Perform Preliminary Checks

After successfully logging into the console, you must perform some preliminary checks to verify the default setup. If any setup issue is detected, take corrective action before making further configurations.


Note


The output of the examples in the procedures is not from the latest software release. The output will change for any explicit references to the current release.


Verify Status of Hardware Components

To verify the status of all the hardware components installed on NCS 1010, perform the following procedure.

Before you begin

Ensure that all the required hardware components are installed on NCS 1010. For installation details, see Cisco Network Convergence System 1010 Hardware Installation Guide.

Procedure


show platform

When you execute this command, the status of Cisco IOS XR is displayed.

Example:

RP/0/RP0/CPU0:ios#show platform     
Wed Apr 27 08:43:40.130 UTC
Node              Type                     State                    Config state
--------------------------------------------------------------------------------
0/RP0/CPU0        NCS1010-CNTLR-K9(Active) IOS XR RUN               NSHUT,NMON
0/PM0             NCS1010-AC-PSU           OFFLINE                  NSHUT,NMON
0/PM1             NCS1010-AC-PSU           OPERATIONAL              NSHUT,NMON
0/FT0             NCS1010-FAN              OPERATIONAL              NSHUT,NMON
0/FT1             NCS1010-FAN              OPERATIONAL              NSHUT,NMON
0/0/NXR0          NCS1K-OLT-C              OPERATIONAL              NSHUT,NMON
0/1               NCS1K-BRK-SA             OPERATIONAL              NSHUT,NMON
0/1/0             NCS1K-BRK-8              OPERATIONAL              NSHUT,NMON
0/1/1             NCS1K-BRK-8              OPERATIONAL              NSHUT,NMON
0/1/2             NCS1K-BRK-24             OPERATIONAL              NSHUT,NMON
0/1/3             NCS1K-BRK-24             OPERATIONAL              NSHUT,NMON
0/2               NCS1K-MD-32E-C           OPERATIONAL              NSHUT,NMON
0/3               NCS1K-MD-32O-C           OPERATIONAL              NSHUT,NMON
RP/0/RP0/CPU0:ios#show platform
Thu Mar  2 12:35:01.883 IST
Node              Type                     State                    Config state
--------------------------------------------------------------------------------
0/RP0/CPU0        NCS1010-CNTLR-K9(Active) IOS XR RUN               NSHUT,NMON
0/PM0             NCS1010-AC-PSU           OPERATIONAL              NSHUT,NMON
0/PM1             NCS1010-AC-PSU           OFFLINE                  NSHUT,NMON
0/FT0             NCS1010-FAN              OPERATIONAL              NSHUT,NMON
0/FT1             NCS1010-FAN              OPERATIONAL              NSHUT,NMON
0/0/NXR0          NCS1K-OLT-L              OPERATIONAL              NSHUT,NMON
0/3               NCS1K-BRK-24             OPERATIONAL              NSHUT,NMON

Verify that all the components of NCS 1010 are displayed in output. The state must be in the OPERATIONAL state. The various states are:

  • OPERATIONAL—Node is operating normally and is fully functional.

  • POWERED_ON—Power is on and the node is booting up.

  • FAILED—Node is powered on but has encountered an internal failure.

  • PRESENT—Node is in intermediate state in the boot sequence.

  • POWERED_OFF—Power is off and the node cannot be accessed.

  • IOS XR RUN—Node is running IOS XR.

  • OFFLINE—Input power is not connected to the power modules.


Verify Inventory

The show inventory command displays details of the hardware inventory of NCS 1010.

To verify the inventory information for all the physical entities, perform the following procedure.

Procedure


show inventory

Displays the details of the physical entities of NCS 1010 along with the details of SFPs.

Example:

RP/0/RP0/CPU0:ios#show inventory    
Wed Apr 27 08:43:44.222 UTC

NAME: "Rack 0", DESCR: "NCS1010 - Shelf Assembly"
PID: NCS1010-SA        , VID: V00, SN: FCB2504B0X4

NAME: "0/RP0/CPU0", DESCR: "Network Convergence System 1010 Controller"
PID: NCS1010-CNTLR-K9  , VID: V00, SN: FCB2506B0NX

NAME: "0/1", DESCR: "NCS 1000 shelf for 4 passive modules"
PID: NCS1K-BRK-SA      , VID: V00 , SN: FCB2534B0GR

NAME: "0/1/0", DESCR: "NCS 1000 MTP/MPO to 8 port passive breakout module"
PID: NCS1K-BRK-8       , VID: V00 , SN: MPM25401005

NAME: "0/1/1", DESCR: "NCS 1000 MTP/MPO to 8 port passive breakout module"
PID: NCS1K-BRK-8       , VID: V00 , SN: MPM25401003

NAME: "0/1/2", DESCR: "NCS 1000 MTP/MPO to 24 colorless chs passive breakout module"
PID: NCS1K-BRK-24      , VID: V00 , SN: MPM25141004

NAME: "0/1/3", DESCR: "NCS 1000 MTP/MPO to 24 colorless chs passive breakout module"
PID: NCS1K-BRK-24      , VID: V00 , SN: MPM25371005

NAME: "0/2", DESCR: "NCS 1000 32 chs Even Mux/Demux Patch Panel - 150GHz - C-band"
PID: NCS1K-MD-32E-C    , VID: V00 , SN: ACW2529YE13

NAME: "0/3", DESCR: "NCS 1000 32 chs Odd  Mux/Demux Patch Panel - 150GHz - C-band"
PID: NCS1K-MD-32O-C    , VID: V00 , SN: ACW2529YA13

NAME: "0/FT0", DESCR: "NCS1010 - Shelf Fan"
PID: NCS1010-FAN       , VID: V00, SN: FCB2504B0W3

NAME: "0/FT1", DESCR: "NCS1010 - Shelf Fan"
PID: NCS1010-FAN       , VID: V00, SN: FCB2504B0U8

NAME: "0/PM0", DESCR: "NCS 1010 - AC Power Supply Unit" 
PID: NCS1010-AC-PSU    , VID: V00, SN: APS244700D0

NAME: "0/PM1", DESCR: "NCS 1010 - AC Power Supply Unit"
PID: NCS1010-AC-PSU    , VID: V00, SN: APS244700BY

Verify Software Version

NCS 1010 is shipped with the Cisco IOS XR software preinstalled. Verify that the latest version of the software is installed. If a newer version is available, perform a Upgrade Software. This software upgrade installs the newer version of the software and provide the latest feature set on NCS 1010.

To verify the version of Cisco IOS XR Software running on NCS 1010, perform the following procedure.

Procedure


show version

Displays the software version and details such as system uptime.

Example:

RP/0/RP0/CPU0:ios#show version
Sat Mar 25 11:38:23.614 IST
Cisco IOS XR Software, Version 7.9.1
Copyright (c) 2013-2023 by Cisco Systems, Inc.
Build Information:
Built By : ingunawa
Built On : Tue Mar 07 02:22:55 UTC 2023
Build Host : iox-ucs-063
Workspace : /auto/iox-ucs-063-san2/prod/7.9.1.30I.SIT_IMAGE/ncs1010/ws
Version : 7.9.1
Label : 7.9.1
cisco NCS1010 (C3758 @ 2.20GHz)
cisco NCS1010-SA (C3758 @ 2.20GHz) processor with 32GB of memory
OLT-C-R-SITE-1 uptime is 2 weeks, 12 hours, 59 minutes
NCS 1010 - Chassis

Verify the software version to determine whether system upgrade is required. If the upgrade is required, see Upgrade Software.


Verify Firmware Version

The firmware version on various hardware components of NCS 1010 must be compatible with the installed Cisco IOS XR release. Incompatibility may cause NCS 1010 to malfunction.

To verify the firmware version, perform the following procedure.

Procedure


Step 1

show hw-module fpd

Displays the firmware information of various hardware components of NCS 1010.

Example:

RP/0/RP0/CPU0:ios#show hw-module fpd
Thu Mar  2 12:35:06.602 IST

Auto-upgrade:Enabled
Attribute codes: B golden, P protect, S secure, A Anti Theft aware
                                                                         FPD Versions
                                                                        ==============
Location   Card type             HWver FPD device       ATR Status   Running Programd  Reload Loc
-------------------------------------------------------------------------------------------------
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  ADMConfig            CURRENT    3.40    3.40       NOT REQ
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  BIOS             S   CURRENT    4.20    4.20         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  BIOS-Golden      BS  CURRENT            4.10         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  CpuFpga          S   CURRENT    1.11    1.11         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  CpuFpgaGolden    BS  CURRENT            1.01         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  SsdIntelS4510    S   CURRENT   11.32   11.32         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  TamFw            S   CURRENT    6.13    6.13         0/RP0
0/RP0/CPU0 NCS1010-CNTLR-K9      1.11  TamFwGolden      BS  CURRENT            6.11         0/RP0
0/PM0      NCS1010-AC-PSU        0.0   AP-PriMCU            CURRENT    1.03    1.03       NOT REQ
0/PM0      NCS1010-AC-PSU        0.0   AP-SecMCU            CURRENT    2.01    2.01       NOT REQ
0/PM1      NCS1010-AC-PSU        0.0   AP-PriMCU            CURRENT    1.03    1.03       NOT REQ
0/PM1      NCS1010-AC-PSU        0.0   AP-SecMCU            CURRENT    2.01    2.01       NOT REQ
0/0/NXR0   NCS1K-OLT-L           1.0   OLT              S   CURRENT    1.02    1.02       NOT REQ
0/Rack     NCS1010-SA            2.1   EITU-ADMConfig       CURRENT    2.10    2.10       NOT REQ
0/Rack     NCS1010-SA            2.1   IoFpga           S   CURRENT    1.12    1.12       NOT REQ
0/Rack     NCS1010-SA            2.1   IoFpgaGolden     BS  CURRENT            1.01       NOT REQ
0/Rack     NCS1010-SA            2.1   SsdIntelS4510    S   CURRENT   11.32   11.32        0/Rack

Step 2

show fpd package

Displays the FPD image version available with this software release for each hardware component.

Example:

RP/0/RP0/CPU0:ios#show fpd package
Thu Mar  2 12:37:58.530 IST
 
=============================== ================================================
                                        Field Programmable Device Package
                                ================================================
                                               Req     SW      Min Req   Min Req
Card Type            FPD Description           Reload  Ver     SW Ver  Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
NCS1010-AC-PSU       AP-PriMCU                  NO      1.03      1.03      0.0 
                     AP-SecMCU                  NO      2.01      2.01      0.0 
--------------------------------------------------------------------------------
NCS1010-CNTLR-K9     ADMConfig                  NO      2.30      2.30      0.0 
                     ADMConfig                  NO      2.30      2.30      0.0 
                     ADMConfig                  NO      3.40      3.40      1.0 
                     BIOS                       YES     4.20      4.20      0.0 
                     BIOS                       YES     4.20      4.20      0.0 
                     BIOS-Golden                YES     4.10      4.10      0.0 
                     BIOS-Golden                YES     4.10      4.10      0.0 
                     CpuFpga                    YES     1.11      1.11      0.0 
                     CpuFpga                    YES     1.11      1.11      0.0 
                     CpuFpgaGolden              YES     1.01      1.01      0.0 
                     CpuFpgaGolden              YES     1.01      1.01      0.0 
                     SsdIntelS4510              YES    11.32     11.32      0.0 
                     SsdIntelS4510              YES    11.32     11.32      0.0 
                     SsdMicron5300              YES     0.01      0.01      0.0 
                     SsdMicron5300              YES     0.01      0.01      0.0 
                     SsdSmartModular            YES    13.06     13.06      0.0 
                     SsdSmartModular            YES    13.06     13.06      0.0 
                     TamFw                      YES     6.13      6.13      0.0 
                     TamFw                      YES     6.13      6.13      0.0 
                     TamFwGolden                YES     6.11      6.11      0.0 
                     TamFwGolden                YES     6.11      6.11      0.0 
--------------------------------------------------------------------------------
NCS1010-SA           EITU-ADMConfig             NO      1.04      1.04      0.0 
                     EITU-ADMConfig             NO      2.10      2.10      1.0 
                     EITU-ADMConfig             NO      1.04      1.04      0.0 
                     EITU-ADMConfig             NO      2.10      2.10      1.0 
                     IoFpga                     NO      1.12      1.12      0.0 
                     IoFpga                     NO      1.12      1.12      0.0 
                     IoFpgaGolden               NO      1.01      1.01      0.0 
                     IoFpgaGolden               NO      1.01      1.01      0.0 
                     SsdIntelS4510              YES    11.32     11.32      0.0 
                     SsdIntelS4510              YES    11.32     11.32      0.0 
                     SsdMicron5300              YES     0.01      0.01      0.0 
                     SsdMicron5300              YES     0.01      0.01      0.0 
                     SsdSmartModular            YES    13.06     13.06      0.0 
                     SsdSmartModular            YES    13.06     13.06      0.0 
--------------------------------------------------------------------------------
NCS1K-ILA-2R-C       ILA                        NO      1.12      1.12      0.1 
                     ILA                        NO      0.28      0.28     99.1 
                     Raman-1                    NO      1.04      1.04      0.1 
                     Raman-1                    NO      0.28      0.28     99.1 
                     Raman-2                    NO      1.04      1.04      0.1 
                     Raman-2                    NO      0.28      0.28     99.1 
--------------------------------------------------------------------------------
NCS1K-ILA-C          ILA                        NO      1.12      1.12      0.1 
                     ILA                        NO      0.28      0.28     99.1 
--------------------------------------------------------------------------------
NCS1K-ILA-L          ILA                        NO      1.00      1.00      0.1 
--------------------------------------------------------------------------------
NCS1K-ILA-R-C        ILA                        NO      1.12      1.12      0.1 
                     ILA                        NO      0.28      0.28     99.1 
                     Raman-1                    NO      1.04      1.04      0.1 
                     Raman-1                    NO      0.28      0.28     99.1 
--------------------------------------------------------------------------------
NCS1K-OLT-C          OLT                        NO      1.12      1.12      0.1 
                     OLT                        NO      0.28      0.28     99.1 
--------------------------------------------------------------------------------
NCS1K-OLT-L          OLT                        NO      1.02      1.02      0.1 
--------------------------------------------------------------------------------
NCS1K-OLT-R-C        OLT                        NO      1.12      1.12      0.1 
                     OLT                        NO      0.28      0.28     99.1 
                     Raman-1                    NO      1.04      1.04      0.1 
                     Raman-1                    NO      0.28      0.28     99.1 

Verify Management Interface Status

To verify the management interface status, perform the following procedure.

Procedure


Step 1

show interfaces MgmtEth 0/RP0/CPU0/0

Displays the management interface configuration.

Example:

RP/0/RP0/CPU0:ios#show interfaces MgmtEth 0/RP0/CPU0/0
Wed May 25 11:49:18.118 UTC
MgmtEth0/RP0/CPU0/0 is up, line protocol is up 
  Interface state transitions: 1
  Hardware is Management Ethernet, address is 38fd.f866.0964 (bia 38fd.f866.0964)
  Internet address is 10.33.0.61/16
  MTU 1514 bytes, BW 1000000 Kbit (Max: 1000000 Kbit)
     reliability 255/255, txload 0/255, rxload 0/255
  Encapsulation ARPA,
  Full-duplex, 1000Mb/s, CX, link type is autonegotiation
  loopback not set,
  Last link flapped 15:05:21
  ARP type ARPA, ARP timeout 04:00:00
  Last input never, output 00:00:00
  Last clearing of "show interface" counters never
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     53138 packets input, 6636701 bytes, 0 total input drops
     0 drops for unrecognized upper-level protocol
     Received 12145 broadcast packets, 40082 multicast packets
              0 runts, 0 giants, 0 throttles, 0 parity
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     217288 packets output, 60964220 bytes, 0 total output drops
     Output 1 broadcast packets, 15 multicast packets
     0 output errors, 0 underruns, 0 applique, 0 resets
     0 output buffer failures, 0 output buffers swapped out
     1 carrier transitions

Step 2

show interfaces summary and show interfaces brief

Verifies the management interface status.

Example:

RP/0/RP0/CPU0:ios#show interfaces summary
Wed May 25 11:50:02.558 UTC
Interface Type          Total    UP       Down     Admin Down
--------------          -----    --       ----     ----------   
ALL TYPES                9        5         0          4       
--------------         
IFT_GETHERNET           1        1          0          0       
IFT_LOOPBACK            2        2          0          0       
IFT_ETHERNET            3        1          0          2       
IFT_NULL                1        1          0          0       
IFT_PTP_ETHERNET        2        0          0          2       

Example:

RP/0/RP0/CPU0:ios#show interfaces brief
Wed May 25 11:50:28.438 UTC

               Intf     Intf        LineP              Encap         MTU        BW
               Name    State       State               Type        (byte)    (Kbps)
--------------------------------------------------------------------------------------------------------
                Lo0       up          up              Loopback       1500          0
                Lo3       up          up              Loopback       1500          0
                Nu0       up          up               Null           1500          0
          Gi0/0/0/0       up          up               ARPA           1514    1000000
         Mg0/RP0/CPU0/0    up          up               ARPA          1514    1000000
        Mg0/RP0/CPU0/1    admin-down  admin-down        ARPA  1514    1000000
        Mg0/RP0/CPU0/2    admin-down  admin-down        ARPA  1514    1000000
        PT0/RP0/CPU0/0    admin-down  admin-down        ARPA  1514    1000000
        PT0/RP0/CPU0/1    admin-down  admin-down        ARPA  1514    1000000


Example:

RP/0/RP0/CPU0:ios#show ipv4 interfaces brief
Tue Jul 12 07:32:42.390 UTC

Interface                      IP-Address      Status          Protocol Vrf-Name
Loopback0                      10.3.3.21        Up              Up       default 
Loopback3                      10.1.1.2        Up              Up       default 
GigabitEthernet0/0/0/0         10.7.1.20        Up              Up       default 
MgmtEth0/RP0/CPU0/0            10.4.33.63       Up              Up       default 
PTP0/RP0/CPU0/0                unassigned      Shutdown        Down     default 
MgmtEth0/RP0/CPU0/1            unassigned      Down            Down     default 
PTP0/RP0/CPU0/1                unassigned      Shutdown        Down     default 
MgmtEth0/RP0/CPU0/2            unassigned      Down            Down     default 

Verify Alarms

You can view the alarm information using the show alarms command.

Procedure


show alarms [ brief [ card | rack | system ] [ location location ] [ active | history ] | detail [ card | rack | system ] [ location location ] [ active | clients | history | stats ] ]

Displays alarms in brief or detail.

Example:

RP/0/RP0/CPU0:ios#show alarms brief system active
 
Thu Apr 28 06:16:50.524 UTC

------------------------------------------------------------------------------------
Active Alarms 
------------------------------------------------------------------------------------
Location        Severity     Group            Set Time                   Description
------------------------------------------------------------------------------------
0/RP0/CPU0      Major        Ethernet         04/28/2022 06:03:39 UTC    RP-SW: SPI flash config is incorrect
0/PM0           Major        Environ          04/28/2022 06:03:50 UTC    Power Module Error (PM_VIN_VOLT_OOR)
0/PM0           Major        Environ          04/28/2022 06:03:50 UTC    Power Module Output Disabled (PM_OUTPUT_DISABLED)
0               Major        Environ          04/28/2022 06:03:50 UTC    Power Group redundancy lost
0/PM0           Major        FPD_Infra        04/28/2022 06:04:08 UTC    One Or More FPDs Need Upgrade Or Not In Current State
0/PM1           Major        FPD_Infra        04/28/2022 06:04:09 UTC    One Or More FPDs Need Upgrade Or Not In Current State
0/0             Minor        Environ          04/28/2022 06:04:10 UTC    ILAC_CT_1: Invalid sensor read error.
0/0             Minor        Environ          04/28/2022 06:04:10 UTC    ILAC_CT_2: Invalid sensor read error.
0/0             Minor        Environ          04/28/2022 06:04:10 UTC    ILAC_CT_3: Invalid sensor read error.
0/0             Minor        Environ          04/28/2022 06:04:10 UTC    ILAC_CT_4: Invalid sensor read error.
0/0             Major        Controller       04/28/2022 06:05:12 UTC    Osc0/0/0/0 - Provisioning Failed     
0/0             Major        Controller       04/28/2022 06:05:12 UTC    Osc0/0/0/2 - Provisioning Failed     
0/0             Major        Controller       04/28/2022 06:05:12 UTC    Ots0/0/0/0 - Provisioning Failed     
0/0             Major        Controller       04/28/2022 06:05:12 UTC    Ots0/0/0/2 - Provisioning Failed     

Note

 
In the maintenance mode, all the alarms are moved from active to suppressed and the show alarms command does not display the alarms details.

Verify Environmental Parameters

The show environment command displays the environmental parameters of NCS 1010.

To verify that the environmental parameters are as expected, perform the following procedure.

Procedure


show environment [ alarm-contact| all | altitude| current | fan| humidity | power | voltages[ location | location ] | temperature[ location | location ] ]

Displays the environmental parameters of NCS 1010.

Example:

The following example shows a sample output of the show environment command with the fan keyword.

RP/0/RP0/CPU0:ios#show environment fan
Thu May 26 04:15:37.765 UTC
===========================================================================
                                              Fan speed (rpm)
Location      FRU Type                        FAN_0    FAN_1   FAN_2   
---------------------------------------------------------------------------

0/PM0        NCS1010-AC-PSU                     5368   
0/PM1        NCS1010-AC-PSU                     5336   
0/FT0        NCS1010-FAN                       10020   10020   10020   
0/FT1        NCS1010-FAN                       10020   10020    9960   

==============================================================================

The following example shows a sample output of the show environment command with the temperatures keyword for 0/RP0 location.

RP/0/RP0/CPU0:ios#show environment temperature location 0/RP0
 
Thu May 26 04:16:39.832 UTC
=============================================================================================================
Location  TEMPERATURE                          Value     Crit    Major    Minor    Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)     (Hi)     (Hi)    (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_TEMP_PCB                            30      -10       -5        0       70       75       80
          RP_TEMP_HOT_SPOT                       33      -10       -5        0       70       75       80
          RP_TEMP_LTM4638                        49      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_0                      36      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_1                      39      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCCP_TMON                  33      -10       -5        0       80       85       90
          RP_JMAC_1V0_VNN_TMON                   33      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCC_RAM_TMON               32      -10       -5        0       80       85       90
          RP_JMAC_1V2_DDR_VDDQ_TMON              33      -10       -5        0       80       85       90
==============================================================================================================

The following example shows a sample output of the show environment command with the temperatures keyword for 0/0/NXR0 location.

RP/0/RP0/CPU0:ios#show environment temperature location 0/0/NXR0 

Thu May 26 04:16:39.832 UTC
=============================================================================================================
Location  TEMPERATURE                          Value     Crit    Major    Minor    Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)     (Hi)     (Hi)    (Hi)
-------------------------------------------------------------------------------------------------------------
0/0/NXR0   
          OLTC_LT_P0_iEDFA0                      24       18       19       20       30       31       32
          OLTC_LT_P0_iEDFA1                      25       18       19       20       30       31       32
          OLTC_LT_P0_iEDFA2                      24       18       19       20       30       31       32
          OLTC_LT_P2_iEDFA0                      25       18       19       20       30       31       32
          OLTC_LT_P3_iEDFA0                      25       18       19       20       30       31       32
          OLTC_LT_P0_eEDFA0                      24       18       19       20       30       31       32
          OLTC_CT_1                              32      -10       -7       -5       75       77       80
          OLTC_LT_P0_eEDFA1                      24       18       19       20       30       31       32
          OLTC_CT_2                              27      -10       -7       -5       70       73       75
          OLTC_CT_3                              30      -10       -7       -5       70       73       75
          OLTC_CT_4                              30      -10       -7       -5       70       73       75
          OLTC_FT_P0_iEDFA0                      60       55       57       58       62       64       65
          OLTC_FT_P2_iEDFA0                      60       55       57       58       62       64       65
          OLTC_FT_P3_iEDFA0                      60       55       57       58       62       64       65
          OLTC_FT_P0_eEDFA0                      60       55       57       58       62       64       65
=============================================================================================================

The following example shows a sample output of the show environment command with the power keyword.

RP/0/RP0/CPU0:ios#show environment power
Thu May 26 04:17:55.592 UTC
================================================================================
CHASSIS LEVEL POWER INFO: 0
================================================================================
   Total output power capacity (Group 0 + Group 1) :    1050W +     1050W
   Total output power required                     :     700W
   Total power input                               :     228W
   Total power output                              :     140W

Power Group 0:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM0       NCS1010-AC-PSU  228.5     0.5     12.1      5.6      OK

Total of Group 0:              114W/0.5A         67W/5.6A

Power Group 1:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM1       NCS1010-AC-PSU  228.5     0.5     12.1      6.1      OK
          
Total of Group 1:              114W/0.5A         73W/6.1A
          
================================================================================
   Location     Card Type               Power       Power        Status
                                        Allocated   Used
                                        Watts       Watts
================================================================================
   0/RP0/CPU0   NCS1010-CNTLR-K9        90          14           ON
   0/FT0        NCS1010-FAN             110         17           ON
   0/FT1        NCS1010-FAN             110         15           ON
   0/0/NXR0     NCS1K-OLT-C             350         61           ON
   0/Rack       NCS1010-SA              40          19           ON


=================================================================================

The following example shows a sample output of the show environment command with the voltages keyword.

RP/0/RP0/CPU0:ios#show environment voltage location 0/RP0 
Thu May 26 04:19:16.636 UTC
========================================================================================
Location  VOLTAGE                             Value      Crit    Minor    Minor     Crit
          Sensor                              (mV)       (Lo)    (Lo)     (Hi)      (Hi)
----------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_ADM1266_12V0                     12094    10800    11280    12720    13200
          RP_ADM1266_1V8_CPU                   1806     1670     1750     1850     1930
          RP_ADM1266_1V24_VCCREF               1238     1150     1200     1280     1330
          RP_ADM1266_1V05_CPU                  1047      980     1020     1080     1120
          RP_ADM1266_1V2_DDR_VDDQ              1204     1120     1160     1240     1280
          RP_ADM1266_1V0_VCC_RAM                988      650      700     1250     1300
          RP_ADM1266_1V0_VNN                    869      550      600     1250     1300
          RP_ADM1266_1V0_VCCP                  1018      450      500     1250     1300
          RP_ADM1266_0V6_DDR_VTT                599      560      580      620      640
          RP_ADM1266_3V3_STAND_BY              3301     3070     3200     3400     3530
          RP_ADM1266_5V0                       5004     4650     4850     5150     5350
          RP_ADM1266_3V3                       3325     3070     3200     3400     3530
          RP_ADM1266_2V5_PLL                   2489     2330     2430     2580     2680
          RP_ADM1266_2V5_FPGA                  2502     2330     2430     2580     2680
          RP_ADM1266_1V2_FPGA                  1202     1120     1160     1240     1280
          RP_ADM1266_3V3_CPU                   3332     3070     3200     3400     3530
          RP_ADM1266_2V5_CPU                   2498     2330     2430     2580     2680

=========================================================================================

The following example shows a sample output of the show environment command with the current keyword.

RP/0/RP0/CPU0:P2C_DT_02#show environment current 
Tue Jul  5 08:36:22.132 UTC
==========================================================================================
Location  CURRENT                              Value    
          Sensor                               (mA)    
------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_CURRMON_LTM4638                    395
          RP_CURRMON_LTM4644_0                  179
          RP_CURRMON_LTM4644_1                  307
          RP_JMAC_1V0_VCCP_IMON                 187
          RP_JMAC_1V0_VNN_IMON                   62
          RP_JMAC_1V0_VCC_RAM_IMON                0
          RP_JMAC_1V2_DDR_VDDQ_IMON             187
0/Rack     
          SA_ADM1275_12V_MOD0_IMON             4154
          SA_ADM1275_12V_MOD1_IMON               43
          SA_ADM1275_12V_MOD2_IMON               18
          SA_ADM1275_12V_FAN0_IMON             1356
          SA_ADM1275_12V_FAN1_IMON             1517
          SA_INA230_5V0_IMON                    129
          SA_INA230_3V3_IMON                   2998
          SA_INA230_1V0_XGE_CORE_IMON          2464
          SA_INA230_1V0_FPGA_CORE_IMON          787
          SA_ADM1275_12V_SA_IMON               1668
          SA_ADM1275_12V_CPU_IMON              1147

The following example shows a sample output of the show environment command with the altitude keyword.

RP/0/RP0/CPU0:P2C_DT_02#show environment altitude 
Tue Jul  5 08:36:51.710 UTC
================================================================================
Location     Altitude Value (Meters)    Source         
--------------------------------------------------------------------------------
0            760                    sensor

The following example shows a sample output of the show environment command with the all keyword.

RP/0/RP0/CPU0:P2C_DT_02#show environment all

Tue Jul  5 08:37:28.412 UTC
=============================================================================================================
Location  TEMPERATURE                          Value     Crit    Major    Minor    Minor    Major    Crit
          Sensor                             (deg C)     (Lo)     (Lo)     (Lo)     (Hi)     (Hi)    (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_TEMP_PCB                            29      -10       -5        0       70       75       80
          RP_TEMP_HOT_SPOT                       32      -10       -5        0       70       75       80
          RP_TEMP_LTM4638                        45      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_0                      35      -10       -5        0       80       85       90
          RP_TEMP_LTM4644_1                      38      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCCP_TMON                  30      -10       -5        0       80       85       90
          RP_JMAC_1V0_VNN_TMON                   29      -10       -5        0       80       85       90
          RP_JMAC_1V0_VCC_RAM_TMON               30      -10       -5        0       80       85       90
          RP_JMAC_1V2_DDR_VDDQ_TMON              31      -10       -5        0       80       85       90
0/PM0      
          Ambient Temp                           29      -10       -5        0       55       60       65
          Secondary HotSpot Temp                 50      -10       -5        0       85       90       95
          Primary HotSpot Temp                   41      -10       -5        0       65       70       75
0/0/NXR0   
          ILAC_LT_P0_eEDFA0                      25       18       19       20       30       31       32
          ILAC_LT_P0_eEDFA1                      25       18       19       20       30       31       32
          ILAC_LT_P0_eEDFA2                      25       18       19       20       30       31       32
          ILAC_LT_P2_eEDFA0                      25       18       19       20       30       31       32
          ILAC_LT_P2_eEDFA1                      25       18       19       20       30       31       32
          ILAC_LT_P2_eEDFA2                      25       18       19       20       30       31       32
          ILAC_CT_1                              29      -10       -7       -5       75       77       80
          ILAC_CT_2                              26      -10       -7       -5       70       73       75
          ILAC_CT_3                              28      -10       -7       -5       70       73       75
          ILAC_CT_4                              28      -10       -7       -5       70       73       75
          ILAC_FT_P0_eEDFA0                      59       55       57       58       62       64       65
          ILAC_FT_P0_eEDFA1                      59       55       57       58       62       64       65
0/Rack     
          SA_TEMP_AIR_INLET0                     25      -10       -5        0       45       55       60
          SA_TEMP_AIR_INLET1                     25      -10       -5        0       45       55       60
          SA_TEMP_AIR_EXAUST0                    27      -10       -5        0       75       85       90
          SA_TEMP_AIR_EXAUST1                    26      -10       -5        0       75       85       90
          SA_TEMP_PCB_HOT_SPOT0                  28      -10       -5        0       80       85       90
          SA_TEMP_PCB_HOT_SPOT1                  32      -10       -5        0       80       85       90
          SA_TEMP_PCB_HOT_SPOT2                  28      -10       -5        0       80       85       90
          SA_TEMP_PCB_HOT_SPOT3                  30      -10       -5        0       80       85       90

=============================================================================================================
Location  VOLTAGE                             Value      Crit    Minor    Minor     Crit
          Sensor                              (mV)       (Lo)    (Lo)     (Hi)      (Hi)
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_ADM1266_12V0                     12094    10800    11280    12720    13200
          RP_ADM1266_1V8_CPU                   1801     1670     1750     1850     1930
          RP_ADM1266_1V24_VCCREF               1238     1150     1200     1280     1330
          RP_ADM1266_1V05_CPU                  1054      980     1020     1080     1120
          RP_ADM1266_1V2_DDR_VDDQ              1207     1120     1160     1240     1280
          RP_ADM1266_1V0_VCC_RAM                988      650      700     1250     1300
          RP_ADM1266_1V0_VNN                    858      550      600     1250     1300
          RP_ADM1266_1V0_VCCP                  1008      450      500     1250     1300
          RP_ADM1266_0V6_DDR_VTT                603      560      580      620      640
          RP_ADM1266_3V3_STAND_BY              3310     3070     3200     3400     3530
          RP_ADM1266_5V0                       4996     4650     4850     5150     5350
          RP_ADM1266_3V3                       3328     3070     3200     3400     3530
          RP_ADM1266_2V5_PLL                   2489     2330     2430     2580     2680
          RP_ADM1266_2V5_FPGA                  2500     2330     2430     2580     2680
          RP_ADM1266_1V2_FPGA                  1197     1120     1160     1240     1280
          RP_ADM1266_3V3_CPU                   3332     3070     3200     3400     3530
          RP_ADM1266_2V5_CPU                   2502     2330     2430     2580     2680
0/Rack     
          SA_ADM1266_12V_BUS_EITU             12057    10800    11280    12720    13200
          SA_ADM1266_5V0                       5022     4650     4800     5200     5350
          SA_ADM1266_1V8_ZARLINK_DPLL          1806     1670     1730     1870     1930
          SA_ADM1266_1V0_PHY                   1009      930      960     1040     1070
          SA_ADM1266_1V0_ALDRIN_CORE            982      910      930     1070     1090
          SA_ADM1266_1V0_ALDRIN_SERDES         1007      930      960     1040     1070
          SA_ADM1266_1V0_FPGA                  1008      930      960     1040     1070
          SA_ADM1266_1V2_FPGA                  1205     1120     1150     1250     1280
          SA_ADM1266_1V8                       1804     1670     1730     1870     1930
          SA_ADM1266_2V5                       2505     2330     2400     2600     2680
          SA_ADM1266_3V3                       3323     3070     3170     3430     3530
          SA_ADM1275_12V_SA_BP                12058    10800    11280    12720    13200
          SA_ADM1275_12V_CPU_BP               12032    10800    11280    12720    13200
          SA_ADM1275_12V_MOD0_BP              12063    10800    11280    12720    13200
          SA_ADM1275_12V_MOD1_BP              12048    10800    11280    12720    13200
          SA_ADM1275_12V_MOD2_BP              12027    10800    11280    12720    13200
          SA_ADM1275_12V_FAN0_BP              12032    10800    11280    12720    13200
          SA_ADM1275_12V_FAN1_BP              12042    10800    11280    12720    13200
=============================================================================================================
Location  CURRENT                              Value    
          Sensor                               (mA)    
-------------------------------------------------------------------------------------------------------------
0/RP0/CPU0 
          RP_CURRMON_LTM4638                    395
          RP_CURRMON_LTM4644_0                  179
          RP_CURRMON_LTM4644_1                  307
          RP_JMAC_1V0_VCCP_IMON                 125
          RP_JMAC_1V0_VNN_IMON                   62
          RP_JMAC_1V0_VCC_RAM_IMON                0
          RP_JMAC_1V2_DDR_VDDQ_IMON             156
0/Rack     
          SA_ADM1275_12V_MOD0_IMON             3412
          SA_ADM1275_12V_MOD1_IMON               30
          SA_ADM1275_12V_MOD2_IMON               43
          SA_ADM1275_12V_FAN0_IMON             1418
          SA_ADM1275_12V_FAN1_IMON             1394
          SA_INA230_5V0_IMON                    129
          SA_INA230_3V3_IMON                   3020
          SA_INA230_1V0_XGE_CORE_IMON          2464
          SA_INA230_1V0_FPGA_CORE_IMON          787
          SA_ADM1275_12V_SA_IMON               1640
          SA_ADM1275_12V_CPU_IMON              1157
===========================================================================
                                              Fan speed (rpm)
Location      FRU Type                        FAN_0    FAN_1   FAN_2   
---------------------------------------------------------------------------

0/PM0        NCS1010-AC-PSU                     5424   
0/FT0        NCS1010-FAN                        9960    9960    9960   
0/FT1        NCS1010-FAN                       10020   10020   10020   
================================================================================
Location     Altitude Value (Meters)    Source         
--------------------------------------------------------------------------------
0            760                    sensor

================================================================================
CHASSIS LEVEL POWER INFO: 0
================================================================================
   Total output power capacity (Group 0 + Group 1) :    1050W +        0W
   Total output power required                     :     700W
   Total power input                               :     159W
   Total power output                              :     129W

Power Group 0:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM1       NCS1010-AC-PSU  0.0       0.0     0.0       0.0      OFFLINE

Total of Group 0:                0W/0.0A         0W/0.0A

Power Group 1:
================================================================================
   Power       Supply         ------Input----   ------Output---     Status
   Module      Type            Volts     Amps    Volts     Amps    
================================================================================
   0/PM0       NCS1010-AC-PSU  228.5     0.7     12.1      10.7     OK

Total of Group 1:              159W/0.7A         129W/10.7A

================================================================================
   Location     Card Type               Power       Power        Status
                                        Allocated   Used
                                        Watts       Watts
================================================================================
   0/RP0/CPU0   NCS1010-CNTLR-K9        90          14           ON
   0/FT0        NCS1010-FAN             110         17           ON
   0/FT1        NCS1010-FAN             110         16           ON
   0/0/NXR0     NCS1K-ILA-C             350         54           ON
   0/Rack       NCS1010-SA              40          19           ON

Environment parameter anomalies are logged in the syslog. As a result, if an environment parameter that is displayed in the show environment command output is not as expected, check the syslog using the show logging and show alarms brief system active command. The syslog provides details on any logged problems.


Verify Context

The show context command displays core dump context information of NCS 1010. Core dump is a result of abnormal exit of any process running in the system.

Procedure


show context

Displays the core dump context information of NCS 1010.

Example:

RP/0/RP0/CPU0:ios# show context
Mon Sep 27 17:21:59.219 UTC

node: node0_RP0_CPU0
----------------------------------------------------------------
No context

The command output is empty during system upgrade.


Verify Core Files

Use the run command to go to the hard disk location and check for the core dumps of NCS 1010.

Procedure


run

Example:

RP/0/RP0/CPU0:ios# run
Mon Sep 27 17:29:11.163 UTC
[xr-vm_node0_RP0_CPU0:~]$cd /misc/disk1/
[xr-vm_node0_RP0_CPU0:/misc/disk1]$ls -lrt *.tgz

Verify Memory Information

You can view the memory information using the show watchdog memory-state command.

Procedure


show watchdog memory-state location all

Displays memory snapshot in brief.

Example:

RP/0/RP0/CPU0:ios#show watchdog memory-state location all
Thu Jun 16 08:36:44.436 UTC
---- node0_RP0_CPU0 ----
Memory information:
    Physical Memory     : 31935.167 MB
    Free Memory         : 29236.0   MB
    Memory State        :   Normal