- Title Pages
- Preface
- Chapter 1 - Basic Troubleshooting Tasks and Startup Issues
- Chapter 2 - PEM Faults and Blower Failures
- Chapter 3 - Troubleshooting PRE Modules
- Chapter 4 - Troubleshooting Line Cards
- Chapter 5 - Replacing or Recovering Passwords
- Appendix A - Unsupported Commands
- Index
- Appendix B - Recommended Tools and Test Equipment
Unsupported Commands
The following are lists of the commands that are present but not supported for the Cisco uBR10012 router in various releases of the Cisco IOS software.
•Unsupported Frame Relay Commands
•Unsupported MPLS VPN Commands
•Unsupported Telco-Return Commands
Warning Cisco strongly advises against using unsupported Cisco IOS commands, even if described, because such commands can have undesirable effects upon the performance of the Cisco CMTS. In particular, Cisco advises against using any unsupported commands that pertain to service-policy or to Modular Quality of Service command-line interface (MQC) while Parallel Express Forwarding (PXF) is running on the Cisco CMTS. Such commands may cause the Cisco CMTS to hang with unpredictable recovery times.
Unsupported Frame Relay Commands
The following commands are not supported in any Cisco IOS software release.
•FRF.12 fragmentation commands
•FRF.11 VoFR commands
•frame-relay adaptive-shaping {becn | foresight}
•frame-relay bc {in | out} bits
•frame-relay be {in | out} bits
•frame-relay cir {in | out} bps
•frame-relay custom-queue-list list-number
•frame-relay de-group group-number dlci
•frame-relay ip [rtp | tcp] header-compression [passive]
•frame-relay map protocol protocol-address dlci [broadcast] [ietf | cisco] [payload-compress {packet-by-packet | frf9 stac [hardware-options]}]
•frame-relay map ip ip-address dlci [broadcast] [cisco | ietf] [nocompress] tcp header-compression {active | passive}
•frame-relay mincir {in | out} bps
•frame-relay traffic-rate average [peak]
•frame-relay traffic-shaping
•show frame-relay ip [rtp | tcp] header-compression [interface]
HCCP Commands
The following commands are supported in Cisco IOS Release 12.2(8)BC2 and later 12.2 BC releases. These commands are not supported in previous releases.
•hccp authenticate
•hccp authenticate key-chain
•hccp ds-switch
•hccp lockout
•hccp protect
•hccp revert
•hccp reverttime
•hccp switch
•hccp timers
•hccp track
•hccp unlockout
•hccp working
•show hccp
•show hccp interface
•debug hccp authentication
•debug hccp events
•debug hccp sync
MLPPP Commands
The following commands are supported in Cisco IOS Release 12.2(4)BC1 and later 12.2 BC releases. These commands are not supported in previous releases.
•multilink load-threshold
•multilink max-fragments
•ppp multilink fragment-delay
•ppp multilink fragmentation
•ppp multilink idle-link
•ppp multilink interleave
Unsupported MPLS VPN Commands
The following commands are not supported in any Cisco IOS software release.
•ip vrf
•ip vrf forwarding
•mpls ip
•mpls label-protocol ldp
•show ip protocols vrf
•show ip vrf
•show ip route vrf
Unsupported PPP Commands
The following commands are not supported in any Cisco IOS software release.
•compress [predictor | stac | mppc [ignore-pfc]]
•debug ppp cbcp
•ppp bridge appletalk
•ppp bridge ip
•ppp bridge ipx [novell-ether | arpa | sap | snap]
•ppp reliable-link
Spectrum Management Commands
The following commands are supported in Cisco IOS Release 12.2(8)BC2 and later 12.2 BC releases. These commands are not supported in previous releases.
•cable upstream hop-priority
•cable upstream threshold
•show cable modem [ip-address | interface | mac-address] snr
•show controllers cable upstream spectrum
Unsupported Telco-Return Commands
The following commands are not supported in any Cisco IOS software release.
•cable telco-return enable
•cable telco-return interval
•cable telco-return spd dhcp-authenticate
•cable telco-return spd dhcp-server
•cable telco-return spd dial-timer
•cable telco-return spd factory-default
•cable telco-return spd manual-dial
•cable telco-return spd password
•cable telco-return spd phonenum
•cable telco-return spd ppp-authenticate
•cable telco-return spd radius-realm
•cable telco-return spd service-provider
•cable telco-return spd threshold
•cable telco-return spd username
•debug cable telco-return
•debug telco-return msg