Contents

MPLS VPN VRF Selection Using Policy-Based Routing

The MPLS VPN VRF Selection Using Policy-Based Routing feature is an extension of the MPLS VPN VRF Selection Based on Source IP Address feature. This feature introduces a policy-based routing (PBR) mechanism to classify and forward Virtual Private Network (VPN) traffic based on multiple VPN routing and forwarding (VRF) selection match criteria.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for MPLS VPN VRF Selection Using Policy-Based Routing

  • The device must support policy-based routing (PBR). For platforms that do not support PBR, use the “MPLS VPN VRF Selection Based on Source IP Address” feature.

  • A virtual routing and forwarding (VRF) instance must be defined prior to the configuration of this feature. An error message is displayed on the console if no VRF exists.

  • Before you configure the MPLS VPN VRF Selection Using Policy-Based Routing feature, make sure that the VRF and associated IP address are already defined.

  • This document assumes that multiprotocol Border Gateway Protocol (mBGP), Multiprotocol Label Switching (MPLS), and Cisco Express Forwarding are enabled in your network.

Restrictions for MPLS VPN VRF Selection Using Policy-Based Routing

  • The MPLS VPN VRF Selection Using Policy-Based Routing feature is supported only in service provider (-p-) images.

  • The MPLS VPN VRF Selection Using Policy-Based Routing feature can coexist with the MPLS VPN VRF Selection Based on Source IP address feature on the same device, but these features cannot be configured together on the same interface. This is designed behavior to prevent virtual routing and forwarding (VRF) table selection conflicts that could occur if these features were misconfigured together. An error message is displayed on the console if you attempt to configure the ip vrf select source and the ip policy route-map commands on the same interface.

  • Protocol Independent Multicast (PIM) and multicast packets do not support policy-based routing (PBR) and cannot be configured for a source IP address that is a match criterion for this feature.

  • The MPLS VPN VRF Selection Using Policy-Based Routing feature cannot be configured with IP prefix lists.

Information About MPLS VPN VRF Selection Using Policy-Based Routing

Introduction to MPLS VPN VRF Selection Using Policy-Based Routing

The MPLS VPN VRF Selection Using Policy-Based Routing feature is an extension of the MPLS VPN VRF Selection Based on Source IP Address feature. The policy-based routing (PBR) implementation of the virtual routing and forwarding (VRF) selection feature allows you to policy route Virtual Private Network (VPN) traffic based on match criteria. Match criteria are defined in an IP access list or based on packet length. The following match criteria are supported in Cisco software:

  • IP access lists—Define match criteria based on IP addresses, IP address ranges, and other IP packet access list filtering options. Named, numbered, standard, and extended access lists are supported. All IP access-list configuration options in Cisco software can be used to define match criteria.

  • Packet lengths—Define match criteria based on the length of a packet in bytes. The packet length filter is defined in a route map with the match length route-map configuration command.

Policy routing is defined in the route map. The route map is applied to the incoming interface with the ip policy route-map interface configuration command. An IP access list is applied to the route map with the match ip address route-map configuration command. Packet length match criteria are applied to the route map with the match length route-map configuration command. The set action is defined with the set vrf route-map configuration command. The match criteria are evaluated, and the appropriate VRF is selected by the set clause. This combination allows you to define match criteria for incoming VPN traffic and policy route VPN packets out to the appropriate VRF.

Policy-Based Routing Set Clauses Overview

When you are configuring policy-based routing (PBR), the following four set clauses can be used to change normal routing and forwarding behavior:

  • set default interface

  • set interface

  • set ip default next-hop

  • set ip next-hop

Configuring any of the set clauses will overwrite normal routing forwarding behavior of a packet.

The MPLS VPN VRF Selection Using Policy-Based Routing feature introduces the fifth set clause that can be used to change normal routing and forwarding behavior. The set vrf command is used to select the appropriate virtual routing and forwarding (VRF) instance after the successful match occurs in the route map.

Match Criteria for Policy-Based Routing VRF Selection Based on Packet Length

The match criteria for policy-based routing (PBR) virtual routing and forwarding (VRF) route selection are defined in an access list. Standard and named access lists are supported. Match criteria can also be defined based on the packet length using the match length route-map configuration command. This configuration option is defined entirely within a route map.

How to Configure MPLS VPN VRF Selection Using Policy-Based Routing

Configuring Policy-Based Routing VRF Selection with a Standard Access List

Use the following commands to create a standard access list and define the policy-based routing (PBR) virtual routing and forwarding (VRF) route selection match criteria in it in order to permit or deny the transmission of VPN traffic data packets.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    access-list access-list-number {deny | permit} source-addr [source-wildcard] [log]


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 access-list access-list-number {deny | permit} source-addr [source-wildcard] [log]


    Example:
    Device(config)# access-list 40 permit 10.1.0.0/24 0.0.0.255
     

    Creates an access list and defines the match criteria for the route map.

    • Match criteria can be defined based on IP addresses, IP address ranges, and other IP packet access-list filtering options. Named, numbered, standard, and extended access lists are supported. All IP access list configuration options in Cisco software can be used to define match criteria.

    • The example creates a standard access list numbered 40. This filter will permit traffic from any host with an IP address in the 10.1.0.0/24 subnet.

     

    Configuring Policy-Based Routing VRF Selection with a Named Access List

    Use the following commands to define the policy-based routing (PBR) virtual routing and forwarding (VRF) route selection match criteria in a named access list in order to permit or deny the transmission of Virtual Private Network (VPN) traffic data packets.

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    ip access-list {standard | extended} [access-list-name | access-list-number]

      4.    [sequence-number] {permit | deny} protocol source-addr source-wildcard destination-addr destination-wildcard [option option-value] [precedence precedence] [tos tos] [log] [time-range time-range-name] [fragments]


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 ip access-list {standard | extended} [access-list-name | access-list-number]


      Example:
      Device(config)# ip access-list extended NAMEDACL
       

      Specifies the IP access list type and enters the corresponding access-list configuration mode.

      • A standard, extended, or named access list can be used.

       
      Step 4 [sequence-number] {permit | deny} protocol source-addr source-wildcard destination-addr destination-wildcard [option option-value] [precedence precedence] [tos tos] [log] [time-range time-range-name] [fragments]


      Example:
      Device(config-ext-nacl)# permit ip any any option any-options
       

      Defines the criteria for which the access list will permit or deny packets.

      • Match criteria can be defined based on IP addresses, IP address ranges, and other IP packet access-list filtering options. Named, numbered, standard, and extended access lists are supported. All IP access-list configuration options in Cisco software can be used to define match criteria.

      • The example creates a named access list that permits any configured IP option.

       

      Configuring Policy-Based Routing VRF Selection in a Route Map

      Use the following commands to configure the VRF through which the outbound Virtual Private Network (VPN) packets will be policy routed in order to permit or deny the transmission of VPN traffic data packets.

      Incoming packets are filtered through the match criteria that are defined in the route map. After a successful match occurs, the set vrf command configuration determines the VRF through which the outbound VPN packets will be policy routed.

      Before You Begin

      • The virtual routing and forwarding (VRF) instance must be defined prior to the configuration of the route map; otherwise, an error message is displayed on the console.

      • A receive entry must be added to the VRF selection table with the ip vrf receive command. If a match and set operation occurs in the route map but there is no receive entry in the local VRF table, the packet will be dropped if the packet destination is local.

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    route-map map-tag [permit | deny] [sequence-number]

        4.    Do one of the following:

        • match ip address {acl-number [acl-number ... | acl-name ...] | acl-name [acl-name ... | acl-number ...]}
        • match length minimum-length maximum-length

        5.    set vrf vrf-name

        6.    exit


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example:
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3 route-map map-tag [permit | deny] [sequence-number]


        Example:
        Device(config)# route-map map1 permit 10
         

        Enters route map configuration mode.

        Defines the conditions for redistributing routes from one routing protocol into another, or enables policy routing.

         
        Step 4Do one of the following:
        • match ip address {acl-number [acl-number ... | acl-name ...] | acl-name [acl-name ... | acl-number ...]}
        • match length minimum-length maximum-length


        Example:
        Device(config-route-map)# match ip address 1


        Example:
        Device(config-route-map)# match length 3 200
         

        Distributes any routes that have a destination network number address that is permitted by a standard or extended access list, and performs policy routing on matched packets.

        • IP access lists are supported.

        • The example configures the route map to use standard access list 1 to define match criteria.

        or

        Specifies the Layer 3 packet length in the IP header as a match criterion in a class map.

        • The example configures the route map to match packets that are 3 to 200 bytes in size.

         
        Step 5 set vrf vrf-name


        Example:
        Device(config-route-map)# set vrf map1
         

        Defines which VRF to route VPN packets that are successfully matched in the same route map sequence for policy-based routing (PBR) VRF selection.

        • The example policy routes matched packets out to the VRF named map1.

         
        Step 6 exit


        Example:
        Device(config-route-map)# exit
         

        Returns to global configuration mode.

         

        Configuring Policy-Based Routing on the Interface

        Use the following commands to filter incoming Virtual Private Network (VPN) traffic data packets. Incoming packets are filtered through the match criteria that are defined in the route map.

        The route map is applied to the incoming interface. The route map is attached to the incoming interface with the ip policy route-map global configuration command.


        Note
        • The MPLS VPN VRF Selection Using Policy-Based Routing feature can coexist with the MPLS VPN VRF Selection Based on Source IP address feature on the same device, but the two features cannot be configured together on the same interface. This is designed behavior to prevent virtual routing and forwarding (VRF) table selection conflicts that could occur if these features were misconfigured together. An error message is displayed on the console if you attempt to configure the ip vrf select source and the ip policy route-map commands on the same interface.
        >
        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    interface type number [name-tag]

          4.    ip policy route-map map-tag

          5.    ip vrf receive vrf-name

          6.    exit


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Device> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.

           
          Step 2 configure terminal


          Example:
          Device# configure terminal
           

          Enters global configuration mode.

           
          Step 3 interface type number [name-tag]


          Example:
          Device(config)# interface FastEthernet 0/1/0
           

          Configures an interface and enters interface configuration mode.

           
          Step 4 ip policy route-map map-tag


          Example:
          Device(config-if)# ip policy route-map map1
           

          Identifies a route map to use for policy routing on an interface.

          • The configuration example attaches the route map named map1 to the interface.

           
          Step 5 ip vrf receive vrf-name


          Example:
          Device(config-if)# ip vrf receive VRF1
           

          Adds the IP addresses that are associated with an interface into the VRF table.

          • This command must be configured for each VRF that will be used for VRF selection.

           
          Step 6 exit


          Example:
          Device(config-if)# exit
           

          Exits interface configuration mode and enters global configuration mode.

           

          Configuring IP VRF Receive on the Interface

          Use the following commands to insert the IP address of an interface as a connected route entry in a virtual routing and forwarding (VRF) routing table. This will prevent dropped packets.

          The source IP address must be added to the VRF selection table. VRF selection is a one-way (unidirectional) feature. It is applied to the incoming interface. If a match and set operation occurs in the route map but there is no VRF receive entry in the local VRF table, the packet will be dropped if the packet destination is local.

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    interface type number [name-tag]

            4.    ip policy route-map map-tag

            5.    ip vrf receive vrf-name

            6.    end


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Device> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Device# configure terminal
             

            Enters global configuration mode.

             
            Step 3 interface type number [name-tag]


            Example:
            Device(config)# interface FastEthernet 0/1/0
             

            Configures an interface and enters interface configuration mode.

             
            Step 4 ip policy route-map map-tag


            Example:
            Device(config-if)# ip policy route-map map1
             

            Identifies a route map to use for policy routing on an interface.

            • The configuration example attaches the route map named map1 to the interface.

             
            Step 5 ip vrf receive vrf-name


            Example:
            Device(config-if)# ip vrf receive VRF1
             

            Adds the IP addresses that are associated with an interface into the VRF table.

            • This command must be configured for each VRF that will be used for VRF selection.

             
            Step 6 end


            Example:
            Device(config-if)# end
             

            Returns to privileged EXEC mode.

             

            Verifying the Configuration of the MPLS VPN VRF Selection Using Policy-Based Routing

            SUMMARY STEPS

              1.    enable

              2.    show ip access-list [access-list-number | access-list-name]

              3.    show route-map [map-name]

              4.    show ip policy


            DETAILED STEPS
               Command or ActionPurpose
              Step 1 enable


              Example:
              Device> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 show ip access-list [access-list-number | access-list-name]


              Example:
              Device# show ip access-list
               

              Displays the contents of all current IP access lists.

              • This command is used to verify the match criteria that are defined in the access list. Both named and numbered access lists are supported.

               
              Step 3 show route-map [map-name]


              Example:
              Device# show route-map
               

              Displays all route maps configured or only the one specified.

              • This command is used to verify match and set clauses within the route map.

               
              Step 4 show ip policy


              Example:
              Device# show ip policy
               

              Displays the route map used for policy routing.

              • This command can be used to display the route map and the associated interface.

               

              Configuration Examples for MPLS VPN VRF Selection Using Policy-Based Routing

              Example: Defining Policy-Based Routing VRF Selection in an Access List

              In the following example, three standard access lists are created to define match criteria for three different subnets. Any packets received on the FastEthernet 0/1/0 interface will be policy routed through the policy-based routing (PBR) VRF selection route map to the virtual routing and forwarding (VRF) instancer that is matched in the same route map sequence. If the source IP address of the packet is part of the 10.1.0.0/24 subnet, VRF1 will be used for routing and forwarding. 

              access-list 40 permit 10.1.0.0 0.0.255.255
access-list 50 permit 10.2.0.0 0.0.255.255
access-list 60 permit 10.3.0.0 0.0.255.255
route-map PBR-VRF-Selection permit 10
 match ip address 40
 set vrf VRF1
 !
route-map PBR-VRF-Selection permit 20
 match ip address 50
 set vrf VRF2
 !
route-map PBR-VRF-Selection permit 30
 match ip address 60
 set vrf VRF3
 !
interface FastEthernet0/1/0
 ip address 10.1.0.0/24 255.255.255.252
 ip policy route-map PBR-VRF-Selection
 ip vrf receive VRF1
 ip vrf receive VRF2
 ip vrf receive VRF3

              Examples: Verifying VRF Selection Using Policy-Based Routing

              The following verification examples show defined match criteria and route-map policy configuration.

              Example: Verifying Match Criteria

              To verify the configuration of match criteria for policy-based routing (PBR) VRF selection, use the show ip access-list command.

              The following show ip access-list command output displays three subnet ranges defined as match criteria in three standard access lists: 

              Device# show ip access-list

Standard IP access list 40
    10 permit 10.1.0.0, wildcard bits 0.0.255.255
Standard IP access list 50
    10 permit 10.2.0.0, wildcard bits 0.0.255.255
Standard IP access list 60
    10 permit 10.3.0.0, wildcard bits 0.0.255.255

              Example: Verifying Route-Map Configuration

              To verify route-map configuration, use the show route-map command. The output displays the match criteria and set action for each route-map sequence. The output also displays the number of packets and bytes that have been policy routed per each route-map sequence. 

              Device# show route-map

route-map PBR-VRF-Selection, permit, sequence 10
  Match clauses:
    ip address (access-lists): 40 
  Set clauses:
    vrf VRF1
  Policy routing matches: 0 packets, 0 bytes
route-map PBR-VRF-Selection, permit, sequence 20
  Match clauses:
    ip address (access-lists): 50 
  Set clauses:
    vrf VRF2
  Policy routing matches: 0 packets, 0 bytes
route-map PBR-VRF-Selection, permit, sequence 30
  Match clauses:
    ip address (access-lists): 60 
  Set clauses:
    vrf VRF3
  Policy routing matches: 0 packets, 0 bytes

              Example: Verifying Policy-Based Routing VRF Selection Policy

              The following show ip policy command output displays the interface and associated route map that is configured for policy routing: 

              Device# show ip policy

Interface                Route map
FastEthernet0/1/0        PBR-VRF-Selection

              Additional References

              Related Documents

              Related Topic

              Document Title

              Cisco IOS commands

              Cisco Master Command List, All Releases

              MPLS and MPLS applications commands

              Cisco IOS Multiprotocol Label Switching Command Reference

              Technical Assistance

              Description

              Link

              The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

              http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

              Feature Information for MPLS VPN VRF Selection Using Policy-Based Routing

              The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

              Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

              Table 1 Feature Information for MPLS VPN VRF Selection Using Policy-Based Routing

              Feature Name

              Releases

              Feature Information

              MPLS VPN VRF Selection Using Policy-Based Routing

              12.3(7)T

              12.2(25)S

              12.2(33)SRB

              12.2(33)SXI

              Cisco IOS XE Release 2.2

              The MPLS VPN VRF Selection Using Policy-Based Routing feature is an extension of the MPLS VPN VRF Selection Based on Source IP Address feature. This feature introduces a policy-based routing (PBR) mechanism to classify and forward Virtual Private Network (VPN) traffic based on multiple VPN routing and forwarding (VRF) selection match criteria.

              In Cisco IOS Release 12.3(7)T, this feature was introduced.

              In Cisco IOS Releases 12.2(25)S, 12.2(33)SRB, and 12.2(33)SXI, this feature was integrated.

              In Cisco IOS XE Release 2.2, this feature was implemented on Cisco ASR 1000 Series Aggregation Services Routers.

              The following commands were introduced or modified: ip vrf receive, set vrf.

              MPLS VPN VRF Selection Using Policy-Based Routing

              Contents

              MPLS VPN VRF Selection Using Policy-Based Routing

              The MPLS VPN VRF Selection Using Policy-Based Routing feature is an extension of the MPLS VPN VRF Selection Based on Source IP Address feature. This feature introduces a policy-based routing (PBR) mechanism to classify and forward Virtual Private Network (VPN) traffic based on multiple VPN routing and forwarding (VRF) selection match criteria.

              Finding Feature Information

              Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

              Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

              Prerequisites for MPLS VPN VRF Selection Using Policy-Based Routing

              • The device must support policy-based routing (PBR). For platforms that do not support PBR, use the “MPLS VPN VRF Selection Based on Source IP Address” feature.

              • A virtual routing and forwarding (VRF) instance must be defined prior to the configuration of this feature. An error message is displayed on the console if no VRF exists.

              • Before you configure the MPLS VPN VRF Selection Using Policy-Based Routing feature, make sure that the VRF and associated IP address are already defined.

              • This document assumes that multiprotocol Border Gateway Protocol (mBGP), Multiprotocol Label Switching (MPLS), and Cisco Express Forwarding are enabled in your network.

              Restrictions for MPLS VPN VRF Selection Using Policy-Based Routing

              • The MPLS VPN VRF Selection Using Policy-Based Routing feature is supported only in service provider (-p-) images.

              • The MPLS VPN VRF Selection Using Policy-Based Routing feature can coexist with the MPLS VPN VRF Selection Based on Source IP address feature on the same device, but these features cannot be configured together on the same interface. This is designed behavior to prevent virtual routing and forwarding (VRF) table selection conflicts that could occur if these features were misconfigured together. An error message is displayed on the console if you attempt to configure the ip vrf select source and the ip policy route-map commands on the same interface.

              • Protocol Independent Multicast (PIM) and multicast packets do not support policy-based routing (PBR) and cannot be configured for a source IP address that is a match criterion for this feature.

              • The MPLS VPN VRF Selection Using Policy-Based Routing feature cannot be configured with IP prefix lists.

              Information About MPLS VPN VRF Selection Using Policy-Based Routing

              Introduction to MPLS VPN VRF Selection Using Policy-Based Routing

              The MPLS VPN VRF Selection Using Policy-Based Routing feature is an extension of the MPLS VPN VRF Selection Based on Source IP Address feature. The policy-based routing (PBR) implementation of the virtual routing and forwarding (VRF) selection feature allows you to policy route Virtual Private Network (VPN) traffic based on match criteria. Match criteria are defined in an IP access list or based on packet length. The following match criteria are supported in Cisco software:

              • IP access lists—Define match criteria based on IP addresses, IP address ranges, and other IP packet access list filtering options. Named, numbered, standard, and extended access lists are supported. All IP access-list configuration options in Cisco software can be used to define match criteria.

              • Packet lengths—Define match criteria based on the length of a packet in bytes. The packet length filter is defined in a route map with the match length route-map configuration command.

              Policy routing is defined in the route map. The route map is applied to the incoming interface with the ip policy route-map interface configuration command. An IP access list is applied to the route map with the match ip address route-map configuration command. Packet length match criteria are applied to the route map with the match length route-map configuration command. The set action is defined with the set vrf route-map configuration command. The match criteria are evaluated, and the appropriate VRF is selected by the set clause. This combination allows you to define match criteria for incoming VPN traffic and policy route VPN packets out to the appropriate VRF.

              Policy-Based Routing Set Clauses Overview

              When you are configuring policy-based routing (PBR), the following four set clauses can be used to change normal routing and forwarding behavior:

              • set default interface

              • set interface

              • set ip default next-hop

              • set ip next-hop

              Configuring any of the set clauses will overwrite normal routing forwarding behavior of a packet.

              The MPLS VPN VRF Selection Using Policy-Based Routing feature introduces the fifth set clause that can be used to change normal routing and forwarding behavior. The set vrf command is used to select the appropriate virtual routing and forwarding (VRF) instance after the successful match occurs in the route map.

              Match Criteria for Policy-Based Routing VRF Selection Based on Packet Length

              The match criteria for policy-based routing (PBR) virtual routing and forwarding (VRF) route selection are defined in an access list. Standard and named access lists are supported. Match criteria can also be defined based on the packet length using the match length route-map configuration command. This configuration option is defined entirely within a route map.

              How to Configure MPLS VPN VRF Selection Using Policy-Based Routing

              Configuring Policy-Based Routing VRF Selection with a Standard Access List

              Use the following commands to create a standard access list and define the policy-based routing (PBR) virtual routing and forwarding (VRF) route selection match criteria in it in order to permit or deny the transmission of VPN traffic data packets.

              SUMMARY STEPS

                1.    enable

                2.    configure terminal

                3.    access-list access-list-number {deny | permit} source-addr [source-wildcard] [log]


              DETAILED STEPS
                 Command or ActionPurpose
                Step 1 enable


                Example:
                Device> enable
                 

                Enables privileged EXEC mode.

                • Enter your password if prompted.

                 
                Step 2 configure terminal


                Example:
                Device# configure terminal
                 

                Enters global configuration mode.

                 
                Step 3 access-list access-list-number {deny | permit} source-addr [source-wildcard] [log]


                Example:
                Device(config)# access-list 40 permit 10.1.0.0/24 0.0.0.255
                 

                Creates an access list and defines the match criteria for the route map.

                • Match criteria can be defined based on IP addresses, IP address ranges, and other IP packet access-list filtering options. Named, numbered, standard, and extended access lists are supported. All IP access list configuration options in Cisco software can be used to define match criteria.

                • The example creates a standard access list numbered 40. This filter will permit traffic from any host with an IP address in the 10.1.0.0/24 subnet.

                 

                Configuring Policy-Based Routing VRF Selection with a Named Access List

                Use the following commands to define the policy-based routing (PBR) virtual routing and forwarding (VRF) route selection match criteria in a named access list in order to permit or deny the transmission of Virtual Private Network (VPN) traffic data packets.

                SUMMARY STEPS

                  1.    enable

                  2.    configure terminal

                  3.    ip access-list {standard | extended} [access-list-name | access-list-number]

                  4.    [sequence-number] {permit | deny} protocol source-addr source-wildcard destination-addr destination-wildcard [option option-value] [precedence precedence] [tos tos] [log] [time-range time-range-name] [fragments]


                DETAILED STEPS
                   Command or ActionPurpose
                  Step 1 enable


                  Example:
                  Device> enable
                   

                  Enables privileged EXEC mode.

                  • Enter your password if prompted.

                   
                  Step 2 configure terminal


                  Example:
                  Device# configure terminal
                   

                  Enters global configuration mode.

                   
                  Step 3 ip access-list {standard | extended} [access-list-name | access-list-number]


                  Example:
                  Device(config)# ip access-list extended NAMEDACL
                   

                  Specifies the IP access list type and enters the corresponding access-list configuration mode.

                  • A standard, extended, or named access list can be used.

                   
                  Step 4 [sequence-number] {permit | deny} protocol source-addr source-wildcard destination-addr destination-wildcard [option option-value] [precedence precedence] [tos tos] [log] [time-range time-range-name] [fragments]


                  Example:
                  Device(config-ext-nacl)# permit ip any any option any-options
                   

                  Defines the criteria for which the access list will permit or deny packets.

                  • Match criteria can be defined based on IP addresses, IP address ranges, and other IP packet access-list filtering options. Named, numbered, standard, and extended access lists are supported. All IP access-list configuration options in Cisco software can be used to define match criteria.

                  • The example creates a named access list that permits any configured IP option.

                   

                  Configuring Policy-Based Routing VRF Selection in a Route Map

                  Use the following commands to configure the VRF through which the outbound Virtual Private Network (VPN) packets will be policy routed in order to permit or deny the transmission of VPN traffic data packets.

                  Incoming packets are filtered through the match criteria that are defined in the route map. After a successful match occurs, the set vrf command configuration determines the VRF through which the outbound VPN packets will be policy routed.

                  Before You Begin

                  • The virtual routing and forwarding (VRF) instance must be defined prior to the configuration of the route map; otherwise, an error message is displayed on the console.

                  • A receive entry must be added to the VRF selection table with the ip vrf receive command. If a match and set operation occurs in the route map but there is no receive entry in the local VRF table, the packet will be dropped if the packet destination is local.

                  SUMMARY STEPS

                    1.    enable

                    2.    configure terminal

                    3.    route-map map-tag [permit | deny] [sequence-number]

                    4.    Do one of the following:

                    • match ip address {acl-number [acl-number ... | acl-name ...] | acl-name [acl-name ... | acl-number ...]}
                    • match length minimum-length maximum-length

                    5.    set vrf vrf-name

                    6.    exit


                  DETAILED STEPS
                     Command or ActionPurpose
                    Step 1 enable


                    Example:
                    Device> enable
                     

                    Enables privileged EXEC mode.

                    • Enter your password if prompted.

                     
                    Step 2 configure terminal


                    Example:
                    Device# configure terminal
                     

                    Enters global configuration mode.

                     
                    Step 3 route-map map-tag [permit | deny] [sequence-number]


                    Example:
                    Device(config)# route-map map1 permit 10
                     

                    Enters route map configuration mode.

                    Defines the conditions for redistributing routes from one routing protocol into another, or enables policy routing.

                     
                    Step 4Do one of the following:
                    • match ip address {acl-number [acl-number ... | acl-name ...] | acl-name [acl-name ... | acl-number ...]}
                    • match length minimum-length maximum-length


                    Example:
                    Device(config-route-map)# match ip address 1


                    Example:
                    Device(config-route-map)# match length 3 200
                     

                    Distributes any routes that have a destination network number address that is permitted by a standard or extended access list, and performs policy routing on matched packets.

                    • IP access lists are supported.

                    • The example configures the route map to use standard access list 1 to define match criteria.

                    or

                    Specifies the Layer 3 packet length in the IP header as a match criterion in a class map.

                    • The example configures the route map to match packets that are 3 to 200 bytes in size.

                     
                    Step 5 set vrf vrf-name


                    Example:
                    Device(config-route-map)# set vrf map1
                     

                    Defines which VRF to route VPN packets that are successfully matched in the same route map sequence for policy-based routing (PBR) VRF selection.

                    • The example policy routes matched packets out to the VRF named map1.

                     
                    Step 6 exit


                    Example:
                    Device(config-route-map)# exit
                     

                    Returns to global configuration mode.

                     

                    Configuring Policy-Based Routing on the Interface

                    Use the following commands to filter incoming Virtual Private Network (VPN) traffic data packets. Incoming packets are filtered through the match criteria that are defined in the route map.

                    The route map is applied to the incoming interface. The route map is attached to the incoming interface with the ip policy route-map global configuration command.


                    Note
                    • The MPLS VPN VRF Selection Using Policy-Based Routing feature can coexist with the MPLS VPN VRF Selection Based on Source IP address feature on the same device, but the two features cannot be configured together on the same interface. This is designed behavior to prevent virtual routing and forwarding (VRF) table selection conflicts that could occur if these features were misconfigured together. An error message is displayed on the console if you attempt to configure the ip vrf select source and the ip policy route-map commands on the same interface.
                    >
                    SUMMARY STEPS

                      1.    enable

                      2.    configure terminal

                      3.    interface type number [name-tag]

                      4.    ip policy route-map map-tag

                      5.    ip vrf receive vrf-name

                      6.    exit


                    DETAILED STEPS
                       Command or ActionPurpose
                      Step 1 enable


                      Example:
                      Device> enable
                       

                      Enables privileged EXEC mode.

                      • Enter your password if prompted.

                       
                      Step 2 configure terminal


                      Example:
                      Device# configure terminal
                       

                      Enters global configuration mode.

                       
                      Step 3 interface type number [name-tag]


                      Example:
                      Device(config)# interface FastEthernet 0/1/0
                       

                      Configures an interface and enters interface configuration mode.

                       
                      Step 4 ip policy route-map map-tag


                      Example:
                      Device(config-if)# ip policy route-map map1
                       

                      Identifies a route map to use for policy routing on an interface.

                      • The configuration example attaches the route map named map1 to the interface.

                       
                      Step 5 ip vrf receive vrf-name


                      Example:
                      Device(config-if)# ip vrf receive VRF1
                       

                      Adds the IP addresses that are associated with an interface into the VRF table.

                      • This command must be configured for each VRF that will be used for VRF selection.

                       
                      Step 6 exit


                      Example:
                      Device(config-if)# exit
                       

                      Exits interface configuration mode and enters global configuration mode.

                       

                      Configuring IP VRF Receive on the Interface

                      Use the following commands to insert the IP address of an interface as a connected route entry in a virtual routing and forwarding (VRF) routing table. This will prevent dropped packets.

                      The source IP address must be added to the VRF selection table. VRF selection is a one-way (unidirectional) feature. It is applied to the incoming interface. If a match and set operation occurs in the route map but there is no VRF receive entry in the local VRF table, the packet will be dropped if the packet destination is local.

                      SUMMARY STEPS

                        1.    enable

                        2.    configure terminal

                        3.    interface type number [name-tag]

                        4.    ip policy route-map map-tag

                        5.    ip vrf receive vrf-name

                        6.    end


                      DETAILED STEPS
                         Command or ActionPurpose
                        Step 1 enable


                        Example:
                        Device> enable
                         

                        Enables privileged EXEC mode.

                        • Enter your password if prompted.

                         
                        Step 2 configure terminal


                        Example:
                        Device# configure terminal
                         

                        Enters global configuration mode.

                         
                        Step 3 interface type number [name-tag]


                        Example:
                        Device(config)# interface FastEthernet 0/1/0
                         

                        Configures an interface and enters interface configuration mode.

                         
                        Step 4 ip policy route-map map-tag


                        Example:
                        Device(config-if)# ip policy route-map map1
                         

                        Identifies a route map to use for policy routing on an interface.

                        • The configuration example attaches the route map named map1 to the interface.

                         
                        Step 5 ip vrf receive vrf-name


                        Example:
                        Device(config-if)# ip vrf receive VRF1
                         

                        Adds the IP addresses that are associated with an interface into the VRF table.

                        • This command must be configured for each VRF that will be used for VRF selection.

                         
                        Step 6 end


                        Example:
                        Device(config-if)# end
                         

                        Returns to privileged EXEC mode.

                         

                        Verifying the Configuration of the MPLS VPN VRF Selection Using Policy-Based Routing

                        SUMMARY STEPS

                          1.    enable

                          2.    show ip access-list [access-list-number | access-list-name]

                          3.    show route-map [map-name]

                          4.    show ip policy


                        DETAILED STEPS
                           Command or ActionPurpose
                          Step 1 enable


                          Example:
                          Device> enable
                           

                          Enables privileged EXEC mode.

                          • Enter your password if prompted.

                           
                          Step 2 show ip access-list [access-list-number | access-list-name]


                          Example:
                          Device# show ip access-list
                           

                          Displays the contents of all current IP access lists.

                          • This command is used to verify the match criteria that are defined in the access list. Both named and numbered access lists are supported.

                           
                          Step 3 show route-map [map-name]


                          Example:
                          Device# show route-map
                           

                          Displays all route maps configured or only the one specified.

                          • This command is used to verify match and set clauses within the route map.

                           
                          Step 4 show ip policy


                          Example:
                          Device# show ip policy
                           

                          Displays the route map used for policy routing.

                          • This command can be used to display the route map and the associated interface.

                           

                          Configuration Examples for MPLS VPN VRF Selection Using Policy-Based Routing

                          Example: Defining Policy-Based Routing VRF Selection in an Access List

                          In the following example, three standard access lists are created to define match criteria for three different subnets. Any packets received on the FastEthernet 0/1/0 interface will be policy routed through the policy-based routing (PBR) VRF selection route map to the virtual routing and forwarding (VRF) instancer that is matched in the same route map sequence. If the source IP address of the packet is part of the 10.1.0.0/24 subnet, VRF1 will be used for routing and forwarding. 

                          access-list 40 permit 10.1.0.0 0.0.255.255
access-list 50 permit 10.2.0.0 0.0.255.255
access-list 60 permit 10.3.0.0 0.0.255.255
route-map PBR-VRF-Selection permit 10
 match ip address 40
 set vrf VRF1
 !
route-map PBR-VRF-Selection permit 20
 match ip address 50
 set vrf VRF2
 !
route-map PBR-VRF-Selection permit 30
 match ip address 60
 set vrf VRF3
 !
interface FastEthernet0/1/0
 ip address 10.1.0.0/24 255.255.255.252
 ip policy route-map PBR-VRF-Selection
 ip vrf receive VRF1
 ip vrf receive VRF2
 ip vrf receive VRF3

                          Examples: Verifying VRF Selection Using Policy-Based Routing

                          The following verification examples show defined match criteria and route-map policy configuration.

                          Example: Verifying Match Criteria

                          To verify the configuration of match criteria for policy-based routing (PBR) VRF selection, use the show ip access-list command.

                          The following show ip access-list command output displays three subnet ranges defined as match criteria in three standard access lists: 

                          Device# show ip access-list

Standard IP access list 40
    10 permit 10.1.0.0, wildcard bits 0.0.255.255
Standard IP access list 50
    10 permit 10.2.0.0, wildcard bits 0.0.255.255
Standard IP access list 60
    10 permit 10.3.0.0, wildcard bits 0.0.255.255

                          Example: Verifying Route-Map Configuration

                          To verify route-map configuration, use the show route-map command. The output displays the match criteria and set action for each route-map sequence. The output also displays the number of packets and bytes that have been policy routed per each route-map sequence. 

                          Device# show route-map

route-map PBR-VRF-Selection, permit, sequence 10
  Match clauses:
    ip address (access-lists): 40 
  Set clauses:
    vrf VRF1
  Policy routing matches: 0 packets, 0 bytes
route-map PBR-VRF-Selection, permit, sequence 20
  Match clauses:
    ip address (access-lists): 50 
  Set clauses:
    vrf VRF2
  Policy routing matches: 0 packets, 0 bytes
route-map PBR-VRF-Selection, permit, sequence 30
  Match clauses:
    ip address (access-lists): 60 
  Set clauses:
    vrf VRF3
  Policy routing matches: 0 packets, 0 bytes

                          Example: Verifying Policy-Based Routing VRF Selection Policy

                          The following show ip policy command output displays the interface and associated route map that is configured for policy routing: 

                          Device# show ip policy

Interface                Route map
FastEthernet0/1/0        PBR-VRF-Selection

                          Additional References

                          Related Documents

                          Related Topic

                          Document Title

                          Cisco IOS commands

                          Cisco Master Command List, All Releases

                          MPLS and MPLS applications commands

                          Cisco IOS Multiprotocol Label Switching Command Reference

                          Technical Assistance

                          Description

                          Link

                          The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

                          http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

                          Feature Information for MPLS VPN VRF Selection Using Policy-Based Routing

                          The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

                          Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

                          Table 1 Feature Information for MPLS VPN VRF Selection Using Policy-Based Routing

                          Feature Name

                          Releases

                          Feature Information

                          MPLS VPN VRF Selection Using Policy-Based Routing

                          12.3(7)T

                          12.2(25)S

                          12.2(33)SRB

                          12.2(33)SXI

                          Cisco IOS XE Release 2.2

                          The MPLS VPN VRF Selection Using Policy-Based Routing feature is an extension of the MPLS VPN VRF Selection Based on Source IP Address feature. This feature introduces a policy-based routing (PBR) mechanism to classify and forward Virtual Private Network (VPN) traffic based on multiple VPN routing and forwarding (VRF) selection match criteria.

                          In Cisco IOS Release 12.3(7)T, this feature was introduced.

                          In Cisco IOS Releases 12.2(25)S, 12.2(33)SRB, and 12.2(33)SXI, this feature was integrated.

                          In Cisco IOS XE Release 2.2, this feature was implemented on Cisco ASR 1000 Series Aggregation Services Routers.

                          The following commands were introduced or modified: ip vrf receive, set vrf.