Resolved Caveats – Cisco IOS XE Bengaluru 17.6.8
There are no resolved caveats in this release.
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This chapter describes open and resolved severity 1 and 2 caveats and select severity 3 caveats:
The “Open Caveats” sections list open caveats that apply to the current release and may apply to previous releases. A caveat that is open for a prior release and is still unresolved applies to all future releases until it is resolved.
The “Resolved Caveats” sections list caveats resolved in a specific release, but open in previous releases.
The bug IDs are sorted alphanumerically.
Note |
The Caveats section includes the bug ID and a short description of the bug. For details on the symptoms, conditions, and workaround for a specific caveat you must use the Bug Search Tool. |
There are no resolved caveats in this release.
There are no open caveats in this release.
Identifier |
Headline |
---|---|
After losing primary master, T-BC stuck in HOLDOVER state though secondary master is reachable. |
|
CSCwh85621 |
RSP3 : \"sh pla ha cef ip/ipv6\" command is displaying partial output for POCH interface |
There are no open caveats in this release.
Identifier |
Headline |
---|---|
Cisco IOS XE Software Web UI Privilege Escalation Vulnerability |
There are no open caveats in this release.
Identifier |
Headline |
---|---|
T3: DCR: cem id not displayed correctly under "sh recovered-clock" |
|
rs232 ASYNC PW service with full scale seeing packet and byte drops intermittently |
|
DS3_ADMIN_DOWN gets cleared after IM OIR |
|
VIN P2/0, VOUT P2/2, VIN P4/0 & VOUT P4/2 alarms upon SSO |
|
Ony in 3GMS OC3 port with network loop Bert pattern is not syncing |
|
CEM traffic flow is dropped in one direction due to DEI bit set from 4202 |
|
After SSO: False Alarm on CNAAP |
|
with x.21 configured observing underruns in cem counters |
|
PAIS alarm get reported after IM OIR. |
|
Controllers are down due to LP-LOP alarm After CE reboots |
|
cem interface counters momentarily report error when x21 xconnect is cleared and re-established |
|
Power sensor threshold warning alarms in EPNM |
|
With CPG, STS1e configuration is giving %ERROR: Standby doesn't support this command |
|
All readings for Power supply unit reflect as zero though the unit is functional |
|
In IMA32D/IMA8D card, sometimes change in E1 controller config(after ctrlr flap)results in IM reboot |
|
with traffic ON, when speed lowered on ASYNC port, SYNC port CEM traffic gets impacted |
|
"show version" does not display details of T1/E1 interfaces for 8D and 32D IMs |
|
frequent reloads of IM due to high temp- FAN speed mismatch |
There are no resolved caveats in this release.
Identifier |
Headline |
---|---|
MPLS L3VPN PE not able to connect remote CE |
|
Fan running at high speed and creating noise(Fan PID A903-FAN-H ) |
|
Standard loopback is not working when applied on both the ends on a back to back link |
|
HW Mcirobfd is flapping with Interop tests on RSP3 |
Identifier |
Headline |
---|---|
Crash seen TILFA Flex algo Any cast address during config replace |
|
Remote LInk Failure notification is disabled when configuring through YANG |
|
Traceback seen when default made on all core intfs. |
|
Running configuration syn to the NETCONF running data store takingmor time |
|
VRF is not deleted after replacing default config |
|
Connect CLI used for local connect needs to take care of monitor session also |
|
If show controller cli is executed immediately after l2vpn xconnect config w/o exit, leads to iosd |
|
micro bfd: registry call to get encap type of a service instance |
Identifier |
Headline |
---|---|
Continuous assertion and clear of LAIS on protect channel causing IPC failure |
|
APS - K2 byte not reflecting proper value during LRDI and LAIS conditions. |
|
Synchronization Status Messaging (S1) Processing and Generation issue |
|
APS 1+1 Uni - Tx K2 to reflect Rx K1 channel number |
|
A900-IMASER14A/S: when configurations are pasted in a specific order, line config is missing |
|
After router reload E1 framing gets changed to unframed in SDH VC12 mode with channe-group config |
|
EVPN statd resource leak after protocol flaps |
|
17.9 : APS-ACR config/unconfig results in traffic drop |
|
FPD: Failure to downgrade the firmware of card 0/0 |
|
Need support for dual options in CLI for setting clock rate for x21 |
|
Change in SD-BER threshold value to 10e-9 causes SD alarm assertion |
|
RSP3: MPLS pseudowirte - Incorrect label stack pushed to packet |
|
ToD state is down with gnss module |
|
Alarm assertion/clearing not happening for port x+1 when complete sonet config for port x is removed |
|
Memory leak on ptpd_uea process |
|
rs485 with half-duplex configuration when reloaded, it gets into default full-duplex mode |
|
RSP2 crashes when entering "ip prefix" list |
Identifier |
Headline |
---|---|
RSP2 UDP pseudowire stuck in Activating |
|
Invalid BGP update when add-paths negotiated only for label (SAFI 4) and not unicast (SAFI1) |
|
RSP3: MSPW VC down points to Error Local access circuit is not ready for label advertise |
|
A BGP speaker may advertise a next-hop set to self when advertising an eBGP route to an iBGP peer. |
Identifier |
Headline |
---|---|
mcast data traffic is getting dropped over vpls |
|
RSP-3C - uea_mgr crash seen with uea_brcm_update_hw_stats |
|
Fan running at high speed and creating noise (Fan PID A903-FAN) - SW version 17.03.04 |
|
Ony in 3GMS OC3 port with network loop Bert pattern is not syncing |
|
Unexpected reload due to MLDPv6 |
|
IOMD Crash and IMA32D/IMA8D card reboot when change E1 config during E1 interface flapping |
|
Performance issue on router platform |
Identifier |
Headline |
---|---|
Traceback and IDB leak noticed when a RSP3 setup performs a switchover |
|
Traceback seen when default made on all core intfs |
|
Running configuration syn to the NETCONF running data store takes more time |
|
Remote Link Failure notification is disabled when configuring through YANG |
Identifier |
Headline |
---|---|
Convergence is > 50ms during RSP SSO and Core flap with 2 pot-channel interface. |
|
ASR900 may experience an unexpected reset when configuring or using interface BDI >= 4097 |
|
Multihop BFD transit packets getting droppedn on ASR920 after upgrade to 17.3.3 |
|
MLPPP: Traffic Drop seen after the addition of 2 or more member links |
|
ASR903: Tengig interface remained DOWN after ISSU upgrade from 17.04.01 to 17.7.1 throttle |
|
Problem with CISCO-ENTITY-SENSOR-MIB SNMP on ASR903 router |
Identifier |
Headline |
---|---|
G.8032: Ring brief output doesnt display the Block port flag in Idle state |
|
RSP3/ASR920/RSP2:node crashed @ l2rib_obj_peer_tbl_cmd_print |
Identifier |
Headline |
---|---|
FPD: Failure to downgrade the firmware of card 0/0 |
|
TCAM corruption happening at bank boundary when one of the bank is full. |
There are no open caveats in this release.
Identifier |
Headline |
---|---|
RSP3: Implement show command to display voq that failed during delete voq |
|
The router will crash when zeroised RSA key is regenerated |
|
Raw-socket config-event use all the iomem when L1 is down |
|
MAC table inconsistency due to parity error. |
|
When IOT IM is inserted in slot 4, gigEth traffic on slot 14 fails |
|
iMSG serial interfaces bitrate/sec data is displayed incorrectly in show command output |
|
Interfaces are showing up in SNMP polling while associated Hardware Does not Exists on System |
|
STS1e card protection - Recovered clock status is shown as NA for work and protect ports |
|
Need to support few line level CLIs with "no" even without any cable attached. |
|
Raw-socket config-event use all the iomem if connected device L1 signals are down |
|
rs232 service on port8 gives SLIP errors when databits is set on other ports |
|
RSP3: QOSMGR-4-QUEUE_ExCEEDING_HW: VOQs exceeded hardware limit |
|
Router crashed with IP SLA configuration which is not supported. |
|
F2B chassis: show env does not display the fan speed. |
Identifier |
Headline |
---|---|
RSP failover on router showing several seconds of outage for L2VPN services. |
Identifier |
Headline |
---|---|
TCAM corruption happening at bank boundary when one of the bank is full. |
Identifier |
Headline |
---|---|
FRR is not calculating backup route due to "primary_update_complete_pending:" flag set to 1. |
|
MVPN Profile 14: Data MDT traffic not flowing with 2 paths when OSPF cost configured on 1 path. |
|
RSP3 ICCP stuck on the CONNECTING state after RSP SO on Active PoA. |
Caveat ID Number |
Description |
---|---|
With 30 clock ports there are PTP flaps and deselection of current master. |
|
Active RP HW goes down during an IO FPGA Upgrade and Standby started booting in Loop. |
|
LLC frames are getting looped back due to autonomic networking. |
|
In CT3 E1 and CT3 mode, the loopback local is not getting applied, and controller goes down. |
|
IMs on slots 13, 14, and 15 out of service on ASR-907 chassis |
|
Egress QoS classification issues with Service instance 2 configuration on CE facing interfaces |
|
DWDM SFPs threshold Value set to 0.0 dbm for RX/TX and -0.0 C for temperature. |
|
Ping issue with MTU greater than 1508. |
|
EIGRP flapping on framing SDH Serial interface. |
|
DHCP packets are not forwarded from Client to Server when DHCP snooping is enabled globally. |
|
IP MTU incorrectly programmed in ASIC after removing/reconfiguring the IP address. |
|
HQoS on egress TenGig interface is not working properly. |
|
APS ACR scale: traffic goes down after router reload egress counters are 0. |
|
Incorrect timestamping: registry to use/update receive timestamp for RSP3 platform. |
|
RSP3: BDI routing frames corrupted on deletion and recreation of EFP. |
|
IMA1Z8S-CX-MS Protection switching on LOS condition disrupts service for greater than 200 msec. |
|
DS3 card protection - iosd crash upon no mode T3. |
|
APS:ACR traffic fails after ISSU from 16.12 to 17.3 |
|
PTP Source port IDs are different in Sync and Announce, Delay-resp packets from the master. |
|
Drop tunneled packets for protocols for which tunnel is configured locally. |
Caveat ID Number |
Description |
---|---|
New Bridge-Domain are not added dynamically to POCH when TEFP-encap from-bd is configured. |
Caveat ID Number |
Description |
---|---|
The router goes down when zeroised RSA key is regenerated |
|
TCAM corruption happening at bank boundary when one of the bank is full. |
|
Raw-socket config-event uses all the iomem if connected device L1 signals are down |
Caveat ID Number |
Description |
---|---|
IP IW XC Scenario - From ethernet to tdm side, IGP label is NOT pushed |
|
[SVSP-497]-Op state and Ad state showing NA for all slot with Bandwidth command |
|
The pubd process crashed during ISSU from 17.6.1 to 17.3_throttle |
Caveat ID Number |
Description |
---|---|
In T3 controller-CT3 E1 and CT3 mode the loopback local is not getting applied, controller stays down |
|
TAP:Hard IM OIR and router reload causing OBJ_DOWNLOAD_FAIL when multiple modes are enabled |
Cisco Bug Search Tool (BST), the online successor to Bug Toolkit, is designed to improve effectiveness in network risk management and device troubleshooting. You can search for bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. For more details on the tool, see the help page located at http://www.cisco.com/web/applicat/cbsshelp/help.html