Azimuth and Elevation Radiation Patterns
Contents of the Antenna and Bracket Kit
Dimensions of the Antenna and Brackets
Communications, Services, and Additional Information
First Published: December 22, 2020
This document describes the Cisco Aironet 2.4 GHz and 5 GHz Dual-Band Polarization-Diverse Directional Array Antenna (AIR-ANT2566D4M-DS), and provides electrical specifications and mounting instructions.
This antenna is a four-port polarization-diverse array that operates over the 2.4 GHz and 5 GHz frequency ranges. They ship with an articulating mount for use on flat surfaces and masts, and are adjustable in both horizontal and vertical planes. The radome can be painted using commonly available non-conductive spray paints, such as Krylon or Rust-Oleum.
Both antennas are designed for use in indoor and outdoor environments with an approved Cisco Catalyst series access point that requires dual-band DART antennas. The AIR-ANT2566D4M-DS antenna includes circuitry to enable self-identification of the antenna by the Cisco Catalyst 91xx Series access points.
Figure 1 2.4 GHz — Azimuth — Port A
Figure 2 2.4 GHz — Elevation — Port A
Figure 3 2.4 GHz — Azimuth — Port B
Figure 4 2.4 GHz — Elevation — Port B
Figure 5 2.4 GHz — Azimuth — Port C
Figure 6 2.4 GHz — Elevation — Port C
Figure 7 2.4 GHz — Azimuth — Port D
Figure 8 2.4 GHz — Elevation — Port D
Figure 9 5 GHz — Azimuth — Port A
Figure 10 5 GHz — Elevation — Port A
Figure 11 5 GHz — Azimuth — Port B
Figure 12 5 GHz — Elevation — Port B
Figure 13 5 GHz — Azimuth — Port C
Figure 14 5 GHz — Elevation — Port C
Figure 15 5 GHz — Azimuth — Port D
Figure 16 5 GHz — Elevation — Port D
The Self Identifying Antenna model AIR-ANT2566D4M-DS= is supported only on Cisco Catalyst 9800 Series Wireless Controllers running an IOS-XE 17.4.1 release or a later release. This antenna model is not supported on Cisco AireOS Wireless Controllers.
Warning IMPORTANT SAFETY INSTRUCTIONS
Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Read the installation instructions before using, installing, or connecting the system to the power source. Use the statement number provided at the end of each warning statement to locate its translation in the translated safety warnings for this device.
SAVE THESE INSTRUCTIONS Statement 1071
Warning Instructed person is someone who has been instructed and trained by a skilled person and takes the necessary precautions when working with equipment.
Skilled person/Qualified personnel is someone who have training or experience in the equipment technology and understand potential hazards when working with equipment. Statement 1089
Warning Only skilled person should be allowed to install, replace, or service this equipment. Refer to Statement 1089 for description of skilled person. Statement 1090
Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, as they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.: NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 280
Warning To reduce the risk of electric shock, refer to national and local codes for proper installation and grounding of antennas. Statement 1052
Warning To reduce the risk of electric shock, the shield of the coaxial cable must be connected to the building earth. Statement 1253
Each year, hundreds of people are killed or injured when attempting to install an antenna. In many of these cases, the victim was aware of the danger of electrocution, but did not take adequate steps to avoid the hazard.
For your safety, and to help you achieve a good installation, read and follow these safety precautions. They may save your life!
– Do not work on a wet or windy day.
– Do dress properly—shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
For a listing of all the warning statements and their translations, see Translated Safety Warnings for Cisco Aironet Access Points at:
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/warnings/reference/guide/ap_warn1.html
Antennas transmit and receive radio signals that are susceptible to RF obstructions and common sources of interference that can reduce throughput and the range of the device to which they are connected. Follow these guidelines to ensure the best possible performance:
– Signals penetrate paper and vinyl walls with little change to signal strength.
– Signals penetrate only one or two solid and precast concrete walls without degrading signal strength.
– Signals penetrate three or four concrete and wood block walls without degrading signal strength.
– Signals penetrate five or six walls constructed of drywall or wood without degrading signal strength.
– Signals are likely to reflect off a thick metal wall and may not penetrate it at all.
– Signals are likely to reflect off a chain link fence or wire mesh spaced between 1 and 1 1/2 inch. (2.5 and 3.8 cm). The fence acts as a harmonic reflector that blocks the signal.
Figure 17 Contents of the Antenna Bracket Kit
The dimensions noted in the following illustrations are all in mm, unless noted otherwise.
Figure 18 Dimensions of the Antenna with Brackets and Cables
Figure 19 Locations of Screw Holes and Pressure Vent at the Back of the Antenna
Figure 20 Locations of the Screw Holes on the Articulating Mount Flange
You can install the antenna on a wall or ceiling (must be a flat surface), or on a pole with a minimum diameter of 2 inches (5.08 cm) and a maximum diameter of 5 inches (12.7 cm). The antenna and one mounting flange are connected together when shipped.
Step 1 Decide on a mounting location. See the “Deciding on a Mounting Location” section.
Step 2 Ensure that you have the requisite tools and fasteners ready. See the “Tools and Equipment Required” section.
Step 3 Proceed with mounting the antenna. When mounting the antenna, assemble the bracket hardware, connect the antenna and bracket to the mounting surface, and adjust the antenna orientation.
The mounting options available are:
a. Mounting on a Wall or Ceiling
c. Flush Mounting on a Wall Without Mount Brackets
Step 4 (Optional) Paint the antenna. See the “Painting the Antenna” section.
The antenna should be mounted clear of any obstructions to the side or front of the enclosure, which contains the radiating elements. Keep in mind that this antenna should be aimed at the intended coverage area. Therefore, you should mount the antenna such that the desired mechanical tilt is achieved. If possible, mount the antenna near the access point so that you can use the shortest possible connecting cables.
Warning The fasteners and the mounting surface should be capable of maintaining a minimum pullout force of 150 pounds (68 kg) to support the weight of the antenna and bracket along with the potential wind loading on the antenna.
Warning The pole or mast must be rigid enough to hold the weight of the antenna along with the associated forces produced by wind loads. Also, the pole or mast must be structurally strong enough to withstand the clamping force of the hose clamps.
Before you start with mounting the antenna, go through the mounting procedure for each kind of installation and ensure that you have all tools and fasteners mentioned therein ready. The following is a general list of fasteners and tools which are not included in the antenna and brackets kit.
– Slotted screwdriver to tighten the screws on the hose clamps
– A 5/16 inch (8mm) socket or box wrench
Note The fasteners and mounting surface should be capable of maintaining a minimum pullout force of 150 pounds (68 kg) to support the weight of the antenna along with the potential wind loading on the antenna.
Step 1 Determine the mounting location for the antenna.
Step 2 Attach the free articulating mount flange to the wall or ceiling using four 4 mm or #8 screws and fasteners, through the holes on the bracket.
One of the two required articulating mount flange brackets come attached to the back of the antenna (see Figure 17). The other flange bracket, included in the kit, is the one used in this step.
Step 3 Assemble the bracket hardware, as shown in Figure 21. Use a flat blade screwdriver to tighten the 1/4 20 x 1.25" screws on the brackets.
Step 4 Orient the antenna correctly (note the arrow on the back of the antenna that indicates the top of the antenna). Use a flat-blade screwdriver to loosen or tighten the fasteners at the azimuth and elevation- adjustment pivots.
Step 5 Adjust the azimuth (side-to-side position) and elevation (up-and-down position) of the antenna. Loosen the adjustment pivot bolts slightly to allow for adjustment.
The azimuth angle can be adjusted ±90 degrees (Figure 23) and elevation can be adjusted ±55 degrees (Figure 24).
Use the azimuth and elevation markings on the articulating mounting arm and the flange brackets as a guide. See Figure 22.
Step 6 After adjusting the antenna position, tighten the pivot bolts. Tighten all the bolts to not more than 30 lbf.in. (3.4 Nm).
Step 7 Connect the antenna’s 4-port DART connector to the access point’s 4-DART port.
For the recommended cable type, see the “Recommended Cable” section.
Figure 21 Exploded View of Antenna and Bracket Hardware Assembly
Figure 22 Close-Up View of the Azimuth and Elevation-Adjustment Pivots
Figure 24 Elevation Adjustment
Note The pole or mast must be rigid enough to hold the weight of an antenna along with the associated forces produced by wind loads. In addition, the mast must be structurally strong enough to withstand the clamping force of the hose clamps.
Step 1 Determine the mounting location for the antenna on the pole or mast.
Step 2 Position and mount the mounting flange bracket on to the pole or mast using the hose clamps provided in the kit. The hose clamps should pass through the slots on the free mounting flange bracket.
One of the two required articulating mount flange brackets come attached to the back of the antenna (see Figure 17). The other flange bracket, included in the kit, is the one used in this step.
Step 3 Tighten the hose clamps only to the extent that they can hold the flange bracket and the antenna in place until the antenna is positioned at its final position. Use a slotted screwdriver to tighten the screws on the hose clamps.
Step 4 Assemble the antenna and bracket to the flange bracket. See Figure 21.
Step 5 Position the antenna, mounting bracket, and hose clamps on the mast. See Figure 25 for reference.
Step 6 Tighten the hose clamps until the antenna is fully secure on the mast. Ensure that the antenna cannot rotate about the mast.
Step 7 After the antenna is secured on the mast, adjust the azimuth (side-to-side position) and elevation (up-and-down position) of the antenna. Loosen the adjustment pivot bolts slightly to allow for adjustment.
Azimuth angle can be adjusted ±90 degrees (Figure 23) and elevation can be adjusted ±55 degrees (Figure 24).
You can use the azimuth and elevation markings on the articulating mounting arm and the flange brackets as a guide. See Figure 22.
Step 8 After you adjust the antenna position, tighten the adjustment bolts. Tighten all the bolts to not more than 30 lbf.in. (3.4 Nm).
Step 9 Connect the antenna’s 4-port DART connector to the access point’s 4-DART port.
For the recommended cable type, see the “Recommended Cable” section.
Figure 25 Antenna Bracket Hose Clamp Assembly for Pole Mounting
You can flush mount the antenna on a wall. For this, you will need to discard the articulating mount flange brackets from the installation.
Note The following procedure describes how to mount the antenna on a drywall. If you intend to install your antenna on another surface other than a drywall, the following procedure may vary slightly and you should procure the necessary hardware.
Step 1 Remove the articulating mount flange bracket that comes attached to the back of the antenna.
Step 2 Determine the location where you will mount the antenna.
Step 3 Use the antenna as a template to mark the location of the four mounting holes. See Figure 26 for the locations of the holes.
Step 4 Using a drill and #29 drill bit, drill four holes at the locations you have marked in Step 3. For drywall installations a #29 (0.136 inch or 45 mm) drill bit is enough. Other surfaces may require a different size.
Step 5 Insert 8-inch plastic wall anchors into each hole.
Step 6 Using a mallet or small hammer, properly seat the plastic anchors into the wall.
Step 7 Align the antenna's mounting holes with the anchors.
Step 8 Insert an 8 x 1¼-inch screw, through each mounting hole and into its anchor.
Step 9 Tighten the screws using a Phillips screwdriver. Do not overtighten.
Step 10 Connect the antenna’s 4-port DART connector to the access point’s 4-DART port.
For the recommended cable type, see the “Recommended Cable” section.
Figure 26 Back of the Antenna with Flush Mounting Screw-Holes Locations
Screw holes for flush mounting on a wall. Each hole takes an 8 x 1¼-inch screw. See Figure 18 for the distances between these holes. |
|||
Spot where the pre-installed articulating flange mount was removed from. |
The AIR-ANT2566D4M-DS has a 4-port DART connector which is connected to the access point’s 4-DART port.
The antenna includes circuitry to enable self-identification of the antenna by the Cisco Catalyst 91xx Series access points. The antenna has a built-in EEPROM that can be read by the AP to automatically configure the antenna type and gain in the wireless controller.
This antenna comes with a 3 ft long, bundled cable.
Note A coaxial cable loses efficiency as the frequency increases, resulting in signal loss. The cable should be kept as short as possible because cable length also determines the amount of signal loss (the longer the cable, the greater the loss).
Painting the antenna and the bracket does not affect its performance if you use standard exterior-grade, oil-based, or latex paint. Do not use metallic or metallic-flake paints, which will degrade antenna performance.
Note Before painting the antenna, cover the pressure-release vent on the rear, lower-left of the antenna with masking tape to prevent clogging. Ensure that you remove the tape afterwards.
We recommend that you use Krylon Fusion for Plastic or Rust-Oleum for Plastic (which might require a primer coat). For best results, follow the surface preparation suggestions from the paint manufacturer.
Cisco Bug Search Tool (BST) is a web-based tool that acts as a gateway to the Cisco bug tracking system that maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. BST provides you with detailed defect information about your products and software.