- About this Guide
- Chapter 1, Install the Shelf and Backplane Cable
- Chapter 2, Install Cards and Fiber-Optic Cable
- Chapter 3, Connect the PC and Log Into the GUI
- Chapter 4, Turn Up a Node
- Chapter 5, Turn Up a Network
- Chapter 6, Create Circuits and VT Tunnels
- Chapter 7, Manage Circuits
- Chapter 8, Manage Alarms
- Chapter 9, Monitor Performance
- Chapter 10, Change Card Settings
- Chapter 11, Change Node Settings
- Chapter 12, Upgrade Cards and Spans
- Chapter 13, Convert Network Configurations
- Chapter 14, Add and Remove Nodes
- Chapter 15, Maintain the Node
- Chapter 16, Power Down the Node
- Chapter 17, DLPs A1 to A99
- Chapter 18, DLPs A100 to A199
- Chapter 19, DLPs A200 to A299
- Chapter 20, DLPs A300 to A399
- Chapter 21, DLPs A400 to A499
- Chapter 22, DLPs A500 to A599
- Chapter 23, DLPs A600 to A699
- Appendix A, CTC Information and Shortcuts
- Before You Begin
- NTP-A81 Change Node Management Information
- NTP-A201 Change CTC Network Access
- NTP-A319 Modify OSI Provisioning
- NTP-A202 Customize the CTC Network View
- NTP-A203 Modify or Delete Card Protection Settings
- NTP-A292 Modify or Delete Communications Channel Terminations and Provisionable Patchcords
- NTP-A85 Change Node Timing
- NTP-A205 Modify Users and Change Security
- NTP-A87 Change SNMP Settings
Change Node Settings
Note The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This chapter explains how to modify node provisioning for the Cisco ONS 15454. To provision a new node, see Chapter 4 "Turn Up a Node." To change default network element settings and to view a list of those settings, refer to the "Network Element Defaults" appendix in the Cisco ONS 15454 Reference Manual.
Before You Begin
Before performing the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15454 Troubleshooting Guide as necessary.
This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs).
1. A81 Change Node Management Information—Complete this procedure as needed to change node name, contact information, latitude, longitude, date, time, and login legal disclaimer.
2. A201 Change CTC Network Access—Complete this procedure as needed to change the IP address, default router, subnet mask, network configuration settings, and static routes.
3. A319 Modify OSI Provisioning—Complete this procedure as needed to modify Open System Interconnection (OSI) parameters including the OSI routing mode, Target Identifier Address Resolution Protocol (TARP), routers, subnets, and IP over OSI tunnels.
4. A202 Customize the CTC Network View—As needed, complete this procedure to create domains and customize the appearance of the network map, including specifying a different default map, creating domains, selecting your own map or image, consolidating links, toggling global and local domain settings, and changing the background color.
5. A203 Modify or Delete Card Protection Settings—Complete as needed.
6. A292 Modify or Delete Communications Channel Terminations and Provisionable Patchcords—Complete this procedure as needed to modify or delete Section DCC (SDCC) or Line DCC (LDCC) terminations or provisionable patchcords.
7. A85 Change Node Timing—Complete as needed.
8. A205 Modify Users and Change Security—Complete this procedure as needed to make changes to user settings, including security level and security policies, to change Remote Authentication Dial In User Service (RADIUS) server settings, and to delete users.
9. A87 Change SNMP Settings—Complete as needed.
NTP-A81 Change Node Management Information
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 Complete the "DLP-A140 Change the Node Name, Date, Time, and Contact Information" task, as needed.
Step 4 Complete the "DLP-A265 Change the Login Legal Disclaimer" task, as needed.
Step 5 After confirming the changes, complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-A201 Change CTC Network Access
Note Additional ONS 15454 networking information and procedures, including IP addressing examples, static route scenarios, OSPF protocol, and Routing Information Protocol (RIP) options are provided in the Cisco ONS 15454 Reference Manual.
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•A250 Set Up or Change Open Shortest Path First Protocol
•A383 Delete a Firewall Tunnel
•A435 Modify Backplane Port IP Settings
•A436 Disable Node Security Mode
Step 4 Complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-A319 Modify OSI Provisioning
Note Additional information about the ONS 15454 implementation of OSI is provided in the "Management Network Connectivity" chapter of the Cisco ONS 15454 Reference Manual.
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•A535 Provision or Modify TARP Operating Parameters
•A536 Add a Static TID to NSAP Entry to the TARP Data Cache
•A537 Remove a Static TID to NSAP Entry from the TARP Data Cache
•A538 Add a TARP Manual Adjacency Table Entry
•A543 Remove a TARP Manual Adjacency Table Entry
•A544 Change the OSI Routing Mode
•A545 Edit the OSI Router Configuration
•A546 Edit the OSI Subnetwork Point of Attachment
•A547 Edit an IP-Over-CLNS Tunnel
•A548 Delete an IP-Over-CLNS Tunnel
Step 4 Complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-A202 Customize the CTC Network View
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the following tasks, as needed:
•A145 Change the Network View Background Color
•A528 Change the Default Network View Background Map
•A268 Apply a Custom Network View Background Map
•A269 Enable Dialog Box Do-Not-Display Option
•A498 Switch Between TDM and DWDM Network Views
•A495 Consolidate Links in Network View
Stop. You have completed this procedure.
NTP-A203 Modify or Delete Card Protection Settings
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•A150 Modify a 1:1 Protection Group
•A152 Modify a 1:N Protection Group
•A154 Modify a 1+1 Protection Group
•A35 Modify an Optimized 1+1 Protection Group
•A155 Delete a Protection Group
Step 4 Complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-A292 Modify or Delete Communications Channel Terminations and Provisionable Patchcords
Purpose |
This procedure changes or deletes SDCC and LDCC terminations and deletes provisionable patchcords on the ONS 15454. |
Tools/Equipment |
None |
Prerequisite Procedures |
A377 Provision Section DCC Terminations or A378 Provision Line DCC Terminations or |
Required/As Needed |
As needed |
Onsite/Remote |
Onsite or remote |
Security Level |
Provisioning or higher |
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 As needed, complete the following tasks to modify DCC settings:
•A374 Change a Section DCC Termination.
•A375 Change a Line DCC Termination.
Step 3 As needed, complete the following tasks to delete DCC terminations:
•A156 Delete a Section DCC Termination.
•A359 Delete a Line DCC Termination.
Step 4 As needed, complete the "DLP-A368 Delete a Provisionable Patchcord" task.
Stop. You have completed this procedure.
NTP-A85 Change Node Timing
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 As needed, complete the "DLP-A157 Change the Node Timing Source" task.
Step 4 If you need to change any internal timing settings, follow the "DLP-A70 Set Up Internal Timing" task for the settings you need to modify.
Step 5 If you need to verify timing after removing a node from a bidirectional line switched ring (BLSR) or path protection, see the "DLP-A195 Verify Timing in a Reduced Ring" task.
Step 6 Complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-A205 Modify Users and Change Security
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•A462 View and Terminate Active Logins
•A271 Change Security Policy on a Single Node
•A272 Change Security Policy on Multiple Nodes
•A512 Change Node Access and PM Clearing Privilege
•A457 Grant Superuser Privileges to a Provisioning User
•A158 Change User Password and Security Level on a Single Node
•A160 Change User Password and Security Level on Multiple Nodes
•A159 Delete a User from a Single Node
•A161 Delete a User from Multiple Nodes
•A456 Configure the Node for RADIUS Authentication; this task includes instructions for modifying or deleting a RADIUS server.
Step 4 Complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.
NTP-A87 Change SNMP Settings
Step 1 Complete the "DLP-A60 Log into CTC" task. If you are already logged in, continue with Step 2.
Step 2 Complete the "NTP-A108 Back Up the Database" procedure.
Step 3 Perform any of the following tasks as needed:
•A273 Modify SNMP Trap Destinations
•A163 Delete SNMP Trap Destinations
Step 4 Complete the "NTP-A108 Back Up the Database" procedure.
Stop. You have completed this procedure.