この設定例では、リモート PIX が Dynamic Host Configuration Protocol(DHCP; ダイナミック ホスト制御プロトコル)を介して IP アドレスを受信し、セントラル PIX に接続しています。この設定により、中央 PIX がダイナミック IPSec 接続を受け入れることができます。リモート PIX では、Network Address Translation(NAT; ネットワーク アドレス変換)を使用して、背後にあるプライベート アドレスの付けられたデバイスが、セントラル PIX の背後にあるプライベート アドレスの付けられたネットワークに「参加」できるようにしています。リモート PIX は、セントラル PIX への接続を開始できますが(エンド ポイントがわかっているので)、セントラル PIX 側からはリモート PIX への接続を開始できません(エンド ポイントがわからないため)。
この設定例では、Tiger がリモート PIX、Lion が中央 PIX です。TigerのIPアドレスは不明なので、ワイルドカード事前共有キーを知っているどこからでも動的に接続を受け入れるようにLionを設定する必要があります。Tigerは、暗号化するトラフィック(アクセスリストによって指定されるため)と、Lionエンドポイントの場所を認識します。Tiger が接続を開始する必要があります。両側でNATとnat 0を実行し、IPsecトラフィックのNATをバイパスします。
また、この設定では、リモート ユーザは、Cisco VPN Client 3.x を使用してセントラル PIX(Lion)に接続します。リモートユーザはリモートPIX(Tiger)に接続できません。両側に動的にIPアドレスが割り当てられ、要求の送信先が認識されないためです。
Cisco VPN Client 4.xを使用するPIX/ASA 7.xでの同じシナリオの詳細については、『NATおよびVPN Clientを使用したPIX/ASA 7.x PIX-to-PIXダイナミックからスタティックへのIPSecの設定例』を参照してください。
このドキュメントに特有の要件はありません。
このドキュメントの情報は、次のソフトウェアとハードウェアのバージョンに基づいています。
Cisco PIX ファイアウォール ソフトウェア リリース 6.0(1)(Cisco VPN Client 3.x にはそれ以上)
Cisco PIX ファイアウォール ソフトウェア リリース 5.3.1(リモート PIX)
Cisco VPN Client バージョン 3.X
このドキュメントの情報は、特定のラボ環境にあるデバイスに基づいて作成されました。このドキュメントで使用するすべてのデバイスは、初期(デフォルト)設定の状態から起動しています。対象のネットワークが実稼働中である場合には、どのようなコマンドについても、その潜在的な影響について確実に理解しておく必要があります。
ドキュメント表記の詳細は、『シスコ テクニカル ティップスの表記法』を参照してください。
このセクションでは、このドキュメントで説明する機能を設定するために必要な情報を提供しています。
注:このセクションで使用されているコマンドの詳細を調べるには、Command Lookup Tool(登録ユーザ専用)を参照してください。一部ツールについては、ゲスト登録のお客様にはアクセスできない場合がありますことをご了承ください。
このドキュメントでは、次のネットワーク セットアップを使用します。
Lion の設定 |
---|
Building configuration... : Saved : PIX Version 6.0(1) nameif gb-ethernet0 spare1 security10 nameif gb-ethernet1 spare2 security15 nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted hostname lion domain-name cisco.com fixup protocol ftp 21 fixup protocol http 80 fixup protocol h323 1720 fixup protocol rsh 514 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol sip 5060 fixup protocol skinny 2000 names ! !--- ACL to avoid Network Address Translation (NAT) on the IPsec packets. access-list 100 permit ip 10.2.2.0 255.255.255.0 10.1.1.0 255.255.255.0 access-list 100 permit ip 10.2.2.0 255.255.255.0 10.3.3.0 255.255.255.0 ! pager lines 24 logging buffered debugging interface gb-ethernet0 1000auto shutdown interface gb-ethernet1 1000auto shutdown interface ethernet0 10baset interface ethernet1 10baset mtu spare1 1500 mtu spare2 1500 mtu outside 1500 mtu inside 1500 ip address spare1 127.0.0.1 255.255.255.255 ip address spare2 127.0.0.1 255.255.255.255 ! !--- IP addresses on the interfaces ip address outside 203.1.1.1 255.255.255.0 ip address inside 10.2.2.1 255.255.255.0 ! ip audit info action alarm ip audit attack action alarm ip local pool clientpool 10.3.3.1-10.3.3.10 no failover failover timeout 0:00:00 failover poll 15 failover ip address spare1 0.0.0.0 failover ip address spare2 0.0.0.0 failover ip address outside 0.0.0.0 failover ip address inside 0.0.0.0 pdm history enable arp timeout 14400 !--- global (outside) 1 203.1.1.10-203.1.1.15 !--- Change from NAT to PAT on the DHCP interface. global (outside) 1 interface ! !--- Binding ACL 100 to the NAT statement to avoid NAT on the IPsec packets. nat (inside) 0 access-list 100 ! nat (inside) 1 0.0.0.0 0.0.0.0 0 0 conduit permit icmp any any ! !--- Default route to the Internet route outside 0.0.0.0 0.0.0.0 203.1.1.2 1 ! timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable ! !--- The sysopt command avoids conduit on the IPsec encrypted traffic. sysopt connection permit-ipsec ! no sysopt route dnat ! !--- Phase 2 encryption type crypto ipsec transform-set myset esp-des esp-md5-hmac crypto dynamic-map cisco 1 set transform-set myset crypto map dyn-map 20 ipsec-isakmp dynamic cisco ! !--- Binds the IPsec engine on the outside interface. crypto map dyn-map interface outside ! !--- Enables ISAKMP key-exchange. isakmp enable outside ! !--- ISAKMP policy for accepting dynamic connections from the remote PIX. isakmp key ******** address 0.0.0.0 netmask 0.0.0.0 !--- ISAKMP policy for Cisco VPN Client 2.x isakmp policy 10 authentication pre-share isakmp policy 10 encryption des isakmp policy 10 hash md5 isakmp policy 10 group 1 isakmp policy 10 lifetime 1000 ! !--- ISAKMP policy for Cisco VPN Client 3.x isakmp policy 20 authentication pre-share isakmp policy 20 encryption des isakmp policy 20 hash sha isakmp policy 20 group 2 isakmp policy 20 lifetime 86400 ! !--- IPsec group configuration for either client vpngroup unityclient address-pool clientpool vpngroup unityclient dns-server 10.1.1.3 vpngroup unityclient wins-server 10.1.1.3 vpngroup unityclient default-domain cisco.com vpngroup unityclient idle-time 1800 vpngroup unityclient password ******** ! telnet timeout 5 ssh timeout 5 terminal width 80 Cryptochecksum:d6fe92db883a052c5765be21a74e7c8d : end [OK] |
Tiger の設定 |
---|
Building configuration... : Saved : PIX Version 5.3(1) nameif gb-ethernet0 spare1 security10 nameif gb-ethernet1 spare2 security15 nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password 8Ry2YjIyt7RRXU24 encrypted passwd 2KFQnbNIdI.2KYOU encrypted hostname tiger fixup protocol ftp 21 fixup protocol http 80 fixup protocol h323 1720 fixup protocol rsh 514 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol sip 5060 names ! !--- ACL to avoid NAT on the IPsec packets access-list 101 permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0 ! pager lines 24 logging on no logging timestamp no logging standby no logging console no logging monitor logging buffered debugging no logging trap no logging history logging facility 20 logging queue 512 interface gb-ethernet0 1000auto shutdown interface gb-ethernet1 1000auto shutdown interface ethernet0 10baset interface ethernet1 10baset mtu spare1 1500 mtu spare2 1500 mtu outside 1500 mtu inside 1500 ip address spare1 127.0.0.1 255.255.255.255 ip address spare2 127.0.0.1 255.255.255.255 ! ip address outside dhcp ip address inside 10.1.1.1 255.255.255.0 ! ip audit info action alarm ip audit attack action alarm no failover failover timeout 0:00:00 failover poll 15 failover ip address spare1 0.0.0.0 failover ip address spare2 0.0.0.0 failover ip address outside 0.0.0.0 failover ip address inside 0.0.0.0 arp timeout 14400 global (outside) 1 204.1.1.10-204.1.1.15 ! !--- Binds ACL 101 to the NAT statement to avoid NAT on the IPsec packets. nat (inside) 0 access-list 101 ! nat (inside) 1 0.0.0.0 0.0.0.0 0 0 conduit permit icmp any any route outside 0.0.0.0 0.0.0.0 204.1.1.2 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable ! !--- The sysopt command avoids conduit on the IPsec encrypted traffic. sysopt connection permit-ipsec ! no sysopt route dnat ! !--- Phase 2 encryption type crypto ipsec transform-set myset esp-des esp-md5-hmac crypto map newmap 10 ipsec-isakmp crypto map newmap 10 match address 101 crypto map newmap 10 set peer 203.1.1.1 crypto map newmap 10 set transform-set myset ! !--- Binds the IPsec engine on the outside interface. crypto map newmap interface outside ! !--- Enables ISAKMP key-exchange isakmp enable outside ! !--- ISAKMP policy for connecting to the central PIX. isakmp key ******** address 203.1.1.1 netmask 255.255.255.255 isakmp identity hostname isakmp policy 10 authentication pre-share isakmp policy 10 encryption des isakmp policy 10 hash md5 isakmp policy 10 group 1 isakmp policy 10 lifetime 1000 ! telnet timeout 5 ssh timeout 5 terminal width 80 Cryptochecksum:6743b7bf9476590ecd1a1a8c6d75245b : end [OK] |
この項では、設定が正常に動作しているかどうかを確認する際に役立つ情報を紹介しています。
アウトプット インタープリタ ツール(登録ユーザ専用)(OIT)は、特定の show コマンドをサポートします。OIT を使用して、show コマンドの出力の分析を表示します。
注:clearコマンドはconfigモードで実行する必要があります。
clear crypto ipsec sa:VPN トンネルのネゴシエーションが失敗した後で、IPSec アソシエーションをリセットします。
clear crypto isakmp sa:VPN トンネルのネゴシエーションが失敗した後で、Internet Security Association and Key Management Protocol(ISAKMP)セキュリティ アソシエーションをリセットします。
show crypto engine ipsec:暗号化されたセッションを表示します。
ここでは、設定のトラブルシューティングに使用できる情報を示します。
アウトプット インタープリタ ツール(登録ユーザ専用)(OIT)は、特定の show コマンドをサポートします。OIT を使用して、show コマンドの出力の分析を表示します。
注:debug コマンドを使用する前に、『debug コマンドの重要な情報』を参照してください。
debug crypto ipsec:クライアントが VPN 接続の IPSec 部分をネゴシエートしているかどうかを確認するときに使用します。
debug crypto isakmp connection:ピアがVPNのISAKMP部分をネゴシエートしているかどうかを確認するために使用します。
crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1 OAK_MM exchange ISAKMP (0): processing SA payload. message ID = 0 ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy ISAKMP: encryption DES-CBC ISAKMP: hash MD5 ISAKMP: default group 1 ISAKMP: auth pre-share ISAKMP: life type in seconds ISAKMP: life duration (basic) of 1000 ISAKMP (0): atts are acceptable. Next payload is 0 ISAKMP (0): SA is doing pre-shared key authentication using id type ID_FQDN return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1 OAK_MM exchange ISAKMP (0): processing KE payload. message ID = 0 ISAKMP (0): processing NONCE payload. message ID = 0 ISAKMP (0): processing vendor id payload ISAKMP (0): processing vendor id payload ISAKMP (0): processing vendor id payload ISAKMP (0): speaking to another IOS box! return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1 OAK_MM exchange ISAKMP (0): processing ID payload. message ID = 0 ISAKMP (0): processing HASH payload. message ID = 0 ISAKMP (0): SA has been authenticated ISAKMP (0): ID payload next-payload : 8 type : 2 protocol : 17 port : 500 length : 10 ISAKMP (0): Total payload length: 14 return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1 OAK_QM exchange oakley_process_quick_mode: OAK_QM_IDLE ISAKMP (0): processing SA payload. message ID = 1223411072 ISAKMP : Checking IPSec proposal 1 ISAKMP: transform 1, ESP_DES ISAKMP: attributes in transform: ISAKMP: encaps is 1 ISAKMP: SA life type in seconds ISAKMP: SA life duration (basic) of 28800 ISAKMP: SA life type in kilobytes ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0 ISAKMP: authenticator is HMAC-MD5 ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1, (key eng. msg.) dest= 203.1.1.1, src= 204.1.1.1, dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), protocol= ESP, transform= esp-des esp-md5-hmac , lifedur= 0s and 0kb, spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4 ISAKMP (0): processing NONCE payload. message ID = 1223411072 ISAKMP (0): processing ID payload. message ID = 1223411072 ISAKMP (0): ID_IPV4_ADDR_SUBNET src 10.2.2.0/255.255.255.0 prot 0 port 0 ISAKMP (0): processing ID payload. message ID = 1223411072 ISAKMP (0): ID_IPV4_ADDR_SUBNET dst 10.1.1.0/255.255.255.0 prot 0 port 0IPSEC(key_engine): got a queue event... IPSEC(spi_response): getting spi 0xd0e27cb6(3504503990) for SA from 204.1.1.1 to 203.1.1.1 for prot 3 return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 204.1.1.1, dest 203.1.1.1 OAK_QM exchange oakley_process_quick_mode: OAK_QM_AUTH_AWAIT ISAKMP (0): Creating IPSec SAs inbound SA from 204.1.1.1 to 203.1.1.1 proxy 10.2.2.0 to 10.1.1.0) has spi 3504503990 and conn_id 4 and flags 4 lifetime of 28800 seconds lifetime of 4608000 kilobytes outbound SA from 203.1.1.1 to 204.1.1.1(proxy 10.1.1.0 to 10.2.2.0) has spi 2729504033 and conn_id 3 and flags 4 lifetime of 28800 seconds lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event... IPSEC(initialize_sas): , (key eng. msg.) dest= 203.1.1.1, src= 204.1.1.1, dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), protocol= ESP, transform= esp-des esp-md5-hmac , lifedur= 28800s and 4608000kb, spi= 0xd0e27cb6(3504503990), conn_id= 4, keysize= 0, flags= 0x4 IPSEC(initialize_sas): , (key eng. msg.) src= 203.1.1.1, dest= 204.1.1.1, src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), protocol= ESP, transform= esp-des esp-md5-hmac , lifedur= 28800s and 4608000kb, spi= 0xa2b0ed21(2729504033), conn_id= 3, keysize= 0, flags= 0x4 return status is IKMP_NO_ERROR
ISAKMP (0): beginning Main Mode exchange crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1 OAK_MM exchange ISAKMP (0): processing SA payload. message ID = 0 ISAKMP (0): Checking ISAKMP transform 1 against priority 10 policy ISAKMP: encryption DES-CBC ISAKMP: hash MD5 ISAKMP: default group 1 ISAKMP: auth pre-share ISAKMP: life type in seconds ISAKMP: life duration (basic) of 1000 ISAKMP (0): atts are acceptable. Next payload is 0 ISAKMP (0): SA is doing pre-shared key authentication using id type ID_FQDN return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1 OAK_MM exchange ISAKMP (0): processing KE payload. message ID = 0 ISAKMP (0): processing NONCE payload. message ID = 0 ISAKMP (0): processing vendor id payload ISAKMP (0): speaking to another IOS box! ISAKMP (0): ID payload next-payload : 8 type : 2 protocol : 17 port : 500 length : 18 ISAKMP (0): Total payload length: 22 return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1 OAK_MM exchange ISAKMP (0): processing ID payload. message ID = 0 ISAKMP (0): processing HASH payload. message ID = 0 ISAKMP (0): SA has been authenticated ISAKMP (0): beginning Quick Mode exchange, M-ID of 1223411072:48ebc580IPSEC(key_engine):got a queue event... IPSEC(spi_response): getting spi 0xa2b0ed21(2729504033) for SA from 203.1.1.1 to 204.1.1.1 for prot 3 return status is IKMP_NO_ERROR crypto_isakmp_process_block: src 203.1.1.1, dest 204.1.1.1 OAK_QM exchange oakley_process_quick_mode: OAK_QM_IDLE ISAKMP (0): processing SA payload. message ID = 1223411072 ISAKMP : Checking IPSec proposal 1 ISAKMP: transform 1, ESP_DES ISAKMP: attributes in transform: ISAKMP: encaps is 1 ISAKMP: SA life type in seconds ISAKMP: SA life duration (basic) of 28800 ISAKMP: SA life type in kilobytes ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0 ISAKMP: authenticator is HMAC-MD5 ISAKMP (0): atts are acceptable.IPSEC(validate_proposal_request): proposal part #1, (key eng. msg.) dest= 203.1.1.1, src= 204.1.1.1, dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), protocol= ESP, transform= esp-des esp-md5-hmac , lifedur= 0s and 0kb, spi= 0x0(0), conn_id= 0, keysize= 0, flags= 0x4 ISAKMP (0): processing NONCE payload. message ID = 1223411072 ISAKMP (0): processing ID payload. message ID = 1223411072 ISAKMP (0): processing ID payload. message ID = 1223411072 ISAKMP (0): Creating IPSec SAs inbound SA from 203.1.1.1 to 204.1.1.1 (proxy 10.1.1.0 to 10.2.2.0) has spi 2729504033 and conn_id 4 and flags 4 lifetime of 28800 seconds lifetime of 4608000 kilobytes outbound SA from 204.1.1.1 to 203.1.1.1 (proxy 10.2.2.0 to 10.1.1.0) has spi 3504503990 and conn_id 3 and flags 4 lifetime of 28800 seconds lifetime of 4608000 kilobytesIPSEC(key_engine): got a queue event... IPSEC(initialize_sas): , (key eng. msg.) dest= 204.1.1.1, src= 203.1.1.1, dest_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), src_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), protocol= ESP, transform= esp-des esp-md5-hmac , lifedur= 28800s and 4608000kb, spi= 0xa2b0ed21(2729504033), conn_id= 4, keysize= 0, flags= 0x4 IPSEC(initialize_sas): , (key eng. msg.) src= 204.1.1.1, dest= 203.1.1.1, src_proxy= 10.2.2.0/255.255.255.0/0/0 (type=4), dest_proxy= 10.1.1.0/255.255.255.0/0/0 (type=4), protocol= ESP, transform= esp-des esp-md5-hmac , lifedur= 28800s and 4608000kb, spi= 0xd0e27cb6(3504503990), conn_id= 3, keysize= 0, flags= 0x4 return status is IKMP_NO_ERROR
19 16:43:20.402 06/28/01 Sev=Info/4 CM/0x63100004 Establish secure connection using Ethernet 20 16:43:20.402 06/28/01 Sev=Info/4 CM/0x63100025 Attempt connection with server "203.1.1.1" 21 16:43:20.402 06/28/01 Sev=Info/6 IKE/0x6300003B Attempting to establish a connection with 203.1.1.1. 22 16:43:20.442 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID, VID, VID) to 203.1.1.1 23 16:43:20.452 06/28/01 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 24 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x6300002F Received ISAKMP packet: peer = 203.1.1.1 25 16:43:20.492 06/28/01 Sev=Info/4 IKE/0x63000014 RECEIVING <<< ISAKMP OAK AG (SA, VID, VID, VID, KE, ID, NON, HASH) from 203.1.1.1 26 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000059 Vendor ID payload = 12F5F28C457168A9702D9FE274CC0100 27 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000001 Peer is a Cisco-Unity compliant peer 28 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000059 Vendor ID payload = AFCAD71368A1F1C96B8696FC77570100 29 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000001 Peer supports DPD 30 16:43:20.492 06/28/01 Sev=Info/5 IKE/0x63000059 Vendor ID payload = A0EB477E6627B406AA10F958254B3517 31 16:43:20.542 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT) to 203.1.1.1 32 16:43:20.542 06/28/01 Sev=Info/4 CM/0x6310000E Established Phase 1 SA. 1 Phase 1 SA in the system 33 16:43:21.143 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.1.1.1 34 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x6300002F Received ISAKMP packet: peer = 203.1.1.1 35 16:43:24.067 06/28/01 Sev=Info/4 IKE/0x63000014 RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.1.1.1 36 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x63000010 MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.3.3.1 37 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x63000010 MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 10.1.1.3 38 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x63000010 MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NBNS(1) (a.k.a. WINS) : , value = 10.1.1.3 39 16:43:24.067 06/28/01 Sev=Info/5 IKE/0x6300000E MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = cisco.com 40 16:43:24.067 06/28/01 Sev=Info/4 CM/0x63100018 Mode Config data received 41 16:43:24.668 06/28/01 Sev=Info/5 IKE/0x63000055 Received a key request from Driver for IP address 203.1.1.1, GW IP = 203.1.1.1 42 16:43:24.668 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.1.1.1 43 16:43:24.668 06/28/01 Sev=Info/5 IKE/0x63000055 Received a key request from Driver for IP address 10.10.10.255, GW IP = 203.1.1.1 44 16:43:24.668 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.1.1.1 45 16:43:24.668 06/28/01 Sev=Info/4 IPSEC/0x63700014 Deleted all keys 46 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x6300002F Received ISAKMP packet: peer = 203.1.1.1 47 16:43:25.619 06/28/01 Sev=Info/4 IKE/0x63000014 RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from 203.1.1.1 48 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000044 RESPONDER-LIFETIME notify has value of 28800 seconds 49 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000045 RESPONDER-LIFETIME notify has value of 4608000 kb 50 16:43:25.619 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK QM *(HASH) to 203.1.1.1 51 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000058 Loading IPsec SA (Message ID = 0x59515364 OUTBOUND SPI = 0xB24CDB55 INBOUND SPI = 0x83AA0042) 52 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000025 Loaded OUTBOUND ESP SPI: 0xB24CDB55 53 16:43:25.619 06/28/01 Sev=Info/5 IKE/0x63000026 Loaded INBOUND ESP SPI: 0x83AA0042 54 16:43:25.619 06/28/01 Sev=Info/4 CM/0x63100019 One secure connection established 55 16:43:25.629 06/28/01 Sev=Info/6 DIALER/0x63300003 Connection established. 56 16:43:25.669 06/28/01 Sev=Info/6 DIALER/0x63300008 MAPI32 Information - Outlook not default mail client 57 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x6300002F Received ISAKMP packet: peer = 203.1.1.1 58 16:43:25.960 06/28/01 Sev=Info/4 IKE/0x63000014 RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from 203.1.1.1 59 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000044 RESPONDER-LIFETIME notify has value of 28800 seconds 60 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000045 RESPONDER-LIFETIME notify has value of 4608000 kb 61 16:43:25.960 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK QM *(HASH) to 203.1.1.1 62 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000058 Loading IPsec SA (Message ID = 0x23A23005 OUTBOUND SPI = 0xAD0599DB INBOUND SPI = 0x2B74D4A4) 63 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000025 Loaded OUTBOUND ESP SPI: 0xAD0599DB 64 16:43:25.960 06/28/01 Sev=Info/5 IKE/0x63000026 Loaded INBOUND ESP SPI: 0x2B74D4A4 65 16:43:25.960 06/28/01 Sev=Info/4 CM/0x63100021 Additional Phase 2 SA established. 66 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010 Created a new key structure 67 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F Added key with SPI=0x55db4cb2 into key list 68 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010 Created a new key structure 69 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F Added key with SPI=0x4200aa83 into key list 70 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010 Created a new key structure 71 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F Added key with SPI=0xdb9905ad into key list 72 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x63700010 Created a new key structure 73 16:43:25.960 06/28/01 Sev=Info/4 IPSEC/0x6370000F Added key with SPI=0xa4d4742b into key list 74 16:43:35.173 06/28/01 Sev=Info/6 IKE/0x6300003D Sending DPD request to 203.1.1.1, seq# = 1856135987 75 16:43:35.173 06/28/01 Sev=Info/4 IKE/0x63000013 SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 203.1.1.1 76 16:43:35.173 06/28/01 Sev=Info/5 IKE/0x6300002F Received ISAKMP packet: peer = 203.1.1.1 77 16:43:35.173 06/28/01 Sev=Info/4 IKE/0x63000014 RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 203.1.1.1 78 16:43:35.173 06/28/01 Sev=Info/5 IKE/0x6300003F Received DPD ACK from 203.1.1.1, seq# received = 1856135987, seq# expected = 1856135987
改定 | 発行日 | コメント |
---|---|---|
1.0 |
13-Oct-2008 |
初版 |