QoS: Classification Configuration Guide, Cisco IOS XE Gibraltar 16.12.x

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Restrictions for QoS dVTI

With hierarchical egress policy-maps, the topmost policy may only have class-default
Priority, bandwidth, fair-queue may only be configured at the lowest level of a policy-map hierarchy containing queuing features
Only 2000 dVTI tunnels can have QoS configured
Output QoS may not be configured on both the dVTI tunnel template and the output physical

Information About QoS for dVTI

A single dVTI template can support numerous connections from routers with static VTI (sVTI) configuration. The dVTI template configuration is typically on a hub router. Remote spoke routers have a sVTI configuration that always points to the hub router. QoS for dVTI supports the following:

Maximum of 4000 dynamic tunnels using QoS from the dVTI tunnel template
Scalability for an additional 2000 dynamic tunnels with no QoS on the dVTI tunnel template
Low latency egress queuing on dVTI tunnel templates
Egress shaping (with and without overhead accounting) on dVTI tunnel templates

Configuration Examples for QoS for dVTI

Example 2 Layer Rate LLQ for dVTI

This example shows how to configure a 2 Layer egress policy-map on the virtual tunnel interface which gives the following:

ToS-specific rate LLQ for certain traffic
Overall rate limiting on a per-tunnel basis
Additional overhead is considered using the account directive on the shape command in the parent shaper

class-map match-any real_time
  match ip dscp cs5  ef
!
class-map match-any generic_data
  match ip dscp cs1 cs2 af21 af22
  match ip dscp default 
!
policy-map child
class real_time
  police cir 200000
   conform-action transmit
   exceed-action drop
   violate-action drop
  priority
class generic_data
  bandwidth remaining percent 100
!
policy-map parent
  class class-default
  shape average 1000000 account user-defined 30
  service-policy child
!
interface Virtual-Template 1 type tunnel
  service-policy output parent

Example 2 Layer Rate LLQ with Bandwidth Guarantees for dVTI

This example shows how to configure a 2 Layer egress policy-map on the virtual tunnel interface which gives the following:

ToS-specific rate LLQ for certain traffic
Bandwidth guarantees for other traffic
Overall rate limiting on a per-tunnel basis

class-map match-any real_time
match ip precedence 5
!
class-map match-any higher_data_1
match ip precedence 2
!
class-map match-any higher_data_2
match ip precedence 3
!
policy-map child
  class real_time priority
    police 5000000 conform-action transmit exceed-action drop violate-action drop
  class higher_data_1
    bandwidth remaining percent 50
  class higher_data_2
    bandwidth remaining percent 40
  class class-default
    shape average 10000000
  bandwidth remaining percent 5
!
policy-map parent
  class class-default shape average 15000000
  service-policy child
!
interface Virtual-Template 1 type tunnel
service-policy output parent

Example 3 Layer QoS for dVTI

policy-map parent
  Class class-default
      Shape average 50000000
      Bandwidth remaining ratio 1
      Service-policy child
!
policy-map child
    Class Red
      Shape average percent 80
      Bandwidth remaining ratio 9
      Service-policy grandchild
    Class Green
      Shape average percent 80
      Bandwidth remaining ratio 2
      Service-policy grandchild
!
policy-map grandchild
  Class voice
    Priority level 1
  Class video
    Priority level 2
  Class data_gold
    Bandwidth remaining ratio 100
  Class class-default
    Random-detect dscp-based
!
 
interface virtual-template101 type tunnel
ip unnumbered looback101
tunnel source GigabitEthernet0/3/0
service-policy output parent

Additional References

Standards and RFCs


Standard/RFC	Title

MIBs


MIB	MIBs Link
	To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL: http://www.cisco.com/go/mibs

Technical Assistance


Description	Link
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.	http://www.cisco.com/cisco/web/support/index.html

Feature Information for QoS for dVTI

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Table 1. Feature Information for QoS for dVTI
Feature Name	Releases	Feature Information
QoS for dVTI	Cisco IOS XE Release 2.1	QoS for dVTI configures a single dVTI tunnel template.

Related Topic	Document Title
Cisco IOS commands	Cisco IOS Master Commands List, All Releases

Bias-Free Language

Book Title

QoS: Classification Configuration Guide, Cisco IOS XE Gibraltar 16.12.x

Chapter Title

QoS for dVTI

Results

Chapter: QoS for dVTI