Managing RPD Associations
Feature Name |
Release information |
Description |
---|---|---|
Modernized and Refreshed UI for RPD Association |
Cisco Smart PHY 22.2 |
Modifications in the RPD Association Smart PHY UI:
|
US Port Description |
Cisco Smart PHY 22.3 |
Smart PHY can be used to set a description for the Upstream Port level. Description can be set while creating and editing RPD operations. RPD-US Port Description can be set at Port 0, Port 1 or both Port 0 and Port 1 based on RPD segmentation (1x1, 1x2 and 2x2). RPD US Port Description can be Imported & Exported. US Port Description is not a service impacting change. |
Shelf and Base Power Enhancements |
Cisco Smart PHY 22.3 |
When RPD is provisioned as a "SHELF", the ‘type shelf’ CLI is pushed to both Principal and Aux Core(s). Along with Base-power, if Tilt Pivot Freq and Tilt Slope are configured, then they are also be pushed to all the cores. |
The RPD Associations page enables you to add, organize, and update information about CMTS and RPD devices in the network. For more information, see:
Once an RPD is provisioned, the RPD may undergo state transitions as shown in the following table:
RPD Summary | RPD State | Description |
---|---|---|
ERRORED | ConfigNotFound | RPD assignment is incomplete or not specified in the Cisco Smart PHY application. |
ERRORED | ConfigPushError | Unable to push the RPD configuration to the CCAP core. |
ERRORED | ConfigReadError | Unable to obtain the existing CCAP core configuration. |
ERRORED | ConfigurationError | Assigned incorrect RPD in the Cisco Smart PHY application. |
ERRORED | GcpRedirectError | Received an error from the RPD when redirecting to the CCAP core. |
ERRORED | NotProvisioned | Cisco cBR-8 router is not provisioned with the RPD configuration. RPD configuration is not pushed to the Cisco cBR-8 router. |
ERRORED | Offline | RPD is offline. However, RPD configuration is pushed to the CCAP core. |
ERRORED | OFFLINE | RPD is offline. |
ERRORED | ResourceAllocationError | Unable to allocate resources to an RPD for the assigned CCAP core or interface. |
ERRORED | SSHKEYFETCH_FAILED | Unable to obtain the SSH key. |
GCP | GcpRedirected | Received an ACK from the RPD for the CCAP core redirect message. This redirect message captures the result of the redirect request, which is initiated by the Cisco Smart PHY application, along with the hostname, the IP address, and the interface of the redirected core. |
GCP | GcpRedirectedWithException | Received an ACK from the RPD for the CCAP core redirect message. However, one of the following errors occurred:
|
GCP | GcpRedirectStarted | RPD configuration is pushed to the CCAP core and the RPD is redirected to that core. |
GCP | GcpRedirectStartedWithException | RPD configuration is pushed to the CCAP core and the process of redirecting the RPD to that core starts. However, one of the
following errors occurs:
|
GCP | GcpUp | Received GCP message from the RPD. |
ONLINE | Online | RPD is online for the CCAP core. |
PROCESSING | ConfigPush | Configuration push to CCAP is in progress. |
PROCESSING | DeletePending | RPD pairing deletion is pending. |
PROCESSING | NORMALOPS_PROGRESS | The CCAP is returning to Normal Operation. |
PROCESSING | RECONCILIATION_PROGRESS | Reconciliation in progress |
PROCESSING | SSHKEYFETCH_IN_PROGRESS | The process of obtaining the SSH key is in progress. |
UNKNOWN | UNKNOWN | Unknown RPD State |
WARNING | OnlineWithException | RPD is online, but NDF or NDR fails. |
WARNING | PartialOnline | Partial services are available. |
WARNING | RouterVersionIncompatible | RPD software version is incompatible with the CCAP core version. |
WARNING | StaticRouteNotConfigured | Static route is not configured. |