De documentatie van dit product is waar mogelijk geschreven met inclusief taalgebruik. Inclusief taalgebruik wordt in deze documentatie gedefinieerd als taal die geen discriminatie op basis van leeftijd, handicap, gender, etniciteit, seksuele oriëntatie, sociaaleconomische status of combinaties hiervan weerspiegelt. In deze documentatie kunnen uitzonderingen voorkomen vanwege bewoordingen die in de gebruikersinterfaces van de productsoftware zijn gecodeerd, die op het taalgebruik in de RFP-documentatie zijn gebaseerd of die worden gebruikt in een product van een externe partij waarnaar wordt verwezen. Lees meer over hoe Cisco gebruikmaakt van inclusief taalgebruik.
Cisco heeft dit document vertaald via een combinatie van machine- en menselijke technologie om onze gebruikers wereldwijd ondersteuningscontent te bieden in hun eigen taal. Houd er rekening mee dat zelfs de beste machinevertaling niet net zo nauwkeurig is als die van een professionele vertaler. Cisco Systems, Inc. is niet aansprakelijk voor de nauwkeurigheid van deze vertalingen en raadt aan altijd het oorspronkelijke Engelstalige document (link) te raadplegen.
In dit document wordt de upgradeprocedure van versie 16.6.1 naar 16.6.2 beschreven.
Cisco raadt u aan kennis te hebben van TFTP en FTP.
De informatie in dit document is gebaseerd op de volgende software- en hardware-versies:
In dit voorbeeld is de huidige afbeelding cat9k_iosxe.16.06.01.SPA.bin en is de doelafbeelding cat9k_iosxe.16.06.02.SPA.bin. Deze procedure werkt ook als u een C9407R chassis in plaats van een C9410R chassis hebt.
Opmerking: upgrade geen dubbele supervisors van Cisco IOS® XE Everest 16.6.1 naar 16.6.2 tegelijk. Plaats één supervisor tegelijkertijd terwijl u van 16.6.1 aan 16.6.2 verbetert.
De informatie in dit document is gebaseerd op de apparaten in een specifieke laboratoriumomgeving. Alle apparaten die in dit document worden beschreven, hadden een opgeschoonde (standaard)configuratie. Als uw netwerk live is, moet u zorgen dat u de potentiële impact van elke opdracht begrijpt.
Automatisch opstartlader-upgrade
Wanneer u voor het eerst een upgrade uitvoert van de huidige Cisco IOS® XE release op uw switch naar een latere of nieuwere release, kan de bootloader automatisch worden bijgewerkt, op basis van de hardwareversie van de switch. Als de bootloader wordt geüpgraded, herlaadt de supervisor automatisch om de nieuwe bootloader toe te laten. Als u daarna teruggaat naar de oudere release, wordt de laarslader niet gedowngraded. De bijgewerkte laarslader ondersteunt alle vorige releases.
Voor volgende versies van Cisco IOS® XE Everest 16.x.x, als er een nieuwe bootloader in die release is, kan deze automatisch worden geüpgraded op basis van de hardwareversie van de switch wanneer u uw switch voor het eerst opstart met de nieuwe afbeelding.
Op het moment dat u een upgrade uitvoert van Cisco IOS® XE Everest 16.6.1 naar 16.6.2, kan een upgrade enige tijd in beslag nemen, terwijl het systeem drie keer wordt hersteld, vanwege de CPLD-upgrade (Common and Complex Programmable Logic Device). Stateful switchover wordt ondersteund vanuit Cisco IOS® XE Everest 16.6.2.
In Catalyst 9400 switch kunt u de supervisor opstarten met het gebruik van twee methoden:
Wanneer de switch in de installatiemodus wordt uitgevoerd, worden Cisco IOS® XE-pakketbestanden (.pkg) en provisioningbestanden (packet.conf) opgeslagen in het flitsgeheugen op de systeemkaart (flash:). Wanneer de switch met het gebruik van .bin-bestand wordt opgestart, wordt het opstartbestand van Cisco IOS® XE-softwarebundel (.bin) opgeslagen in een flash-geheugen op de systeemkaart (flash:).
Na de upgrade van 16.6.2 werkt de procedure ongeacht welke opstartmethode werd gebruikt om de switch op te starten op de huidige 16.6.1-afbeelding. Echter, de procedure hier upgrades de supervisor engine om te installeren modus.
Opmerking: sla deze stap niet over. Zorg ervoor dat u ten minste 1 GB ruimte in de flitser hebt om een nieuw beeld uit te vouwen. Reinig oude installatiebestanden als er onvoldoende ruimte is.
Switch#install remove inactive Cleaning up unnecessary package files No path specified, can use booted path flash:packages.conf Cleaning flash: Scanning boot directory for packages ... done. Preparing packages list to delete ... cat9k-cc_srdriver.16.06.01.SPA.pkg File is in use, cannot delete. cat9k-espbase.16.06.01.SPA.pkg File is in use, can not delete. cat9k-rpbase.16.06.01.SPA.pkg File is in use, cannot delete. cat9k-rpboot.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipspa.16.06.01.SPA.pkg File is in use, will not delete. cat9k-srdriver.B16.06.01.SPA.pkg File is in use, will not delete. cat9k-webui.16.06.01.SPA.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. The following files will be deleted: [R0]: /flash/cat9k-cc_srdriver.16.06.01.SPA.pkg /flash/cat9k-espbase.16.06.01.SPA.pkg /flash/cat9k-rpbase.16.06.01.SPA.pkg /flash/cat9k-rpboot.16.06.01.SPA.pkg /flash/cat9k-sipbase.16.06.01.SPA.pkg /flash/cat9k-sipspa.16.06.01.SPA.pkg /flash/cat9k-srdriver.16.06.01.SPA.pkg /flash/cat9k-webui.16.06.01.SPA.pkg /flash/cat9k_1.bin /flash/cat9k_1.conf /flash/cat9k_2.1.conf /flash/cat9k_2.bin /flash/cat9k_2.conf /flash/cat9k_iosxe.16.06.01.SSA.bin /flash/packages.conf.00- Do you want to remove the above files? [y/n]y [R0]: Deleting file flash:cat9k-cc_srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-espbase.16.06.01.SPA.pkg ... done. Deleting file Deleting file flash:cat9k-rpbase.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-rpboot.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipbase.B16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipspa.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-webui.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k_1.bin ... done. Deleting file flash:cat9k_1.conf ... done. Deleting file flash:cat9k_2.1.conf ... done. Deleting file flash:cat9k_2.bin ... done. Deleting file flash:cat9k_2.conf ... done. Deleting file flash:cat9k_iosxe.16.06.01.SSA.bin ... done. Deleting file flash:packages.conf.00- ... done. SUCCESS: Files deleted. --- Starting Post_Remove_Cleanup --- Performing Post_Remove_Cleanup on Active/Standby [R0] Post_Remove_Cleanup package(s) on R0 [R0] Finished Post_Remove_Cleanup on R0 Checking status of Post_Remove_Cleanup on [R0] Post_Remove_Cleanup: Passed on [R0] Finished Post_Remove_Cleanup SUCCESS: install_remove Tue Jun 20 14:16:29 PDT 2017
In dit voorbeeld kopieert u de afbeelding van TFTP-server naar de bootflash van de supervisor.
Switch#copy tftp: bootflash: Address or name of remote host []? 172.16.53.46 Source filename []? cat9k_iosxe.16.06.02.SPA.bin Destination filename [cat9k_iosxe.16.06.02.SPA.bin]? Accessing tftp://172.16.53.46//cat9k_iosxe.16.06.02.SPA.bin... Loading /cat9k_iosxe.16.06.02.SPA.bin from 10.8.0.6 (via GigabitEthernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 601216545 bytes] 601216545 bytes copied in 50.649 secs (11870255 bytes/sec)
Step 3. Use the dir flash command to confirm that the image has been successfully copied to flash. Switch#dir bootflash:*.bin Directory of bootflash:/*.bin Directory of flash:/ 434184 -rw- 601216545 Jul 26 2017 10:18:11 -07:00 cat9k_iosxe.16.06.02.SPA.bin 11353194496 bytes total (8976625664 bytes free)
Zorg ervoor dat de laarsverklaring wordt gevormd aan pack.conf alvorens u 16.6.2 in installeermodus bevordert. Als het bestand is ingesteld op .bin, moet u het wijzigen in pack.conf.
Switch#show boot
BOOT variable = bootflash:cat9k_iosxe.16.06.01.SPA.bin;
Configuration Register is 0x102
MANUAL_BOOT variable = no
BAUD variable = 9600
ENABLE_BREAK variable does not exist
CONFIG_FILE variable does not exist
Change boot variable to point to packages.conf
Switch(config)#no boot system
Switch(config)#boot system bootflash:packages.conf
*Nov 14 15:12:50.043: %SYS-5-CONFIG_I: Configured from console by consol
Please save the configuration to reflect the new boot variable.
Switch#wr mem
Building configuration...
[OK]
Switch#show boot
BOOT variable = bootflash:packages.conf;
Configuration Register is 0x102
MANUAL_BOOT variable = no >> If manual variable is set to no, it means system is set to auto boot
BAUD variable = 9600
ENABLE_BREAK variable does not exist
CONFIG_FILE variable does not exist
You can set the system to auto boot or manual boot by setting the variables:
Changing system to auto boot
Switch(config)#no boot manual
Changing system to manual boot
Switch(config)#boot manual
If your switches are configured with auto boot, then the switch will automatically boot up with the new image when the switch is
reloaded. If your switches are not configured with auto boot and the switch is reloaded, you will receive a Rommon prompt
where you must then manually boot the new image flash:packages.conf
Switch: boot flash:packages.conf"
Gebruik het installatiebestand toevoegen om de opdracht commit te activeren om de doelafbeelding te installeren naar flash. U kunt wijzen naar de bronafbeelding op uw TFTP-server of in bootflitser als u de afbeelding hebt gekopieerd naar flitser. In dit voorbeeld hebt u de afbeelding al naar de flitser gekopieerd.
Switch#install add file bootflash:cat9k_iosxe.16.06.02.SPA.bin activate commit install_add_activate_commit: START Fri Nov 13 22:34:41 UTC 2017 *Nov 13 22:34:21.543: %IOSXE-5-PLATFORM: R0/0: Nov 13 22:34:21 install_engine.sh: %INSTALL-5-INSTALL_START_INFO: Started install one-shot flash:cat9k_iosxe.16.06.02.SPA.bininstall_add_activate_commit: Adding PACKAGE
This operation requires a reload of the system. Do you want to proceed?
Please confirm you have changed boot config to flash:packages.conf [y/n]y
--- Starting Add ---
Performing Add on Active/Standby
[R0] Add package(s) on R0
[R0] Finished Add on R0
Checking status of Add on [R0]
Add: Passed on [R0]
Finished Add
install_add_activate_commit: Activating PACKAGE
*Nov 13 22:37:09.730: %IOSXE-4-PLATFORM: R0/0: kernel: ISOFS: Unable to identify CD-ROM format.Following packages shall be activated:
/flash/cat9k-wlc.16.06.02.SPA.pkg
/flash/cat9k-webui.16.06.02.SPA.pkg
/flash/cat9k-srdriver.16.06.02.SPA.pkg
/flash/cat9k-sipspa.16.06.02.SPA.pkg
/flash/cat9k-sipbase.16.06.02.SPA.pkg
/flash/cat9k-rpboot.16.06.02.SPA.pkg
/flash/cat9k-rpbase.16.06.02.SPA.pkg
/flash/cat9k-guestshell.16.06.02.SPA.pkg
/flash/cat9k-espbase.16.06.02.SPA.pkg
/flash/cat9k-cc_srdriver.16.06.02.SPA.pkg
This operation requires a reload of the system. Do you want to proceed? [y/n]y
--- Starting Activate ---
Performing Activate on Active/Standby
[R0] Finished Activate on R0
Checking status of Activate on [R0]
Activate: Passed on [R0]
Finished Activate
--- Starting Commit ---
Performing Commit on Active/Standby
*Nov 13 22:38:40.654: %IOSXE-5-PLATFORM: R0/0: Nov 13 22:38:40 rollback_timer.sh: %INSTALL-5-INSTALL_AUTO_ABORT_TIMER_PROGRESS: Install auto abort timer will expire in 7200 seconds [R0] Commit package(s) on R0
[R0] Finished Commit on R0
Checking status of Commit on [R0]
Commit: Passed on [R0]
Finished Commit
Install will reload the system now!
SUCCESS: install_add_activate_commit Mon Nov 13 22:39:07 UTC 2017
*Nov 13 22:39:07.715: %IOSXE-5-PLATFORM: R0/0: Nov 13 22:39:07 install_engine.sh: %INSTALL-5-INSTALL_COMPLETED_INFO: Completed install one-shot PACKAGE flash:cat9k_iosxe.16.06.02.SPA.binNov 13 22:39:2
Initializing Hardware...
System Bootstrap, Version 16.6.1r [FC2], RELEASE SOFTWARE (P)
Compiled Sat 07/15/2017 10:06:12.23 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
#######################################################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
Warning: ignoring ROMMON var "USER_BOOT_PARAM"
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/0): ### Mon Nov 13 22:42:05 Universal 2017 PLEASE DO NOT POWER CYCLE ### BOOT LOADER UPGRADING
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/0): boot loader upgrade successful <<< Bootloader upgrade done
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/0): Reloading the Supervisor to enable the New BOOTLOADER
Initializing Hardware...
Initializing Hardware...
Initializing Hardware...
System Bootstrap, Version 16.6.2r[FC1], RELEASE SOFTWARE (P)
Compiled Tue 10/31/2017 11:38:44.98 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
######################################################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
Warning: ignoring ROMMON var "USER_BOOT_PARAM"
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
Nadat de software met succes is geïnstalleerd, verifieert dat de flitsverdeling de nieuwe .pkg dossiers heeft. Je kunt de voorbeelduitvoer hier zien.
Switch#dir bootflash:*.pkg
Directory of bootflash:/*.pkg
Directory of bootflash:/
405607 -rw- 5186504 Nov 13 2017 22:36:25 +00:00 cat9k-cc_srdriver.16.06.02.SPA.pkg
405608 -rw- 76649412 Nov 13 2017 22:36:27 +00:00 cat9k-espbase.16.06.02.SPA.pkg
405609 -rw- 1536964 Nov 13 2017 22:36:27 +00:00 cat9k-guestshell.16.06.02.SPA.pkg
405610 -rw- 380625856 Nov 13 2017 22:36:38 +00:00 cat9k-rpbase.16.06.02.SPA.pkg
405616 -rw- 29580684 Nov 13 2017 22:36:48 +00:00 cat9k-rpboot.16.06.02.SPA.pkg
405611 -rw- 27612100 Nov 13 2017 22:36:39 +00:00 cat9k-sipbase.16.06.02.SPA.pkg
405614 -rw- 12268480 Nov 13 2017 22:36:41 +00:00 cat9k-webui.16.06.02.SPA.pkg
405612 -rw- 54981568 Nov 13 2017 22:36:40 +00:00 cat9k-sipspa.16.06.02.SPA.pkg
405613 -rw- 6521796 Nov 13 2017 22:36:40 +00:00 cat9k-srdriver.16.06.02.SPA.pkg
405615 -rw- 1536960 Nov 13 2017 22:36:41 +00:00 cat9k-wlc.16.06.02.SPA.pkg
11250098176 bytes total (8812113920 bytes free)
Wanneer het nieuwe beeld wordt opgestart, verifieert u de versie van het nieuwe beeld met behulp van de opdracht show version:
Opmerking: wanneer u de nieuwe afbeelding opstart, wordt bootloader automatisch bijgewerkt.
Switch#show version Cisco IOS® XE Software, Version 16.06.02 Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2017 by Cisco Systems, Inc. Compiled Wed 01-Nov-17 07:26 by mcpre Cisco IOS® XE software, Copyright (c) 2005-2017 by Cisco Systems, Inc. All rights reserved. Certain components of Cisco IOS®-XE software are licensed under the GNU General Public License ("GPL") Version 2.0. The software code licensed under GPL Version 2.0 is free software that comes with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or "License Notice" file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. ROM: IOS-XE ROMMON BOOTLDR: System Bootstrap, Version 16.6.2r[FC1], RELEASE SOFTWARE (P) Switch uptime is 20 minutes Uptime for this control processor is 22 minutes System returned to ROM by reload System image file is "bootflash:packages.conf" Last reload reason: EHSA standby down This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products can be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. Technology Package License Information: ----------------------------------------------------------------- Technology-package Technology-package Current Type Next reboot ------------------------------------------------------------------ network-advantage Permanent network-advantage cisco C9410R (X86) processor (revision V01) with 869104K/6147K bytes of memory. Processor board ID FXS2130Q28F 2 Virtual Ethernet interfaces 192 Gigabit Ethernet interfaces 16 Ten Gigabit Ethernet interfaces 4 Forty Gigabit Ethernet interfaces 32768K bytes of non-volatile configuration memory. 15958488K bytes of physical memory. 11161600K bytes of Bootflash at bootflash:. 1638400K bytes of Crash Files at crashinfo:. 0K bytes of WebUI ODM Files at webui:. Configuration register is 0x2
Switch#show module
Chassis Type: C9410R
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+--------------+--------------
1 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409NQ
2 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409N2
3 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1R
4 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1C
5 10 Supervisor 1 Module C9400-SUP-1 JAE2124023Z
Mod MAC addresses Hw Fw Sw Status
---+--------------------------------+----+------------+------------------+--------
1 E4AA.5D59.8420 to E4AA.5D59.844F 1.0 16.6.2r[FC1 16.06.02 ok
2 E4AA.5D59.85AC to E4AA.5D59.85DB 1.0 16.6.2r[FC1 16.06.02 ok
3 E4AA.5D59.BC0C to E4AA.5D59.BC3B 1.0 16.6.2r[FC1 16.06.02 ok
4 E4AA.5D59.B72C to E4AA.5D59.B75B 1.0 16.6.2r[FC1 16.06.02 ok
5 2C5A.0F1C.4F2C to 2C5A.0F1C.4F35 0.6 16.6.2r[FC1 16.06.02 ok
Mod Redundancy Role Operating Redundancy Mode Configured Redundancy Mode
---+-------------------+-------------------------+---------------------------
5 Active active sso
Verwijder de supervisor uit sleuf 5 die in vorige stappen is opgewaardeerd en plaats de standby supervisor in sleuf 6 in het chassis. De verwijdering van eerste supervisor is belangrijk omdat twee supervisors te verbeteren terwijl beiden in het chassis worden opgenomen niet wordt gesteund zoals eerder vermeld. U kunt de zelfde hier gedocumenteerde verbeteringsstappen herhalen om de onlangs opgenomen supervisor te bevorderen.
Opmerking: sla deze stap niet over. Zorg ervoor dat u ten minste 1 GB ruimte in de flitser hebt om een nieuw beeld uit te vouwen. Reinig oude installatiebestanden als er onvoldoende ruimte is.
Switch#install remove inactive Cleaning up unnecessary package files No path specified, will use booted path flash:packages.conf Cleaning flash: Scanning boot directory for packages ... done. Preparing packages list to delete ... cat9k-cc_srdriver.16.06.01.SPA.pkg File is in use, will not delete. cat9k-espbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-rpbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-rpboot.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipbase.16.06.01.SPA.pkg File is in use, will not delete. cat9k-sipspa.16.06.01.SPA.pkg File is in use, will not delete. cat9k-srdriver.B16.06.01.SPA.pkg File is in use, will not delete. cat9k-webui.16.06.01.SPA.pkg File is in use, will not delete. packages.conf File is in use, will not delete. done. The following files will be deleted: [R0]: /flash/cat9k-cc_srdriver.16.06.01.SPA.pkg /flash/cat9k-espbase.16.06.01.SPA.pkg /flash/cat9k-rpbase.16.06.01.SPA.pkg /flash/cat9k-rpboot.16.06.01.SPA.pkg /flash/cat9k-sipbase.16.06.01.SPA.pkg /flash/cat9k-sipspa.16.06.01.SPA.pkg /flash/cat9k-srdriver.16.06.01.SPA.pkg /flash/cat9k-webui.16.06.01.SPA.pkg /flash/cat9k_1.bin /flash/cat9k_1.conf /flash/cat9k_2.1.conf /flash/cat9k_2.bin /flash/cat9k_2.conf /flash/cat9k_iosxe.16.06.01.SSA.bin /flash/packages.conf.00- Do you want to remove the above files? [y/n]y [R0]: Deleting file flash:cat9k-cc_srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-espbase.16.06.01.SPA.pkg ... done. Deleting file Deleting file flash:cat9k-rpbase.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-rpboot.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipbase.B16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-sipspa.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-srdriver.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k-webui.16.06.01.SPA.pkg ... done. Deleting file flash:cat9k_1.bin ... done. Deleting file flash:cat9k_1.conf ... done. Deleting file flash:cat9k_2.1.conf ... done. Deleting file flash:cat9k_2.bin ... done. Deleting file flash:cat9k_2.conf ... done. Deleting file flash:cat9k_iosxe.16.06.01.SSA.bin ... done. Deleting file flash:packages.conf.00- ... done. SUCCESS: Files deleted. --- Starting Post_Remove_Cleanup --- Performing Post_Remove_Cleanup on Active/Standby [R0] Post_Remove_Cleanup package(s) on R0 [R0] Finished Post_Remove_Cleanup on R0 Checking status of Post_Remove_Cleanup on [R0] Post_Remove_Cleanup: Passed on [R0] Finished Post_Remove_Cleanup SUCCESS: install_remove Tue Jun 20 14:16:29 PDT 2017
In dit voorbeeld kopieert u de afbeelding van TFTP-server naar de flitser van de supervisor.
Switch#copy tftp: bootflash: Address or name of remote host []? 172.16.53.46 Source filename []? cat9k_iosxe.16.06.02.SPA.bin Destination filename [cat9k_iosxe.16.06.02.SPA.bin]? Accessing tftp://172.16.53.46//cat9k_iosxe.16.06.02.SPA.bin... Loading /cat9k_iosxe.16.06.02.SPA.bin from 10.8.0.6 (via GigabitEthernet0/0):
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 601216545 bytes] 601216545 bytes copied in 50.649 secs (11870255 bytes/sec) Step 3 Use the dir flash command to confirm that the image has been successfully copied to flash. Switch#dir bootflash:*.bin Directory of bootflash:/*.bin Directory of flash:/ 434184 -rw- 601216545 Jul 26 2017 10:18:11 -07:00 cat9k_iosxe.16.06.02.SPA.bin 11353194496 bytes total (8976625664 bytes free)
Zorg ervoor dat de laarsverklaring wordt gevormd aan pack.conf alvorens u 16.6.2 in installeermodus bevordert. Als deze optie is ingesteld op .bin, moet u deze wijzigen in pack.conf.
Switch#show boot BOOT variable = bootflash:packages.conf; Configuration Register is 0x2 MANUAL_BOOT variable = no BAUD variable = 9600 ENABLE_BREAK variable = BOOTMODE variable does not exist IPXE_TIMEOUT variable does not exist CONFIG_FILE variable = If your switches are configured with auto boot, then the switch automatically boots up with the new image.
If not, you can manually boot flash:packages.conf Switch: boot flash:packages.conf
Gebruik install add file activation commit opdracht om de doelafbeelding te installeren om te flitsen. U kunt naar de bronafbeelding wijzen op uw TFTP-server of in bootflash als u de afbeelding hebt gekopieerd naar flash. In dit voorbeeld hebt u de afbeelding al naar de flitser gekopieerd.
Switch#install add file bootflash:cat9k_iosxe.16.06.02.SPA.bin activate commit
install_add_activate_commit: START Mon Nov 13 23:24:02 UTC 2017
System configuration has been modified.
Press Yes(y) to save the configuration and proceed.
Press No(n) for proceeding without saving the configuration.
Press Quit(q) to exit, you can save configuration and re-enter the command. [y/n/q]y
Building configuration...
[OK]Modified configuration has been saved
*Nov 13 23:24:09.935: %SYS-2-PRIVCFG_ENCRYPT: Successfully encrypted private config file
*Nov 13 23:24:11.314: %IOSXE-5-PLATFORM: R1/0: Nov 13 23:24:11 install_engine.sh: %INSTALL-5-INSTALL_START_INFO: Started install one-shot flash:cat9k_iosxe.16.06.02.SPA.bininstall_add_activate_commit: Adding PACKAGE
This operation requires a reload of the system. Do you want to proceed?
Please confirm you have changed boot config to flash:packages.conf [y/n]y
--- Starting Add ---
Performing Add on Active/Standby
[R1] Add package(s) on R1
[R1] Finished Add on R1
Checking status of Add on [R1]
Add: Passed on [R1]
Finished Add
install_add_activate_commit: Activating PACKAGE
*Nov 13 23:25:28.589: %IOSXE-4-PLATFORM: R1/0: kernel: ISOFS: Unable to identify CD-ROM format.Following packages shall be activated:
/flash/cat9k-wlc.16.06.02.SPA.pkg
/flash/cat9k-webui.16.06.02.SPA.pkg
/flash/cat9k-srdriver.16.06.02.SPA.pkg
/flash/cat9k-sipspa.16.06.02.SPA.pkg
/flash/cat9k-sipbase.16.06.02.SPA.pkg
/flash/cat9k-rpboot.16.06.02.SPA.pkg
/flash/cat9k-rpbase.16.06.02.SPA.pkg
/flash/cat9k-guestshell.16.06.02.SPA.pkg
/flash/cat9k-espbase.16.06.02.SPA.pkg
/flash/cat9k-cc_srdriver.16.06.02.SPA.pkg
This operation requires a reload of the system. Do you want to proceed? [y/n]y
--- Starting Activate ---
Performing Activate on Active/Standby
[R1] Activate package(s) on R1
head: invalid number of lines: '/tmp/Activate.rp-1-1-1.20171113232845.out.log'
[R1] Finished Activate on R1
Checking status of Activate on [R1]
Activate: Passed on [R1]
Finished Activate
--- Starting Commit ---
Performing Commit on Active/Standby
*Nov 13 23:28:47.521: %IOSXE-5-PLATFORM: R1/0: Nov 13 23:28:47 rollback_timer.sh: %INSTALL-5-INSTALL_AUTO_ABORT_TIMER_PROGRESS: Install auto abort timer will expire in 7200 seconds[R1] Commit package(s) on R1
[R1] Finished Commit on R1
Checking status of Commit on [R1]
Commit: Passed on [R1]
Finished Commit
Install will reload the system now!
SUCCESS: install_add_activate_commit Mon Nov 13 23:29:14 UTC 2017
Switch#
*Nov 13 23:29:14.578: %IOSXE-5-PLATFORM: R1/0: Nov 13 23:29:14 install_engine.sh: %INSTALL-5-INSTALL_COMPLETED_INFO: Completed install one-shot PACKAGE flash:cat9k_iosxe.16.06.02.SPA.binNov 13 23:29:27
Initializing Hardware...
System Bootstrap, Version 16.6.1r [FC2], RELEASE SOFTWARE (P)
Compiled Sat 07/15/2017 10:06:12.23 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
#######################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/1): ### Mon Nov 13 23:32:20 Universal 2017 PLEASE DO NOT POWER CYCLE ### BOOT LOADER UPGRADING
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/1): boot loader upgrade successful << Bootloader upgrade done
%IOSXEBOOT-4-BOOTLOADER_UPGRADE: (rp/1): Reloading the Supervisor to enable the New BOOTLOADER
Initializing Hardware...
Initializing Hardware...
Initializing Hardware...
System Bootstrap, Version 16.6.2r[FC1], RELEASE SOFTWARE (P)
Compiled Tue 10/31/2017 11:38:44.98 by rel
Current image running:
Primary Rommon Image
Last reset cause: SoftwareResetTrig
C9400-SUP-1 platform with 16777216 Kbytes of main memory
Preparing to autoboot. [Press Ctrl-C to interrupt] 0
attempting to boot from [bootflash:packages.conf]
Located file packages.conf
#
#######################################################################################################################################################################
Validate packages: SHA-1 hash:
calculated 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
expected 550C9730:667B2788:DD6F6B06:D0FFA819:01A315DA
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS® Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
Nadat de software met succes is geïnstalleerd, verifieert dat de flitsverdeling de nieuwe .pkg dossiers heeft. Je kunt de voorbeelduitvoer hier zien.
Switch#dir bootflash:*.pkg Directory of bootflash:/*.pkg Directory of bootflash:/ 405607 -rw- 5186504 Nov 13 2017 22:36:25 +00:00 cat9k-cc_srdriver.16.06.02.SPA.pkg 405608 -rw- 76649412 Nov 13 2017 22:36:27 +00:00 cat9k-espbase.16.06.02.SPA.pkg 405609 -rw- 1536964 Nov 13 2017 22:36:27 +00:00 cat9k-guestshell.16.06.02.SPA.pkg 405610 -rw- 380625856 Nov 13 2017 22:36:38 +00:00 cat9k-rpbase.16.06.02.SPA.pkg 405616 -rw- 29580684 Nov 13 2017 22:36:48 +00:00 cat9k-rpboot.16.06.02.SPA.pkg 405611 -rw- 27612100 Nov 13 2017 22:36:39 +00:00 cat9k-sipbase.16.06.02.SPA.pkg 405614 -rw- 12268480 Nov 13 2017 22:36:41 +00:00 cat9k-webui.16.06.02.SPA.pkg 405612 -rw- 54981568 Nov 13 2017 22:36:40 +00:00 cat9k-sipspa.16.06.02.SPA.pkg 405613 -rw- 6521796 Nov 13 2017 22:36:40 +00:00 cat9k-srdriver.16.06.02.SPA.pkg 405615 -rw- 1536960 Nov 13 2017 22:36:41 +00:00 cat9k-wlc.16.06.02.SPA.pkg 11250098176 bytes total (8812113920 bytes free)
Aangezien beide supervisors individueel worden opgewaardeerd, neem de eerste supervisor in groef 5 op. Het moet toetreden als standby supervisor.
Checking module status with both supervisors inserted Switch#show module Chassis Type: C9410R Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+--------------+-------------- 1 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409NQ 2 48 48-Port 10/100/1000 (RJ-45) C9400-LC-48T JAE212409N2 3 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1R 4 48 48-Port UPOE 10/100/1000 (RJ-45) C9400-LC-48U JAE21270C1C 5 10 Supervisor 1 Module C9400-SUP-1 JAE21240235 6 10 Supervisor 1 Module C9400-SUP-1 JAE21240235 Mod MAC addresses Hw Fw Sw Status ---+--------------------------------+----+------------+------------------+-------- 1 E4AA.5D59.8420 to E4AA.5D59.844F 1.0 16.6.2r[FC1 16.06.02 ok 2 E4AA.5D59.85AC to E4AA.5D59.85DB 1.0 16.6.2r[FC1 16.06.02 ok 3 E4AA.5D59.BC0C to E4AA.5D59.BC3B 1.0 16.6.2r[FC1 16.06.02 ok 4 E4AA.5D59.B72C to E4AA.5D59.B75B 1.0 16.6.2r[FC1 16.06.02 ok 5 2C5A.0F1C.4F2C to 2C5A.0F1C.4F35 0.6 16.6.2r[FC1 16.06.02 ok 6 2C5A.0F1C.4F36 to 2C5A.0F1C.4F3F 0.6 16.6.2r[FC1 16.06.02 ok Mod Redundancy Role Operating Redundancy Mode Configured Redundancy Mode ---+-------------------+-------------------------+--------------------------- 5 Standby standby hot sso 6 Active active sso
De supervisor modules in Catalyst 9400 (hardware) ondersteunen redundantie. Softwareredundantie wordt ondersteund in Cisco IOS ® XE Everest 16.6.2. In softwareversie 16.6.2, wordt de eigenschap van de Redundantie van de RPR niet ondersteund. Gebruik tonen redundantie en tonen platform software iomd redundantie opdrachten om ervoor te zorgen dat zowel Stateful Switchover (SSO) gevormd als IOMD is voordat u overschakelt.
Wanneer een stand-by supervisor engine in RPR-modus draait, wordt deze gestart in een gedeeltelijk geïnitialiseerde toestand en gesynchroniseerd met de permanente configuratie van de actieve supervisor engine. RPR wordt niet ondersteund op de huidige release 16.6.2.
In het geval van de overschakeling van de supervisor motor, wordt het verkeer onderbroken omdat in RPR wijze alle fysieke havens opnieuw beginnen aangezien er geen staat wordt gehandhaafd tussen supervisor motoren die op moduletypes en status betrekking heeft. Na switchover, wanneer de standby supervisor engine zijn initialisatie voltooit, leest het hardware informatie direct van de module en wordt het de actieve supervisor engine.
Wanneer een stand-by supervisor engine in SSO-modus draait, start de stand-by supervisor engine in een volledig geïnitialiseerde toestand en synchroniseert met de permanente configuratie en de actieve configuratie van de actieve supervisor engine. Het onderhoudt vervolgens de status op de hier genoemde protocollen, en alle wijzigingen in hardware en software status voor functies die stateful switchover ondersteunen worden in synchronisatie gehouden.
Dientengevolge, biedt het nul onderbreking aan Layer 2 zittingen in een overtollige supervisor motorconfiguratie aan.
Omdat de standby supervisor engine de hardwareverbindingsstatus van elke link herkent, blijven poorten die actief waren voor de overschakeling, waaronder de uplink-poorten vallen. Omdat uplinkpoorten zich fysiek op de supervisor-engine bevinden, kunnen ze echter worden losgekoppeld als de supervisor-engine wordt verwijderd.
Als de actieve supervisor engine mislukt, wordt de stand-by supervisor engine actief. Deze nieuw actieve supervisor engine gebruikt bestaande Layer 2-switching informatie om het verkeer te blijven doorsturen.
IOMD is Input Output Module Driver software process. Check if IOMds are ready and have initialized Software/hardware. Switch# show platform software iomd redundancy Configured Redundancy Mode = sso Operating Redundancy Mode = sso Local RF state = ACTIVE Peer RF state = STANDBY HOT slot PSM STATE SPA INTF HA_STATE HA_ACTIVE 1 ready started ready 00:10:49 2 ready started ready 00:10:49 3 ready started ready 00:10:48 4 ready started ready 00:10:49 5 ready started ready 00:10:54 6 ready started ready 00:10:53 ***active RP
Switch#show redundancy
Redundant System Information :
------------------------------
Available system uptime = 31 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
-------------------------------
Active Location = slot 6
Current Software state = ACTIVE
Uptime in current state = 31 minutes
Image Version = Cisco IOS ®Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
BOOT = bootflash:packages.conf;
CONFIG_FILE =
Configuration register = 0x2
Peer Processor Information :
----------------------------
Standby Location = slot 5
Current Software state = STANDBY HOT
Uptime in current state = 26 minutes
Image Version = Cisco IOS ®Software [Everest], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.6.2,
RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Wed 01-Nov-17 07:26 by mcpre
BOOT = bootflash:packages.conf;
CONFIG_FILE =
Configuration register = 0x2
Revisie | Publicatiedatum | Opmerkingen |
---|---|---|
2.0 |
05-May-2023 |
Bijgewerkte Titel, het Brandmerken Vereisten, Machinevertaling, Rondes, Stijlvereisten, en het Opmaken. |
1.0 |
16-Nov-2017 |
Eerste vrijgave |