EIGRP Over the Top

The EIGRP Over the Top feature enables a single end-to-end routing domain between two or more Enhanced Interior Gateway Routing Protocol (EIGRP) sites that are connected using a private or a public WAN connection. This module provides information about the EIGRP Over the Top feature and how to configure it.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Information About EIGRP Over the Top

EIGRP Over the Top Overview

The EIGRP Over the Top feature enables a single end-to-end Enhanced Interior Gateway Routing Protocol (EIGRP) routing domain that is transparent to the underlying public or private WAN transport that is used for connecting disparate EIGRP customer sites. When an enterprise extends its connectivity across multiple sites through a private or a public WAN connection, the service provider mandates that the enterprise use an additional routing protocol, typically the Border Gateway Protocol (BGP), over the WAN links to ensure end-to-end routing. The use of an additional protocol causes additional complexities for the enterprise, such as additional routing processes and sustained interaction between EIGRP and the routing protocol to ensure connectivity, for the enterprise. With the EIGRP Over the Top feature, routing is consolidated into a single protocol (EIGRP) across the WAN, which provides the following benefits:

  • There is no dependency on the type of WAN connection used.

  • There is no dependency on the service provider to transfer routes.

  • There is no security threat because the underlying WAN has no knowledge of enterprise routes.

  • This feature simplifies dual carrier deployments and designs by eliminating the need to configure and manage EIGRP-BGP route distribution and route filtering between customer sites.

  • This feature allows easy transition between different service providers.

  • This feature supports both IPv4 and IPv6 environments.

How EIGRP Over the Top Works

The EIGRP Over the Top solution can be used to ensure connectivity between disparate Enhanced Interior Gateway Routing Protocol (EIGRP) sites. This feature uses EIGRP on the control plane and Locator ID Separation Protocol (LISP) encapsulation on the data plane to route traffic across the underlying WAN architecture. EIGRP is used to distribute routes between customer edge (CE) devices within the network, and the traffic forwarded across the WAN architecture is LISP encapsulated. Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network.

If your network has many CEs, then you can use EIGRP Route Reflectors (E-RRs) to form a half-mesh topology and ensure connectivity among all CEs in the network. An E-RR is an EIGRP peer that receives EIGRP route updates from CEs in the network and reflects these updates to other EIGRP CE neighbors without changing the next hop or metrics for the routes. An E-RR can also function as a CE in the network. You must configure E-RRs with the remote-neighbors source command to enable E-RRs to listen to unicast messages from peer CE devices and reflect the messages to other EIGRP CE neighbors. You must configure the CEs with the neighbor command to allow them to identify the E-RRs in their network and exchange routes with the E-RRs. Upon learning routes from E-RRs, the CEs install these routes into their routing information base (RIB). You can use dual or multiple E-RRs for redundancy. The CEs form adjacencies with all E-RRs configured in the network, thus enabling multihop remote neighborship amongst themselves.

Security Groups and SGTs

A security group is a grouping of users, endpoint devices, and resources that share access control policies. Security groups are defined by the administrator in the ACS. As new users and devices are added to the Cisco TrustSec (CTS) domain, the authentication server assigns these new entities to appropriate security groups. CTS assigns to each security group a unique 16-bit security group number whose scope is global within a CTS domain. The number of security groups in the router is limited to the number of authenticated network entities. Security group numbers do not need to be manually configured.

Once a device is authenticated, CTS tags any packet that originates from that device with an SGT that contains the security group number of the device. The packet carries this SGT throughout the network within the CTS header. The SGT is a single label that determines the privileges of the source within the entire CTS domain. The SGT is identified as the source because it contains the security group of the source. The destination device is assigned a destination group tag (DGT).

Note

The CTS packet tag does not contain the security group number of the destination device.

EIGRP OTP Support to Propagate SGT

The EIGRP OTP Support enables to propagate SGT from site-to-site across WAN using OTP transport. OTP uses LISP to send the data traffic. OTP carries the SGT over the Layer 3 (L3) clouds across multiple connections/network and also provides access control at a remote site.

How to Configure EIGRP Over the Top

Configuring EIGRP Over the Top on a CE Device

You must enable the EIGRP Over the Top feature on all customer edge (CE) devices in the network so that the CEs know how to reach the Enhanced Interior Gateway Routing Protocol (EIGRP) Route Reflector configured in the network. Perform the following task to configure the EIGRP Over the Top feature on a CE device and enable Locator ID Separation Protocol (LISP) encapsulation for traffic across the underlying WAN.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    router eigrp virtual-name

    4.    address-family ipv4 autonomous-system as-number

    5.    neighbor{ip-address | ipv6-address} interface-type interface-number [remote maximum-hops [lisp-encap [lisp-id]]]

    6.    network ip-address[wildcard-mask]

    7.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 router eigrp virtual-name


    Example:
    Device(config)# router eigrp test
     

    Configures an EIGRP routing process and enters router configuration mode.

     
    Step 4 address-family ipv4 autonomous-system as-number


    Example:
    Device(config-router)# address-family ipv4 autonomous-system 100
     

    Enters address family configuration mode and configures an EIGRP routing instance.

     
    Step 5 neighbor{ip-address | ipv6-address} interface-type interface-number [remote maximum-hops [lisp-encap [lisp-id]]]


    Example:
    Device(config-router-af)# neighbor 10.0.0.1 gigabitethernet 0/0/1 remote 2 lisp-encap 1
     

    Defines a neighboring device with which an EIGRP device can exchange routing information.

     
    Step 6 network ip-address[wildcard-mask]


    Example:
    Device(config-router-af)# network 192.168.0.0 255.255.0.0
     

    Specifies the network for the EIGRP routing process. In this case, configure all routes that the CE needs to be aware of.

     
    Step 7 end


    Example:
    Device(config-router-af)# end
          		Exits address family configuration mode and returns to privileged EXEC mode.  

    Configuring EIGRP Route Reflectors

    Perform this task to configure a customer edge (CE) device in a network to function as an Enhanced Interior Gateway Routing Protocol (EIGRP) Route Reflector.

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    router eigrp virtual-name

      4.    address-family ipv4 unicast autonomous-system as-number

      5.    af-interface interface-type interface-number

      6.    no next-hop-self

      7.    no split-horizon

      8.    exit

      9.    remote-neighbors source interface-type interface-number unicast-listen lisp-encap

      10.    network ip-address

      11.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 router eigrp virtual-name


      Example:
      Device(config)# router eigrp test
       

      Configures an EIGRP routing process and enters router configuration mode.

       
      Step 4 address-family ipv4 unicast autonomous-system as-number


      Example:
      Device(config-router)# address-family ipv4 unicast autonomous-system 100
       

      Enters address family configuration mode and configures an EIGRP routing instance.

       
      Step 5 af-interface interface-type interface-number


      Example:
      Device(config-router-af)# af-interface gigabitethernet 0/0/1
       

      Enters address family interface configuration mode and configures interface-specific EIGRP commands.

       
      Step 6 no next-hop-self


      Example:
      Device(config-router-af-interface)# no next-hop-self
       

      Instructs EIGRP to use the received next hop and not the local outbound interface address as the next hop to be advertised to neighboring devices.

      Note   

      If no next-hop-self is not configured, the data traffic will flow through the EIGRP Route Reflector.

       
      Step 7 no split-horizon


      Example:
      Device(config-router-af-interface)# no split-horizon
       

      Disables EIGRP split horizon.

       
      Step 8 exit


      Example:
      Device(config-router-af-interface)# exit
       

      Exits address family interface configuration mode and returns to address family configuration mode.

       
      Step 9 remote-neighbors source interface-type interface-number unicast-listen lisp-encap


      Example:
      Device(config-router-af)# remote-neighbors source gigabitethernet 0/0/1 unicast-listen lisp-encap
       

      Enables remote neighbors to accept inbound connections from any remote IP address.

       
      Step 10 network ip-address


      Example:
      Device(config-router-af)# network 192.168.0.0
       

      Specifies a network for the EIGRP routing process.

      • Enter all network routes that the EIGRP Route Reflector needs to be aware of.

       
      Step 11 end


      Example:
      Device(config-router-af)# end
       

      Exits address family configuration mode and returns to privileged EXEC mode

       

      Configuring EIGRP OTP Support to Propagate SGT

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    router eigrp virtual instance name

        4.    address-family ipv4 autonomous-system as-number

        5.    topology base

        6.    cts propagate sgt

        7.    end


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example: 
        Device> enable
         
        Enables privileged EXEC mode.
        • Enter your password if prompted.
         
        Step 2configure terminal


        Example: 
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3router eigrp virtual instance name


        Example: 
        Device (config)# router eigrp kmd
         

        Configures an EIGRP routing process and enters router configuration mode.

         
        Step 4address-family ipv4 autonomous-system as-number


        Example: 
        Device (config-router)# address-family ipv4 autonomous-system 100
         

        Enters address family configuration mode and configures an EIGRP routing instance.

         
        Step 5topology base


        Example: 
        Device (config-router-af)# topology base
         

        Configures an EIGRP process to route IP traffic under the specified topology instance and enters address family topology configuration mode.

         
        Step 6cts propagate sgt


        Example: 
        Device (config-router-af)# cts propagate sgt
         

        Enables Security Group Tag (SGT) propagation over L3 network.

         
        Step 7end


        Example: 
        Device (config-router-af)# end
         

        Exits address family topology configuration mode and returns to privileged EXEC mode.

         

        Configuration Examples for EIGRP Over the Top

        Example: Configuring EIGRP Over the Top on a CE Device

        The following example shows you how to configure the customer edge (CE) device in the network to advertise local routes to the Enhanced Interior Gateway Routing Protocol (EIGRP) Route Reflectors.

        Device> enable
Device# configure terminal
Device(config)# router eigrp test
Device(config-router)# address-family ipv4 unicast autonomous-system 100
Device(config-router-af)# neighbor 10.0.0.2 gigabitethernet 0/0/1 remote 3 lisp-encap 1
Device(config-router-af)# network 192.168.0.0
Device(config-router-af)# network 192.168.1.0
Device(config-router-af)# network 192.168.2.0
Device(config-router-af)# end

        Example: Configuring EIGRP Route Reflectors

        Device> enable
Device# configure terminal
Device(config)# router eigrp test
Device(config-router)# address-family ipv4 unicast autonomous-system 100
Device(config-router-af)# af-interface gigabitethernet 0/0/1
Device(config-router-af-interface)# no next-hop-self
Device(config-router-af-interface)# no split-horizon
Device(config-router-af-interface)# exit
Device(config-router-af)# remote-neighbors source gigabitethernet 0/0/1 unicast-listen lisp-encap 1
Device(config-router-af)# network 192.168.0.0
Device(config-router-af)# end

        Example: Configuring EIGRP OTP Support to Propagate SGT

        The following example shows how to configure EIGRP OTP to propagate SGT. 

        router eigrp kmd
!
address-family ipv4 unicast autonomous-system 100
  !
  topology base
   cts propagate sgt
  exit-af-topology
exit-address-family

        Feature Information for EIGRP Over the Top

        The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

        Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
        Table 1 Feature Information for EIGRP Over the Top

        Feature Name

        Releases

        Feature Information

        EIGRP Over the Top

        The EIGRP Over the Top feature enables a single end-to-end routing domain between two or (EIGRP) more Enhanced Interior Gateway Routing Protocol sites that are connected using a private or public WAN connection. EIGRP OTP also supports the propagation of SGT over L3 network.

        The following commands were introduced or modified: remote-neighbor (EIGRP), neighbor (EIGRP), cts propagate sgt ,and show ip eigrp neighbors.