA3G

Cisco IOS XE Bengaluru 17.4.1

Support on clock recovery on STS-1e controller for framed SAToP on the following modes:

  • T3

  • CT3

  • VT-15

Starting from Cisco IOS XE Bengaluru 17.4.1, ACR and DCR are supported on STS-1e controller for framed SAToP.

To configure the clock on STS-1e controller for framed SAToP on the T3 mode, enter the following commands:


enable
configure terminal
controller STS-1e slot/bay/port
sts-1 1
mode t3
t3 framing c-bit
cem-group 0 framed
t3 clock source recovered 1

To configure the clock on STS-1e controller for framed SAToP on the CT3 mode, enter the following commands:


enable
configure terminal
controller STS-1e slot/bay/port
sts-1 1
clock source internal
mode ct3
t3 framing c-bit
t1 1 cem-group 0 framed
t1 1 clock source recovered 1

To configure the clock on STS-1e controller for framed SAToP on the VT-15 mode, enter the following commands:


enable
configure terminal
controller STS-1e slot/bay/port
sts-1 1
mode vt-15
vtg 1 t1 1 cem-group 0 framed
vtg  1 t1 1 clock source recovered 2

The following example shows how to configure the clock on STS-1e controller for framed SAToP on the T3 mode:


enable
configure terminal
controller STS-1e 0/8/12
sts-1 1
mode t3
t3 framing c-bit
cem-group 0 framed
t3 clock source recovered 1

The following example shows how to configure the clock on STS-1e controller for framed SAToP on the CT3 mode:


enable
configure terminal
controller STS-1e 0/8/12
sts-1 1
clock source internal
mode ct3
t3 framing c-bit
t1 1 cem-group 0 framed
t1 1 clock source recovered 1

The following example shows how to configure the clock on STS-1e controller for framed SAToP on the VT-15 mode:


enable
configure terminal
controller STS-1e 0/8/12
sts-1 1
mode vt-15
vtg 1 t1 1 cem-group 0 framed
vtg 1t1 1 clock source recovered 2

Verifying STS-1e Configuration

The following sample output shows the verification of STS-1e configuration in unframed mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.                               ======> this is the controller/port status.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC3                       =======> this is the rate the port is configured on it.
 Applique type is Channelized STS1E
 Clock Source is Internal                         ===> the clocking config
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                      BIP(B1) = 0      =======> the section level alarm counter (from last clear counters)

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:26-05:28     0    49    49    49

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         =======> the line level alarm counter (from last clear counters)
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None                                     =========> present active alarms on the port.           
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6                          ====> ber thresholds
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:26-05:28     0     0     0    50     0     0      0      0  


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 01

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:26-05:28     0     0     0    48     0     0      0      0  


STS1E 0/3/14.1 PATH  mode UNFRAMED is up
  cep is configured: TRUE cem_id  :0
  clock source internal

The following sample output shows the verification of STS-1e configuration in VT-15 mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1
 Applique type is Channelized STS1E
 Clock Source is Internal
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                           BIP(B1) = 0

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:33-05:33     0     0     0     0  

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:33-05:33     0     0     0     0     0     0      0      0  


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 02
Tx: C2 = 02

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:33-05:33     0     0     0     0     0     0      0      0  


STS1E 0/3/14.1 PATH  is up.
  Hardware is A900-IMA3G-IMSG

 Applique type is VT1.5

 STS-1 1, VTG 1, VT 1 (STS1E 0/3/14.1/1/1 VT) is up
 No VT alarms detected.
  cep is configured: FALSE cem_id  (0)
  fwd_alarm_ais :0    fwd_alarm_rai :0
  Framing is unframed, Clock Source is Internal
  BIP2-tca:6, BIP2-sf:3, BIP2-sd:6
  Tx V5:1
  Rx V5:2
  Tx J2 Length=64
  TX J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Expected J2 Length=64
  Expected J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Rx J2 Length=16
  RX J2 Trace Buffer:
  CRC-7: 0x80 OK
          
  4A 44 53 55 00 00 00 00 00 00 00 00 00 00 00 00     JDSU............
  
 Data in curerent interval (1 seconds elapsed)
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs

 STS-1 1, VTG 1, T1 1 (STS1E 0/3/14.1/1/1 T1) is up
  No alarms detected.
  Framing is unframed, Clock Source is Internal
  Data in current interval (0 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

The following sample output shows the verification of STS-1e configuration in T3 mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1
 Applique type is Channelized STS1E
 Clock Source is Internal
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                           BIP(B1) = 0

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:35-05:35     0     0     0     0  

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:35-05:35     0     0     0    73     0     0      0      0  


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 04

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:26-05:36     0     0     0    12     0     0      0      0  


STS1E 0/3/14.1 T3 is up.
  Hardware is A900-IMA3G-IMSG

  Applique type is T3
  No alarms detected.
  Framing is Unframed, Cablelength is 224
  BER thresholds:  SF = 10e-3  SD = 10e-6
  Clock Source is internal
  Equipment customer loopback
  Data in current interval (560 seconds elapsed):
   Near End
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     275 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
     0 Severely Errored Line Secs, 3 Path Failures
     0 AIS Defect Secs, 0 LOS Defect Secs
   Far End
     0 Errored Secs, 0 Severely Errored Secs
     0 C-bit Unavailable Secs, 0 Path Failures
     0 Code Violations, 0 Service Affecting Secs

The following sample output shows the verification of STS-1e configuration in CT3 mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1
 Applique type is Channelized STS1E
 Clock Source is Internal
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                           BIP(B1) = 0

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:41-05:42     0    10    10    10  

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:41-05:42     0     0     0    10     0     0      0      0  


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 04

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:42-05:42     0     0     0     0     0     0      0      0  

STS1E 0/3/14.1 T3 is up.
  Hardware is A900-IMA3G-IMSG

  Applique type is Channelized T3 to T1
  No alarms detected.
  MDL transmission is disabled
    
  FEAC code received: No code is being received
  Framing is C-BIT Parity, Cablelength is 224
  BER thresholds:  SF = 10e-3  SD = 10e-6
  Clock Source is internal
  Equipment customer loopback
  Data in current interval (60 seconds elapsed):
   Near End
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     25 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
     0 Severely Errored Line Secs, 0 Path Failures
     0 AIS Defect Secs, 0 LOS Defect Secs
   Far End
     0 Errored Secs, 0 Severely Errored Secs
     0 C-bit Unavailable Secs, 0 Path Failures
     0 Code Violations, 0 Service Affecting Secs

 STS-1 1, T1 1 (STS1E 0/3/14.1/1 T1) is up
  No alarms detected.
  Framing is unframed, Clock Source is Internal
  Data in current interval (60 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     25 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

 STS-1 1, T1 2 (STS1E 0/3/14.1/2 T1) is up
  timeslots: 
  FDL per AT&T 54016 spec.
  No alarms detected.
  Framing is ESF, Clock Source is Internal
  Data in current interval (60 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     26 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

Starting with Cisco IOS XE 17.11.1, you can view the previous day performance monitoring details using the following show controller commands for the STS-1e controllers.

  • show controller sts1e

  • show controller sts1e tabular

  • show controller sts1e remote performance

  • show controller sts1e remote performance tabular


router#show controllers sts1e 0/3/0

sts1e 0/3/0 is down.
  Hardware is A900-IMA1Z8S-CX

 Port configured rate: OC3
 Applique type is Channelized Sonet
 Clock Source is Internal
Medium info:
  Type: sts1e, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 1          LOF = 0                           BIP(B1) = 0

sts1e Section Tables
  INTERVAL       CV    ES   SES  SEFS
  06:14-06:24     0   611   611   611  
  05:59-06:14     0   901   901   901  
.............
  06:29-06:44     0   901   901   901  
  06:14-06:29     0   901   901   901  
Total of Data in Current and Previous Intervals
  06:14-06:24     0 87107 87107 87107  
Total (Previous Day)
  05:29-05:29     0 86494 86494 86494

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: SLOS SLOF LAIS 
Asserted/Active Alarms: SLOS 
............
sts1e Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  06:14-06:24     0     0     0   611     0     0      0      0  
  05:59-06:14     0     0     0   901     0     0      0      0  
  05:44-05:59     0     0     0   901     0     0      0      0  
  05:29-05:44     0     0     0   901     0     0      0      0  
.............
  06:14-06:29     0     0     0   901     0     0      0      0  
Total of Data in Current and Previous Intervals
  06:14-06:24     0     0     0 87107     0     0      0      0  
Total (Previous Day)
  05:29-05:29     0     0     0 86494     0     0      0      0


PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 8         
  LOM = 0          PLM = 0          UNEQ = 0          LOP = 0   
..............
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  06:14-06:24     0     0     0   609     0     0      0      0  
  05:59-06:14     0     0     0   901     0     0      0      0  
  05:44-05:59     0     0     0   900     0     0      0      0  
  05:29-05:44     0     0     0   901     0     0      0      0  
...............
  06:29-06:44     0     0     0   900     0     0      0      0  
  06:14-06:29     0     0     0   900     0     0      0      0  
Total of Data in Current and Previous Intervals
  06:14-06:24     0     0     0 87045     0     0      0      0  
Total (Previous Day)
  05:29-05:29     0     0     0 86435     0     0      0      0

PATH 2:
Clock Source is internal
................

sts1e 0/3/0.1 PATH  is down.
  Hardware is A900-IMA1Z8S-CX

 Applique type is VT1.5

 STS-1 1, VTG 1, VT 1 (sts1e 0/3/0.1/1/1 VT) is down
 VT Receiver has LP_AIS.
  cep is configured: FALSE cem_id  (0)
  fwd_alarm_ais :0    fwd_alarm_rai :0, Clock Source is Internal
  BIP2-tca:6, BIP2-sf:3, BIP2-sd:6
  Tx V5:2
  Rx V5:0
  Tx J2 Length=64
  TX J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Expected J2 Length=64
  Expected J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Rx J2 Length=16
  RX J2 Trace Buffer:
  CRC-7: 0x60 ERROR

  C9 79 F7 0F 5F D8 5D D2 D2 7C F6 0E 53 B2 0E 00     .y.._.]..|..S...
  
 Data in curerent interval (610 seconds elapsed)
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 609 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
 Data in Interval 1:
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 901 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
................
 Data in Interval 96:
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 900 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
 Total Data (last 96 fifteen minute intervals):
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 86436 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
 Total (Previous Day): 
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 86435 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs


 STS-1 1, VTG 1, T1 1 (sts1e 0/3/0.1/1/1 T1) is down
  timeslots: 1-4
  FDL per AT&T 54016 spec.
  Receiver is getting AIS.
  Framing is ESF, Clock Source is Internal
  Data in current interval (610 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     609 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs
  Data in Interval 1:
   Near End
     0 Line Code Violations, 0 Path Code Violations
...................
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs
  Data in Interval 96:
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     900 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs
  Total Data (last 24 hours)
   Near End
     0 Line Code Violations,0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     86436 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations,0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavailable Secs
  Total (Previous Day) 
   Near End
     0 Line Code Violations,0 Path Code Violations,
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     86435 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations,0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavailable Secs

 STS-1 1, VTG 1, VT 2 (SONET 0/3/0.1/1/2 VT) is down
 VT Receiver has LP_AIS.

router#show controllers sts1e 0/3/0 tabular

Section/Line/Path same as previous.

sts1e 0/3/0.1 PATH  is down.
  Hardware is A900-IMA1Z8S-CX

 Applique type is VT1.5

 STS-1 1, VTG 1, VT 1 (SONET 0/3/0.1/1/1 VT) is down
 VT Receiver has LP_AIS.
  cep is configured: FALSE cem_id  (0)
  fwd_alarm_ais :0    fwd_alarm_rai :0, Clock Source is Internal
  BIP2-tca:6, BIP2-sf:3, BIP2-sd:6
  Tx V5:2
  Rx V5:0
  Tx J2 Length=64
  TX J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Expected J2 Length=64
  Expected J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Rx J2 Length=16
  RX J2 Trace Buffer:
  CRC-7: 0x60 ERROR

  C9 79 F7 0F 5F D8 5D D2 D2 7C F6 0E 53 B2 0E 00     .y.._.]..|..S...
  
 INTERVAL     CV-V  ES-V  SES-V  UAS-V  CV-VFE  ES-VFE  SES-VFE  UAS-VFE
 06:14-06:24     0     0      0    619       0       0        0        0  
 05:59-06:14     0     0      0    901       0       0        0        0  
 05:44-05:59     0     0      0    900       0       0        0        0  
 05:29-05:44     0     0      0    901       0       0        0        0  
 05:14-05:29     0     0      0    900       0       0        0        0  
 04:59-05:14     0     0      0    900       0       0        0        0  
...................
 06:44-06:59     0     0      0    901       0       0        0        0  
 06:29-06:44     0     0      0    900       0       0        0        0  
 06:14-06:29     0     0      0    900       0       0        0        0  
 Total           0     0      0  86436       0       0        0        0  
 Total (Previous Day):       
 05:29-05:29     0     0      0  86435       0       0        0        0


 STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) is down
  timeslots: 1-4
  FDL per AT&T 54016 spec.
  Receiver is getting AIS.
  Framing is ESF, Clock Source is Internal
  Near End Data
  INTERVAL     CV-L   ES-L   CV-P   ES-P  SES-P  CSS-P  SAS-P  UAS-P   FC-P
  06:14-06:24     0      0      0      0      0      0      0    619      0  
  05:59-06:14     0      0      0      0      0      0      0    901      0  
..............
  06:44-06:59     0      0      0      0      0      0      0    901      0  
  06:29-06:44     0      0      0      0      0      0      0    900      0  
  06:14-06:29     0      0      0      0      0      0      0    900      0  
  Total           0      0      0      0      0      0      0  86436      0  
  Total (Previous Day):     
  05:29-05:29     0      0      0      0      0      0      0  86435      0
  Far End Data
  INTERVAL     ES-LFE  ES-PFE  SES-PFE  SEFS-PFE  CSS-PFE  UAS-PFE  FC-PFE
  06:14-06:24       0       0        0         0        0        0       0  
  05:59-06:14       0       0        0         0        0        0       0  
......................
  06:29-06:44       0       0        0         0        0        0       0  
  06:14-06:29       0       0        0         0        0        0       0  
  Total             0       0        0         0        0        0       0  
  Total (Previous Day):     
  05:29-05:29       0       0        0         0        0        0       0

 STS-1 1, VTG 1, VT 2 (SONET 0/3/0.1/1/2 VT) is down
 VT Receiver has LP_AIS.
  cep is configured: FALSE cem_id  (0)
  fwd_alarm_ais :0    fwd_alarm_rai :0, Clock Source is Internal

router#show controllers sts1e 0/3/0 remote performance

Section/Line/Path same as previous.

sts1e 0/3/0.1 PATH  is down.
  Hardware is A900-IMA1Z8S-CX


 STS-1 1, VTG 1, VT 1 (VT1.5 1/1/1) - Remote Performance Data
 Far end MIB Data:
 Data in curerent interval (630 seconds elapsed)
 0 CodeViolations , 0 ErrorSecs,0 Severly Err Secs, 0 Unavail Secs
 FarEnd VT Interval data:
 Total Data (last 96 15 minute intervals):
 0 CodeViolations, 0 ErrorSec,  0 Severly Err Secs, 0 Unavail Secs

 Total (Previous Day): 
 0 CodeViolations, 0 ErrorSec,  0 Severly Err Secs, 0 Unavail Secs


 STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) - Remote Performance Data
  Data in current interval (630 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs
  Data in Interval 1:
.................
  Data in Interval 96:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs
  Total Data (last 24 hours)
     0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs
  Total (Previous Day) 
     0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

 STS-1 1, VTG 1, VT 2 (VT1.5 1/1/2) - Remote Performance Data
 Far end MIB Data:
 Data in curerent interval (630 seconds elapsed)
 0 CodeViolations , 0 ErrorSecs,0 Severly Err Secs, 0 Unavail Secs
 FarEnd VT Interval data:
 Total Data (last 96 15 minute intervals):
 0 CodeViolations, 0 ErrorSec,  0 Severly Err Secs, 0 Unavail Secs

 Total (Previous Day): 
 0 CodeViolations, 0 ErrorSec,  0 Severly Err Secs, 0 Unavail Secs

router#show controllers sts1e 0/3/0 remote performance tabular

Section/Line/Path same as previous.  


sts1e 0/3/0.1 PATH  is down.
  Hardware is A900-IMA1Z8S-CX


 STS-1 1, VTG 1, VT 1 (VT1.5 1/1/1) - Remote Performance Data
 Far end MIB Data:
 INTERVAL       CV     ES    SES   UAS
 06:14-06:24     0     0     0     0  
 FarEnd VT Interval data:
 INTERVAL       CV     ES    SES   UAS
  05:59-06:14     0     0     0     0

  05:44-05:59     0     0     0     0

  05:29-05:44     0     0     0     0

  05:14-05:29     0     0     0     0
.................
  06:29-06:44     0     0     0     0

  06:14-06:29     0     0     0     0

 Total       
  CV    ES   SES   UAS    0     0     0     0

 Total (Previous Day)       
  CV    ES   SES   UAS    0     0     0     0


 STS-1 1, VTG 1, T1 1 (SONET 0/3/0.1/1/1 T1) - Remote Performance Data
  INTERVAL      LCV   PCV   CSS  SELS   LES    DM    ES   BES   SES   UAS
  06:14-06:24     0     0     0     0     0     0     0     0     0     0
  05:59-06:14     0     0     0     0     0     0     0     0     0     0
  05:44-05:59     0     0     0     0     0     0     0     0     0     0
....................
  06:44-06:59     0     0     0     0     0     0     0     0     0     0
  06:29-06:44     0     0     0     0     0     0     0     0     0     0
  06:14-06:29     0     0     0     0     0     0     0     0     0     0  
  Total           0     0     0     0     0     0     0     0     0     0  
  Total (Previous Day)     
  05:29-05:29     0     0     0     0     0     0     0     0     0     0

 STS-1 1, VTG 1, VT 2 (VT1.5 1/1/2) - Remote Performance Data
 Far end MIB Data:
 INTERVAL       CV     ES    SES   UAS
 06:14-06:24     0     0     0     0
 FarEnd VT Interval data:
 INTERVAL       CV     ES    SES   UAS
  05:59-06:14     0     0     0     0