Ce document explique les entrées des commandes progressives qui sont nécessaires pour la mise en œuvre de la signalisation E1 R2. Ce document donne également des informations de dépannage avec des commandes de débogage.
Remarque : Avant d'utiliser ce document, il est recommandé de lire la théorie de la signalisation E1 R2 pour la première fois.
Avant de tenter cette configuration, assurez-vous de respecter les conditions requises suivantes :
La signalisation R2 s'applique uniquement à E1.
La signalisation R2 n'est pas prise en charge sur le routeur Cisco MC3810.
Pour exécuter la signalisation R2 sur les routeurs de la gamme Cisco 2600/3600, ce matériel est requis :
VWIC-1MFT-E1 ou VWIC-2MFT-E1 ou VWIC-2MFT-E1-DI avec l'un de ces modules de densité vocale : NM-HDV (High Density Voice Network Module) ou NM-HD-2VE (module de réseau voix/télécopie de communications IP à 2 emplacements ) .
Définissez la commande ds0-group (ou cas-group, basée sur la version Cisco IOS®) sur les contrôleurs E1 (AS5x00, routeurs Cisco 2600/3600).
Utilisez la commande cas-custom afin de personnaliser les variantes E1 R2 pour différents pays ou régions.
Les informations de ce document sont basées sur cette version logicielle et matérielle :
Cisco AS5300 avec le logiciel Cisco IOS Version 12.0.7T
Remarque : la signalisation E1 R2 a été introduite sur les routeurs de la gamme Cisco 2600/3600 dans les versions 12.1.2XH et 12.1(3)T du logiciel Cisco IOS.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
For more information on document conventions, refer to the Cisco Technical Tips Conventions.
Cette section présente les informations que vous pouvez utiliser pour configurer E1 R2.
Remarque : Pour obtenir des informations supplémentaires sur les commandes utilisées dans ce document, reportez-vous à l'Outil de recherche de commandes (clients enregistrés uniquement).
Avant de mettre en oeuvre la signalisation E1 R2 dans un routeur Cisco AS5300, assurez-vous que votre version du logiciel Cisco IOS est compatible avec le Cisco VCware du module E1. Afin de vérifier la compatibilité du logiciel Cisco IOS, référez-vous à la matrice de compatibilité Cisco VCWare pour le Cisco AS5300. Si les versions sont incompatibles, les modules du processeur de signal numérique (DSP) de la carte vocale ne se chargent pas et le traitement du signal vocal ne se produit pas.
Généralement, si la version de Cisco VCWare est incompatible avec le logiciel Cisco IOS, vous pouvez entrer la commande show vfc slot_number interface afin de voir ceci comme indiqué dans cet exemple.
eefje#show vfc 1 interface Rx: in ptr 18, outptr 0 Tx: in ptr 14 outptr 14 0 in hw queue, 0 queue head , 0 queue tail Hardware is VFC out-of-band channel Interface : state RESET DSP instance (0x61048284) dsp_number 0, Channel ID 0 TX outstanding 0, max TX outstanding 0 Received 18 packets, 1087 bytes, 0 giant packets 0 drops, 0 no buffers, 0 input errors 121 bytes output, 14 frames output 0 bounce errors 0 DSP module 1 is not installed DSP module 2 is not installed DSP module 3 is not installed DSP module 4 is not installed DSP module 5 is not installed
Dans le premier exemple de sortie de la commande show vfc slot_number interface, le numéro de module DSP n'est pas installé montre que les versions sont incompatibles pour ce numéro de module.
Ce deuxième jeu de résultats est un exemple des modules DSP dont la version correcte de Cisco VCWare est chargée :
eefje#show vfc 1 interface Rx: in ptr 24, outptr 0 TX: in ptr 15 outptr 15 0 in hw queue, 0 queue head , 0 queue tail Hardware is VFC out-of-band channel Interface : state RESET DSP instance (0x618C6088) dsp_number 0, Channel ID 0 TX outstanding 0, max TX outstanding 0 Received 283288 packets, 15864278 bytes, 0 giant packets 0 drops, 0 no buffers, 0 input errors 1416459 bytes output, 141647 frames output 0 bounce errors 0 Slot 1, DSPM 1 (C542), DSP 1, Channel 1 State RESET, DSP instance (0x61914BDC) TX outstanding 0, max TX outstanding 8 Received 0 packets, 0 bytes, 0 giant packets 0 drops, 0 no buffers, 0 input errors 0 bytes output, 0 frames output 0 bounce errors 0 Slot 1, DSPM 1 (C542), DSP 2, Channel 1 State RESET, DSP instance (0x6191510C) TX outstanding 0, max TX outstanding 8 Received 0 packets, 0 bytes, 0 giant packets 0 drops, 0 no buffers, 0 input errors 0 bytes output, 0 frames output 0 bounce errors 0
Afin de vérifier la version de Cisco VCWare installée, entrez la commande show vfc slot_number version vcware, comme indiqué dans cet exemple :
eefje#show vfc 1 version vcware Voice Feature Card in Slot 1: VCware Version : 4.10 ROM Monitor Version : 1.2 DSPware Version : Technology : C542
Remarque : assurez-vous que la version de la technologie Cisco VCWare (c549 ou c542) correspond à la technologie DSP VFC installée (DSPM-542 : prise en charge vocale à densité unique ou DSPM-549 : haute densité).
Complétez ces étapes afin de configurer E1 R2 :
Configurez le contrôleur E1 qui se connecte au commutateur ou autocommutateur privé (PBX).
Assurez-vous que le tramage et le codage de ligne de l'E1 sont correctement définis.
Pour le tramage E1, choisissez CRC ou non CRC.
Pour l'écrêtage de ligne E1, choisissez HDB3 ou AMI.
Pour la source de l'horloge E1, sélectionnez interne ou ligne. Gardez à l'esprit que les différents PBX ont des exigences différentes sur la source d'horloge.
Personnalisez la configuration à l'aide de la commande cas-custom.
Utilisez cette séquence de commandes afin de définir votre signalisation de ligne.
eefje(config)#controller E1 0 eefje(config-controller)#ds0-group 1 timeslots 1-15 type ? ... r2-analog R2 ITU Q411 r2-digital R2 ITU Q421 r2-pulse R2 ITU Supplement 7 ...
Il s'agit de la séquence de commandes du logiciel Cisco IOS Version 11.3.
eefje(config)#controller E1 0 eefje(config-controller)#cas-group 1 timeslot 1-15 type ? ...
Remarque : si vous effectuez une mise à niveau du logiciel Cisco IOS Version 11.3 vers 12.0, la nouvelle commande remplace automatiquement l'ancienne.
Cet exemple de séquence de commandes montre comment configurer les différents types de signalisation interregistre :
eefje(config)#controller E1 0 eefje(config-controller)#ds0-group 1 timeslots 1-15 type r2-digital ? dtmf DTMF tone signaling r2-compelled R2 Compelled Register Signaling r2-non-compelled R2 Non Compelled Register Signaling r2-semi-compelled R2 Semi Compelled Register Signaling
La prise en charge DNIS (Dialed Number Identification Service) est activée par défaut dans la mise en oeuvre de R2 par Cisco. Si vous activez l'option d'identification automatique de numéro (ANI), la collecte des informations DNIS est toujours effectuée. La spécification de l'option ANI ne désactive pas la collection DNIS. DNIS est le numéro appelé. ANI est le numéro de l'appelant. Par exemple, si vous configurez un routeur appelé A pour appeler un routeur appelé B, le numéro DNIS est attribué au routeur B et le numéro ANI au routeur A. ANI est similaire à l'ID de l'appelant.
Les sous-commandes sous la commande cas-custom sont utilisées afin de prendre en charge les variantes de pays. Ils sont également utilisés afin de personnaliser les paramètres de signalisation associée au canal (CAS). Cette séquence de commandes illustre comment afficher toutes les options de commande cas-custom.
eefje(config)#controller E1 0 eefje(config-controller)#cas-custom 1 eefje(config-ctrl-cas)#? CAS custom commands: ani-digits Expected number of ANI digits ani-timeout Timeout for ANI digits answer-guard-time Wait Between Group-B Answer Signal And Line Answer answer-signal Answer signal to be used caller-digits Digits to be collected before requesting CallerID category Category signal country Country Name debounce-time Debounce Timer default Set a command to its defaults dnis-complete Send I-15 after DNIS digits for dial-out dnis-digits Expected number of DNIS digits exit Exit from cas custom mode groupa-callerid-end Send Group-A Caller ID End invert-abcd invert the ABCD bits before TX and after rx ka kA Signal kd KD Signal metering R2 network is sending metering signal nc-congestion Non Compelled Congestion signal no Negate a command or set its defaults proceed-to-send Suppress proceed-to-send signal for pulsed line signaling release-ack Send Release Acknowledgment to Clear Forward release-guard-time Release Guard Timer request-category DNIS Digits to be collected before requesting category seizure-ack-time Seizure to Acknowledge timer unused-abcd Unused ABCD bit values
Pour plus d'informations sur les paramètres de la commande cas-custom, référez-vous à Personnalisation de E1 R2 avec la commande cas-custom.
Ce document utilise cette configuration du réseau.
Pour les besoins de ce document, voici les trois configurations différentes de R2 qui sont affichées sur l'interface E1 :
Les configurations ont été modifiées afin de n'afficher que les informations discutées dans ce document.
eefje configuré pour R2 Digital Non-Obligated |
---|
hostname eefje ! controller E1 0 clock source line primary dso-group 1 timeslots 1-15 type r2-digital r2-non-compelled cas-custom 1 !--- For more information on these commands !--- refer to ds0-group and cas-custom. ! voice-port 0:1 cptone BE !--- The cptone command is country specific. For more !--- information on this command, refer to cptone . ! dial-peer voice 123 pots destination-pattern 123 direct-inward-dial port 0:1 prefix 123 ! dial-peer voice 567 voip destination-pattern 567 session target ipv4:2.0.0.2 ! |
eefje configuré pour R2 Digital Semi-Compellé |
---|
hostname eefje ! controller E1 0 clock source line primary ds0-group 1 timeslots 1-15 type r2-digital r2-semi-compelled cas-custom 1 !--- For more information on these commands !--- refer to ds0-group and cas-custom . ! voice-port 0:1 cptone BE !--- The cptone command is country specific. For more !--- information on this command, refer to cptone . dial-peer voice 123 pots destination-pattern 123 direct-inward-dial port 0:1 prefix 123 ! dial-peer voice 567 voip destination-pattern 567 session target ipv4:2.0.0.2 ! |
eefje configuré pour l'ANI numérique obligatoire de R2 |
---|
hostname eefje ! controller E1 0 clock source line primary ds0-group 1 timeslots 1-15 type r2-digital r2-compelled ani cas-custom 1 !--- For more information on these commands !--- refer to ds0-group and cas-custom . voice-port 0:1 cptone BE !--- The cptone command is country specific. For more !--- information on this command, refer to cptone . dial-peer voice 123 pots destination-pattern 123 direct-inward-dial port 0:1 prefix 123 ! dial-peer voice 567 voip destination-pattern 567 session target ipv4:2.0.0.2 ! |
Aucune procédure de vérification n'est disponible pour cette configuration.
Cette section fournit des informations que vous pouvez utiliser pour dépanner votre configuration.
Il s’agit des informations de dépannage relatives à cette configuration. Suivez ces instructions afin de faire le dépannage de votre configuration .
Vérifiez que le contrôleur E1 0 est actif.
En cas de panne, vérifiez le tramage, le codage de ligne, la source de l'horloge, les alarmes, remplacez le câble, réinstallez la carte, etc. Utilisez le document Personnalisation de R2 E1 avec la commande cas-custom comme référence.
Si vous utilisez un AS5300, vérifiez que les DSP sont correctement installés avec la commande show vfc slot number interface.
Configurez la numérotation directe à l'arrivée (DID) sur l'homologue POTS (plain old phone service), de sorte que les chiffres reçus soient utilisés pour choisir un homologue sortant.
Spécifiez cptone (cptone est spécifique à votre pays) sur les ports vocaux.
Une commande cptonecountry doit être configurée afin de correspondre à la commande cas-custom country. Le paramètre cptone définit les tonalités de progression de l'appel pour un pays particulier, et plus important encore, définit le codage sur a-law ou u-law, qui dépend du pays. Le codage par défaut pour les États-Unis est u-law.
Associez les dispositions de signalisation de ligne et d’enregistrement à la configuration du commutateur.
Activez certains des débogages présentés dans ce document et étudiez les résultats.
Vérifiez la communication entre le routeur et le PBX ou le commutateur :
La ligne est-elle saisie ?
Le routeur reçoit-il/envoie-t-il des chiffres ?
Déterminez quel côté efface l'appel.
Si possible, utilisez les dernières versions du logiciel Cisco IOS disponibles sur Cisco.com.
Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.
Remarque : Avant d'émettre des commandes debug, reportez-vous aux Informations importantes sur les commandes de débogage.
Remarque : Pour le logiciel Cisco IOS Version 12.0, utilisez ces débogages :
debug cas - Pour la signalisation de ligne.
debug csm voice - Pour la signalisation interregister.
debug vtsp all - Afin que la sortie de tous les messages (chiffres) échangés entre le PBX et le routeur.
Pour la version du logiciel Cisco IOS IOS 11.3, utilisez les commandes suivantes :
modem-mgmt csm debug-rbs - Pour la signalisation de ligne (vous devez d'abord spécifier le service interne en mode de configuration.)
debug csm voice - Pour la signalisation interregister.
debug vtsp all - Afin que la sortie de tous les messages (chiffres) échangés entre le PBX et le routeur.
Pour les plates-formes AS5400 et AS5350, utilisez les débogages suivants :
debug sigsm r2 - Pour la signalisation inter-register
debug vtsp all - Afin que la sortie de tous les messages (chiffres) échangés entre le PBX et le routeur.
Comme il existe trois configurations différentes précédemment illustrées dans ce document, voici trois débogages différents :
Afin de mieux comprendre cette sortie de débogage, référez-vous à Théorie de signalisation E1 R2.
eefje#show debug CAS: Channel Associated Signaling debugging is on CSM Voice: Voice Call Switching Module debugging is on Voice Telephony session debugging is on Voice Telephony dsp debugging is on Voice Telephony error debugging is on eefje# eefje# eefje# Jan 6 10:41:28.677: from NEAT(0): (0/0): Rx SEIZURE (ABCD=0001) Jan 6 10:41:28.717: VDEV_ALLOCATE: failed to allocate a device Jan 6 10:41:28.717: VDEV_ALLOCATE: 1/28 is allocated Jan 6 10:41:28.721: csm_vtsp_init_tdm (voice_vdev=0x620BF874) Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2, dspm 1, dsp 5, dsp_channel 1 Jan 6 10:41:28.721: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5, channel 3, bank 1, bp_channel 4, BP_stream 255 Jan 6 10:41:28.721: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0018): EVENT_CALL_DIAL_IN at slot 2 and port 16 Jan 6 10:41:28.721: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 2, port 16 Jan 6 10:41:28.721: csm_vtsp_start_digit_collect (voice_vdev=0x620BF874) Jan 6 10:41:28.721: Enter csm_connect_pri_vdev function Jan 6 10:41:28.721: csm_connect_pri_vdev:tdm_allocate_BP_ts()call. BP TS allocated at BP_stream0, BP_Ch28,vdev_common 0x6 20BF8E4 Jan 6 10:41:28.721: to NEAT:(cid0018) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan0 Jan 6 10:41:28.721: vtsp_do_call_setup_ind Jan 6 10:41:28.721: vtsp_do_call_setup_ind: Call ID=65681, guid=61FAF610 Jan 6 10:41:28.721: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0, id1=0, id2=0, calling=, called= Jan 6 10:41:28.721: vtsp_do_call_setup_ind: redirect DN = reason = 0vtsp_open_voice_and_set_params Jan 6 10:41:28.721: dsp_close_voice_channel: [0:1:0] packet_len=8 channel_id =8529 packet_id=75 Jan 6 10:41:28.721: dsp_open_voice_channel_20: [0:1:0] packet_Len=16 channel_id =8529 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0 serial_port=0 Jan 6 10:41:28.721: dsp_encap_config_20: [0:1:0] packet_Len=24 channel_id=8529 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 6 10:41:28.721: dsp_set_playout: [0:1:0] packet_Len=18 channel_id=8529 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 Jan 6 10:41:28.721: dsp_echo_canceller_control: [0:1:0] packet_Len=10 channel_id=8529 packet_id=66 flags=0x0 Jan 6 10:41:28.721: dsp_set_gains: [0:1:0] packet_Len=12 channel_id=8529 packet_id=91 in_gain=0 out_gain=0 Jan 6 10:41:28.721: dsp_vad_enable: [0:1:0] packet_Len=10 channel_id=8529 packet_id=78 thresh=-38 Jan 6 10:41:28.721: dsp_voice_mode: [0:1:0] packet_Len=24 channel_id=8529 packet_id=73 coding_type=1 voice_field_size=80 V AD_flag=0 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0vtsp_do_r2_start_digit(): dsp_dtmf_mode() dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE) Jan 6 10:41:28.725: dsp_dtmf_mode: [0:1:0] packet_Len=10 channel_id=8529 packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit():fsm_push(vtsp_r2_state_table) Jan 6 10:41:28.725: csm_vtsp_call_setup_resp (vdev_info=0x620BF874, vtsp_cdb=0x621C5F3C) Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat BP_stream0,BP_Ch28 Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:dst_tdm_chnl call. BP TS allocatedat stream 5, chan 3,BP_stream 255, BP_ch 4 Jan 6 10:41:28.725: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 3,BP_stream 0, BP_ch 28 Jan 6 10:41:28.725: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK (DNIS=, ANI=) at slot 2, port 16 Jan 6 10:41:28.725: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_IDLE R2 Got Event R2_START Jan 6 10:41:28.821: CSM_RX_CAS_EVENT_FROM_NEAT:(0018):EVENT_START_RX_TONE at slot 2 and port 16 Jan 6 10:41:28.821: from NEAT(0): (0/0): TX SEIZURE_ACK (ABCD=1101) !--- Digit 5 is sent: Forward Signal Group I-5. Jan 6 10:41:29.233: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=5, rtp_timestamp=0x0CA95D43 dc_digit_up Jan 6 10:41:29.233: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5) Jan 6 10:41:29.233: CSM voice (2/16): Rcvd Digit detected(5) Jan 6 10:41:29.233: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event 5 Jan 6 10:41:29.365: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5, duration=8321dc_digit Jan 6 10:41:29.365: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5) Jan 6 10:41:29.365: CSM voice (2/16): Rcvd Digit detected(5) Jan 6 10:41:29.365: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF !--- Digit 6 is sent: Forward Signal Group I-6. Jan 6 10:41:29.593: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=6, rtp_timestamp=0x0CA95D43 dc_digit_up Jan 6 10:41:29.593: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (6) Jan 6 10:41:29.593: CSM voice (2/16): Rcvd Digit detected(6) Jan 6 10:41:29.593: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event 6 Jan 6 10:41:29.725: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6, duration=8321dc_digit Jan 6 10:41:29.725: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6) Jan 6 10:41:29.725: CSM voice (2/16): Rcvd Digit detected(6) Jan 6 10:41:29.725: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF !--- Digit 7 is sent: Forward Signal Group I-7. Jan 6 10:41:29.953: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=7, rtp_timestamp=0x0CA95D43 dc_digit_up Jan 6 10:41:29.953: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (7) Jan 6 10:41:29.953: CSM voice (2/16): Rcvd Digit detected(7) Jan 6 10:41:29.953: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE:R2_IN_COLLECT_DNIS R2 Got Event 7 Jan 6 10:41:30.085: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7, duration=8321dc_digit Jan 6 10:41:30.085: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (7) Jan 6 10:41:30.085: CSM voice (2/16): Rcvd Digit detected(7) Jan 6 10:41:30.085: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF !--- Timeout: 3 seconds (default timer - AS5300 assumes DNIS is finished). Jan 6 10:41:32.953: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_TIMER !--- Send digit 6: Backward Signal Group B-6 (subscriber's line free-charge). Jan 6 10:41:32.953: vtsp_r2_generate_digits: vdev_common=0x620BF8E4, string=567dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6# Jan 6 10:41:32.953: dsp_dtmf_dialing: [0:1:0] packet_Len=36 channel_id=8529 packet_id=90 string=6# digits=2, time_on=150, time_off=30 Jan 6 10:41:32.953:& digit=e, components=2, freq_of_first=900, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 6 10:41:32.953: digit=o, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 Jan 6 10:41:33.313: vtsp_process_dsp_message: MSG_TX_DIALING_DONE dc_dialing_done() Jan 6 10:41:33.313: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE:R2_IN_ANSWER_PULSE R2 Got Event R2_DIGITS_GENR2_ALERTING Jan 6 10:41:34.313: R2 Incoming Voice(2/16): DSX (E1 0:0): STATE: R2_IN_ANSWER_PULSE R2 Got Event R2_TONE_TIMER Jan 6 10:41:34.313: R2_IN_IDLE:2 r2_in_connect called Jan 6 10:41:34.313: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_ADDR_INFO_COLLECTED (DNIS=567, ANI=) at slot 2, port 16 Jan 6 10:41:34.313: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0, calling_number= called_number=567): peer_tag=0 Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 6 10:41:34.313: VDEV_ALLOCATE: failed to allocate a device Jan 6 10:41:34.313: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 6 10:41:34.313: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2, port 16 Jan 6 10:41:34.313: vtsp_ic_switch : (voice_vdev= 0x620BF874) Jan 6 10:41:34.313: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C, tsp_info=0x620BF874, calling_number= called_number=567 redir ect_number=): peer_tag=123dc_switch: fsm_pop() Jan 6 10:41:34.313: vtsp_do_call_setup_ind Jan 6 10:41:34.313: vtsp_do_call_setup_ind: Call ID=65683, guid=61FAF610 Jan 6 10:41:34.313: vtsp_do_call_setup_ind: type=0, under_spec=0, name=ab^Lx, id0=1, id1=0, id2=0, calling=123, called=567 Jan 6 10:41:34.317: dsp_cp_tone_off: [] packet_Len=8 channel_id=8529 packet_id=71 Jan 6 10:41:34.317: dsp_idle_mode: [] packet_Len=8 channel_id=8529 packet_id=68 Jan 6 10:41:34.317: dsp_close_voice_channel: [] packet_Len=8 channel_id=8529 packet_id=75 Jan 6 10:41:34.317: vtsp_timer_stop: 67475758 Jan 6 10:41:34.317: csm_vtsp_call_setup_resp (vdev_info=0x620BF874, vtsp_cdb=0x621C5F3C) Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat BP_stream0, BP_Ch28 Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 3,BP_stream 0, BP_ch 28 Jan 6 10:41:34.317: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 3,BP_stream 0, BP_ch 28vt sp_open_voice_and_set_params Jan 6 10:41:34.317: dsp_close_voice_channel: [0:1 (54)] packet_Len=8 channel_id=8529 packet_id=75 Jan 6 10:41:34.317: dsp_open_voice_channel_20: [0:1 (54)] packet_Len=16 channel_id=8529 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0 serial_port=0 Jan 6 10:41:34.317: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 6 10:41:34.317: dsp_set_playout: [0:1 (54)] packet_Len=18 channel_id=8529 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 Jan 6 10:41:34.317: dsp_echo_canceller_control: [0:1 (54)] packet_Len=10 channel_id=8529 packet_id=66 flags=0x0 Jan 6 10:41:34.317: dsp_set_gains: [0:1 (54)] packet_Len=12 channel_id=8529 packet_id=91 in_gain=0 out_gain=0 Jan 6 10:41:34.317: dsp_vad_enable: [0:1 (54)] packet_Len=10 channel_id=8529 packet_id=78 thresh=-38act_proceeding Jan 6 10:41:34.321: csm_vtsp_call_proceeding:DST_tdm_chnl call. BP TS allocatedstream 5, chan 3,BP_stream 0, BP_ch 28act_alert Jan 6 10:41:34.345: vtsp_ring_noan_timer_start: 67475761 Jan 6 10:41:34.345: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C)act_bridge act_caps_ind Jan 6 10:41:34.589: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20, FaxRate 2, FaxBytes 20 SignalType 0 DtmfRelay 1, Modem 1act_caps_ack Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8 channel_id=8529 packet_id=68 Jan 6 10:41:34.589: act_caps_ack: codec = 15, ret = 1 Jan 6 10:41:34.589: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529 packet_id=71 Jan 6 10:41:34.589: dsp_idle_mode: [0:1 (54)] packet_Len=8 channel_id=8529 packet_id=68 Jan 6 10:41:34.589: dsp_encap_config_20: [0:1 (54)] packet_Len=24 channel_id=8529 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 6 10:41:34.589: dsp_voice_mode: [0:1 (54)] packet_Len=24 channel_id=8529 packet_id=73 coding_type=20 voice_field_size=20 VAD_flag=1 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect Jan 6 10:41:36.857: vtsp_ring_noan_timer_stop: 67476012 Jan 6 10:41:36.857: dsp_cp_tone_off: [0:1 (54)] packet_Len=8 channel_id=8529 packet_id=71 Jan 6 10:41:36.857: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C, voice_vdev=0x620BF874) Jan 6 10:41:36.857: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK at slot 2, port 16 Jan 6 10:41:36.917: CSM_RX_CAS_EVENT_FROM_NEAT:(0018): EVENT_CHANNEL_CONNECTED at slot 2 and port 16 Jan 6 10:41:36.917: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED at slot 2, port 16 Jan 6 10:41:36.921: from NEAT(0): (0/0): TX ANSWERED(ABCD=0101) eefje#
Afin de mieux comprendre cette sortie de débogage, référez-vous à Théorie de signalisation E1 R2.
eefje#show debug CAS: Channel Associated Signaling debugging is on CSM Voice: Voice Call Switching Module debugging is on Voice Telephony session debugging is on Voice Telephony dsp debugging is on Voice Telephony error debugging is on eefje# eefje# eefje# Jan 6 09:53:42.389: from NEAT(0): (0/2): Rx SEIZURE(ABCD=0001) Jan 6 09:53:42.433: VDEV_ALLOCATE: failed to allocate a device Jan 6 09:53:42.433: VDEV_ALLOCATE: 1/27 is allocated Jan 6 09:53:42.433: csm_vtsp_init_tdm (voice_vdev=0x620BF320) Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 2, dspm 1, dsp 4, dsp_channel 4 Jan 6 09:53:42.433: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 7, channel 0, bank 4, BP_channel 3, BP_stream 255 Jan 6 09:53:42.433: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0017): EVENT_CALL_DIAL_IN at slot 2 and port 15 Jan 6 09:53:42.433: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 2, port 15 Jan 6 09:53:42.433: csm_vtsp_start_digit_collect (voice_vdev=0x620BF320) Jan 6 09:53:42.433: Enter csm_connect_pri_vdev function Jan 6 09:53:42.433: csm_connect_pri_vdev:tdm_allocate_BP_Ts()call. BP TS allocated at BP_stream0, BP_Ch27,vdev_common 0x6 20BF390 Jan 6 09:53:42.433: to NEAT:(cid0017) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan2 Jan 6 09:53:42.433: vtsp_do_call_setup_ind Jan 6 09:53:42.433: vtsp_do_call_setup_ind: Call ID=65675, guid=61FAF610 Jan 6 09:53:42.433: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0, id1=0, id2=0, calling=, called= Jan 6 09:53:42.433: vtsp_do_call_setup_ind: redirect DN = reason = 0vtsp_open_voice_and_set_params Jan 6 09:53:42.433: dsp_close_voice_channel: [0:1:2] packet_Len=8 channel_id=8516 packet_id=75 Jan 6 09:53:42.433: dsp_open_voice_channel_20: [0:1:2] packet_Len=16 channel_id=8516 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=1 serial_port=1 Jan 6 09:53:42.433: dsp_encap_config_20: [0:1:2] packet_Len=24 channel_id=8516 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 6 09:53:42.433: dsp_set_playout: [0:1:2] packet_Len=18 channel_id=8516 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 Jan 6 09:53:42.433: dsp_echo_canceller_control: [0:1:2] packet_Len=10 channel_id=8516 packet_id=66 flags=0x0 Jan 6 09:53:42.437: dsp_set_gains:[0:1:2] packet_Len=12 channel_id=8516 packet_id=91 in_gain=0 out_gain=0 Jan 6 09:53:42.437: dsp_vad_enable: [0:1:2] packet_Len=10 channel_id=8516 packet_id=78 thresh=-38 Jan 6 09:53:42.437: dsp_voice_mode: [0:1:2] packet_Len=24 channel_id=8516 packet_id=73 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0vtsp_do_r2_start_digit(): dsp_dtmf_mode() dsp_dtmf_mode(VTSP_TONE_R2_MF_FORWARD_MODE) Jan 6 09:53:42.437: dsp_dtmf_mode: [0:1:2] packet_Len=10 channel_id=8516 packet_id=65 dtmf_or_mf=1vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table) Jan 6 09:53:42.437: csm_vtsp_call_setup_resp (vdev_info=0x620BF320, vtsp_cdb=0x621C5F3C) Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat BP_stream0, BP_Ch27 Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 7, chan 0,BP_stream 255, BP_ch 3 Jan 6 09:53:42.437: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 7, chan 0,BP_stream 0, BP_ch 27 Jan 6 09:53:42.437: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK (DNIS=, ANI=) at slot 2, port 15 Jan 6 09:53:42.437: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_IDLE R2 Got Event R2_START Jan 6 09:53:42.533: CSM_RX_CAS_EVENT_FROM_NEAT:(0017):EVENT_START_RX_TONE at slot 2 and port 15 Jan 6 09:53:42.533: from NEAT(0): (0/2): TX SEIZURE_ACK (ABCD=1101) !--- Digit 5 is sent: Forward Signal Group I-5. Jan 6 09:53:42.641: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=5, rtp_timestamp=0x9330B42B dc_digit_up Jan 6 09:53:42.641: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (5) Jan 6 09:53:42.641: CSM voice (2/15): Rcvd Digit detected(5) Jan 6 09:53:42.641: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event 5 !--- Digit 1 sent (pulse): Backward Signal Group A-1 (Send next digit) !--- "#" this indicates that it is a pulse). Jan 6 09:53:42.641: vtsp_r2_generate_digits: vdev_common=0x620BF390, string=5dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1# Jan 6 09:53:42.641: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516 packet_id=90 string=1# digits=2, time_on=150, time_off=30 Jan 6 09:53:42.641: digit=`, components=2, freq_of_first=1020, freq_of_second=1140, amp_of_first=8192, amp_of_second=8192 Jan 6 09:53:42.641: digit=o, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 Jan 6 09:53:42.741: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=5, duration=8291dc_digit Jan 6 09:53:42.741: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (5) Jan 6 09:53:42.741: CSM voice (2/15): Rcvd Digit detected(5) Jan 6 09:53:42.741: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF !--- Digit 6 is sent: Forward Signal Group I. Jan 6 09:53:42.881: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=6, rtp_timestamp=0x9330B42B dc_digit_up Jan 6 09:53:42.881: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (6) Jan 6 09:53:42.881: CSM voice (2/15): Rcvd Digit detected(6) Jan 6 09:53:42.881: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event 6 !--- Digit 1 sent (pulse): Backward Signal Group A-1. (Send next digit.) Jan 6 09:53:42.881: vtsp_r2_generate_digits: vdev_common=0x620BF390, string=56dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1# Jan 6 09:53:42.881: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516 packet_id=90 string=1# digits=2, time_on=150, time_off=30 Jan 6 09:53:42.881: digit=`, components=2, freq_of_first=1020, freq_of_second=1140, amp_of_first=8192, amp_of_second=8192 Jan 6 09:53:42.881: digit=o, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 Jan 6 09:53:42.981: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=6, duration=8291dc_digit Jan 6 09:53:42.981: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (6) Jan 6 09:53:42.981: CSM voice (2/15): Rcvd Digit detected(6) Jan 6 09:53:42.981: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF !--- Digit 7 is sent: Forward Signal Group I-7. Jan 6 09:53:43.121: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=7, rtp_timestamp=0x9330B42B dc_digit_up Jan 6 09:53:43.121: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C)received digit (7) Jan 6 09:53:43.121: CSM voice (2/15): Rcvd Digit detected(7) Jan 6 09:53:43.121: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event 7 !--- Send digit 1 (pulse): Backward Signal Group A-1. Jan 6 09:53:43.121: vtsp_r2_generate_digits: vdev_common=0x620BF390, string=567dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1# Jan 6 09:53:43.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516 packet_id=90 string=1# digits=2, time_on=150, time_off=30 Jan 6 09:53:43.121: digit=`, components=2, freq_of_first=1020, freq_of_second=1140, amp_of_first=8192, amp_of_second=8192 Jan 6 09:53:43.121: digit=o, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 Jan 6 09:53:43.221: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7, duration=8291dc_digit Jan 6 09:53:43.221: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C) received digit (7) Jan 6 09:53:43.221: CSM voice (2/15): Rcvd Digit detected(7) Jan 6 09:53:43.221: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF Jan 6 09:53:43.489: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done() !--- Timeout is 3 seconds. Jan 6 09:53:46.121: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_TIMER !--- Digit 3 sent(pulse): Backward Signal Group A-3. !--- (Address-complete, changeover to reception of Group-B signals). Jan 6 09:53:46.121: vtsp_r2_generate_digits: vdev_common=0x620BF390, string=567dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3# Jan 6 09:53:46.121: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516 packet_id=90 string=3# digits=2, time_on=150, time_off=30 Jan 6 09:53:46.121: digit=b, components=2, freq_of_first=1020, freq_of_second=900, amp_of_first=8192, amp_of_second=8192 Jan 6 09:53:46.121: digit=o, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Digit 1 is sent: Forward Signal Group II-1 !--- (subscriber without priority). Jan 6 09:53:46.361: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1, rtp_timestamp=0x9330B42B dc_digit_up Jan 6 09:53:46.361: csm_vtsp_digit_ready_up (vtsp_cdb=0x621C5F3C) received digit (1) Jan 6 09:53:46.361: CSM voice (2/15): Rcvd Digit detected(1) Jan 6 09:53:46.361: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_CATEGORY R2 Got Event 1 Jan 6 09:53:46.361: r2_comp_category:R2_ALERTING !--- Digit 6 sent (pulse): Backward Signal Group B-6 !--- (the subscriber line free of charge). Jan 6 09:53:46.361: vtsp_r2_generate_digits: vdev_common=0x620BF390, string=567dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 6# Jan 6 09:53:46.361: dsp_dtmf_dialing: [0:1:2] packet_Len=36 channel_id=8516 packet_id=90 string=6# digits=2, time_on=150, time_off=30 Jan 6 09:53:46.361: digit=e, components=2, freq_of_first=900, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 6 09:53:46.361: digit=o, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 Jan 6 09:53:46.461: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=1, duration=8291dc_digit Jan 6 09:53:46.461: csm_vtsp_digit_ready (vtsp_cdb=0x621C5F3C)received digit (1) Jan 6 09:53:46.461: CSM voice (2/15): Rcvd Digit detected(1) Jan 6 09:53:46.461: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_COMPLETE R2 Got Event R2_TONE_OFF Jan 6 09:53:46.729: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done() Jan 6 09:53:47.461: R2 Incoming Voice(2/15): DSX (E1 0:2): STATE:R2_IN_WAIT_GUARD R2 Got Event R2_TONE_TIMER Jan 6 09:53:47.461: R2_IN_IDLE:2 r2_in_connect called Jan 6 09:53:47.461: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_ADDR_INFO_COLLECTED (DNIS=567, ANI=) at slot 2, port 15 Jan 6 09:53:47.461: vtsp_tsp_call_accept_check (sdb=0x61B8F0E0,calling_number= called_number=567): peer_tag=0 Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 6 09:53:47.461: VDEV_ALLOCATE: failed to allocate a device Jan 6 09:53:47.461: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 6 09:53:47.461: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 2, port 15 Jan 6 09:53:47.461: vtsp_IC_switch : (voice_vdev= 0x620BF320) Jan 6 09:53:47.461: vtsp_tsp_call_switch_ind (cdb=0x621C5F3C,tsp_info=0x620BF320, calling_number= called_number=567 redirect_number=): peer_tag=123dc_switch: fsm_pop() Jan 6 09:53:47.461: vtsp_do_call_setup_ind Jan 6 09:53:47.461: vtsp_do_call_setup_ind: Call ID=65677, guid=61FAF610 Jan 6 09:53:47.461: vtsp_do_call_setup_ind: type=0, under_spec=0, name=AB^Lo, id0=3, id1=0, id2=0, calling=123, called=567 Jan 6 09:53:47.465: dsp_cp_tone_off: [] packet_Len=8 channel_id=8516 packet_id=71 Jan 6 09:53:47.465: dsp_idle_mode: [] packet_Len=8 channel_id=8516 packet_id=68 Jan 6 09:53:47.465: dsp_close_voice_channel: [] packet_Len=8 channel_id=8516 packet_id=75 Jan 6 09:53:47.465: vtsp_timer_stop: 67189073 Jan 6 09:53:47.465: csm_vtsp_call_setup_resp (vdev_info=0x620BF320, vtsp_cdb=0x621C5F3C) Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat BP_stream0, BP_Ch27 Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 7, chan 0,BP_stream 0, BP_ch 27 Jan 6 09:53:47.465: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 7, chan 0,BP_stream 0, BP_ch 27vtsp_open_voice_and_set_params Jan 6 09:53:47.465: dsp_close_voice_channel: [0:1 (52)] packet_Len=8 channel_id=8516 packet_id=75 Jan 6 09:53:47.465: dsp_open_voice_channel_20: [0:1 (52)] packet_Len=16 channel_id=8516 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=1 serial_port=1 Jan 6 09:53:47.465: dsp_encap_config_20: [0:1 (52)] packet_Len=24 channel_id=8516 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 6 09:53:47.465: dsp_set_playout: [0:1 (52)] packet_Len=18 channel_id=8516 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 Jan& 6 09:53:47.465: dsp_echo_canceller_control: [0:1 (52)] packet_Len=10 channel_id=8516 packet_id=66 flags=0x0 Jan 6 09:53:47.465: dsp_set_gains: [0:1 (52)] packet_Len=12 channel_id=8516 packet_id=91 in_gain=0 out_gain=0 Jan 6 09:53:47.465: dsp_vad_enable: [0:1 (52)] packet_Len=10 channel_id=8516 packet_id=78 thresh=-38act_proceeding Jan 6 09:53:47.469: csm_vtsp_call_proceeding:DST_tdm_chnl call. BP TS allocatedstream 7, chan 0,BP_stream 0, BP_ch 27act_alert Jan 6 09:53:47.493: vtsp_ring_noan_timer_start: 67189076 Jan 6 09:53:47.493: csm_vtsp_call_alert (vtsp_cdb=0x621C5F3C) act_bridge act_caps_ind Jan 6 09:53:47.737: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20, FaxRate 2, FaxBytes 20 SignalType 0 DtmfRelay 1, Modem 1act_caps_ack Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516 packet_id=68 Jan 6 09:53:47.737: act_caps_ack: codec = 15, ret = 1 Jan 6 09:53:47.737: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516 packet_id=71 Jan 6 09:53:47.737: dsp_idle_mode: [0:1 (52)] packet_Len=8 channel_id=8516 packet_id=68 Jan 6 09:53:47.737: dsp_encap_config_20: [0:1 (52)] packet_Len=24 channel_id=8516 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 6 09:53:47.737: dsp_voice_mode: [0:1 (52)] packet_Len=24 channel_id=8516 packet_id=73 coding_type=20 voice_field_size= 20 VAD_flag=1 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect Jan 6 09:53:49.461: vtsp_ring_noan_timer_stop: 67189273 Jan 6 09:53:49.461: dsp_cp_tone_off: [0:1 (52)] packet_Len=8 channel_id=8516 packet_id=71 Jan 6 09:53:49.461: csm_vtsp_call_connect (vtsp_cdb=0x621C5F3C, voice_vdev=0x620BF320) Jan 6 09:53:49.461: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK at slot 2, port 15 Jan 6 09:53:49.617: CSM_RX_CAS_EVENT_FROM_NEAT:(0017): EVENT_CHANNEL_CONNECTED at slot 2 and port 15 Jan 6 09:53:49.617: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED at slot 2, port 15 Jan 6 09:53:49.621: from NEAT(0): (0/2): TX ANSWERED(ABCD=0101) eefje# eefje#
Afin de mieux comprendre cette sortie de débogage, référez-vous à Théorie de signalisation E1 R2.
eefje#debug csm voice Voice Call Switching Module debugging is on eefje#debug cas Channel Associated Signaling debugging is on Jan 7 10:00:02.907: from NEAT(0): debug-cas is on Jan 7 10:00:02.907: from NEAT(0): special debug-cas is offg vtsp all Voice telephony call control all debugging is on eefje# eefje# Jan 7 10:00:23.883: from NEAT(0): (0/8): Rx SEIZURE (ABCD=0001) Jan 7 10:00:23.927: VDEV_ALLOCATE: failed to allocate a device Jan 7 10:00:23.927: VDEV_ALLOCATE: 1/2 is allocated Jan 7 10:00:23.927: csm_vtsp_init_tdm (voice_vdev=0x61F19688) Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm slot 1, dspm 3, dsp 4, dsp_channel 1 Jan 7 10:00:23.927: csm_vtsp_init_tdm: dsprm_tdm_allocate: tdm stream 5, channel 13, bank 0, BP_channel 15, BP_stream 255 Jan 7 10:00:23.927: CSM_RX_CAS_EVENT_FROM_NEAT:(cid0007): EVENT_CALL_DIAL_IN at slot 1 and port 60 Jan 7 10:00:23.927: CSM_PROC_IDLE: CSM_EVENT_START_DIGIT_COLLECT at slot 1, port 60 Jan 7 10:00:23.927: csm_vtsp_start_digit_collect (voice_vdev=0x61F19688) Jan 7 10:00:23.927: Enter csm_connect_pri_vdev function Jan 7 10:00:23.927: csm_connect_pri_vdev:tdm_allocate_BP_Ts() call. BP TS allocated at BP_stream0, BP_Ch8,vdev_common 0x6205E5F8 Jan 7 10:00:23.927: to NEAT:(cid0007) EVENT_CHANNEL_LOCK for slot0 ctlr0 chan8 Jan 7 10:00:23.927: vtsp_do_call_setup_ind Jan 7 10:00:23.927: vtsp_do_call_setup_ind: Call ID=65579, guid=62031A88 Jan 7 10:00:23.927: vtsp_do_call_setup_ind: type=0, under_spec=0, name=, id0=0, id1=0,id2=0, calling=, called= Jan 7 10:00:23.927: vtsp_do_call_setup_ind: redirect DN = reason = 0vtsp_do_r2_start_digit(): fsm_push(vtsp_r2_state_table) Jan 7 10:00:23.927: csm_vtsp_call_setup_resp (vdev_info=0x61F19688, vtsp_cdb=0x61B5BFF8) Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat BP_stream0, BP_Ch8 Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 13,BP_stream 255, BP_ch 15 Jan 7 10:00:23.927: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 8 Jan 7 10:00:23.927: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_MODEM_OFFHOOK (DNIS=, ANI=) at slot 1, port 60 Jan 7 10:00:23.931: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_IDLE R2 Got Event R2_START Jan 7 10:00:24.027: CSM_RX_CAS_EVENT_FROM_NEAT:(0007): EVENT_START_RX_TONE at slot 1 and port 60 Jan 7 10:00:24.027: from NEAT(0): (0/8): TX SEIZURE_ACK (ABCD=1101)dc_init_dsp vtsp_open_voice_and_set_params Jan 7 10:00:24.151: dsp_close_voice_channel: [0:1:8] packet_Len=8 channel_id=4929 packet_id=75 Jan 7 10:00:24.151: dsp_open_voice_channel_20: [0:1:8] packet_Len=16 channel_id=4929 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0 serial_port=0 Jan 7 10:00:24.151: dsp_encap_config_20: [0:1:8] packet_Len=24 channel_id=4929 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 7 10:00:24.151: dsp_set_playout: [0:1:8] packet_Len=18 channel_id=4929 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 Jan 7 10:00:24.151: dsp_echo_canceller_control: [0:1:8] packet_Len=10 channel_id=4929 packet_id=66 flags=0x0 Jan 7 10:00:24.151: dsp_set_gains: [0:1:8] packet_Len=12 channel_id=4929 packet_id=91 in_gain=0 out_gain=0 Jan 7 10:00:24.151: dsp_vad_enable: [0:1:8] packet_Len=10 channel_id=4929 packet_id=78 thresh=-38 Jan 7 10:00:24.151: dsp_voice_mode: [0:1:8] packet_Len=24 channel_id=4929 packet_id=73 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode (VTSP_TONE_R2_MF_FORWARD_MODE) Jan 7 10:00:24.151: dsp_dtmf_mode: [0:1:8] packet_Len=10 channel_id=4929 packet_id=65dtmf_or_mf=1 !--- Digit 5 is sent: Forward Signal Group I-5 (First DNIS digit). Jan 7 10:00:24.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=5, rtp_timestamp=0x04030000 dc_digit_up Jan 7 10:00:24.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received digit (5) Jan 7 10:00:24.203: CSM voice (1/60): Rcvd Digit detected(5) Jan 7 10:00:24.203: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_PRE_CALLERID R2 Got Event 5 !--- Send Backward Signal Group A-5 (caller category request). Jan 7 10:00:24.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5 Jan 7 10:00:24.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929packet_id=90 string=5 digits=1, time_on=65435, time_off=30 Jan 7 10:00:24.203: digit=, components=2, freq_of_first=1020, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:24.303: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=5, duration=30dc_digit Jan 7 10:00:24.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (5) Jan 7 10:00:24.303: CSM voice (1/60): Rcvd Digit detected(5) Jan 7 10:00:24.303: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event R2_TONE_OFF Jan 7 10:00:24.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:24.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:24.303: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Caller Category Forward Signal Group II-1 is sent. Jan 7 10:00:24.403: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:24.403: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8)received digit (1) Jan 7 10:00:24.403: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:24.403: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event 1 !--- Send Backward Signal Group A-5 (Caller ID request). Jan 7 10:00:24.403: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5 Jan 7 10:00:24.403: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=5 digits=1, time_on=65435, time_off=30 Jan 7 10:00:24.403: digit=, components=2, freq_of_first=1020, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:24.503: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1, duration=30dc_digit Jan 7 10:00:24.503: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1) Jan 7 10:00:24.503: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:24.503: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event R2_TONE_OFF Jan 7 10:00:24.503: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:24.503: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:24.503: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- First ANI digit is sent: Forward Signal Group I-1. Jan 7 10:00:24.603: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:24.603: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (1) Jan 7 10:00:24.603: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:24.603: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event 1 !--- Send Backward Signal Group A-5 (Caller ID request). Jan 7 10:00:24.603: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5 Jan 7 10:00:24.603: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=5 digits=1, time_on=65435, time_off=30 Jan 7 10:00:24.603: digit=, components=2, freq_of_first=1020, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:24.703: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1, duration=30dc_digit Jan 7 10:00:24.703: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1) Jan 7 10:00:24.703: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:24.703: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event R2_TONE_OFF Jan 7 10:00:24.703: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:24.703: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:24.703: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Second ANI digit is sent: Forward Signal Group I-2. Jan 7 10:00:24.803: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN:digit=2, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:24.803: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (2) Jan 7 10:00:24.803: CSM voice (1/60): Rcvd Digit detected(2) Jan 7 10:00:24.803: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event 2 !--- Send Backward Signal Group A-5 (Caller ID request). Jan 7 10:00:24.803: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5 Jan 7 10:00:24.803: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929packet_id=90 string=5 digits=1, time_on=65435, time_off=30 Jan 7 10:00:24.803: digit=, components=2, freq_of_first=1020, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:24.903: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=2, duration=30dc_digit Jan 7 10:00:24.903: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (2) Jan 7 10:00:24.903: CSM voice (1/60): Rcvd Digit detected(2) Jan 7 10:00:24.903: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event R2_TONE_OFF Jan 7 10:00:24.903: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:24.903: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:24.903: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Third ANI digit is sent: Forward Signal Group I-3. Jan 7 10:00:25.003: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=3, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:25.003: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (3) Jan 7 10:00:25.003: CSM voice (1/60): Rcvd Digit detected(3) Jan 7 10:00:25.003: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event 3 !--- Send Backward Signal Group A-5 (Caller ID request). Jan 7 10:00:25.003: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 5 Jan 7 10:00:25.003: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=5 digits=1, time_on=65435, time_off=30 Jan 7 10:00:25.003: digit=, components=2, freq_of_first=1020, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:25.103: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=3, duration=30dc_digit Jan 7 10:00:25.103: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (3) Jan 7 10:00:25.103: CSM voice (1/60): Rcvd Digit detected(3) Jan 7 10:00:25.103: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event R2_TONE_OFF Jan 7 10:00:25.103: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:25.103: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:25.103: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Digit 15 is sent: Forward Signal Group I-15 (end of ANI digit). Jan 7 10:00:25.203: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=15, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:25.203: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (*) Jan 7 10:00:25.203: CSM voice (1/60): Rcvd Digit detected(*) Jan 7 10:00:25.203: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CALLERID R2 Got Event 15 !--- Send Backward Signal Group A-1 (next DNIS digit). Jan 7 10:00:25.203: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1 Jan 7 10:00:25.203: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=1 digits=1, time_on=65435, time_off=30 Jan 7 10:00:25.203: digit=, components=2, freq_of_first=1020, freq_of_second=1140, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:25.303: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=15, duration=30dc_digit Jan 7 10:00:25.303: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (*) Jan 7 10:00:25.303: CSM voice (1/60): Rcvd Digit detected(*) Jan 7 10:00:25.303: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF Jan 7 10:00:25.303: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=5dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:25.303: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:25.303: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Second DNIS digit is sent: Forward Signal Group I-6. Jan 7 10:00:25.391: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=6, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:25.391: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (6) Jan 7 10:00:25.391: CSM voice (1/60): Rcvd Digit detected(6) Jan 7 10:00:25.391: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_COLLECT_DNIS R2 Got Event 6 !--- Send Backward Signal Group A-1. Jan 7 10:00:25.391: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=56dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1 Jan 7 10:00:25.391: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=1 digits=1, time_on=65435, time_off=30 Jan 7 10:00:25.391: digit=, components=2, freq_of_first=1020, freq_of_second=1140, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:25.491: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF:digit=6, duration=30dc_digit Jan 7 10:00:25.491: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (6) Jan 7 10:00:25.491: CSM voice (1/60): Rcvd Digit detected(6) Jan 7 10:00:25.491: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF Jan 7 10:00:25.491: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=56dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:25.491: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:25.491: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Third DNIS digit is sent: Forward Signal Group I-7. Jan 7 10:00:25.583: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=7, rtp_timestamp=0x001E0010 dc_digit_up Jan 7 10:00:25.583: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (7) Jan 7 10:00:25.583: CSM voice (1/60): Rcvd Digit detected(7) Jan 7 10:00:25.583: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_COLLECT_DNIS R2 Got Event 7 !--- Send Backward Signal Group A-1. Jan 7 10:00:25.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 1 Jan 7 10:00:25.583: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=1 digits=1, time_on=65435, time_off=30 Jan 7 10:00:25.583: digit=, components=2, freq_of_first=1020, freq_of_second=1140, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:25.683: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=7, duration=30dc_digit Jan 7 10:00:25.683: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (7) Jan 7 10:00:25.683: CSM voice (1/60): Rcvd Digit detected(7) Jan 7 10:00:25.683: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_OFF Jan 7 10:00:25.683: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:25.683: dsp_dtmf_dialing: [0:1:8] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:25.683: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 Jan 7 10:00:25.835: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done() !--- Timeout is 3 seconds. Jan 7 10:00:28.583: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_COLLECT_DNIS R2 Got Event R2_TONE_TIMER !--- Send Backward Signal Group A-3: address-complete, changeover !--- to reception of group-B signal. Jan 7 10:00:28.583: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=567dc_dial()vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = 3# Jan 7 10:00:28.583: dsp_dtmf_dialing: [0:1:8] packet_Len=36 channel_id=4929 packet_id=90 string=3# digits=2, time_on=150, time_off=30 Jan 7 10:00:28.583: digit=, components=2, freq_of_first=1020, freq_of_second=900, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:28.583: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1 !--- Forward Signal Group II-1 is sent: subscriber without priority. Jan 7 10:00:28.831: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1, rtp_timestamp=0x001E0003 dc_digit_up Jan 7 10:00:28.831: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (1) Jan 7 10:00:28.831: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:28.831: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_CATEGORY R2 Got Event 1 Jan 7 10:00:28.831: CSM_PROC_IC1_COLLECT_ADDR_INFO: CSM_EVENT_ADDR_INFO_COLLECTED (DNIS=567, ANI=123) at slot 1, port 60 Jan 7 10:00:28.831: vtsp_tsp_call_accept_check (sdb=0x61DADEE0, calling_number=123 called_number=567): peer_tag=0 Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 7 10:00:28.835: VDEV_ALLOCATE: failed to allocate a device Jan 7 10:00:28.835: VDEV_ALLOCATE_ALMOST_READY: failed to allocate a non-idle modem Jan 7 10:00:28.835: CSM_PROC_IC3_WAIT_FOR_RES_RESP: CSM_EVENT_RESOURCE_OK at slot 1, port 60 Jan 7 10:00:28.835: vtsp_IC_switch : (voice_vdev= 0x61F19688) Jan 7 10:00:28.835: vtsp_tsp_call_switch_ind (cdb=0x61B5BFF8, tsp_info=0x61F19688, calling_number=123 called_number=567 redirect_number=): peer_tag=123dc_switch: fsm_pop() Jan 7 10:00:28.835: vtsp_do_call_setup_ind Jan 7 10:00:28.835: vtsp_do_call_setup_ind: Call ID=65581, guid=62031A88 Jan 7 10:00:28.835: vtsp_do_call_setup_ind: type=0, under_spec=0, name=b`, id0=9, id1=0, id2=0, calling=123, called=567 Jan 7 10:00:28.835: dsp_cp_tone_off: [] packet_Len=8 channel_id=4929 packet_id=71 Jan 7 10:00:28.835: dsp_idle_mode: [] packet_Len=8 channel_id=4929 packet_id=68 Jan 7 10:00:28.835: dsp_close_voice_channel: [] packet_Len=8 channel_id=4929 packet_id=75 Jan 7 10:00:28.835: vtsp_timer_stop: 7063006 Jan 7 10:00:28.839: csm_vtsp_call_setup_resp (vdev_info=0x61F19688, vtsp_cdb=0x61B5BFF8) Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:vdev_common BP TS allocatedat BP_stream0, BP_Ch8 Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 8 Jan 7 10:00:28.839: csm_vtsp_call_setup_resp:DST_tdm_chnl call. BP TS allocatedat stream 5, chan 13,BP_stream 0, BP_ch 8vtsp_open_voice_and_set_params Jan 7 10:00:28.839: dsp_close_voice_channel: [0:1 (17)] packet_Len=8 channel_id=4929 packet_id=75 Jan 7 10:00:28.839: dsp_open_voice_channel_20: [0:1 (17)] packet_Len=16 channel_id=4929 packet_id=74 alaw_ulaw_select=1 associated_signaling_channel=0 time_slot=0 serial_port=0 Jan 7 10:00:28.839: dsp_encap_config_20: [0:1 (17)] packet_Len=24 channel_id=4929 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0t_vpxcc=0x0 r_vpxcc=0x0 Jan 7 10:00:28.839: dsp_set_playout: [0:1 (17)] packet_Len=18 channel_id=4929 packet_id=76 mode=1 initial=60 min=4 max=200 fax_nom=300 Jan 7 10:00:28.839: dsp_echo_canceller_control: [0:1 (17)] packet_Len=10 channel_id=4929 packet_id=66 flags=0x0 Jan 7 10:00:28.839: dsp_set_gains: [0:1 (17)] packet_Len=12 channel_id=4929 packet_id=91 in_gain=0 out_gain=0 Jan 7 10:00:28.839: dsp_vad_enable: [0:1 (17)] packet_Len=10 channel_id=4929 packet_id=78 thresh=-38act_proceeding Jan 7 10:00:28.839: csm_vtsp_call_proceeding:DST_tdm_chnl call. BP TS allocatedstream 5, chan 13,BP_stream 0, BP_ch 8act_alert Jan 7 10:00:28.867: vtsp_ring_noan_timer_start: 7063009 Jan 7 10:00:28.867: csm_vtsp_call_alert (vtsp_cdb=0x61B5BFF8) Jan 7 10:00:28.867: csm_vtsp_call_alert: CSM_EVENT_ALERTING_RECEIVED Jan 7 10:00:28.867: CSM_IC5_WAIT_FOR_SWITCH_OVER: at slot 1, port 60 Jan 7 10:00:28.867: CSM_EVENT_ALERTING_RECEIVED: Jan 7 10:00:28.867: calling alerting_start_event !--- Note: For modems, Backward Signal !--- Group B-6 (subscriber's line free, charge) !--- is sent immediately. !--- For voice, it is delayed until alerting is received. !--- Notice that "R2_REJECT" is printed instead of R2_ALERTING. !--- This printing issue is solved in Cisco IOS Software Release 12.1T. Jan 7 10:00:28.867: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE:R2_IN_IDLE R2 Got Event R2_REJECT Jan 7 10:00:28.867: R2_ALERTING: r2_comp_idle Jan 7 10:00:28.867: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=567act_bridge Jan 7 10:00:28.867: dsp_voice_mode: [0:1 (17)] packet_Len=24 channel_id=4929 packet_id=73 coding_type=1 voice_field_size=80 VAD_flag=0 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0dsp_dtmf_mode (VTSP_TONE_R2_MF_FORWARD_MODE) !--- Answer signal (B-6) is sent after alerting is received. !--- Send Backward Signal Group B6 signal (Subscriber's line free, charge). Jan 7 10:00:28.871: dsp_dtmf_mode: [0:1 (17)] packet_Len=10 channel_id=4929 packet_id=65 dtmf_or_mf=1vtsp_r2_dial vtsp_r2_dial(): fsm_push(vtsp_r2_state_table) dsp_dtmf_dialing(): dial_string = 6 Jan 7 10:00:28.871: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24 channel_id=4929 packet_id=90 string=6 digits=1, time_on=65435, time_off=30 Jan 7 10:00:28.871: digit=, components=2, freq_of_first=900, freq_of_second=780, amp_of_first=8192, amp_of_second=8192 Jan 7 10:00:28.923: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_BEGIN: digit=1, rtp_timestamp=0x001E0006 dc_digit_up Jan 7 10:00:28.923: csm_vtsp_digit_ready_up (vtsp_cdb=0x61B5BFF8) received digit (1) Jan 7 10:00:28.923: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:28.923: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_COMPLETE R2 Got Event 1 Jan 7 10:00:28.971: vtsp_process_dsp_message: MSG_TX_DTMF_DIGIT_OFF: digit=1, duration=30dc_digit Jan 7 10:00:28.971: csm_vtsp_digit_ready (vtsp_cdb=0x61B5BFF8) received digit (1) Jan 7 10:00:28.971: CSM voice (1/60): Rcvd Digit detected(1) Jan 7 10:00:28.971: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_COMPLETE R2 Got Event R2_TONE_OFF Jan 7 10:00:28.971: vtsp_r2_generate_digits: vdev_common=0x6205E5F8, string=567dc_dial() vtsp_dial_nopush dsp_dtmf_dialing(): dial_string = # Jan 7 10:00:28.971: dsp_dtmf_dialing: [0:1 (17)] packet_Len=24 channel_id=4929 packet_id=90 string=# digits=1, time_on=150, time_off=30 Jan 7 10:00:28.975: digit=, components=2, freq_of_first=0, freq_of_second=0, amp_of_first=1, amp_of_second=1ds_dialing_defaultds_dialing_default Jan 7 10:00:29.127: vtsp_process_dsp_message: MSG_TX_DIALING_DONEdc_dialing_done() Jan 7 10:00:29.971: R2 Incoming Voice(1/60): DSX (E1 0:8): STATE: R2_IN_WAIT_GUARD R2 Got Event R2_TONE_TIMER Jan 7 10:00:29.971: R2_IN_IDLE:2 r2_in_connect called Jan 7 10:00:29.971: R2_IN_CONNECT: call end dial Jan 7 10:00:29.971: pop the dial state machine Jan 7 10:00:29.971: vtsp_r2_end_dial: vdev_common=0x6205E5F8, string=567ds_end_dial(): fsm_pop() act_caps_ind Jan 7 10:00:29.971: act_caps_ind:Encap 1, Vad 2, Codec 0x4, CodecBytes 20, FaxRate 2, FaxBytes 20 SignalType 0 DtmfRelay 1, Modem 1act_caps_ack Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8 channel_id=4929 packet_id=68 Jan 7 10:00:29.971: act_caps_ack: codec = 15, ret = 1 Jan 7 10:00:29.971: dsp_cp_tone_off: [0:1 (17)] packet_Len=8 channel_id=4929 packet_id=71 Jan 7 10:00:29.971: dsp_idle_mode: [0:1 (17)] packet_Len=8 channel_id=4929 packet_id=68 Jan 7 10:00:29.971: dsp_encap_config_20: [0:1 (17)] packet_Len=24 channel_id=4929 packet_id=92 TransportProtocol 2 t_ssrc=0x0 r_ssrc=0x0 t_vpxcc=0x0 r_vpxcc=0x0 Jan 7 10:00:29.971: dsp_voice_mode: [0:1 (17)] packet_Len=24 channel_id=4929 packet_id=73 coding_type=19 voice_field_size=20 VAD_flag=1 echo_length=64 comfort_noise=1 inband_detect=1 digit_relay=2 AGC_flag=0act_alert_connect Jan 7 10:00:30.255: vtsp_ring_noan_timer_stop: 7063148 Jan 7 10:00:30.255: dsp_cp_tone_off: [0:1 (17)] packet_Len=8 channel_id=4929 packet_id=71 Jan 7 10:00:30.255: csm_vtsp_call_connect (vtsp_cdb=0x61B5BFF8, voice_vdev=0x61F19688) Jan 7 10:00:30.255: CSM_IC5_WAIT_FOR_SWITCH_OVER: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 60 Jan 7 10:00:30.607: CSM_RX_CAS_EVENT_FROM_NEAT:(0007): EVENT_CHANNEL_CONNECTED at slot 1 and port 60 Jan 7 10:00:30.607: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_DSX0_CONNECTED at slot 1, port 60 Jan 7 10:00:30.607: from NEAT(0): (0/8): TX ANSWERED (ABCD=0101) eefje#