Table of Contents
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(2)JB3
Finding the Cisco IOS Software Release
Upgrading to a New Software Release
Disabling Radios to Prevent Unexpected Reboots When Upgrading the System Software
New Features and Important Installation Notes
Obtaining Documentation and Submitting a Service Request
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(2)JB3
These release notes describe features, enhancements, and caveats for Cisco Autonomous AP IOS Release 15.2(2)JB3. This release supports the following Cisco Aironet autonomous access points:
- AP 802
- AP1260
- AP 1040
- AP 1140
- AP 3500i
- AP 3500e
- AP 3600i
- AP 3600e
- AP 2600i
- AP 2600e
- AP 1600i
- AP 1600e
- AP 1550
Cisco IOS Release 15.2(2)JB3 does not support the following Cisco Aironet access points:
Note You cannot use HTTPS file transfer to upgrade to Cisco IOS Release 15.2(2)JB from previous releases. Because of the image size for this release, you must use TFTP or FTP file transfer for the upgrade. Refer to the upgrade instructions at this URL:
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b-chap20-firmware.html#wp1035507
Introduction
The Cisco Aironet Access Point is a wireless LAN transceiver that acts as the connection point between wireless and wired networks or as the center point of a standalone wireless network. In large installations, the roaming functionality provided by multiple access points enables wireless users to move freely throughout the facility while maintaining uninterrupted access to the network.
System Requirements
You can install the 32 MB Cisco IOS Release 15.2(2)JB3 on all 1260, 1040, 1140, 3500i, 3500e, 3600i, 3600e, 2600i, 2600e, 1600i, 1600e, and 1550 series access points.
Finding the Cisco IOS Software Release
To find the version of Cisco IOS software that is running on your access point, use a Telnet session to log into the access point, and enter the show version EXEC command.
On access points running Cisco IOS software, you can also find the software release on the System Software Version page in the access point’s web-browser interface. If your access point does not run Cisco IOS software, the software release appears at the top left of most pages in the web-browser interface.
Upgrading to a New Software Release
Note You cannot use HTTPS file transfer to upgrade to Cisco IOS Release 15.2(2)JA from previous releases. Because of the image size for this release, you must use TFTP or FTP file transfer for the upgrade. Refer to the upgrade instructions at this URL:
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b-chap20-firmware.html#wp1035507
To upgrade your access point or bridge software, follow these steps:
Step 1 Follow this link to the Cisco home page:
Step 2 Click Support. The Support and Documentation page appears.
Step 3 Under the Select a Product Name, click Wireless. The Product/Technology Support page appears.
Step 4 Under the Make a Selection to Continue section, click Access Point. Products and Access Point are highlighted.
Step 5 Select the access point model for which you need the information. For example, click the Cisco Aironet 1260 series. A list of documents appears.
Step 6 Click Configure. A list of configuration documents appears.
Step 7 Click Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 15.2(2)JB3 .
Step 8 Navigate to the Managing Firmware and Software chapter.
For information on Cisco IOS software, click this link to browse to the Cisco IOS Software Center on Cisco.com:
Disabling Radios to Prevent Unexpected Reboots When Upgrading the System Software
If your access point runs Cisco IOS Release 12.2(11)JA, 12.2(11)JA1, or 12.2(11)JA2, your access point might unexpectedly reboot after you upgrade to a later Cisco IOS release. Because of a rare timing condition that affects the radios, the access point sometimes reboots immediately after the upgrade when the radios are enabled. However, after the access point reboots, the upgrade is complete and the access point operates normally. To prevent the access point from rebooting unexpectedly, disable the radio interfaces before upgrading the software.
To disable the radio interfaces using the access point’s web-browser interface, which you can access through the access point's Ethernet port, follow these steps:
Step 1 Browse to the Network Interfaces: Radio Settings page. Figure 1 shows the top portion of the Network Interfaces: Radio Settings page.
Figure 1 Network Interfaces: Radio Settings Page
Step 2 Choose Disable to disable the radio.
Step 3 Click Apply at the bottom of the page.
Step 4 If your access point has two radios, repeat these steps for the second radio.
Beginning in privileged EXEC mode, follow these steps to disable the access point radios using the access point CLI:
Enters interface configuration mode for the radio interface. The 2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.
If your access point has two radios, repeat these steps for the second radio. Use the no form of the shutdown command to enable the radio.
New Features and Important Installation Notes
No new features have been introduced in this release. Features introduced in Cisco IOS Release 15.2(2)JB2 continue to be supported.
For information on new features, and important notes on installing the software, see the release notes for Cisco IOS Release 15.2(2)JB2, at:
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ios/release/notes/15-2_2_JB2.html
Caveats
This section lists Open Caveats and Resolved Caveats for access points and bridges in Cisco IOS Release 15.2(2)JB3. For your convenience in locating caveats in Cisco’s Bug Toolkit, the caveat titles listed in this section are drawn directly from the Bug Toolkit database. These caveat titles are not intended to be read as complete sentences because the title field length is limited. In the caveat titles, some truncation of wording or punctuation might be necessary to provide the most complete and concise description. The only modifications made to these titles are as follows:
- Commands are in boldface type.
- Product names and acronyms may be standardized.
- Spelling errors and typos may be corrected.
Note If you are a registered cisco.com user, view Bug Toolkit on cisco.com at the following website: http://tools.cisco.com/Support/BugToolKit/
To become a registered cisco.com user, go to the following website:
https://tools.cisco.com/RPF/register/register.do
Open Caveats
The following table lists caveats that are open in Cisco IOS Release 15.2(2)JB3.
Resolved Caveats
The following table lists caveats that are resolved in Cisco IOS Release 15.2(2)JB3.
If You Need More Information
If you need information about a specific caveat that does not appear in these release notes, you can use the Cisco Bug Toolkit to find select caveats of any severity. Click this URL to browse to the Bug Toolkit:
http://tools.cisco.com/Support/BugToolKit/
(If you request a defect that cannot be displayed, the defect number might not exist, the defect might not yet have a customer-visible description, or the defect might be marked Cisco Confidential.)
Troubleshooting
For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at http://www.cisco.com/cisco/web/support/index.html . Click Technology Support, choose Wireless from the menu on the left, and click Wireless LAN.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation .
To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What’s New in Cisco Product Documentation RSS feed . The RSS feeds are a free service.
© 2013-2017 Cisco Systems, Inc. All rights reserved.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)