Ce document fournit un exemple de configuration pour le VPN DMVPN (Hub and Spoke Dynamic Multipoint VPN) utilisant l'encapsulation de routage générique (GRE) sur IPSec avec le protocole EIGRP (Enhanced Interior Gateway Routing Protocol), la traduction d'adresses réseau (NAT) et le contrôle d'accès basé sur le contexte (CBAC).
Avant d'établir un tunnel GRE (mGRE) multipoint et IPSec, vous devez définir une stratégie IKE (Internet Key Exchange) à l'aide de la commande crypto isakmp policy.
Remarque : Pour en savoir plus sur les commandes utilisées dans le présent document, utilisez l’outil de recherche de commandes (clients inscrits seulement).
Les informations contenues dans ce document sont basées sur les versions de matériel et de logiciel suivantes :
Logiciel Cisco IOS® Version 12.2(15)T1 sur le routeur concentrateur et 12.3(1.6) sur les routeurs en étoile
Cisco 3620 comme routeur concentrateur, deux routeurs Cisco 1720 et un routeur Cisco 3620 comme routeur en étoile
Les informations présentées dans ce document ont été créées à partir de périphériques dans un environnement de laboratoire spécifique. All of the devices used in this document started with a cleared (default) configuration. Si vous travaillez dans un réseau opérationnel, assurez-vous de bien comprendre l'impact potentiel de toute commande avant de l'utiliser.
Pour plus d'informations sur les conventions des documents, référez-vous aux Conventions utilisées pour les conseils techniques de Cisco.
Cette section vous fournit des informations pour configurer les fonctionnalités décrites dans ce document.
Remarque : Pour en savoir plus sur les commandes utilisées dans le présent document, utilisez l’outil de recherche de commandes (clients inscrits seulement).
Ce document utilise la configuration réseau indiquée dans le diagramme suivant :
Ce document utilise les configurations présentées ci-dessous.
Concentrateur - 3620-B |
---|
3620-B#write terminal Building configuration... Current configuration : 2607 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname 3620-B ! logging queue-limit 100 ! memory-size iomem 10 ip subnet-zero ! ! ip cef no ip domain lookup ! !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out ftp ip inspect name in2out tftp ip inspect name in2out tcp timeout 43200 ip inspect name in2out http ip inspect name in2out udp ip audit po max-events 100 ! ! ! !--- Create an Internet Security Association and Key Management !--- Protocol (ISAKMP) policy for Phase 1 negotiations. ! crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. !--- Here "dmvpn" is the word that is used as the key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 crypto isakmp nat keepalive 20 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.117.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description MULTI-POINT GRE TUNNEL for BRANCHES bandwidth 1000 ip address 172.16.0.1 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map multicast dynamic ip nhrp network-id 99 ip nhrp holdtime 300 no ip split-horizon eigrp 1 no ip mroute-cache delay 1000 tunnel source FastEthernet0/0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! !--- This is the outside interface. interface FastEthernet0/0 ip address 14.24.117.1 255.255.0.0 ip nat outside ip access-group 100 in ip inspect in2out out no ip mroute-cache duplex auto speed auto ! interface Serial0/0 no ip address shutdown clockrate 2000000 no fair-queue ! interface FastEthernet0/1 no ip address no ip mroute-cache duplex auto speed auto ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks over the tunnels. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.117.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out FastEthernet0/0. ip nat inside source list 110 interface FastEthernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ip route 2.0.0.0 255.0.0.0 14.24.121.1 ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open other inbound access as needed. access-list 100 permit udp any host 14.24.117.1 eq 500 access-list 100 permit esp any host 14.24.117.1 access-list 100 permit gre any host 14.24.117.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.117.0 0.0.0.255 any ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! ! end 3620-B# |
Spoke 1 - 3620-A |
---|
3620-A#write terminal Building configuration... Current configuration : 2559 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 3620-A ! boot system flash slot0:c3620-ik9o3s7-mz.122-15.T1.bin logging queue-limit 100 ! memory-size iomem 15 ip subnet-zero ! ! ip cef no ip domain lookup ! !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! no voice hpi capture buffer no voice hpi capture destination ! ! mta receive maximum-recipients 0 ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.118.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.2 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip mroute-cache delay 1000 tunnel source Ethernet0/0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! !--- This is the outside interface. interface Ethernet0/0 ip address 14.24.118.1 255.255.0.0 ip nat outside ip inspect in2out out ip access-group 100 in no ip mroute-cache half-duplex ! interface Ethernet0/1 no ip address half-duplex ! interface Ethernet0/2 no ip address shutdown half-duplex ! interface Ethernet0/3 no ip address shutdown half-duplex ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks over the tunnel. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.118.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out Ethernet0/0. ip nat inside source list 110 interface Ethernet0/0 overload ip http server no ip http secure-server ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed. access-list 100 permit udp any host 14.24.118.1 eq 500 access-list 100 permit esp any host 14.24.118.1 access-list 100 permit gre any host 14.24.118.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.118.0 0.0.0.255 any ! ! call rsvp-sync ! ! mgcp profile default ! dial-peer cor custom ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! ! end 3620-A# |
Spoke 2 - 1720-b |
---|
1720-b#write terminal Building configuration... Current configuration : 2543 bytes ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 1720-b ! boot system flash flash:c1700-ny-mz.122-8.YJ logging queue-limit 100 enable password cisco ! username 7206-B password 0 cisco ip subnet-zero ! ! no ip domain lookup ! ip cef !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! vpdn-group 1 request-dialin protocol pppoe ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.116.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.3 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip mroute-cache delay 1000 tunnel source Dialer1 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! interface Ethernet0 no ip address half-duplex ! interface FastEthernet0 no ip address no ip mroute-cache speed auto pppoe enable pppoe-client dial-pool-number 1 ! !--- This is the outside interface. interface Dialer1 ip address 2.2.2.10 255.255.255.0 ip inspect in2out out ip access-group 100 in encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication pap chap callin ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.116.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out Dialer1. ip nat inside source list 110 interface Dialer1 overload ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed. access-list 100 permit udp any host 14.24.116.1 eq 500 access-list 100 permit esp any host 14.24.116.1 access-list 100 permit gre any host 14.24.116.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.116.0 0.0.0.255 any dialer-list 1 protocol ip permit ! ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! no scheduler allocate end 1720-b# |
Spoke 3 - 1720-A |
---|
1720-A#write terminal Building configuration... Current configuration : 1770 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname 1720-A ! logging queue-limit 100 ! memory-size iomem 25 ip subnet-zero ! ! ! ip cef !--- This is the CBAC configuration and what to inspect. !--- This will be applied outbound on the external interface. ip inspect name in2out rcmd ip inspect name in2out tftp ip inspect name in2out udp ip inspect name in2out tcp timeout 43200 ip inspect name in2out realaudio ip inspect name in2out vdolive ip inspect name in2out netshow ip audit po max-events 100 ! ! !--- Create an ISAKMP policy for !--- Phase 1 negotiations. crypto isakmp policy 5 authentication pre-share group 2 !--- Add dynamic pre-shared key. crypto isakmp key dmvpnkey address 0.0.0.0 0.0.0.0 ! ! !--- Create the Phase 2 policy for actual data encryption. crypto ipsec transform-set dmvpnset esp-3des esp-sha-hmac ! !--- Create an IPSec profile to be applied dynamically !--- to the GRE over IPSec tunnels. crypto ipsec profile dmvpnprof set transform-set dmvpnset ! ! !--- This is the inside interface. interface Loopback1 ip address 192.168.120.1 255.255.255.0 ip nat inside ! !--- This is the mGRE interface for dynamic GRE tunnels. interface Tunnel1 description HOST DYNAMIC TUNNEL bandwidth 1000 ip address 172.16.0.4 255.255.255.0 no ip redirects ip mtu 1400 ip nhrp authentication dmvpn ip nhrp map 172.16.0.1 14.24.117.1 ip nhrp map multicast 14.24.117.1 ip nhrp network-id 99 ip nhrp holdtime 300 ip nhrp nhs 172.16.0.1 no ip mroute-cache delay 1000 tunnel source FastEthernet0 tunnel mode gre multipoint tunnel key 100000 tunnel protection ipsec profile dmvpnprof ! interface Ethernet0 no ip address no ip mroute-cache half-duplex ! !--- This is the outside interface. interface FastEthernet0 ip address 14.24.120.1 255.255.0.0 ip nat outside ip inspect in2out out ip access-group 100 in no ip mroute-cache speed auto ! !--- Enable a routing protocol to send/receive dynamic !--- updates about the private networks. router eigrp 1 network 172.16.0.0 0.0.0.255 network 192.168.120.0 no auto-summary ! !--- Perform NAT on local traffic !--- going directly out FastEthernet0. ip nat inside source list 110 interface FastEthernet0 overload ip classless ip route 0.0.0.0 0.0.0.0 14.24.1.1 no ip http server no ip http secure-server ! ! ! !--- Allow ISAKMP, ESP, and GRE traffic inbound. !--- CBAC will open inbound access as needed. access-list 100 permit udp any host 14.24.116.1 eq 500 access-list 100 permit esp any host 14.24.116.1 access-list 100 permit gre any host 14.24.116.1 access-list 100 deny ip any any access-list 110 permit ip 192.168.120.0 0.0.0.255 any ! ! ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 login ! no scheduler allocate end 1720-A# |
Cette section présente des informations que vous pouvez utiliser pour vous assurer que votre configuration fonctionne correctement.
Certaines commandes show sont prises en charge par l'Output Interpreter Tool (clients enregistrés uniquement), qui vous permet de voir une analyse de la sortie de la commande show.
show crypto isakmp sa : affiche l'état de l'association de sécurité ISAKMP (SA).
show crypto engine connections active : affiche le nombre total de chiffrement/déchiffrement par SA.
show crypto ipsec sa : affiche les statistiques sur les tunnels actifs.
show ip route : affiche la table de routage.
show ip eigrp neighbor : affiche les voisins EIGRP.
show ip nhrp - Affiche le cache NHRP (Next Hop Resolution Protocol) IP, éventuellement limité aux entrées de cache dynamique ou statique pour une interface spécifique.
show crypto socket : affiche la table de socket de chiffrement entre NHRP et IPSec.
Cette section fournit des informations que vous pouvez utiliser pour dépanner votre configuration.
Note : Avant d'émettre des commandes debug, consultez Informations importantes sur les commandes de débogage.
debug crypto ipsec — Affiche des événements IPsec.
debug crypto isakmp—Affichage de messages d'événements IKE.
debug crypto engine — Affiche des informations du moteur de chiffrement.
debug crypto socket - Affiche des informations sur la table de socket entre NHRP et IPSec.
debug nhrp - Affiche des informations sur les événements NHRP.
debug nhrp packet : affiche des informations sur les paquets NHRP.
debug tunnel protection : affiche des informations sur les tunnels GRE dynamiques.
Vous trouverez les informations supplémentaires pour dépanner IPSec à la section Dépannage de sécurité IP - Présentation et utilisation des commandes de débogage.
Révision | Date de publication | Commentaires |
---|---|---|
1.0 |
14-Jan-2008 |
Première publication |