Cable and Connectors
Connector Specifications
10/100/1000 Ports
The 10/100/1000 Ethernet ports on the switches use RJ-45 connectors.
![](/content/dam/en/us/td/i/000001-100000/60001-65000/60001-61000/60915.ps/jcr:content/renditions/60915.jpg)
![]() Note |
Connector pins 1, 2, 3, and 6 are used for PoE. |
SFP Module Connectors
The illustration below shows an LC style connector that is used with the SFP Module slots. It is a fiber-optic cable connector.
![](/content/dam/en/us/td/i/000001-100000/55001-60000/58001-59000/58476.ps/jcr:content/renditions/58476.jpg)
![]() Warning |
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments. Statement 1051 |
Console Port
The switch has two console ports: a USB 5-pin mini-Type B port on the front panel (see image below) and an RJ-45 console port on the rear panel.
![](/content/dam/en/us/td/i/200001-300000/250001-260000/253001-254000/253163.eps/jcr:content/renditions/253163.jpg)
The USB console port uses a USB Type A to 5-pin mini-Type B cable, shown in the illustration below. The USB Type A-to-USB mini-Type B cable is not supplied.
![]() Note |
When running Linux, access the USB Console using Minicom instead of Screen . |
![](/content/dam/en/us/td/i/200001-300000/250001-260000/253001-254000/253405.eps/jcr:content/renditions/253405.jpg)
The RJ-45 console port uses an 8-pin RJ-45 connector The supplied RJ-45-to-DB-9 adapter cable is used to connect the console port of the switch to a console PC. You need to provide a RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console port to a terminal. You can order a kit (part number ACS-DSBUASYN=) containing that adapter.
Alarm Port
The labels for the alarm connector pin-outs are on the switch panel and are displayed below.
Label |
Connection |
---|---|
NO |
Alarm Output Normally Open (NO) connection |
COM |
Alarm Output Common connection |
NC |
Alarm Output Normally Closed (NC) connection |
IN2 |
Alarm Input 2 |
REF |
Alarm Input Reference Ground connection |
IN1 |
Alarm Input 1 |
Cables and Adapters
SFP Module Cables
Each port must match the wave-length specifications on each end of the cable, and for reliable communications, the cable must not exceed the allowable length. Refer to the Data Sheets for the complete list of supported SFP Modules and cables.
![]() Note |
|
Cable Pinouts
![](/content/dam/en/us/td/i/000001-100000/65001-70000/65001-66000/65271.ps/jcr:content/renditions/65271.jpg)
![](/content/dam/en/us/td/i/000001-100000/65001-70000/65001-66000/65274.ps/jcr:content/renditions/65274.jpg)
To identify a crossover cable, hold the cable ends side-by-side, with the tab at the back. The wire connected to pin 1 on the left end should be the same color as the wire connected to pin 3 on the right end. The wire connected to pin 2 on the left end should be the same color as the wire connected to pin 6 on the right end.
![](/content/dam/en/us/td/i/200001-300000/270001-280000/273001-274000/273807.eps/jcr:content/renditions/273807.jpg)
Console Port Adapter Pinouts
The console port uses an 8-pin RJ-45 connector. If you did not order a console cable, you need to provide an RJ-45-to-DB-9 adapter cable to connect the switch console port to a PC console port. You need to provide an RJ-45-to-DB-25 female DTE adapter if you want to connect the switch console port to a terminal.
Switch ConsolePort (DTE) |
RJ-45-to-DB-9Terminal Adapter |
ConsoleDevice |
---|---|---|
Signal |
DB-9 Pin |
Signal |
RTS |
8 |
CTS |
DTR |
6 |
DSR |
TxD |
2 |
RxD |
GND |
5 |
GND |
RxD |
3 |
TxD |
DSR |
4 |
DTR |
CTS |
7 |
RTS |
![]() Note |
The RJ-45-to-DB-25 female DTE adapter is not supplied with the switch. |
SwitchConsolePort (DTE) |
RJ-45-to-DB-25Adapter |
ConsoleDevice |
---|---|---|
Signal |
DB-25 Pin |
Signal |
RTS |
5 |
CTS |
DTR |
6 |
DSR |
TxD |
3 |
RxD |
GND |
7 |
GND |
RxD |
2 |
TxD |
DSR |
20 |
DTR |
CTS |
4 |
RTS |