Release Notes for Cisco IOS Release 15.2(6)E0a
New Features in Cisco IOS Release 15.2(6)E0a
Finding the Software Version and Feature Set
IOS/IOx Upgrade Considerations
Upgrading a Switch by Using the CLI
Upgrading IOS and FPGA on the Ethernet Switch Module (ESM)
First Published: October 30, 2017
Cisco IOS Release 15.2(6)E0a runs on these platforms:
■Cisco 2500 Series Connected Grid Switches (CGS 2520)
■Cisco Connected Grid Ethernet Switch Module (CGR 2010 ESM)
■Cisco Embedded Service 2020 Series Switches (ESS 2020)
■Cisco Industrial Ethernet 2000 Series Switches (IE 2000)
■Cisco Industrial Ethernet 2000U Series Switches (IE 2000U)
■Cisco Industrial Ethernet 3000 Series Switches (IE 3000)
■Cisco Industrial Ethernet 3010 Series Switches (IE 3010)
■Cisco Industrial Ethernet 4000 Series Switches (IE 4000)
■Cisco Industrial Ethernet 4010 Series Switches (IE 4010)
■Cisco Industrial Ethernet 5000 Series Switches (IE 5000)
These release notes include important information about Cisco IOS Release 15.2(6)E0a and any limitations, restrictions, and caveats that apply to the release. Verify that these release notes are correct for your switch:
■If you are installing a new switch, see the Cisco IOS release label on the rear panel of your switch.
■If your switch is on, use the show version command. See Finding the Software Version and Feature Set.
■If you are upgrading to a new release, see the software upgrade filename for the software version. See Deciding Which Files to Use.
For a complete list of documentation for the platforms associated with this release, see Related Documentation.
You can download the switch software from this site (registered Cisco.com users with a login password):
http://software.cisco.com/download/navigator.html
This document uses the following conventions.
Note: Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.
Caution: Means reader be careful. In this situation, you might perform an action that could result in equipment damage or loss of data.
Warning: IMPORTANT SAFETY INSTRUCTIONS
Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
SAVE THESE INSTRUCTIONS
Regulatory: Provided for additional information and to comply with regulatory and customer requirements.
New Feature Summary for Cisco IOS Release 15.2(6)E0a lists new features added in Cisco IOS Release 15.2(6)E0a.
Embedded GNSS receiver within the IE 5000 enables the switch to determine its own location and get accurate time from a satellite constellation and serve as the source (Grand Master Clock) for time distribution in the network. |
|||
■Statistics for PRP Ports – contents, display (CLI and Device Manager) PRP provides hitless redundancy (zero recovery time) after a failure by providing end nodes, identified as dually-attached nodes (DANs) provide access to two independent, disjointed, parallel networks (LAN-A, LAN-B). (IEC 62439-3) |
|||
Precision time Protocol (PTP) over Parallel Redundancy Protocol (PRP) |
PTP is supported over both LAN A and LAN B in the PRP network to provide redundancy for PTP. |
Parallel Redundancy Protocol (PRP) for IE 4000, IE 4010, and IE 5000 Switches |
|
High-availability Seamless Redundancy (HSR) is defined in International Standard IEC 62439-3-2016 Clause 5. HSR is similar to Parallel Redundancy Protocol (PRP) in providing hitless redundancy. HSR is designed to work in a ring topology rather than two parallel independent networks of any topology (LAN-A and LAN-B), HSR defines a ring with traffic in opposite directions. Port-A sends traffic counter clockwise in the ring, and Port-B sends traffic clockwise. |
High-Availability Seamless Redundancy (HSR) for IE 4000 Configuration Guide |
||
CISCO-ENTITY-SENSOR-MIB is used for SNMP support for sensors on IE switches instead of ENTITY-SENSOR-MIB. |
|||
QinQ support is moved to Lanbase license for IE 4000 and IE 5000. |
|||
Allows tracking and ensures protected communication between peers. |
|||
IE 4000 Fiber SFP transceivers via combo ports are now visible to SIMATIC TIA Portal. Note: The combo port works in both copper and fiber mode. Note: IE 2000 and IE 5000 already support this capability. Initial support was supported in Cisco IOS Release 15.2(5)E2. |
Pluggable Transceiver (SFP) Configuration Guide for SIMATIC STEP7/TIA Portal |
||
Configure Open Plug and Play (PnP) server settings to allow a switch to send a work request to a PnP server such as Industrial Network Director (IND) to allow further device configuration. |
|||
IND baseline configuration - Changes within Device Manager to make IOT switches IND discoverable. |
|||
Feature Mode manages the FPGA resources for a given set of features. The feature mode setting determines if TSN or HSR features are operational. Availability of Feature Mode on the switch is determined by supported features, applicable software licenses, and currently applied Feature Mode. The switch is configured with a default Feature Mode. The default Feature Mode is the most commonly-used feature. In a running system, if you deactivate the current active Feature Mode, the default mode will be applied. |
|||
PnP configuration support in Device Manager - On Express setup, the user will point to the PNP server. The switch will send work request to the PNP server for further device configuration. |
|||
MOTD - You can configure a Message of the Day (MOTD) banner to be displayed on the Device Manager Dashboard. |
|||
RSTP/MSTP bridge priority and diagnosis capability - You can select RSTP/MSTP bridge priority per port and display spanning-tree information for the selected VLAN. |
|||
Auto-Logout - If the device manager session is left inactive for the duration of the configured timeout value, the session will be logged out and the user must be re-authenticated. By default session timeout is 3 minutes. The timeout now can be configured only from CLI: ip http session-idle-timeout <1-1200> The session timeout value configured while a user is logged in to DM will be used for auto-logout. |
|||
Online help for the Device Manager is available in the following languages: |
This section describes the following system requirements for Cisco IOS Release 15.2(6)E0a:
This section summarizes the hardware and software requirements for the Windows platform.
For a listing of Express Setup documentation, see Methods for Assigning IP Information.
■1 gigahertz (GHz) or faster 32-bit (x86) or 64-bit (x64) processor
■1 gigabyte (GB) RAM (32-bit) or 2 GB RAM (64-bit)
■16 GB available hard disk space (32-bit) or 20 GB (64-bit)
■PC with Windows 7, Windows 10, or Mac OS 10.6.x
■Web browser (Internet Explorer 10.0 or 11.0, or Firefox 48.x and above) with JavaScript enabled
■Straight-through or crossover Category 5 or 6 cable
Express Setup verifies the browser version when starting a session, and it does not require a plug-in.
These are the procedures for downloading software. Before downloading software, read these sections for important information:
■Finding the Software Version and Feature Set
■IOS/IOx Upgrade Considerations
■Upgrading a Switch by Using the CLI
The Cisco IOS image is stored as a bin file in a directory that is named with the Cisco IOS release. A subdirectory contains the files needed for web management. The image is stored on the compact flash memory card.
You can use the show version privileged EXEC command to see the software version that is running on your switch. The second line of the display shows the version.
You can also use the dir filesystem : privileged EXEC command to see the directory names of other software images stored in flash memory. For example, use the dir flash: command to display the images in the flash memory.
The upgrade procedures in these release notes describe how to perform the upgrade by using a combined tar file. This file contains the Cisco IOS image file and the files needed for the embedded device manager. You must use the combined tar file to upgrade the switch through Express Setup. To upgrade the switch through the command-line interface (CLI), use the tar file and the archive download-sw privileged EXEC command.
Cisco IOS Software Image Files lists the filenames for this software release.
Note: If you download the IP services image and plan to use Layer 3 functionality, you must use the Switch Database Management (SDM) routing template. To determine the currently active template, enter the show sdm prefer privileged EXEC command. If necessary, enter the sdm prefer global configuration command to change the SDM template to a specific template. For example, if the switch uses Layer 3 routing, change the SDM template from the default to the routing template. You must reload the switch for the new template to take effect.
Note: Beginning with Cisco IOS Release 15.2(5)E, we no longer release the IE 3000 IP services image. The latest release for the IP services image on the IE 3000 is 15.2(4)EA1.
Before upgrading, note the following Cisco IOS/IOx version incompatibilities:
■With switch running Cisco IOS 15.2(5)E2, IOX upgrade from version 1.3 to 1.4 and higher is not supported
■IOx 1.3 is not supported in Cisco IOS 15.2(6)E2 and higher
We recommend that you upgrade using the IOS and IOx bundle image to move to the higher version software. IOS/IOx bundle images will always have a compatible combination of IOS and IOx.
Before upgrading your switch software, make sure that you archive copies of both your current Cisco IOS release and the Cisco IOS release to which you are upgrading. Keep these archived images until you have upgraded all devices in the network to the new Cisco IOS image and verified that the new Cisco IOS image works properly in your network.
Cisco routinely removes old Cisco IOS versions from Cisco.com. See Product Bulletin 2863 for information:
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps8802/ps6969/ps1835/prod_bulletin0900aecd80281c0e.html
You can copy the bin software image file on the flash memory to the appropriate TFTP directory on a host by using the copy flash: tftp: privileged EXEC command.
Note: Although you can copy any file on the flash memory to the TFTP server, it is time consuming to copy all of the HTML files in the tar file. We recommend that you download the tar file from Cisco.com and archive it on an internal host in your network.
You can also configure the switch as a TFTP server to copy files from one switch to another without using an external TFTP server by using the tftp-server global configuration command.
This procedure is for copying the combined tar file to the switch. You copy the file to the switch from a TFTP server and extract the files. You can download an image file and replace or keep the current image.
Note: Make sure that the compact flash card is in the switch before downloading the software.
To download software, follow these steps:
1. Use Cisco IOS Software Image Files to identify the file that you want to download.
2. Download the software image file. If you have a SMARTnet support contract, go to this URL, and log in to download the appropriate files:
http://software.cisco.com/download/navigator.html
For example, to download the image for an IE 2000 switch, select Products > Switches > Industrial Ethernet Switches > Cisco Industrial Ethernet 2000 Series Switches, then select your switch model. Select IOS Software for Software Type, then select the image you want to download.
3. Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP server is properly configured.
For more information, see the “Assigning the Switch IP Address and Default Gateway” chapter in the applicable document for your switch as listed in Methods for Assigning IP Information.
4. Log into the switch through the console port or a Telnet session.
5. (Optional) Ensure that you have IP connectivity to the TFTP server by entering this privileged EXEC command:
For more information about assigning an IP address and default gateway to the switch, see Methods for Assigning IP Information.
6. Download the image file from the TFTP server to the switch.
If you are installing the same version of software that currently exists on the switch, overwrite the current image by entering this privileged EXEC command:
The command above untars/unzips the file.The system prompts you when it completes successfully.
–The /overwrite option overwrites the software image in flash memory with the downloaded one.
If you specify the command without the /overwrite option, the download algorithm verifies that the new image is not the same as the one on the switch Flash device. If the images are the same, the download does not occur. If the images are different, the old image is deleted, and the new one is downloaded. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.
–The /reload option reloads the system after downloading the image unless the configuration has been changed and not saved.
–For // location, specify the IP address of the TFTP server. or hostname.
–For / directory / image-name .tar, specify the directory and the image to download. Directory and image names are case sensitive. The directory is for file organization and it is generally a tftpboot/user-ID path.
This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite the image on the switch:
You can also download the image file from the TFTP server to the switch and keep the current image by replacing the /overwrite option with the /leave-old-sw option. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.
This procedure is for copying the combined tar file to the switch. You copy the file to the switch from a TFTP server and extract the files. You can download an image file and replace or keep the current image.
To download software, follow these steps:
1. Refer to Deciding Which Files to Use to identify the file that you want to download.
2. Download the software image file. If you have a SMARTnet support contract, go to the URL below and log in to download the appropriate files.
http://software.cisco.com/download/navigator.html
For example, to download the image for a Connected Grid 10-Port Ethernet Switch Module Interface Card, select Products > Cisco Interfaces and Modules > Connected Grid Modules > Connected Grid 10-Port Ethernet Switch Module Interface Card. Select IOS Software for Software Type, then select the image you want to download.
Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP server is properly configured. For more information, see the “Assigning the Switch IP Address and Default Gateway” chapter in the applicable document listed in Methods for Assigning IP Information.
3. Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP server is properly configured.
4. Log in to the switch through the console port or a Telnet session.
5. (Optional) Ensure that you IP connectivity to the TFTP server by entering this privileged EXEC command:
6. Download the image file from the TFTP server to the switch.
If you are installing the same version of software that currently exists on the switch, overwrite the current image by entering this privileged EXEC command:
The command above untars/unzips the file.The system prompts you when it completes successfully.
–The /overwrite option overwrites the software image in flash memory with the downloaded one.
If you specify the command without the /overwrite option, the download algorithm verifies that the new image is not the same as the one on the switch Flash device. If the images are the same, the download does not occur. If the images are different, the old image is deleted, and the new one is downloaded. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.
–The /reload option reloads the system after downloading the image unless the configuration has been changed and not saved.
–For // location, specify the IP address of the TFTP server. or hostname.
–For / directory / image-name .tar, specify the directory and the image to download. Directory and image names are case sensitive. The directory is for file organization and it is generally a tftpboot/user-ID path.
This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite the image on the switch:
You can also download the image file from the TFTP server to the switch and keep the current image by replacing the /overwrite option with the /leave-old-sw option. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.
7. After the download and the untar are complete, power cycle the CGR2010.
You can assign IP information to your switch using the methods shown in Methods for Assigning IP Information
The Bug Search Tool (BST), which is the online successor to Bug Toolkit, is designed to improve the effectiveness in network risk management and device troubleshooting. The BST allows partners and customers to search for software bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. The tool has a provision to filter bugs based on credentials to provide external and internal bug views for the search input.
To view the details of a caveat listed in this document:
1. Access the BST (use your Cisco user ID and password) at https://tools.cisco.com/bugsearch/.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)
No combinations are authorized or intended under this document.