تسعى مجموعة الوثائق لهذا المنتج جاهدة لاستخدام لغة خالية من التحيز. لأغراض مجموعة الوثائق هذه، يتم تعريف "خالية من التحيز" على أنها لغة لا تعني التمييز على أساس العمر، والإعاقة، والجنس، والهوية العرقية، والهوية الإثنية، والتوجه الجنسي، والحالة الاجتماعية والاقتصادية، والتمييز متعدد الجوانب. قد تكون الاستثناءات موجودة في الوثائق بسبب اللغة التي يتم تشفيرها بشكل ثابت في واجهات المستخدم الخاصة ببرنامج المنتج، أو اللغة المستخدمة بناءً على وثائق RFP، أو اللغة التي يستخدمها منتج الجهة الخارجية المُشار إليه. تعرّف على المزيد حول كيفية استخدام Cisco للغة الشاملة.
ترجمت Cisco هذا المستند باستخدام مجموعة من التقنيات الآلية والبشرية لتقديم محتوى دعم للمستخدمين في جميع أنحاء العالم بلغتهم الخاصة. يُرجى ملاحظة أن أفضل ترجمة آلية لن تكون دقيقة كما هو الحال مع الترجمة الاحترافية التي يقدمها مترجم محترف. تخلي Cisco Systems مسئوليتها عن دقة هذه الترجمات وتُوصي بالرجوع دائمًا إلى المستند الإنجليزي الأصلي (الرابط متوفر).
يوضح هذا المستند كيفية أستكشاف أخطاء بروتوكول تحليل العنوان (ARP) وإصلاحها في بنية وصول SD.
توصي Cisco بأن تكون لديك معرفة بالمواضيع التالية:
تستند المعلومات الواردة في هذا المستند إلى إصدارات البرامج والمكونات المادية التالية:
تم إنشاء المعلومات الواردة في هذا المستند من الأجهزة الموجودة في بيئة معملية خاصة. بدأت جميع الأجهزة المُستخدمة في هذا المستند بتكوين ممسوح (افتراضي). إذا كانت شبكتك قيد التشغيل، فتأكد من فهمك للتأثير المحتمل لأي أمر.
هذا وثيقة يستطيع أيضا كنت استعملت مع هذا جهاز وبرمجية صيغة:
في هذا التمرين:
يتم عرض حالتي إستخدام رئيسيتين في هذا المستند:
في نطاق SDA، هناك طريقتان رئيسيتان لحل ARP داخل البنية. يشير ما يشار إليه باسم مسار البث الأحادي إلى أنه لا يوجد تكوين لتغمر ARP للطبقة 2 (L2) أو نقص "Flood arp and" الذي تم تكوينه تحت معرف مثيل L2 ل LISP (IID) الذي يتوافق مع شبكة VLAN المعنية. بالإضافة إلى هذا التحذير، للتأهل لمسار ARP للبث الأحادي، لا يوجد تكوين ل "IP للوكيل المحلي ARP" أو لا يوجد لتجمع الطبقة 3 فقط.
إذا تم تلبية هذه التنبيهات، فتابع مع قسم أستكشاف الأخطاء وإصلاحها هذا ويفترض أن كلا نقطتي النهاية (10.47.4.2 و 10.47.4.3) يمكن أن تصل إلى العبارات الافتراضية الخاصة بهما الموجودة على محولات Fabric Edge الموجودة على أنها 10.47.4.1
Edge-1#ping vrf red_vn 10.47.4.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.47.4.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 257/292/344 ms
Edge-2#ping vrf red_vn 10.47.4.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.47.4.3, timeout is 2 seconds: !!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 221/321/566 ms
تلميح: يوصى بإختبار اتصال البوابة الافتراضية من المضيف النهائي إلى المحول الطرفي، وليس بالطريقة الأخرى المستديرة لتجنب الاستنتاجات الخاطئة المتعلقة بحزم ICMP التي يتم إسقاطها بواسطة جدار حماية على جهاز المضيف الطرفي.
بعد ذلك، تحقق من أن كل عقدة Fabric Edge لها نقطة نهاية خاصة بها داخل تعقب أجهزة IP، (IPDT) قاعدة بيانات LISP L2، قاعدة بيانات دقة العنوان L2 (AR)، وقاعدة بيانات L3.
Edge-1:
للتحقق من نقطة النهاية داخل IPDT، أستخدم الأمر show device-tracking database interface <interface connected to endpoint>
Edge-1#show device-tracking database interface g1/0/3 portDB has 2 entries for interface Gi1/0/3, 2 dynamic Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created Preflevel flags (prlvl): 0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned Network Layer Address Link Layer Address Interface vlan prlvl age state Time left DH4 10.47.4.2 5254.0019.93e9 Gi1/0/3 1026 0024 15s REACHABLE 228 s try 0(6374 s)
للتحقق من نقطة النهاية في قاعدة بيانات LISP L2، أستخدم الأمر show lisp eid-table vlan <vlan id> قاعدة بيانات إيثرنت <mac address>أستخدم شبكة VLAN وعنوان MAC من الأمر السابق
Edge-1#show lisp eid-table vlan 1026 ethernet database 5254.0019.93e9 LISP ETR MAC Mapping Database for LISP 0 EID-table Vlan 1026 (IID 8190), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 2 5254.0019.93e9/48, dynamic-eid Auto-L2-group-8190, inherited from default locator-set rloc_222e1707-175d-4019-a783-060404f8bc2f Uptime: 3w5d, Last-change: 3w5d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.12 10/10 cfg-intf site-self, reachable <-- Edge-1's RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w3d Yes 0 10.47.1.11 3w5d Yes 0
للتحقق من أن قاعدة بيانات L2 AR تستخدم الأمر show lisp eid-table vlan <vlan-id> عنوان قاعدة بيانات الإيثرنت-الدقة <mac address>
Edge-1#show lisp eid-table vlan 1026 ethernet database address-resolution 5254.0019.93e9 LISP ETR Address Resolution for LISP 0 EID-table Vlan 1026 (IID 8190) (*) -> entry being deleted Hardware Address L3 InstID Host Address 5254.0019.93e9 4099 10.47.4.2/32 <-- Endpoint MAC address, LISP L3 IID, and IPv4 address, respectively
للتحقق من قاعدة بيانات LISP L3، أستخدم الأمر show lisp instance-id <L3 IID> IPv4 قاعدة بيانات <IPv4 address>/قناع الشبكة الفرعية أستخدم LISP L3 IID من الأمر السابق
Edge-1#show lisp instance-id 4099 ipv4 database 10.47.4.2/32 LISP ETR IPv4 Mapping Database for LISP 0 EID-table vrf red_vn (IID 4099), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 1 10.47.4.2/32, dynamic-eid red-IPV4, inherited from default locator-set rloc_222e1707-175d-4019-a783-060404f8bc2f Uptime: 3w5d, Last-change: 3w5d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.12 10/10 cfg-intf site-self, reachable <-- Edge-1's own RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w0d Yes 0 10.47.1.11 1w0d Yes 0
Edge-2:
للتحقق من نقطة النهاية داخل IPDT، أستخدم الأمر show device-tracking database interface <interface connected to local endpoint>
Edge-2#show device-tracking database interface g1/0/3 portDB has 3 entries for interface Gi1/0/3, 3 dynamic Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created Preflevel flags (prlvl): 0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned Network Layer Address Link Layer Address Interface vlan prlvl age state Time left DH4 10.47.4.3 5254.001e.ad00 Gi1/0/3 1026 0024 122s REACHABLE 124 s try 0(5810 s)
للتحقق من نقطة النهاية في قاعدة بيانات LISP L2، أستخدم الأمر show lisp eid-table vlan <vlan id> قاعدة بيانات إيثرنت <mac address> أستخدم شبكة VLAN وعنوان MAC من الأمر السابق
Edge-2#show lisp eid-table vlan 1026 ethernet database 5254.001e.ad00 LISP ETR MAC Mapping Database for LISP 0 EID-table Vlan 1026 (IID 8190), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 2 5254.001e.ad00/48, dynamic-eid Auto-L2-group-8190, inherited from default locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51 Uptime: 3w5d, Last-change: 3w5d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.13 10/10 cfg-intf site-self, reachable <-- Edge-2's RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w2d Yes 0 10.47.1.11 1w2d Yes 0
للتحقق من أن قاعدة بيانات L2 AR تستخدم الأمر show lisp eid-table vlan <vlan-id> عنوان قاعدة بيانات الإيثرنت-الدقة <mac address>
Edge-2#show lisp eid-table vlan 1026 ethernet database address-resolution 5254.001e.ad00 LISP ETR Address Resolution for LISP 0 EID-table Vlan 1026 (IID 8190) (*) -> entry being deleted Hardware Address L3 InstID Host Address 5254.001e.ad00 4099 10.47.4.3/32 <-- Endpoint MAC address, LISP L3 IID, and IPv4 address, respectively
للتحقق من قاعدة بيانات LISP L3، أستخدم الأمر show lisp instance-id <L3 IID> IPv4 قاعدة بيانات <IPv4 address>/قناع الشبكة الفرعية أستخدم LISP L3 IID من الأمر السابق
Edge-2#show lisp instance-id 4099 ipv4 database 10.47.4.3/32 LISP ETR IPv4 Mapping Database for LISP 0 EID-table vrf ed_vn (IID 4099), LSBs: 0x1 Entries total 1, no-route 0, inactive 0, do-not-register 2 10.47.4.3/32, dynamic-eid red-IPV4, inherited from default locator-set rloc_691b1fe4-5264-44c2-bb1b-0903b3eb2c51 Uptime: 1w0d, Last-change: 1w0d Domain-ID: local Service-Insertion: N/A Locator Pri/Wgt Source State 10.47.1.13 10/10 cfg-intf site-self, reachable <-- Edge-2, RLOC Map-server Uptime ACK Domain-ID 10.47.1.10 1w0d Yes 0 10.47.1.11 1w0d Yes 0
حدود مشتركة:
يتم تسجيل نقطتي النهاية بشكل مثالي من منظور L2 LISP و L2 AR و L3 إلى كل من مستويات التحكم في البنية (border-1 و border-2). لاستخلاص معرف فئة L2 LISP، تحقق من عقدة حافة البنية واستخدم الأمر show vlan id <vlan id>
Edge-1#show vlan id 1026 VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1026 red active L2LI0:8190, Gi1/0/3 <-- L2 LISP IID VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1026 enet 101026 1500 - - - - - 0 0 Remote SPAN VLAN ---------------- Disabled Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------
أستخدم معرف L2 في الأمر show lisp instance-id <L2 IID> خادم إيثرنت للتحقق من الخادم من منظور LISP من المستوى الثاني
Border-1#show lisp instance-id 8190 ethernet server LISP Site Registration Information * = Some locators are down or unreachable # = Some registrations are sourced by reliable transport Site Name Last Up Who Last Inst EID Prefix Register Registered ID site_uci never no -- 8190 any-mac 1w3d yes# 10.47.1.12:21038 8190 5254.0019.93e9/48 <-- RLOC of the FE node, EID prefix that was registered 1w2d yes# 10.47.1.13:16056 8190 5254.001e.ad00/48 <-- RLOC of the FE node, EID prefix that was registered
للتحقق من خادم L2 AR، أستخدم الأمر show lisp instance-id <L2 IID> دقة عنوان خادم الإيثرنت
Border-1#show lisp instance-id 8190 ethernet server address-resolution Address-resolution data for router lisp 0 instance-id 8190 L3 InstID Host Address Hardware Address 4099 10.47.4.2/32 5254.0019.93e9 <-- L3 LISP IID, Endpoint IPv4 Address, MAC Address, respectively 4099 10.47.4.3/32 5254.001e.ad00 <-- L3 LISP IID, Endpoint IPv4 Address, MAC Address, respectively
للتحقق من خادم L3، أستخدم الأمر show lisp instance-id <L3 IID> IPv4
Border-1#show lisp instance-id 4099 ipv4 server LISP Site Registration Information * = Some locators are down or unreachable # = Some registrations are sourced by reliable transport Site Name Last Up Who Last Inst EID Prefix Register Registered ID site_uci never no -- 4099 0.0.0.0/0 6d01h yes# 10.47.1.11:22876 4099 8.8.8.8/32 1w0d yes# 10.47.1.10:21610 4099 10.47.2.4/30 1w0d yes# 10.47.1.11:22876 4099 10.47.2.12/30 never no -- 4099 10.47.4.0/24 1w0d yes# 10.47.1.12:21038 4099 10.47.4.2/32 1w0d yes# 10.47.1.13:16056 4099 10.47.4.3/32 1w0d yes# 10.47.1.11:22876 4099 10.47.6.0/24 1w0d yes# 10.47.1.11:22876 4099 10.47.7.0/24 1w0d yes# 10.47.1.11:22876 4099 10.47.9.8/29 never no -- 4099 10.47.10.0/24 1w0d yes# 10.47.1.13:16056 4099 10.47.10.2/32
تحتوي مستويات التحكم على محفوظات موجزة لأحداث التسجيل لإدخالات L3 و L2 و AR، والتي يمكن أن تكون مفيدة عند أستكشاف أخطاء العملاء المتجولين وإصلاحها أو قد تكون حلقة عمل حيث يتم تسجيل العملاء بشكل غير متوقع بواسطة عدة حواف نسيج في وقت قصير جدا.
Border-1#show lisp instance-id 8190 ethernet server resolution registration-history | include Timestamp|10.47.4.2|10.47.4.3 Timestamp (UTC) Instance Proto Roam WLC Source *Oct 9 19:14:39.183 8190 TCP No No 10.47.1.12 +*10.47.4.2/32 / 5254.0019.93e9 <-- Last registered at Oct 9 19:14:39
*Oct 9 19:14:41.183 8190 TCP No No 10.47.1.13
+*10.47.4.3/32 / 5254.001e.ad00 <-- Last registered at OCt 9 19:14:31
ترسل نقطة النهاية التي تملك عنوان IP 10.47.4.2 طلب ARP للبث، تأكيد عبر التقاط حزمة مضمن (EPC) على Edge-1
Edge-1#monitor capture 1 interface g1/0/3 in match any Edge-1#monitor capture 1 start Edge-1#monitor capture 1 stop Capture statistics collected at software: Capture duration - 39 seconds Packets received - 21 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1 Edge-1#show monitor capture 1 buffer brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit 1 0.000000 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4. Edge-1#show monitor capture 1 buffer detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 1: 60 bytes on wire (480 bits), 60 bytes captured (480 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 19, 2023 23:43:31.893095000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1697759011.893095000 seconds [Time delta from previous captured frame: 0.000000000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 0.000000000 seconds] Frame Number: 1 Frame Length: 60 bytes (480 bits) Capture Length: 60 bytes (480 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:arp] Ethernet II, Src: 52:54:00:19:93:e9 (52:54:00:19:93:e9), Dst: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) Destination: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) Address: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast) Source: 52:54:00:19:93:e9 (52:54:00:19:93:e9) Address: 52:54:00:19:93:e9 (52:54:00:19:93:e9) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: ARP (0x0806) Padding: 000000000000000000000000000000000000 Address Resolution Protocol (request) Hardware type: Ethernet (1) Protocol type: IPv4 (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (1) Sender MAC address: 52:54:00:19:93:e9 (52:54:00:19:93:e9) Sender IP address: 10.47.4.2 Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00) Target IP address: 10.47.4.3
يتم توجيه طلب ARP هذا إلى وحدة المعالجة المركزية لمزيد من المعالجة. الاستفادة من ميزة التقاط المنتج من FED للحصول على معلومات إضافية.
Edge-1#debug platform software fed switch active punt packet-capture set-filter “arp" Edge-1#debug platform software fed switch active punt packet-capture start Edge-1#debug platform software fed switch active punt packet-capture stop Edge-1#show platform software fed switch active punt packet-capture brief Punt packet capturing: disabled. Buffer wrapping: disabled Total captured so far: 8 packets. Capture capacity : 4096 packets Capture filter : "arp" ------ Punt Packet Number: 1, Timestamp: 2023/10/19 23:55:03.552 ------ interface : physical: GigabitEthernet1/0/3[if-id: 0x0000000b], pal: GigabitEthernet1/0/3 [if-id: 0x0000000b] <-- Physical interface the ARP Request was received from metadata : cause: 109 [snoop packets], sub-cause: 1, q-no: 16, linktype: MCP_LINK_TYPE_IP [1] <-- Punted for cause snoop packets to CPU queue 16 ether hdr : dest mac: ffff.ffff.ffff, src mac: 5254.0019.93e9 ether hdr : ethertype: 0x0806 (ARP)
لرؤية قائمة انتظار وحدة المعالجة المركزية (CPU) رقم 16، أستخدم الأمر show platform software switch active punt cpuq 16
Edge-1#show platform software fed switch active punt cpuq 16 Punt CPU Q Statistics =========================================== CPU Q Id : 16 CPU Q Name : CPU_Q_PROTO_SNOOPING Packets received from ASIC : 49054 Send to IOSd total attempts : 49054 <-- Same number as received from ASIC
Send to IOSd failed count : 0 <-- No failures
وبشكل مثالي، لا توجد حالات إسقاط في قائمة انتظار التطفل على بروتوكول Proto في منظم وحدة المعالجة المركزية (قائمة الانتظار 16)، أستخدم الأمر show platform hardware fed switch نشط حالة قائمة انتظار جودة الخدمة (CPU) الداخلية واضع سياسات وحدة المعالجة المركزية
Edge-1#show platform hardware fed switch active qos queue stats internal cpu policer | include QId|Proto QId PlcIdx Queue Name Enabled Rate Rate Drop(Bytes) Drop(Frames) 16 12 Proto Snooping No 2000 2000 0 0 <-- No drops
بعد ذلك، تتم معالجة طلب ARP المثقل بواسطة خدمة Punt. يمكنك رؤية هذا السلوك باستخدام مجموعة تصحيح الأخطاء والبنية الأساسية لبرنامج منصة تصحيح الأخطاء
Edge-1#debug platform software infrastructure punt
*Oct 20 00:07:01.509: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 20 00:07:01.509: Punt: IP proto src 147.233.10.47, dst 4.2.0.0, from table 0, intf Gi1/0/3, encap ARPA, size 60, cause snoop packets(L3) <-- The IP address is obscured, but it is 10.47.4.2 *Oct 20 00:07:01.509: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 20 00:07:01.509: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
تحذير: تصحيح الأخطاء هذا هو الثرثرة، الاستخدام بحذر.
بعد أن تقوم خدمة التجميع بمعالجة الحزمة، فإنها تسلم الحزمة إلى عمليتي التطفل على Proto SNOOP و Proto ARP. وهذا يؤدي إلى إنشاء إدخال في جدول التطفل على بروتوكول تحليل العناوين (ARP) ويتم إرسال الحزمة إلى تعقب الأجهزة/ISF. لرؤية ذلك، debug arp بالإضافة إلى منصة تصحيح الأخطاء لجميع
Edge-1#debug arp
Edge-1#debug platform fhs all
*Oct 20 00:12:06.908: ARP packet received from ARP snooper(Gi1/0/3 10.47.4.2 (5254.0019.93e9) VLAN:1026)
تحذير: هذه الأخطاء عبارة عن دردشة، أستخدم بحذر
أستخدم الأمر show platform arpsnooping client <MAC address> للاطلاع على ما يحدث لطلب ARP
Edge-1#show platform arpsnooping client 5254.0019.93e9 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.0019.93E9: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------ 2023/10/24 14:37:15.045 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PSISF_PRE:PSP_BRNEUTRAL 2023/10/24 14:37:15.045 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 14:37:15.045 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:BD_DPIDX_TO_FWDPLANE
بينما يقوم IPDT/SIF بمعالجة الحزمة، فإنه يتحقق من محتويات طلب ARP وينشئ إدخالا مؤقتا بينما ينتظر الحل عبر LISP.
Edge-1#show device-tracking messages detailed 255 | i 5254.0019.93e9 [Tue Oct 24 14:37:12.000] VLAN 1026, From Gi1/0/3 seclvl [guard], MAC 5254.0019.93e9: ARP::REQ, [Tue Oct 24 14:37:13.000] VLAN 1026, From Gi1/0/3 seclvl [guard], MAC 5254.0019.93e9: ARP::REQ,
إذا كنت تستخدم تتبع أجهزة تصحيح الأخطاء فأنك ترى أن هناك إدخال يشير نحو 000.000.00fd في تعقب الأجهزة. كل هذا يعني أن المضيف الموجود خلف Gi1/0/3 يستعلم عن مضيف لم يتم حله بعد، فهو في حالة انتقالية (أو دائم في حالة الاستعلام عن مضيف غير موجود، وهذا ليس بالضرورة أمرا سيئا)
Edge-1#debug device-tracking Device-tracking - General debugging is on *Oct 24 14:55:02.967: SISF[POL]: vlan 1026 matches vlan list on policy IPDT_POLICY for target Gi1/0/3 *Oct 24 14:55:02.967: SISF[POL]: Found matching policy IPDT_POLICY for feature Device-tracking on Gi1/0/3
*Oct 24 14:55:02.967:SISF[GLN]: Checking if ARP ownership can be taken by device-tracking
*Oct 24 14:55:02.967:SISF[GLN]: Not an ARP reply, do not take over
*Oct 24 14:55:02.967:SISF[POL]: Found matching policy LISP-AR-RELAY-VLAN for feature Address Resolution Relay on vlan 1026 *Oct 24 14:55:02.967: SISF[MAC]: Creating new MAC entry for 0000.0000.00fd on interface if none exists *Oct 24 14:55:02.967: SISF[MAC]: Number of MAC entries in MAC-CREATING state incremented to 1 *Oct 24 14:55:02.968: SISF[BT ]: Attaching 0000.0000.00fd entry in MacAdrDB for 10.47.4.3 *Oct 24 14:55:02.968: SISF[GLN]: Binding entry event 1 for 10.47.4.3
تقوم SIF بتشغيل تحليل ARP باستخدام LISP بسبب سياسة LISP-AR-RELAY-VLAN، بعد أن تتمكن عمليات التحكم في مستوى تحكم LISP من تولي الأمر.
Edge-1#debug lisp control-plane all Edge-1#debug l2lisp all *Oct 24 15:10:27.677: LISP Client 'SISF client': SISF request to resolve 10.47.4.3 in Vlan 1026.
يرسل Edge-1 طلب خريطة LISP لحل عنوان MAC الخاص ب 10.47.4.3 من خلال LISP Control-Plane (مستوى)
Edge-1#debug lisp control-plane all Edge-1#debug l2lisp all *Oct 24 15:10:27.681: LISP[REMT ]-0: Map Request: Delay is over for IID 8190 EID 10.47.4.3/32, requester 'AR'. *Oct 24 15:10:27.681: LISP[REMT ]-0 IID 8190: Schedule processing of Map-Requests from 'remote EID prefix' in IPv4. *Oct 24 15:10:27.681: LISP[REMT ]-0: Map Request: Sending request for IID 8190 EID 10.47.4.3/32, requester 'AR'.
يوضح التقاط الحزمة المضمنة ثنائي الإتجاه (EPC) الذي يتم بواسطة وحدة المعالجة المركزية (مستوى التحكم) في Edge-1 طلب ARP الوارد وطلب خريطة LISP اللاحق
Edge-1#monitor capture 1 control-plane both match any Edge-1#monitor capture 1 start Started capture point : 1 Edge-1#monitor capture 1 stop Edge-1#show monitor capture 1 buffer display-filter "arp.dst.proto_ipv4==10.47.4.3 or lisp" Starting the packet display ........ Press Ctrl + Shift + 6 to exit 60 10.110293 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 61 10.111714 10.47.4.3 -> 10.47.4.3 LISP 114 Encapsulated Map-Request for Unknown LCAF Type (53)/32
يمكنك أخذ عرض أكثر تفصيلا لطلب خريطة LISP
Edge-1#show monitor capture 1 buffer display-filter "frame.number==61" detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 61: 114 bytes on wire (912 bits), 114 bytes captured (912 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 24, 2023 15:20:08.948469000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698160808.948469000 seconds [Time delta from previous captured frame: 0.001421000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 10.111714000 seconds] Frame Number: 61 Frame Length: 114 bytes (912 bits) Capture Length: 114 bytes (912 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:lisp:ip:udp:lisp] Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) <-- Ignore the SMAC/DMAC this is done up at the CPU, not final MAC addresses Destination: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.10 <-- Edge-1 RLOC and one of the collocated border RLOC, respectively 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 100 Identification: 0x599c (22940) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x4ab9 [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.12 Destination: 10.47.1.10 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 80 Checksum: 0x6393 [unverified] [Checksum Status: Unverified] [Stream index: 0] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Locator/ID Separation Protocol 1000 .... .... .... .... .... = Type: Encapsulated Control Message (8) .... 0... .... .... .... .... .... .... = S bit (LISP-SEC capable): Not set .... .0.. .... .... .... .... .... .... = D bit (DDT-originated): Not set .... ..00 0000 0000 0000 0000 0000 0000 = Reserved bits: 0x0000000 Internet Protocol Version 4, Src: 10.47.4.3, Dst: 10.47.4.3 <-- MAP Request to resolve the MAC address tied to 10.47.4.3 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 68 Identification: 0x599b (22939) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x44ea [validation disabled] [Header checksum status: Unverified] Source: 10.47.4.3 Destination: 10.47.4.3 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 48 Checksum: 0x9622 [unverified] [Checksum Status: Unverified] [Stream index: 1] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Locator/ID Separation Protocol 0001 .... .... .... .... .... = Type: Map-Request (1) .... 0000 00.. .... .... .... = Flags: 0x00 .... 0... .... .... .... .... = A bit (Authoritative): Not set .... .0.. .... .... .... .... = M bit (Map-Reply present): Not set .... ..0. .... .... .... .... = P bit (Probe): Not set .... ...0 .... .... .... .... = S bit (Solicit-Map-Request): Not set .... .... 0... .... .... .... = p bit (Proxy ITR): Not set .... .... .0.. .... .... .... = s bit (SMR-invoked): Not set .... .... ..00 0000 000. .... = Reserved bits: 0x000 .... .... .... .... ...0 0000 = ITR-RLOC Count: 0 Record Count: 1 Nonce: 0xcffee30fb39a05b7 Source EID AFI: Reserved (0) Source EID: not set ITR-RLOC 1: 10.47.1.12 ITR-RLOC AFI: IPv4 (1) ITR-RLOC Address: 10.47.1.12 Map-Request Record 1: Unknown LCAF Type (53)/32 Reserved: 0x00 Prefix Length: 32 Prefix AFI: LISP Canonical Address Format (LCAF) (16387) Prefix: Unknown LCAF Type (53) LCAF: Unknown (53) LCAF Header: 00003520000a Reserved bits: 0x00 Flags: 0x00 Type: Unknown (53) Reserved bits: 0x20 Length: 10 [Expert Info (Error/Protocol): LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05] [LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05] [Severity level: Error] [Group: Protocol]
بعد ذلك، يستجيب مستوى التحكم في LISP إلى edge-1 باستخدام رد على خريطة LISP. ويمكن ملاحظة ذلك في تصحيح الأخطاء وكذلك CPU EPC.
Border-2#show monitor capture 1 buffer display-filter lisp Starting the packet display ........ Press Ctrl + Shift + 6 to exit 113 12.767420 10.47.4.3 -> 10.47.4.3 LISP 114 Encapsulated Map-Request for Unknown LCAF Type (53)/32 114 12.774428 10.47.1.11 -> 10.47.1.12 LISP 96 Map-Reply for Unknown LCAF Type (53)/32
بينما ننظر إلى الحزم بمزيد من التفاصيل، يمكننا مشاهدة طلب خريطة LISP ورد خريطة LISP اللاحق
Border-2#show monitor capture 1 buffer display-filter frame.number==113 detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 113: 114 bytes on wire (912 bits), 114 bytes captured (912 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 24, 2023 15:41:06.566253000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698162066.566253000 seconds [Time delta from previous captured frame: 0.013424000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 12.767420000 seconds] Frame Number: 113 Frame Length: 114 bytes (912 bits) Capture Length: 114 bytes (912 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:lisp:ip:udp:lisp] Ethernet II, Src: 52:54:00:04:84:a3 (52:54:00:04:84:a3), Dst: 52:54:00:1c:7d:e0 (52:54:00:1c:7d:e0) <-- True MAC addresses Destination: 52:54:00:1c:7d:e0 (52:54:00:1c:7d:e0) Address: 52:54:00:1c:7d:e0 (52:54:00:1c:7d:e0) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 52:54:00:04:84:a3 (52:54:00:04:84:a3) Address: 52:54:00:04:84:a3 (52:54:00:04:84:a3) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.11 <-- Edge-1 RLOC and Border-2 RLOC, respectively 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 100 Identification: 0x5e19 (24089) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x463b [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.12 Destination: 10.47.1.11 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 80 Checksum: 0x6392 [unverified] [Checksum Status: Unverified] [Stream index: 1] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Locator/ID Separation Protocol 1000 .... .... .... .... .... = Type: Encapsulated Control Message (8) .... 0... .... .... .... .... .... .... = S bit (LISP-SEC capable): Not set .... .0.. .... .... .... .... .... .... = D bit (DDT-originated): Not set .... ..00 0000 0000 0000 0000 0000 0000 = Reserved bits: 0x0000000 Internet Protocol Version 4, Src: 10.47.4.3, Dst: 10.47.4.3 <-- LISP MAP Request for 10.47.4.3 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 68 Identification: 0x5e18 (24088) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x406d [validation disabled] [Header checksum status: Unverified] Source: 10.47.4.3 Destination: 10.47.4.3 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 48 Checksum: 0xe9a8 [unverified] [Checksum Status: Unverified] [Stream index: 2] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Locator/ID Separation Protocol 0001 .... .... .... .... .... = Type: Map-Request (1) .... 0000 00.. .... .... .... = Flags: 0x00 .... 0... .... .... .... .... = A bit (Authoritative): Not set .... .0.. .... .... .... .... = M bit (Map-Reply present): Not set .... ..0. .... .... .... .... = P bit (Probe): Not set .... ...0 .... .... .... .... = S bit (Solicit-Map-Request): Not set .... .... 0... .... .... .... = p bit (Proxy ITR): Not set .... .... .0.. .... .... .... = s bit (SMR-invoked): Not set .... .... ..00 0000 000. .... = Reserved bits: 0x000 .... .... .... .... ...0 0000 = ITR-RLOC Count: 0 Record Count: 1 Nonce: 0x50c5f2b60b41ca1c Source EID AFI: Reserved (0) Source EID: not set ITR-RLOC 1: 10.47.1.12 ITR-RLOC AFI: IPv4 (1) ITR-RLOC Address: 10.47.1.12 Map-Request Record 1: Unknown LCAF Type (53)/32 Reserved: 0x00 Prefix Length: 32 Prefix AFI: LISP Canonical Address Format (LCAF) (16387) Prefix: Unknown LCAF Type (53) LCAF: Unknown (53) LCAF Header: 00003520000a Reserved bits: 0x00 Flags: 0x00 Type: Unknown (53) Reserved bits: 0x20 Length: 10 [Expert Info (Error/Protocol): LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05] [LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05] [Severity level: Error] [Group: Protocol]
كما يمكننا الاطلاع على الرد على خريطة LISP التي يتم إرسالها مرة أخرى
Border-2#show monitor capture 1 buffer display-filter frame.number==114 detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 114: 96 bytes on wire (768 bits), 96 bytes captured (768 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 24, 2023 15:41:06.573261000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698162066.573261000 seconds [Time delta from previous captured frame: 0.007008000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 12.774428000 seconds] Frame Number: 114 Frame Length: 96 bytes (768 bits) Capture Length: 96 bytes (768 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:lisp] Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) <-- CPU Inject does not properly show MAC addresses Destination: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.11, Dst: 10.47.1.12 <-- Border-2 RLOC and Edge-1 RLOC, respectively 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 82 Identification: 0xe231 (57905) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0xc234 [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.11 Destination: 10.47.1.12 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 62 Checksum: 0xe1d6 [unverified] [Checksum Status: Unverified] [Stream index: 1] [Timestamps] [Time since first frame: 0.007008000 seconds] [Time since previous frame: 0.007008000 seconds] Locator/ID Separation Protocol 0010 .... .... .... .... .... = Type: Map-Reply (2) .... 0... .... .... .... .... = P bit (Probe): Not set .... .0.. .... .... .... .... = E bit (Echo-Nonce locator reachability algorithm enabled): Not set .... ..0. .... .... .... .... = S bit (LISP-SEC capable): Not set .... ...0 0000 0000 0000 0000 = Reserved bits: 0x00000 Record Count: 1 Nonce: 0x50c5f2b60b41ca1c Mapping Record 1, EID Prefix: Unknown LCAF Type (53)/32, TTL: 1440, Action: No-Action, Not Authoritative Record TTL: 1440 Locator Count: 1 EID Mask Length: 32 000. .... .... .... = Action: No-Action (0) ...0 .... .... .... = Authoritative bit: Not set .... .000 0000 0000 = Reserved: 0x000 0000 .... .... .... = Reserved: 0x0 .... 0000 0000 0000 = Mapping Version: 0 EID Prefix AFI: LISP Canonical Address Format (LCAF) (16387) EID Prefix: Unknown LCAF Type (53) LCAF: Unknown (53) LCAF Header: 00003520000a Reserved bits: 0x00 Flags: 0x00 Type: Unknown (53) Reserved bits: 0x20 Length: 10 [Expert Info (Error/Protocol): LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05] [LCAF type 53 is not defined in draft-ietf-lisp-lcaf-05] [Severity level: Error] [Group: Protocol] Locator Record 1, RLOC: 52:54:00:1e:ad:00, Unreachable, Priority/Weight: 1/100, Multicast Priority/Weight: 1/100 Priority: 1 Weight: 100 Multicast Priority: 1 Multicast Weight: 100 Flags: 0x0000 0000 0000 0000 0... = Reserved: 0x0000 .... .... .... .0.. = Local: Not set .... .... .... ..0. = Probe: Not set .... .... .... ...0 = Reachable: Not set AFI: 802 (includes all 802 media plus Ethernet) (6) Locator: 52:54:00:1e:ad:00
Border-2#debug lisp control-plane all All LISP control debugging is on at verbose level Border-2#debug l2lisp all All L2Lisp debugging is on *Oct 24 16:02:17.854: LISP[TRNSP]-0: Processing received Encap-Control(8) message on GigabitEthernet1/0/3 from 10.47.1.12:4342 to 10.47.1.11:4342. *Oct 24 16:02:17.854: LISP[TRNSP]-0: Processing received Map-Request(1) message on GigabitEthernet1/0/3 from 10.47.4.3:4342 to 10.47.4.3:4342. *Oct 24 16:02:17.855: LISP[MR ]-0: Received Map-Request with 1 records, first EID IID 8190 10.47.4.3/32, source EID UNSPEC, nonce 0x3847C91F-0xA966DDEA. *Oct 24 16:02:17.855: LISP[MR ]-0 IID 8190 Eth-ARP: MS EID 10.47.4.3/32: Sending proxy reply to 10.47.1.12.
الآن وقد تلقى Edge-1 رد خريطة LISP لطلب تحليل العنوان (AR) قائلا إن 10.47.4.3 هي 5254.001e.ad00، ينتج Edge-1 طلب خريطة LISP آخر لتحديد RLOC لعنوان MAC لنقطة النهاية
Edge-1#debug lisp control-plane all
Edge-1#debug l2lisp all
*Oct 24 16:19:54.843: LISP[REMT ]-0: Received Map-Reply with nonce 0x37F890B9-0xAC60D2B9, 1 records.
*Oct 24 16:19:54.843: LISP[MS ]-0: This is a Address Resolution message.
*Oct 24 16:19:54.843: LISP[REMT ]-0: Map-Reply nonce matches pending request for IID 8190 EID 10.47.4.3/32, requester 'AR'.
*Oct 24 16:19:54.843: LISP[REMT ]-0: Processing Map-Reply mapping record for IID 8190 Eth-ARP 10.47.4.3/32 LCAF 53, ttl 1440, action none, not authoritative, 1 locator.
*Oct 24 16:19:54.843: LISP[REMT ]-0: 5254.001e.ad00 pri/wei/dID/mID/met/si_type/si_id/si_flg/afn_id=1/100/0/0/4294967295/none/0/UNSPEC/UNSPEC lpr.
*Oct 24 17:11:24.056: LISP[REMT ]-0 IID 8190: Schedule processing of Map-Requests from 'remote EID prefix' in IPv4. *Oct 24 17:11:24.056: LISP[REMT ]-0:
Map Request: Sending request for IID 8190 EID 5254.001e.ad00/48, requester 'remote EID prefix'.>
يستقبل LISP Control-Plane طلب خريطة LISP، الخاص بعنوان MAC 10.47.4.3، ويستشير جدول خادم الإيثرنت ل L2 LISP IID 8190 ويرسل رد خريطة LISP مع ربط MAC-RLOC
Border-1#show monitor capture 1 buff display-filter lisp brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit
250 28.656076 0.0.0.0 -> 0.0.0.0 LISP 176 Encapsulated Map-Request for [8190] 52:54:00:1e:ad:00/48 251 28.658851 10.47.1.10 -> 10.47.1.12 LISP 96 Map-Reply for [8190] 52:54:00:1e:ad:00/48
يمكننا إلقاء نظرة عن كثب على طلب خريطة LISP و Map-Reply
Border-1#show monitor capture 1 buffer display-filter frame.number==250 detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 250: 176 bytes on wire (1408 bits), 176 bytes captured (1408 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 24, 2023 17:37:11.647755000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698169031.647755000 seconds [Time delta from previous captured frame: 0.315724000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 28.656076000 seconds] Frame Number: 250 Frame Length: 176 bytes (1408 bits) Capture Length: 176 bytes (1408 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:lisp:ip:udp:lisp] Ethernet II, Src: 52:54:00:04:84:b1 (52:54:00:04:84:b1), Dst: 52:54:00:0a:42:f3 (52:54:00:0a:42:f3) Destination: 52:54:00:0a:42:f3 (52:54:00:0a:42:f3) Address: 52:54:00:0a:42:f3 (52:54:00:0a:42:f3) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 52:54:00:04:84:b1 (52:54:00:04:84:b1) Address: 52:54:00:04:84:b1 (52:54:00:04:84:b1) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.10 <-- Edge-1 RLOC and Border-1 RLOC, respectively 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 162 Identification: 0x75e5 (30181) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x2e32 [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.12 Destination: 10.47.1.10 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 142 Checksum: 0x46f1 [unverified] [Checksum Status: Unverified] [Stream index: 4] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Locator/ID Separation Protocol 1000 .... .... .... .... .... = Type: Encapsulated Control Message (8) .... 0... .... .... .... .... .... .... = S bit (LISP-SEC capable): Not set .... .0.. .... .... .... .... .... .... = D bit (DDT-originated): Not set .... ..00 0000 0000 0000 0000 0000 0000 = Reserved bits: 0x0000000 Internet Protocol Version 4, Src: 0.0.0.0, Dst: 0.0.0.0 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 130 Identification: 0x75e4 (30180) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x44c7 [validation disabled] [Header checksum status: Unverified] Source: 0.0.0.0 Destination: 0.0.0.0 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 110 Checksum: 0x18bb [unverified] [Checksum Status: Unverified] [Stream index: 5] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Locator/ID Separation Protocol 0001 .... .... .... .... .... = Type: Map-Request (1) .... 0100 00.. .... .... .... = Flags: 0x10 .... 0... .... .... .... .... = A bit (Authoritative): Not set .... .1.. .... .... .... .... = M bit (Map-Reply present): Set .... ..0. .... .... .... .... = P bit (Probe): Not set .... ...0 .... .... .... .... = S bit (Solicit-Map-Request): Not set .... .... 0... .... .... .... = p bit (Proxy ITR): Not set .... .... .0.. .... .... .... = s bit (SMR-invoked): Not set .... .... ..00 0000 000. .... = Reserved bits: 0x000 .... .... .... .... ...0 0000 = ITR-RLOC Count: 0 Record Count: 1 Nonce: 0x86438e956066d3ca Source EID AFI: LISP Canonical Address Format (LCAF) (16387) Source EID: [8190] 00:00:0c:9f:f3:41 LCAF: Instance ID: 8190, Address: 00:00:0c:9f:f3:41 LCAF Header: 00000220000c Reserved bits: 0x00 Flags: 0x00 Type: Instance ID (2) Reserved bits: 0x20 Length: 12 Instance ID: 8190 Address AFI: 802 (includes all 802 media plus Ethernet) (6) Address: 00:00:0c:9f:f3:41 (00:00:0c:9f:f3:41) ITR-RLOC 1: 10.47.1.12 ITR-RLOC AFI: IPv4 (1) ITR-RLOC Address: 10.47.1.12 Map-Request Record 1: [8190] 52:54:00:1e:ad:00/48 <-- Map-Request for this specific MAC address Reserved: 0x00 Prefix Length: 48 Prefix AFI: LISP Canonical Address Format (LCAF) (16387) Prefix: [8190] 52:54:00:1e:ad:00 LCAF: Instance ID: 8190, Address: 52:54:00:1e:ad:00 LCAF Header: 00000220000c Reserved bits: 0x00 Flags: 0x00 Type: Instance ID (2) Reserved bits: 0x20 Length: 12 Instance ID: 8190 Address AFI: 802 (includes all 802 media plus Ethernet) (6) Address: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00) Map-Reply Record Mapping Record 1, EID Prefix: [8190] 00:00:0c:9f:f3:41/48, TTL: 1440, Action: No-Action, Authoritative Record TTL: 1440 Locator Count: 1 EID Mask Length: 48 000. .... .... .... = Action: No-Action (0) ...1 .... .... .... = Authoritative bit: Set .... .000 0000 0000 = Reserved: 0x000 0000 .... .... .... = Reserved: 0x0 .... 0000 0000 0000 = Mapping Version: 0 EID Prefix AFI: LISP Canonical Address Format (LCAF) (16387) EID Prefix: [8190] 00:00:0c:9f:f3:41 LCAF: Instance ID: 8190, Address: 00:00:0c:9f:f3:41 LCAF Header: 00000220000c Reserved bits: 0x00 Flags: 0x00 Type: Instance ID (2) Reserved bits: 0x20 Length: 12 Instance ID: 8190 Address AFI: 802 (includes all 802 media plus Ethernet) (6) Address: 00:00:0c:9f:f3:41 (00:00:0c:9f:f3:41) Locator Record 1, Local RLOC: 10.47.1.12, Reachable, Priority/Weight: 10/10, Multicast Priority/Weight: 10/10 Priority: 10 Weight: 10 Multicast Priority: 10 Multicast Weight: 10 Flags: 0x0005 0000 0000 0000 0... = Reserved: 0x0000 .... .... .... .1.. = Local: Set .... .... .... ..0. = Probe: Not set .... .... .... ...1 = Reachable: Set AFI: IPv4 (1) Locator: 10.47.1.12
Border-1#show monitor capture 1 buffer display-filter frame.number==251 detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 251: 96 bytes on wire (768 bits), 96 bytes captured (768 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 24, 2023 17:37:11.650530000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698169031.650530000 seconds [Time delta from previous captured frame: 0.002775000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 28.658851000 seconds] Frame Number: 251 Frame Length: 96 bytes (768 bits) Capture Length: 96 bytes (768 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:lisp] Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) Destination: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.10, Dst: 10.47.1.12 <-- Border-1 RLOC, Edge-1 RLOC, respectively 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0xc0 (DSCP: CS6, ECN: Not-ECT) 1100 00.. = Differentiated Services Codepoint: Class Selector 6 (48) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 82 Identification: 0x12a9 (4777) Flags: 0x0000 0... .... .... .... = Reserved bit: Not set .0.. .... .... .... = Don't fragment: Not set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0x91be [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.10 Destination: 10.47.1.12 User Datagram Protocol, Src Port: 4342, Dst Port: 4342 Source Port: 4342 Destination Port: 4342 Length: 62 Checksum: 0xd63e [unverified] [Checksum Status: Unverified] [Stream index: 4] [Timestamps] [Time since first frame: 0.002775000 seconds] [Time since previous frame: 0.002775000 seconds] Locator/ID Separation Protocol 0010 .... .... .... .... .... = Type: Map-Reply (2) .... 0... .... .... .... .... = P bit (Probe): Not set .... .0.. .... .... .... .... = E bit (Echo-Nonce locator reachability algorithm enabled): Not set .... ..0. .... .... .... .... = S bit (LISP-SEC capable): Not set .... ...0 0000 0000 0000 0000 = Reserved bits: 0x00000 Record Count: 1 Nonce: 0x86438e956066d3ca Mapping Record 1, EID Prefix: [8190] 52:54:00:1e:ad:00/48, TTL: 1440, Action: No-Action, Not Authoritative Record TTL: 1440 Locator Count: 1 EID Mask Length: 48 000. .... .... .... = Action: No-Action (0) ...0 .... .... .... = Authoritative bit: Not set .... .000 0000 0000 = Reserved: 0x000 0000 .... .... .... = Reserved: 0x0 .... 0000 0000 0000 = Mapping Version: 0 EID Prefix AFI: LISP Canonical Address Format (LCAF) (16387) EID Prefix: [8190] 52:54:00:1e:ad:00 LCAF: Instance ID: 8190, Address: 52:54:00:1e:ad:00 LCAF Header: 00000220000c Reserved bits: 0x00 Flags: 0x00 Type: Instance ID (2) Reserved bits: 0x20 Length: 12 Instance ID: 8190 Address AFI: 802 (includes all 802 media plus Ethernet) (6) Address: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00) Locator Record 1, RLOC: 10.47.1.13, Reachable, Priority/Weight: 10/10, Multicast Priority/Weight: 10/10 Priority: 10 Weight: 10 Multicast Priority: 10 Multicast Weight: 10 Flags: 0x0001 0000 0000 0000 0... = Reserved: 0x0000 .... .... .... .0.. = Local: Not set .... .... .... ..0. = Probe: Not set .... .... .... ...1 = Reachable: Set AFI: IPv4 (1) Locator: 10.47.1.13 <-- This RLOC owns the MAC address
Border-1#debug lisp control-plane all
Border-1#debug l2lisp all
*Oct 24 18:03:00.361: LISP[TRNSP]-0: Processing received Map-Request(1) message on GigabitEthernet1/0/3 from 0.0.0.0:4342 to 0.0.0.0:4342. *Oct 24 18:03:00.361: LISP[MR ]-0: Received Map-Request with 1 records, first EID IID 8190 5254.001e.ad00/48, source EID 0000.0c9f.f341, nonce 0xAD90C521-0x348A478D. *Oct 24 18:03:00.361: LISP[MR ]-0 IID 8190 MAC: MS EID 5254.001e.ad00/48: Sending proxy reply to 10.47.1.12.
Edge-1 يستلم LISP Map-Reply من border-1
Edge-1#debug lisp control-plane all
Edge-1#debug l2lisp all
*Oct 24 17:11:24.558: LISP[TRNSP]-0: Processing received Map-Reply(2) message on GigabitEthernet1/0/1 from 10.47.1.10:4342 to 10.47.1.12:4342. *Oct 24 17:11:24.558: LISP[REMT ]-0: Received Map-Reply with nonce 0x38A78BA8-0xC378149D, 1 records. *Oct 24 17:11:24.558: LISP[REMT ]-0: Map-Reply nonce matches pending request for IID 8190 EID 5254.001e.ad00/48, requester 'remote EID prefix'. *Oct 24 17:11:24.558: LISP[REMT ]-0: Processing Map-Reply mapping record for IID 8190 MAC 5254.001e.ad00/48 LCAF 2, ttl 1440, action none, not authoritative, 1 locator. *Oct 24 17:11:24.559: LISP[REMT ]-0: 10.47.1.13 pri/wei/dID/mID/met/si_type/si_id/si_flg/afn_id=10/10/0/0/4294967295/none/0/UNSPEC/UNSPEC lpR.
يمكن عرض طلب ARP بالكامل من خلال تبادل LISP/ISF على edge-1 عبر CPU EPC
Edge-1#show monitor capture 1 buffer display-filter "arp.dst.proto_ipv4==10.47.4.3 or lisp" Starting the packet display ........ Press Ctrl + Shift + 6 to exit
120 18.415474 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 <-- Broadcast ARP Request punted up to the CPU 121 18.416092 10.47.4.3 -> 10.47.4.3 LISP 114 Encapsulated Map-Request for Unknown LCAF Type (53)/32 <-- LISP Map-Request to obtain the MAC address of 10.47.4.3 135 19.598041 10.47.1.11 -> 10.47.1.12 LISP 96 Map-Reply for Unknown LCAF Type (53)/32 <-- LISP Map-Reply providing the MAC address of 10.47.4.3 136 19.613072 0.0.0.0 -> 0.0.0.0 LISP 176 Encapsulated Map-Request for [8190] 52:54:00:1e:ad:00/48 <-- LISP Map-Request to obtain the RLOC for MAC address 5254.001e.ad00 138 20.119722 10.47.1.10 -> 10.47.1.12 LISP 96 Map-Reply for [8190] 52:54:00:1e:ad:00/48 <-- LISP Map-Reply for the RLOC that owns MAC address 5254.001e.ad00 143 20.477618 52:54:00:19:93:e9 -> 52:54:00:1e:ad:00 ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 <-- Unicast ARP Request injected down from the CPU
بمجرد تقارب مستوى التحكم على Edge-1، يوجد إدخال ذاكرة تخزين مؤقت للخرائط بالإضافة إلى الإدخال عن بعد ل ISF (RMT)
Edge-1#show lisp instance-id 8190 ethernet map-cache 5254.001e.ad00 LISP MAC Mapping Cache for LISP 0 EID-table Vlan 1026 (IID 8190), 1 entries 5254.001e.ad00/48, uptime: 00:06:26, expires: 23:53:34, via map-reply, complete Sources: map-reply State: complete, last modified: 00:06:26, map-source: 10.47.1.13 Active, Packets out: 11(0 bytes), counters are not accurate (~ 00:00:00 ago) Encapsulating dynamic-EID traffic Locator Uptime State Pri/Wgt Encap-IID 10.47.1.13 00:06:26 up 10/10 - Last up-down state change: 00:06:26, state change count: 1 Last route reachability change: 2w0d, state change count: 1 Last priority / weight change: never/never RLOC-probing loc-status algorithm: Last RLOC-probe sent: 00:06:25 (rtt 1104ms)
Edge-1#show device-tracking database address 10.47.4.3 Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created Preflevel flags (prlvl): 0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned Network Layer Address Link Layer Address Interface vlan prlvl age state Time left RMT 10.47.4.3 5254.001e.ad00 L2LI0 1026 0005 7mn STALE try 0 731 s
بعد ذلك، يتم حقن طلب ARP للبث الأحادي من وحدة المعالجة المركزية. تذكر، لا يمكن التقاط حزم CPU التي تم حقنها في إتجاه المخرج مع EPC على الواجهات المادية، يمكن إستخدام محلل منفذ Switchport (SPAN) أو مدخل EPC على عقدة حافة البنية المستلمة لتأكيد إستلام طلب VXLAN الذي تم تغليف ARP أحادي البث
أول، دققت أن ال lip أو نفق قارن مدرج في ال VLAN id إنتاج ل VLAN 1026
Edge-2#show vlan id 1026 VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1026 red active L2LI0:8190, Gi1/0/3 <-- L2 LISP IID is associated VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1026 enet 101026 1500 - - - - - 0 0 Remote SPAN VLAN ---------------- Disabled Primary Secondary Type Ports ------- --------- ----------------- ------------------------------------------
الآن، يوضح مدخل EPC على edge-2 ال VXLAN يغلف ARP رد يستلم. بما أن طلب ARP للبث الأحادي يتم تغليف VXLAN، أنت يستطيع إستعملت ip acl أن يماثل ضد Edge-1 RLOC يرسل نحو Edge-2 RLOC (10.47.1.12 باتجاه 10.47.1.13، على التوالي) أن يساعد مرشح الحركة مرور.
Edge-2(config)#ip access-list extended tac Edge-2(config-ext-nacl)#permit ip host 10.47.1.12 host 10.47.1.13
Edge-2#monitor capture 1 interface g1/0/1 in access-list tac Edge-2#monitor capture 1 interface g1/0/2 in access-list tac Edge-2#monitor capture 1 start Started capture point : 1 Edge-2#monitor capture 1 stop Capture statistics collected at software: Capture duration - 20 seconds Packets received - 10 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1
Edge-2#show monitor capture 1 buffer brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit 1 0.000000 52:54:00:19:93:e9 -> 52:54:00:1e:ad:00 ARP 110 Who has 10.47.4.3? Tell 10.47.4.2
عند فحص طلب ARP هذا بشكل أدق، يمكنك أن ترى هناك تضمين VXLAN، ورأس UDP، ورؤوس أخرى، بما أن إطار ARP صغير، 60 بايت عادة.
Edge-2#show monitor capture 1 buffer display-filter frame.number==1 detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 1: 110 bytes on wire (880 bits), 110 bytes captured (880 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 24, 2023 18:57:34.642468000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698173854.642468000 seconds [Time delta from previous captured frame: 0.000000000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 0.000000000 seconds] Frame Number: 1 Frame Length: 110 bytes (880 bits) Capture Length: 110 bytes (880 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:vxlan:eth:ethertype:arp] Ethernet II, Src: 52:54:00:0a:42:11 (52:54:00:0a:42:11), Dst: 52:54:00:17:fe:65 (52:54:00:17:fe:65) Destination: 52:54:00:17:fe:65 (52:54:00:17:fe:65) Address: 52:54:00:17:fe:65 (52:54:00:17:fe:65) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 52:54:00:0a:42:11 (52:54:00:0a:42:11) Address: 52:54:00:0a:42:11 (52:54:00:0a:42:11) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.12, Dst: 10.47.1.13 <-- Edge-1 RLOC and Edge-2 RLOC, respectively 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0x00 (DSCP: CS0, ECN: Not-ECT) 0000 00.. = Differentiated Services Codepoint: Default (0) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 96 Identification: 0x798a (31114) Flags: 0x4000, Don't fragment 0... .... .... .... = Reserved bit: Not set .1.. .... .... .... = Don't fragment: Set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 253 Protocol: UDP (17) Header checksum: 0xed8b [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.12 Destination: 10.47.1.13 User Datagram Protocol, Src Port: 65354, Dst Port: 4789 Source Port: 65354 Destination Port: 4789 Length: 76 [Checksum: [missing]] [Checksum Status: Not present] [Stream index: 0] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Virtual eXtensible Local Area Network Flags: 0x8800, GBP Extension, VXLAN Network ID (VNI) 1... .... .... .... = GBP Extension: Defined .... .... .0.. .... = Don't Learn: False .... 1... .... .... = VXLAN Network ID (VNI): True .... .... .... 0... = Policy Applied: False .000 .000 0.00 .000 = Reserved(R): 0x0000 Group Policy ID: 0 VXLAN Network Identifier (VNI): 8190 <-- LISP L2 IID Reserved: 0 Ethernet II, Src: 52:54:00:19:93:e9 (52:54:00:19:93:e9), Dst: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00) <-- True source and destination endpoint MAC address Destination: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00) Address: 52:54:00:1e:ad:00 (52:54:00:1e:ad:00) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 52:54:00:19:93:e9 (52:54:00:19:93:e9) Address: 52:54:00:19:93:e9 (52:54:00:19:93:e9) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: ARP (0x0806) Trailer: 000000000000000000000000000000000000 Address Resolution Protocol (request) Hardware type: Ethernet (1) Protocol type: IPv4 (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (1) Sender MAC address: 52:54:00:19:93:e9 (52:54:00:19:93:e9) Sender IP address: 10.47.4.2 Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00) Target IP address: 10.47.4.3
يوضح Edge-2 عملية تضمين VXLAN ووضع علامة على طلب ARP للبث الأحادي حتى وحدة المعالجة المركزية للحصول على مزيد من المعالجة. ويمكن ملاحظة ذلك من خلال التقاط أداة FED Punject.
Edge-2#debug platform software fed switch active punt packet-capture start Punt packet capturing started. Edge-2#debug platform software fed switch active punt packet-capture stop Punt packet capturing stopped. Captured 21 packet(s) Edge-2#show platform software fed sw active punt packet-capture display-filter "arp" brief Punt packet capturing: disabled. Buffer wrapping: disabled Total captured so far: 21 packets. Capture capacity : 4096 packets ------ Punt Packet Number: 6, Timestamp: 2023/10/24 19:14:32.930 ------ interface : physical: [if-id: 0x00000000], pal: L2LISP0 [if-id: 0x00000017] metadata : cause: 109 [snoop packets], sub-cause: 1, q-no: 16, linktype: MCP_LINK_TYPE_IP [1] ether hdr : dest mac: 5254.001e.ad00, src mac: 5254.0019.93e9 ether hdr : ethertype: 0x0806 (ARP)
يتم إرسال طلب ARP إلى عملية إستطلاع ARP.
Edge-2#debug platform software infrastructure punt
*Oct 24 19:18:38.916: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 24 19:18:38.916: Punt: IP proto src 147.233.10.47, dst 4.2.0.0, from table 0, intf L2LI0, encap LISP, size 60, cause snoop packets(L3) <-- You can see the 10.47.4.2 *Oct 24 19:18:38.916: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 24 19:18:38.916: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
تحذير: تصحيح الأخطاء هذا هو الثرثرة، الاستخدام بحذر.
بما أن طلب ARP هذا يأتي من واجهة L2 LISP/نفق، فإن Edge-2 لا يتعلم مطلقا 10.47.4.2 كنقطة نهاية محلية لعيد ديناميكي في LISP
Edge-2#show platform arpsnooping client 5254.0019.93e9 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.0019.93E9: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------ 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PLATF_DAI:RECEIVED INPUT 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PLATF_DAI:RECEIVED_TUNNEL 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 PLATF_DAI:SHUNTED
الآن، يتم ضخ طلب ARP من وحدة المعالجة المركزية إلى شبكة VLAN رقم 1026، وخاصة Gi1/0/3، حيث يكون 10.47.4.3 متصلا بها.
Edge-2#show mac address-table address 5254.001e.ad00 Mac Address Table ------------------------------------------- Vlan Mac Address Type Ports ---- ----------- -------- ----- 1026 5254.001e.ad00 DYNAMIC Gi1/0/3 Total Mac Addresses for this criterion: 1
Edge-2#show platform arpsnooping client 5254.001e.ad00 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.001E.AD00: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 15:57:01.129 5254.0019.93e9 10.47.4.2 0000.0000.0000 10.47.4.3 ARP_REQUEST 1026 INJECT:BD_DPIDX_TO_FWDPLANE
تستجيب نقطة النهاية التي تملك 10.47.4.3 مع رد ARP للبث الأحادي، ويتم فرض رد ARP على وحدة المعالجة المركزية بسبب وجود IPDT. يحدث التحقق الأولي عبر EPC على الواجهة التي تواجه نقطة النهاية.
Edge-2#show monitor capture 1 buffer display-filter arp Starting the packet display ........ Press Ctrl + Shift + 6 to exit 2 88.712035 52:54:00:1e:ad:00 -> 00:00:0c:9f:f3:41 ARP 60 10.47.4.3 is at 52:54:00:1e:ad:00
بعد ذلك، تحقق من الإجراء الضاغط مع FED القصاصة
Edge-2#debug platform software fed sw active punt packet-capture start Punt packet capturing started. Edge-2#debug platform software fed sw active punt packet-capture stop Punt packet capturing stopped. Captured 22 packet(s) Edge-2#show platform software fed sw active punt packet-capture display-filter "arp" brief Punt packet capturing: disabled. Buffer wrapping: disabled Total captured so far: 22 packets. Capture capacity : 4096 packets ------ Punt Packet Number: 6, Timestamp: 2023/10/24 20:32:35.634 ------ interface : physical: [if-id: 0x00000000], pal: L2LISP0 [if-id: 0x00000017] metadata : cause: 109 [snoop packets], sub-cause: 1, q-no: 16, linktype: MCP_LINK_TYPE_IP [1] <-- Punted for Snoop Packets to CPU queue 16 ether hdr : dest mac: 5254.001e.ad00, src mac: 5254.0019.93e9 ether hdr : ethertype: 0x0806 (ARP)
بعد ذلك، يتم تمرير رد ARP إلى إستطلاع ARP وتتبع الجهاز
Edge-2#debug platform software infrastructure punt
*Oct 24 19:18:39.101: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 24 19:18:39.101: Punt: IP proto src 173.0.10.47, dst 4.3.82.84, from table 0, intf Gi1/0/3, encap ARPA, size 60, cause snoop packets(L3) <-- 10.47.4.3 is obscured *Oct 24 19:18:39.101: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 24 19:18:39.101: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
Edge-2#debug platform fhs Edge-2#debug platform fhs all ARP packet received from ARP snooper(Gi1/0/3 10.47.4.3 (5254.001e.ad00) VLAN:10
تحذير: هذه الأخطاء عبارة عن دردشة، أستخدم بحذر.
Edge-2#debug device-tracking
*Oct 24 20:42:22.554: SISF[CLA]: Interest on target vlan 1026 *Oct 24 20:42:22.554: SISF[CLA]: feature Device-tracking *Oct 24 20:42:22.554: SISF[CLA]: feature Address Resolution Relay
*Oct 24 20:42:22.555: SISF[SWI]: Gi1/0/3 vlan 1026 Feature_0 Device-tracking priority 128 *Oct 24 20:42:22.555: SISF[SWI]: Gi1/0/3 vlan 1026 Feature_1 Address Resolution Relay priority 81 *Oct 24 20:42:22.555: SISF[PRS]: ARP-REPLY target set to 10.47.4.2 *Oct 24 20:42:22.556: SISF[SWI]: Gi1/0/3 vlan 1026 Feature Device-tracking rc: OK *Oct 24 20:42:22.556: SISF[ARR]: Gi1/0/3 vlan 1026 Receive a msg in AR *Oct 24 20:42:22.557: SISF[ARR]: Gi1/0/3 vlan 1026 Not ARP Request or NS, return OK *Oct 24 20:42:22.557: SISF[SWI]: Gi1/0/3 vlan 1026 Feature Address Resolution Relay rc: OK *Oct 24 20:42:22.557: SISF[SWI]: Gi1/0/3 vlan 1026 Features execution OK
بما أن رد ARP يشير بالفعل إلى غاية حقيقية {upper}mac address (ليس مثل موضع مؤقت كما يظهر على Edge-1) يمكن أن يطلق Edge-2 طلب خريطة LISP لحل اقتران RLOC-MAC.
Edge-2#debug lisp control-plane all
Edge-2#debug l2lisp all
*Oct 24 20:47:34.400: LISP[REMT ]-0 IID 8190: Schedule processing of Map-Requests from 'remote EID prefix' in IPv4. *Oct 24 20:47:34.401: LISP[REMT ]-0: Map Request: Sending request for IID 8190 EID 5254.0019.93e9/48, requester 'remote EID prefix'. *Oct 24 20:47:35.166: LISP[TRNSP]-0: Processing received Map-Reply(2) message on GigabitEthernet1/0/1 from 10.47.1.11:4342 to 10.47.1.13:4342. *Oct 24 20:47:35.166: LISP[REMT ]-0: Received Map-Reply with nonce 0x5879579E-0xCAFC0AA5, 1 records. *Oct 24 20:47:35.166: LISP[REMT ]-0: Processing Map-Reply mapping record for IID 8190 MAC 5254.0019.93e9/48 LCAF 2, ttl 1440, action none, not authoritative, 1 locator. *Oct 24 20:47:35.166: LISP[REMT ]-0: 10.47.1.12 pri/wei/dID/mID/met/si_type/si_id/si_flg/afn_id=10/10/0/0/4294967295/none/0/UNSPEC/UNSPEC lpR.
أستخدم الأمر show lisp instance-id <L2 IID> ethernet map-cache <destination mac address> للتحقق من أي RLOC سيتم إرسال رد ARP هذا إليه مع تضمين VXLAN
Edge-2#show lisp instance-id 8190 ethernet map-cache 5254.0019.93e9 LISP MAC Mapping Cache for LISP 0 EID-table Vlan 1026 (IID 8190), 1 entries 5254.0019.93e9/48, uptime: 00:03:45, expires: 23:56:15, via map-reply, complete Sources: map-reply State: complete, last modified: 00:03:45, map-source: 10.47.1.12 Active, Packets out: 6(0 bytes), counters are not accurate (~ 00:00:59 ago) Encapsulating dynamic-EID traffic Locator Uptime State Pri/Wgt Encap-IID 10.47.1.12 00:03:45 up 10/10 - Last up-down state change: 00:03:45, state change count: 1 Last route reachability change: 2w0d, state change count: 1 Last priority / weight change: never/never RLOC-probing loc-status algorithm: Last RLOC-probe sent: 00:03:45 (rtt 861ms)
بعد تحليل LISP، يمكن إدخال الرد على بروتوكول تحليل العناوين (ARP) من وحدة المعالجة المركزية (CPU) في خط الأساس 10.47.1.12 RLOC
Edge-2#show ip cef 10.47.1.12 10.47.1.12/32 nexthop 10.47.1.2 GigabitEthernet1/0/2 nexthop 10.47.1.6 GigabitEthernet1/0/1
يمكن ملاحظة التدفق بالكامل على وحدة المعالجة المركزية من Edge-2 عبر EPC، والفرق بين الرد على ARP وطلب ARP هو عدم وجود دقة LISP AR في هذا التدفق.
Edge-2#show monitor capture 1 buffer display-filter "arp.src.proto_ipv4==10.47.4.3 or lisp" Starting the packet display ........ Press Ctrl + Shift + 6 to exit 62 9.355185 52:54:00:1e:ad:00 -> 52:54:00:19:93:e9 ARP 60 10.47.4.3 is at 52:54:00:1e:ad:00 <-- ARP Reply punted up to the CPU 63 9.355486 0.0.0.0 -> 0.0.0.0 LISP 176 Encapsulated Map-Request for [8190] 52:54:00:19:93:e9/48 <-- LISP Map-Request to resolve RLOC-MAC association 88 12.058412 10.47.1.10 -> 10.47.1.13 LISP 96 Map-Reply for [8190] 52:54:00:19:93:e9/48 <-- LISP Map-Reply providing the RLOC-MAC association 90 12.072455 52:54:00:1e:ad:00 -> 52:54:00:19:93:e9 ARP 110 10.47.4.3 is at 52:54:00:1e:ad:00 <-- VXLAN Encapsulated ARP Reply that is injected by the CPU
تلميح: لا يلتقط FED Punject Capture ردود ARP التي تم حقنها، أستخدم تتبع Fed Injbose
أنت يستطيع استعملت الأمر show platform arpsnooping client <source mac address>أن يرى الإجراء اتخذ على Edge-2 فيما يتعلق ب ARP رد
Edge-2#show platform arpsnooping client 5254.001e.ad00 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.001E.AD00: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
2023/10/24 20:47:38.151 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED INPUT 2023/10/24 20:47:38.151 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:TO_ARPSND 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PSISF_PRE:PSP_INJNEUTRAL 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 20:47:38.152 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:BD_DPIDX_TO_FWDPLANE
يستلم Edge-1 ال VXLAN يغلف ARP رد، POP VXLAN رأس خارج ويرسل ال ARP رد إلى المعالجة المركزية ل كثير معالجة.
Edge-1#debug platform software infrastructure punt
*Oct 24 21:42:11.303: PUNT RX: mcprp_process_receive_packet: pak->vlan_id: 1026 *Oct 24 21:42:11.303: Punt: IP proto src 173.0.10.47, dst 4.3.82.84, from table 0, intf L2LI0, encap LISP, size 60, cause snoop packets(L3) <-- Can see 10.47.4.3 IP address that has been obscured *Oct 24 21:42:11.303: punt cause:snoop packets invoking reg_invoke_mcprp_punt_feature_msg *Oct 24 21:42:11.303: punt cause:snoop packets MCPRP_PUNT_PAK_PROC_OK_DONE
يمكنك إستخدام الأمر show platform arpsnooping client <source mac address> للحصول على معلومات إضافية حول كيفية معالجة رد ARP على Edge-1
Edge-1#show platform arpsnooping client 5254.001e.ad00 PLAT_DAI : Platform DAI shim FWDPLANE : Dataplane forwarding BRIDGE : Packet to be bridged ARPSN : Arp Snooping Packet Trace for client MAC 5254.001E.AD00: Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action ----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED INPUT 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:RECEIVED_TUNNEL 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 PLATF_DAI:SHUNTED 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:INJ_VLAN_IFINPUT_TO_BDI 2023/10/24 20:40:33.741 5254.001e.ad00 10.47.4.3 5254.0019.93e9 10.47.4.2 ARP_REPLY 1026 INJECT:BD_DPIDX_TO_FWDPLANE
Edge-1 يأخذ ال ARP جواب ويرسل ال ARP رد إلى VLAN 1026، إلى الميناء حيث نقطة النهاية 10.47.4.2 يعيش
Edge-1#show mac address-table address 5254.0019.93e9 Mac Address Table ------------------------------------------- Vlan Mac Address Type Ports ---- ----------- -------- ----- 1026 5254.0019.93e9 DYNAMIC Gi1/0/3 Total Mac Addresses for this criterion: 1
مع غمر L2، يمكن أن يحدث أيضا تحليل ARP حيث تنضم جميع عقد حافة البنية في البنية بالإضافة إلى حدود نقل L2/IP الموجهة التي تدعم البث المتعدد إلى مجموعة أساسية مشتركة مشتركة. كل مرة تصل فيها حزمة/إطار مؤهل للتدفق إلى عقدة Edge، يتم تضمين شبكة VXLAN مع عنوان IP للوجهة لمجموعة البث المتعدد الأساسية. يمكن تطبيق غمر L2 على دقة ARP في سيناريوهات معينة:
بمجرد تكوين البث المتعدد الأساسي وتمكين تدفق arp-nd، يؤدي هذا إلى تغيير كيفية معالجة طلب ARP، والذي كان يستخدم في الأصل الدقة المستندة إلى LISP/ISF. ما إن يفيض arp-nd يكون شكلت تحت ال L2 LISP مثال، هذا يعجز ال LISP-ARP-RELAY-VLAN IPDT سياسة ل ال VLAN، ولا يستعمل.
Edge-1#show device-tracking policies vlan 1026 Target Type Policy Feature Target range vlan 1026 VLAN DT-PROGRAMMATIC Device-tracking vlan all vlan 1026 VLAN LISP-DT-GLEAN-VLAN-MULTI-IP Device-tracking vlan all
بعد تلقي طلب ARP من العميل في فيضان L2 الممكن VLAN مع طوفان arp-nd يشكل، لم يعد يتم معالجته بواسطة التطفل على ARP. يتم فرض حظر على طلب ARP حتى وحدة المعالجة المركزية لأغراض تعلم IPDT ولكن ليس لإعادة التوجيه.
لا يقوم متصفح ARP بمعالجة طلب ARP، والذي يمكن رؤيته باستخدام الأمر show platform arpsnooping client <MAC address>
Edge-1#show platform arpsnooping client 5254.0019.93e9
PLAT_DAI : Platform DAI shim
FWDPLANE : Dataplane forwarding
BRIDGE : Packet to be bridged
ARPSN : Arp Snooping
Packet Trace for client MAC 5254.0019.93E9:
Timestamp Sender Mac Sender IP Target Mac Target IP Opcode VLAN Handler:Action
----------------------- --------------- ------------- ----------------- -------------- ------------ ------- ------------------------------
Filtered entries counters:
ARPSN_FILTER_SVI: 0
لا يقوم Edge-1 بإنشاء إدخال RMT IPDT لنقطة النهاية 10.47.4.3 كما هو موضح في الإخراج
Edge-1#show monitor capture 1 buffer display-filter arp brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit 1 0.000000 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2
Edge-1#show device-tracking database address 10.47.4.3 Codes: L - Local, S - Static, ND - Neighbor Discovery, ARP - Address Resolution Protocol, DH4 - IPv4 DHCP, DH6 - IPv6 DHCP, PKT - Other Packet, API - API created Preflevel flags (prlvl): 0001:MAC and LLA match 0002:Orig trunk 0004:Orig access 0008:Orig trusted trunk 0010:Orig trusted access 0020:DHCP assigned 0040:Cga authenticated 0080:Cert authenticated 0100:Statically assigned Network Layer Address Link Layer Address Interface vlan prlvl age state Time left
الآن، ال ARP طلب VXLAN يغلف داخل الإذاعة تحت مجموعة multicast. Edge-1 له مسار مع Loopback0 كمصدر، والمجموعة بث المجموعة تحتها مجموعة.
Edge-1#show run int lo0 Building configuration... Current configuration : 135 bytes ! interface Loopback0 ip address 10.47.1.12 255.255.255.255 no ip redirects ip pim sparse-mode <-- PIM must be enabled ip router isis clns mtu 1400 end
Edge-1#show ip mroute 239.0.17.2 IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, G - Received BGP C-Mroute, g - Sent BGP C-Mroute, N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, Q - Received BGP S-A Route, q - Sent BGP S-A Route, V - RD & Vector, v - Vector, p - PIM Joins on route, x - VxLAN group, c - PFP-SA cache created entry, * - determined by Assert, # - iif-starg configured on rpf intf, e - encap-helper tunnel flag, l - LISP decap ref count contributor Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join t - LISP transit group Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.0.17.2), 5w1d/00:02:05, RP 10.47.1.14, flags: SJC Incoming interface: GigabitEthernet1/0/2, RPF nbr 10.47.1.4 Outgoing interface list: L2LISP0.8190, Forward/Sparse-Dense, 01:56:41/00:00:18, flags: L2LISP0.8192, Forward/Sparse-Dense, 2w2d/00:00:58, flags: L2LISP0.8188, Forward/Sparse-Dense, 5w1d/00:01:58, flags: (10.47.1.12, 239.0.17.2), 00:02:53/00:00:06, flags: PFT <-- Lo0 interface of Edge-1 Incoming interface: Null0, RPF nbr 0.0.0.0, <-- Incoming interface Null0 is expected Outgoing interface list: GigabitEthernet1/0/2, Forward/Sparse, 00:04:40/00:02:45, flags: <-- Outgoing interface Gig1/0/2 faces the fabric underlay
وفي واقع الأمر، يتغازل بروتوكول تحليل العناوين (ARP) مع IPDT/ISF بدلا من إغراق نفسه. فيض L2 يفيض بالفعل عمليات البث، ولكن الخدعة هي تعطيل سياسة LISP AR من تعقب الأجهزة، وقد تم الآن إطلاق ملكية ARP ويمكن إغراقها تماما مثل أي بث آخر.
للتحقق من برمجة الأجهزة للتدفق على المستوى الثاني، أستخدم الأمر show platform software dpidb l2lisp <L2 LISP IID>
Edge-1#show platform software dpidb l2lisp 8190 Instance Id:8190, dpidx:25, vlan:1026, Parent Interface:L2LISP0(if_id:23) <-- dpidx value used in the next command
تأخذ قيمة dpidx من الأمر السابق وتستعمل في الأمر show platform software fed switch active ifm if-id <dpidx value>
Edge-1#show platform software fed switch active ifm if-id 25 Interface IF_ID : 0x0000000000000019 Interface Name : L2LISP0.8190 Interface Block Pointer : 0x7f65ec85ba78 Interface Block State : READY Interface State : Enabled Interface Status : ADD, UPD Interface Ref-Cnt : 2 Interface Type : L2_LISP Created Time : 2023/09/19 17:57:32.046 Last Modified Time : 2023/10/25 17:59:09.265 Current Time : 2023/10/25 20:15:44.624 Is top interface : FALSE Asic_num : 0 Switch_num : 0 AAL port Handle : 7a00003a Parent interface id : 17 Multicast Tunnel IP : 239.0.17.2 Mcast Tunnel Handle : 0x7f65ed356918 L2 Multicast Tunnel IP : 0.0.0.0 L2 Multicast Vlan Id : 0 L2 Multicast Tunnel Hdl : NULL Vlan Id : 1026 Instance Id : 8190 Dest Port : 4789 SGT : Enable Underlay VRF (V4) : 0 Underlay VRF (V6) : 0 Flood Access-tunnel : Disable Flood unknown ucast : Enable Broadcast : Enable Multicast Flood : Enable L2 Multicast Flood : Disable Host Activity report: Enabled <snip>
يمكنك إستخدام EPC على Gi1/0/2 في إتجاه المخرج، لأن طلب ARP هذا يتم إعادة توجيهه إلى الداخل والخارج دون الحاجة إلى إدخال وحدة المعالجة المركزية، يمكنك الثقة في لقطات EPC في قرار الخروج هذه المرة.
Edge-1#monitor capture 1 start Started capture point : 1 Edge-1#monitor capture 1 stop Capture statistics collected at software: Capture duration - 22 seconds Packets received - 5 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1
Edge-1#show monitor capture 1 buffer brief Starting the packet display ........ Press Ctrl + Shift + 6 to exit 1 0.000000 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 110 Who has 10.47.4.3? Tell 10.47.4.2 <-- Size 110 because VXLAN, UDP, and other headers
أنت يستطيع ألقيت نظرة أقرب إلى ال VXLAN يغلف ARP طلب
Edge-1#show monitor capture 1 buffer display-filter frame.number==1 detailed Starting the packet display ........ Press Ctrl + Shift + 6 to exit Frame 1: 110 bytes on wire (880 bits), 110 bytes captured (880 bits) on interface /tmp/epc_ws/wif_to_ts_pipe, id 0 Interface id: 0 (/tmp/epc_ws/wif_to_ts_pipe) Interface name: /tmp/epc_ws/wif_to_ts_pipe Encapsulation type: Ethernet (1) Arrival Time: Oct 25, 2023 20:44:36.578645000 UTC [Time shift for this packet: 0.000000000 seconds] Epoch Time: 1698266676.578645000 seconds [Time delta from previous captured frame: 0.000000000 seconds] [Time delta from previous displayed frame: 0.000000000 seconds] [Time since reference or first frame: 0.000000000 seconds] Frame Number: 1 Frame Length: 110 bytes (880 bits) Capture Length: 110 bytes (880 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ethertype:ip:udp:vxlan:eth:ethertype:arp] Ethernet II, Src: 00:00:00:00:00:00 (00:00:00:00:00:00), Dst: 00:00:00:00:00:00 (00:00:00:00:00:00) <-- Ignore the all 0s MAC, not accurate Destination: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Source: 00:00:00:00:00:00 (00:00:00:00:00:00) Address: 00:00:00:00:00:00 (00:00:00:00:00:00) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: IPv4 (0x0800) Internet Protocol Version 4, Src: 10.47.1.12, Dst: 239.0.17.2 <-- Source is Edge-1 RLOC, Destination is the broadcast underlay group 0100 .... = Version: 4 .... 0101 = Header Length: 20 bytes (5) Differentiated Services Field: 0x00 (DSCP: CS0, ECN: Not-ECT) 0000 00.. = Differentiated Services Codepoint: Default (0) .... ..00 = Explicit Congestion Notification: Not ECN-Capable Transport (0) Total Length: 96 Identification: 0x8dab (36267) Flags: 0x4000, Don't fragment 0... .... .... .... = Reserved bit: Not set .1.. .... .... .... = Don't fragment: Set ..0. .... .... .... = More fragments: Not set Fragment offset: 0 Time to live: 255 Protocol: UDP (17) Header checksum: 0xe2a3 [validation disabled] [Header checksum status: Unverified] Source: 10.47.1.12 Destination: 239.0.17.2 User Datagram Protocol, Src Port: 65280, Dst Port: 4789 Source Port: 65280 Destination Port: 4789 Length: 76 [Checksum: [missing]] [Checksum Status: Not present] [Stream index: 0] [Timestamps] [Time since first frame: 0.000000000 seconds] [Time since previous frame: 0.000000000 seconds] Virtual eXtensible Local Area Network Flags: 0x8800, GBP Extension, VXLAN Network ID (VNI) 1... .... .... .... = GBP Extension: Defined .... .... .0.. .... = Don't Learn: False .... 1... .... .... = VXLAN Network ID (VNI): True .... .... .... 0... = Policy Applied: False .000 .000 0.00 .000 = Reserved(R): 0x0000 Group Policy ID: 0 VXLAN Network Identifier (VNI): 8190 <-- L2 LISP IID Reserved: 0 Ethernet II, Src: 52:54:00:19:93:e9 (52:54:00:19:93:e9), Dst: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) <-- SMAC and DMAC of the ARP Request Destination: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) Address: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast) Source: 52:54:00:19:93:e9 (52:54:00:19:93:e9) Address: 52:54:00:19:93:e9 (52:54:00:19:93:e9) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) Type: ARP (0x0806) Trailer: 000000000000000000000000000000000000 Address Resolution Protocol (request) Hardware type: Ethernet (1) Protocol type: IPv4 (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (1) Sender MAC address: 52:54:00:19:93:e9 (52:54:00:19:93:e9) Sender IP address: 10.47.4.2 Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00) Target IP address: 10.47.4.3
ينضم Edge-2 إلى مجموعة البث الأساسية، 239.0.17.2 ويمتلك S،G ل Edge-1، ويستلم حزمة البث المتعدد المغلف VXLAN على Gig1/0/1 و LISP0.8190 الموجودة في قائمة الواجهة الصادرة. تستخدم الإصدارات الأقدم من الرمز مثل 17.3 أو الأقدم واجهة نفق بدلا من واجهة LISP0 الفرعية.
Edge-2#show ip mroute 239.0.17.2 IP Multicast Routing Table Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected, L - Local, P - Pruned, R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet, X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement, U - URD, I - Received Source Specific Host Report, Z - Multicast Tunnel, z - MDT-data group sender, Y - Joined MDT-data group, y - Sending to MDT-data group, G - Received BGP C-Mroute, g - Sent BGP C-Mroute, N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed, Q - Received BGP S-A Route, q - Sent BGP S-A Route, V - RD & Vector, v - Vector, p - PIM Joins on route, x - VxLAN group, c - PFP-SA cache created entry, * - determined by Assert, # - iif-starg configured on rpf intf, e - encap-helper tunnel flag, l - LISP decap ref count contributor Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join t - LISP transit group Timers: Uptime/Expires Interface state: Interface, Next-Hop or VCD, State/Mode (*, 239.0.17.2), 5w1d/stopped, RP 10.47.1.14, flags: SJC Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.6 Outgoing interface list: L2LISP0.8190, Forward/Sparse-Dense, 02:28:57/00:01:02, flags: L2LISP0.8192, Forward/Sparse-Dense, 2w2d/00:00:32, flags: L2LISP0.8188, Forward/Sparse-Dense, 5w1d/00:02:54, flags: (10.47.1.12, 239.0.17.2), 00:00:03/00:02:56, flags: JT Incoming interface: GigabitEthernet1/0/1, RPF nbr 10.47.1.6 <-- Interface that faces the fabric underlay and the RPF interface towards 10.47.1.12 Outgoing interface list: L2LISP0.8188, Forward/Sparse-Dense, 00:00:03/00:02:56, flags: L2LISP0.8192, Forward/Sparse-Dense, 00:00:03/00:02:56, flags: L2LISP0.8190, Forward/Sparse-Dense, 00:00:03/00:02:56, flags:
يستلم Edge-2 ال VXLAN يغلف ربط، ينفصل ال VXLAN رأس ويفيض الربط داخل VLAN 1026، أي يستطيع كنت رأيت في EPC على القارن قادم as well as القارن يواجه النهاية.
Edge-2#monitor capture 1 interface gig1/0/1 in match any Edge-2#monitor capture 1 int g1/0/3 out Edge-2#monitor capture 1 start Started capture point : 1 Edge-2#monitor capture 1 stop Capture statistics collected at software: Capture duration - 22 seconds Packets received - 43 Packets dropped - 0 Packets oversized - 0 Number of Bytes dropped at asic not collected Capture buffer will exists till exported or cleared Stopped capture point : 1 Edge-2#show monitor capture 1 buffer display-filter arp Starting the packet display ........ Press Ctrl + Shift + 6 to exit 10 6.230153 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 110 Who has 10.47.4.3? Tell 10.47.4.2 <-- Size 110 is the VXLAN encapsulated ARP Request 11 6.404781 52:54:00:19:93:e9 -> ff:ff:ff:ff:ff:ff ARP 60 Who has 10.47.4.3? Tell 10.47.4.2 <-- Size 60 is the original ARP Request
تكون ردود ARP دائما تقريبا أحادية البث، ما لم تكن ARP مجانية. بالنسبة لردود ARP للبث الأحادي، لا يوجد تمييز بين سير العمل لمسار Unicast استنادا إلى LISP/ISF أو مسار التفيض المستند إلى ARP-ND للتدفق، يستخدم كلاهما نفس مسار البث الأحادي الذي يتضمن اكتشاف ISF/IPDT. يمكنك الاستفادة من قسم التحقق من رد ARP الخاص بمسار البث الأحادي لاستكشاف الأخطاء وإصلاحها.
المراجعة | تاريخ النشر | التعليقات |
---|---|---|
2.0 |
26-Oct-2023 |
الإصدار الأولي |
1.0 |
12-Aug-2020 |
الإصدار الأولي |