LEDs

Chassis LEDs

Attention, Status, Synchronization, and GPS LEDs are located both at the far left of the front of the chassis and also on the back of the chassis:

Figure 1. Chassis LEDs - Front View of Cisco 8201 Chassis
Figure 2. Chassis LEDs - Rear View of Cisco 8201 Chassis
Figure 3. Chassis LEDs - Rear View of Cisco 8202 Chassis
Figure 4. Chassis LEDs - Front View of Cisco 8201-32FH and Cisco 8201-24H8FH Routers
Figure 5. Chassis LEDs - Front View of Cisco 8202-32FH -M Chassis
Figure 6. Chassis LEDs - Front View of Cisco 8212-48FH -M Chassis

1

Attention

2

Status

3

GPS

4

Synchronization

5

1G Management Port

6

10G Management Port

7

1G and 10G Port Activity

8

GNSS

Table 1. Chassis LED Descriptions
LED Color Status

Attention

Flashing blue

The operator has activated this LED to identify this chassis.

Off

This chassis is not being identified.

Status

Green

The module is operational and has no active major or critical alarms.

Flashing Green

The auto or manual FPD upgrade is in progress.

Amber

The module is in one of the following states:

  • Power cycle

  • Reload or reimage

  • Shutdown

Flashing Amber

The module has minor alarm.

Red

Power-up failure which prevents the CPU from booting.

Flashing Red

The module has active major or critical alarms.

Off

The module is powered-off.

Synchronization

Green

Time core is synchronized to an external source including IEEE1588.

Amber

The system is running in holdover or free-run mode and it is not synchronized to an external interface.

Off

The centralized frequency or time and phase distribution is not enabled.

GPS

Green

The GPS interface is provisioned and frequency, time of day and phase inputs are all operating correctly.

Off

The GPS interface is not provisioned, or the GPS inputs are not working correctly.

Management Port

Green

The ethernet link is up and operational.

Amber

The port is either receiving or transmitting data packets.

Off

The ethernet link is down.

Management Port Activity

Green

The ethernet link is up and operational.

Amber

The port is either receiving or transmitting data packets.

Off

The ethernet link is down.

Fan Tray LED

Fan tray modules are located on the back of the chassis. Each fan tray module has a Status LED.

Figure 7. Fan Tray LED - Cisco 8201 Chassis
Figure 8. Fan Tray LED - Cisco 8202 Chassis
Figure 9. Fan Tray LED - Cisco 8201-32FH and Cisco 8201-24H8FH Routers
Figure 10. Fan Tray LED - Cisco 8202-32FH-M and Cisco 8212-48FH-M Routers

1

Fan Status LED

Table 2. Fan Tray LED Descriptions

LED

Color

Status

STATUS

Green

Fan is operating normally.

Amber

Fan tray is inserted and pending to come online.

Flashing Amber

Fan has failed.

Off

Fan is not receiving power.

Power Supply LEDs

Power modules are located on the back side of the chassis. Each power module has a Status LED.

Figure 11. Power Supply LED - 1450W

1

Status LED

2

Attention LED

Figure 12. Power Supply LED - 2000W

1

Status LED

Figure 13. Power Supply LED - Cisco 8201-32FH and Cisco 8201-24H8FH Routers
Figure 14. Power Supply LED - Cisco 8202-32FH -M Chassis
Figure 15. Power Supply LED - 8212-48FH-M Chassis

1

Status LED

Table 3. Power Supply LED Descriptions

LED

Color

Status

STATUS

Green

Power supply is on and transmitting power to the router.

Flashing Green

Power supply is connected to input power source but not transmitting power to the router.

Amber

Power supply failure, due to one of the following conditions:

  • Over voltage

  • Over current

  • Over Temperature

  • Fan failure

Flashing Amber

Power supply is operating but a warning condition has occurred, due to one of the following conditions:

  • High temperature

  • High power

  • Slow fan

Off

Power supply units are not receiving power.

Attention

Flasing Blue

The operator has activated this LED to identify this PSU.

Off

This PSU is not being identified.

Port Status LEDs

Each port has an LED. The following table describes port status LEDs.

Figure 16. Port Status LED - Cisco 8202 Chassis

1

400G Port Status LED

2

100G Port Status LED

Figure 17. Port Status LED - Cisco 8201-32FH Chassis

1

400 GbE port

2

400 GbE port status LED

Figure 18. Port Status LED - Cisco 8202-32FH -M Chassis

1

400G Port Status LED

Figure 19. Port Status LED - Cisco 8212-48FH -M Chassis

1

Port Status LED

Figure 20. Port Status LED - Cisco 8201-24H8FH Router

1

400 GbE port (blue)

3

Port status LED

2

100 GbE port

Table 4. Port Status LEDs (one per port)

LED Color

Description

Off

Port is administratively shut down.

Amber

Port is administratively enabled and the link is down.

Green

Port is administratively enabled and the link is up.