Configuración y verificación de NAT en FTD

Opciones de descarga

PDF (1.7 MB)
Visualice con Adobe Reader en una variedad de dispositivos
ePub (1.5 MB)
Visualice en diferentes aplicaciones en iPhone, iPad, Android, Sony Reader o Windows Phone
Mobi (Kindle) (1.5 MB)
Visualice en dispositivo Kindle o aplicación Kindle en múltiples dispositivos

Actualizado:19 de diciembre de 2024

ID del documento:212702

Lenguaje no discriminatorio

El conjunto de documentos para este producto aspira al uso de un lenguaje no discriminatorio. A los fines de esta documentación, "no discriminatorio" se refiere al lenguaje que no implica discriminación por motivos de edad, discapacidad, género, identidad de raza, identidad étnica, orientación sexual, nivel socioeconómico e interseccionalidad. Puede haber excepciones en la documentación debido al lenguaje que se encuentra ya en las interfaces de usuario del software del producto, el lenguaje utilizado en función de la documentación de la RFP o el lenguaje utilizado por un producto de terceros al que se hace referencia. Obtenga más información sobre cómo Cisco utiliza el lenguaje inclusivo.

Acerca de esta traducción

Cisco ha traducido este documento combinando la traducción automática y los recursos humanos a fin de ofrecer a nuestros usuarios en todo el mundo contenido en su propio idioma. Tenga en cuenta que incluso la mejor traducción automática podría no ser tan precisa como la proporcionada por un traductor profesional. Cisco Systems, Inc. no asume ninguna responsabilidad por la precisión de estas traducciones y recomienda remitirse siempre al documento original escrito en inglés (insertar vínculo URL).

Contenido

Introducción

Prerequisites

Requirements

Componentes Utilizados

Antecedentes

Configurar

Diagrama de la red

Tarea 1. Configuración de NAT estática en FTD

Tarea 2. Configuración de la traducción de direcciones de puerto (PAT) en FTD

Tarea 3. Configuración de la exención de NAT en FTD

Tarea 4. Configuración de NAT de objetos en FTD

Tarea 5. Configuración del conjunto PAT en FTD

Verificación

Troubleshoot

Información Relacionada

Introducción

Este documento describe cómo configurar y verificar la traducción de direcciones de red (NAT) básica en Firepower Threat Defence (FTD).

Prerequisites

Requirements

No hay requisitos específicos para este documento.

Componentes Utilizados

La información que contiene este documento se basa en las siguientes versiones de software y hardware.

ASA5506X que ejecuta el código FTD 6.1.0-226
FireSIGHT Management Center (FMC) que ejecuta 6.1.0-226
3 hosts de Windows 7
Router Cisco IOS® 3925 que ejecuta VPN de LAN a LAN (L2L)

Hora de finalización del laboratorio: 1 hora

La información que contiene este documento se creó a partir de los dispositivos en un ambiente de laboratorio específico. Todos los dispositivos que se utilizan en este documento se pusieron en funcionamiento con una configuración verificada (predeterminada). Si tiene una red en vivo, asegúrese de entender el posible impacto de cualquier comando.

Antecedentes

FTD admite las mismas opciones de configuración de NAT que el dispositivo de seguridad adaptable (ASA) clásico:

Reglas NAT anteriores: equivalen a NAT doble (sección 1) en ASA clásico.
Reglas NAT automáticas - Sección 2 en ASA clásico
Reglas NAT después de: equivalen a NAT doble (sección 3) en ASA clásico.

Dado que la configuración de FTD se realiza desde el FMC cuando se trata de la configuración NAT, es necesario estar familiarizado con la GUI de FMC y las diversas opciones de configuración.

Configurar

Diagrama de la red

Tarea 1. Configuración de NAT estática en FTD

Configure NAT según estos requisitos:

Nombre de política NAT	Nombre del dispositivo FTD
Regla NAT	Regla NAT manual
Tipo de NAT	Estática
Insertar	En la sección 1
Interfaz de origen	interior*
Interfaz de destino	dmz*
Origen original	192.168.75.14
Origen traducido	192.168.76.100

*Usar zonas de seguridad para la regla NAT

Configure Static NAT on FTD

NAT estática

Solución:

Mientras que en el ASA clásico, debe utilizar nameif en las reglas NAT. En FTD, debe utilizar zonas de seguridad o grupos de interfaces.

Paso 1. Asignar interfaces a zonas de seguridad/grupos de interfaces.

En esta tarea, se decide asignar las interfaces FTD que se utilizan para NAT a las zonas de seguridad. Alternativamente, puede asignarlos a los grupos de interfaz como se muestra en la imagen.

Assign FTD Interfaces

Paso 2. El resultado es como se muestra en la imagen.

Interfaces Assigned

Paso 3. Puede crear/editar grupos de interfaz y zonas de seguridad desde la página Objetos > Gestión de Objetos como se muestra en la imagen.

Create/Edit Interface Groups and Security Zones

Zonas de seguridad frente a grupos de interfaces

La diferencia principal entre las zonas de seguridad y los grupos de interfaz es que una interfaz puede pertenecer a una sola zona de seguridad, pero puede pertenecer a varios grupos de interfaz. Así que prácticamente, los grupos de interfaz proporcionan más flexibilidad.

Puede ver que la interfaz interior pertenece a dos grupos de interfaz diferentes, pero sólo a una zona de seguridad como se muestra en la imagen.

Interface Inside Belongs to Two Different Interface Groups

Paso 4. Configuración de NAT estática en FTD.

Navegue hasta Devices > NAT y cree una política NAT. Seleccione New Policy > Threat Defence NAT como se muestra en la imagen.

Paso 5. Especifique el nombre de política y asígnelo a un dispositivo de destino como se muestra en la imagen.

Specify a Policy Name and Assign it to a Target Device

Paso 6. Agregue una regla NAT a la política, haga clic en Add Rule.

Especifique estos según los requisitos de la tarea como se muestra en las imágenes.

Add NAT Rule

Original Source and Original Destination

Host-A = 192.168.75.14

Host-B = 192.168.76.100

firepower# show run object
object network Host-A
 host 192.168.75.14
object network Host-B
 host 192.168.76.100

Advertencia: Si configura la NAT estática y especifica una interfaz como origen traducido, se redirige todo el tráfico destinado a la dirección IP de la interfaz. Los usuarios no pueden acceder a ningún servicio habilitado en la interfaz asignada. Algunos ejemplos de estos servicios incluyen protocolos de ruteo como OSPF y EIGRP.

Paso 7. El resultado es como se muestra en la imagen.

NAT is Configured

Paso 8. Asegúrese de que existe una política de control de acceso que permite al Host B acceder al Host A y viceversa. Recuerde que la NAT estática es bidireccional de forma predeterminada. De manera similar a los ASA clásicos, vea el uso de IP reales.Esto se espera ya que en este laboratorio, LINA ejecuta el código 9.6.1.x como se muestra en la imagen.

Access Control Policy that Allows Host-B to Access Host-A and Vice Versa

Verificación:

Desde CLI de LINA:

firepower# show run nat
nat (inside,dmz) source static Host-A Host-B

La regla NAT se insertó en la Sección 1 como se esperaba:

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 0, untranslate_hits = 0

Nota: Las 2 xlates que se crean en segundo plano.

firepower# show xlate
2 in use, 4 most used
Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
       s - static, T - twice, N - net-to-net
NAT from inside:192.168.75.14 to dmz:192.168.76.100
    flags sT idle 0:41:49 timeout 0:00:00
NAT from dmz:0.0.0.0/0 to inside:0.0.0.0/0
    flags sIT idle 0:41:49 timeout 0:00:00

Las tablas NAT de ASP:

firepower# show asp table classify domain nat

Input Table
in  id=0x7ff6036a9f50, priority=6, domain=nat, deny=false
        hits=0, user_data=0x7ff60314dbf0, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=dmz
in  id=0x7ff603696860, priority=6, domain=nat, deny=false
        hits=0, user_data=0x7ff602be3f80, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.76.100, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside

Output Table:
L2 - Output Table:
L2 - Input Table:
Last clearing of hits counters: Never

firepower# show asp table classify domain nat-reverse

Input Table

Output Table:
out id=0x7ff603685350, priority=6, domain=nat-reverse, deny=false
        hits=0, user_data=0x7ff60314dbf0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside
out id=0x7ff603638470, priority=6, domain=nat-reverse, deny=false
        hits=0, user_data=0x7ff602be3f80, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=dmz

L2 - Output Table:
L2 - Input Table:
Last clearing of hits counters: Never

Habilite la captura con detalles de seguimiento en FTD y haga ping del Host B al Host A y como se muestra en la imagen.

firepower# capture DMZ interface dmz trace detail match ip host 192.168.76.14 host 192.168.76.100
firepower# capture INSIDE interface inside trace detail match ip host 192.168.76.14 host 192.168.75.14

Enable Capture

El recuento de aciertos se encuentra en las tablas ASP:

firepower# show asp table classify domain nat

Input Table
in  id=0x7ff6036a9f50, priority=6, domain=nat, deny=false
        hits=0, user_data=0x7ff60314dbf0, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=dmz
in  id=0x7ff603696860, priority=6, domain=nat, deny=false
        hits=4, user_data=0x7ff602be3f80, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.76.100, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside

firepower# show asp table classify domain nat-reverse

Input Table

Output Table:
out id=0x7ff603685350, priority=6, domain=nat-reverse, deny=false
        hits=4, user_data=0x7ff60314dbf0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside
out id=0x7ff603638470, priority=6, domain=nat-reverse, deny=false
        hits=0, user_data=0x7ff602be3f80, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=dmz

La captura de paquetes muestra:

firepower# show capture DMZ
8 packets captured
   1: 17:38:26.324812       192.168.76.14 > 192.168.76.100: icmp: echo request
   2: 17:38:26.326505       192.168.76.100 > 192.168.76.14: icmp: echo reply
   3: 17:38:27.317991       192.168.76.14 > 192.168.76.100: icmp: echo request
   4: 17:38:27.319456       192.168.76.100 > 192.168.76.14: icmp: echo reply
   5: 17:38:28.316344       192.168.76.14 > 192.168.76.100: icmp: echo request
   6: 17:38:28.317824       192.168.76.100 > 192.168.76.14: icmp: echo reply
   7: 17:38:29.330518       192.168.76.14 > 192.168.76.100: icmp: echo request
   8: 17:38:29.331983       192.168.76.100 > 192.168.76.14: icmp: echo reply
8 packets shown

Rastros de un paquete (los puntos importantes están resaltados).

Nota: El ID de la regla NAT y su correlación con la tabla ASP.

firepower# show capture DMZ packet-number 3 trace detail
8 packets captured
   3: 17:38:27.317991 000c.2998.3fec d8b1.90b7.32e0 0x0800 Length: 74
      192.168.76.14 > 192.168.76.100: icmp: echo request (ttl 128, id 9975)
	  
Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff602c72be0, priority=13, domain=capture, deny=false
        hits=55, user_data=0x7ff602b74a50, cs_id=0x0, l3_type=0x0
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0000.0000.0000
        input_ifc=dmz, output_ifc=any
		
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff603612200, priority=1, domain=permit, deny=false
        hits=1, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=dmz, output_ifc=any
		
Phase: 3
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside,dmz) source static Host-A Host-B
Additional Information:
NAT divert to egress interface inside
Untranslate 192.168.76.100/0 to 192.168.75.14/0

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip host 192.168.76.14 host 192.168.75.14 rule-id 268434440
access-list CSM_FW_ACL_ remark rule-id 268434440: ACCESS POLICY: FTD5506-1 - Mandatory/2
access-list CSM_FW_ACL_ remark rule-id 268434440: L4 RULE: Host-B to Host-A
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached
 Forward Flow based lookup yields rule:
 in  id=0x7ff602b72610, priority=12, domain=permit, deny=false
        hits=1, user_data=0x7ff5fa9d0180, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=192.168.76.14, mask=255.255.255.255, port=0, tag=any, ifc=any
        dst ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any, ifc=any, vlan=0, dscp=0x0
        input_ifc=any, output_ifc=any
		
Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff60367cf80, priority=7, domain=conn-set, deny=false
        hits=1, user_data=0x7ff603677080, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=any
		
Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,dmz) source static Host-A Host-B
Additional Information:
Static translate 192.168.76.14/1 to 192.168.76.14/1
 Forward Flow based lookup yields rule:
 in  id=0x7ff603696860, priority=6, domain=nat, deny=false
        hits=1, user_data=0x7ff602be3f80, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.76.100, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside
		
Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff602220020, priority=0, domain=nat-per-session, deny=true
        hits=2, user_data=0x0, cs_id=0x0, reverse, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=any, output_ifc=any
		
Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff6035c0af0, priority=0, domain=inspect-ip-options, deny=true
        hits=1, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=any
		
Phase: 9
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
 match default-inspection-traffic
policy-map global_policy
 class inspection_default
  inspect icmp
service-policy global_policy global
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff602b5f020, priority=70, domain=inspect-icmp, deny=false
        hits=2, user_data=0x7ff602be7460, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
        src ip/id=0.0.0.0, mask=0.0.0.0, icmp-type=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, icmp-code=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=any
		
Phase: 10
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
 Forward Flow based lookup yields rule:
 in  id=0x7ff602b3a6d0, priority=70, domain=inspect-icmp-error, deny=false
        hits=2, user_data=0x7ff603672ec0, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
        src ip/id=0.0.0.0, mask=0.0.0.0, icmp-type=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, icmp-code=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=any
		
Phase: 11
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,dmz) source static Host-A Host-B
Additional Information:
 Forward Flow based lookup yields rule:
 out id=0x7ff603685350, priority=6, domain=nat-reverse, deny=false
        hits=2, user_data=0x7ff60314dbf0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside
		
Phase: 12
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
 Reverse Flow based lookup yields rule:
 in  id=0x7ff602220020, priority=0, domain=nat-per-session, deny=true
        hits=4, user_data=0x0, cs_id=0x0, reverse, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=any, output_ifc=any
		
Phase: 13
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
 Reverse Flow based lookup yields rule:
 in  id=0x7ff602c56d10, priority=0, domain=inspect-ip-options, deny=true
        hits=2, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=any
		
Phase: 14
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 5084, packet dispatched to next module
Module information for forward flow ...
snp_fp_inspect_ip_options
snp_fp_snort
snp_fp_inspect_icmp
snp_fp_translate
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Module information for reverse flow ...
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_inspect_icmp
snp_fp_snort
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat

Phase: 15
Type: EXTERNAL-INSPECT
Subtype:
Result: ALLOW
Config:
Additional Information:
Application: 'SNORT Inspect'

Phase: 16
Type: SNORT
Subtype:
Result: ALLOW
Config:
Additional Information:
Snort Verdict: (pass-packet) allow this packet

Phase: 17
Type: ROUTE-LOOKUP
Subtype: Resolve Egress Interface
Result: ALLOW
Config:
Additional Information:
found next-hop 192.168.75.14 using egress ifc  inside

Phase: 18
Type: ADJACENCY-LOOKUP
Subtype: next-hop and adjacency
Result: ALLOW
Config:
Additional Information:
adjacency Active
next-hop mac address 000c.2930.2b78 hits 140694538708414

Phase: 19
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
 Forward Flow based lookup yields rule:
 out id=0x7ff6036a94e0, priority=13, domain=capture, deny=false
        hits=14, user_data=0x7ff6024aff90, cs_id=0x0, l3_type=0x0
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0000.0000.0000
        input_ifc=inside, output_ifc=any
		
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: allow
1 packet shown

Tarea 2. Configuración de la traducción de direcciones de puerto (PAT) en FTD

Configure NAT según estos requisitos:

Regla NAT	Regla NAT manual
Tipo de NAT	Dinámico
Insertar	En la sección 1
Interfaz de origen	interior*
Interfaz de destino	exterior*
Origen original	192.168.75.0/24
Origen traducido	Interfaz externa (PAT)

*Usar zonas de seguridad para la regla NAT

Configure Port Address Translation

NAT estática

PAT

Solución:

Paso 1. Agregue una segunda regla NAT y configúrela según los requisitos de la tarea, como se muestra en la imagen.

Add a Second NAT Rule

Paso 2. Aquí está cómo se configura PAT como se muestra en la imagen.

PAT Configuration

Paso 3. El resultado es como se muestra en la imagen.

End Result of PAT Configuration

Paso 4. Para el resto de este laboratorio, configure la política de control de acceso para permitir que todo el tráfico pase.

Verificación:

Configuración de NAT:

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 26, untranslate_hits = 26
2 (inside) to (outside) source dynamic Net_192.168.75.0_24bits interface
    translate_hits = 0, untranslate_hits = 0

En CLI de LINA, observe la nueva entrada:

firepower# show xlate
3 in use, 19 most used
Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
       s - static, T - twice, N - net-to-net
NAT from inside:192.168.75.14 to dmz:192.168.76.100
    flags sT idle 1:15:14 timeout 0:00:00
NAT from dmz:0.0.0.0/0 to inside:0.0.0.0/0
    flags sIT idle 1:15:14 timeout 0:00:00
NAT from outside:0.0.0.0/0 to inside:0.0.0.0/0
    flags sIT idle 0:04:02 timeout 0:00:00

Habilite la captura en la interfaz interna y externa. En la captura interna, habilite el seguimiento:

firepower# capture CAPI trace interface inside match ip host 192.168.75.14 host 192.168.77.1
firepower# capture CAPO interface outside match ip any host 192.168.77.1

Ping desde Host-A (192.168.75.14) a IP 192.168.77.1 como se muestra en la imagen.

Ping from Host-A to IP Address

En las capturas de LINA, puede ver la traducción de PAT:

firepower# show cap CAPI
8 packets captured
   1: 18:54:43.658001       192.168.75.14 > 192.168.77.1: icmp: echo request
   2: 18:54:43.659099       192.168.77.1 > 192.168.75.14: icmp: echo reply
   3: 18:54:44.668544       192.168.75.14 > 192.168.77.1: icmp: echo request
   4: 18:54:44.669505       192.168.77.1 > 192.168.75.14: icmp: echo reply
   5: 18:54:45.682368       192.168.75.14 > 192.168.77.1: icmp: echo request
   6: 18:54:45.683421       192.168.77.1 > 192.168.75.14: icmp: echo reply
   7: 18:54:46.696436       192.168.75.14 > 192.168.77.1: icmp: echo request
   8: 18:54:46.697412       192.168.77.1 > 192.168.75.14: icmp: echo reply

firepower# show cap CAPO
8 packets captured
   1: 18:54:43.658672       192.168.77.6 > 192.168.77.1: icmp: echo request
   2: 18:54:43.658962       192.168.77.1 > 192.168.77.6: icmp: echo reply
   3: 18:54:44.669109       192.168.77.6 > 192.168.77.1: icmp: echo request
   4: 18:54:44.669337       192.168.77.1 > 192.168.77.6: icmp: echo reply
   5: 18:54:45.682932       192.168.77.6 > 192.168.77.1: icmp: echo request
   6: 18:54:45.683207       192.168.77.1 > 192.168.77.6: icmp: echo reply
   7: 18:54:46.697031       192.168.77.6 > 192.168.77.1: icmp: echo request
   8: 18:54:46.697275       192.168.77.1 > 192.168.77.6: icmp: echo reply

Rastros de un paquete con secciones importantes resaltadas:

firepower# show cap CAPI packet-number 1 trace
8 packets captured
   1: 18:54:43.658001       192.168.75.14 > 192.168.77.1: icmp: echo request
   
Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list

Phase: 3
Type: ROUTE-LOOKUP
Subtype: Resolve Egress Interface
Result: ALLOW
Config:
Additional Information:
found next-hop 192.168.77.1 using egress ifc  outside

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip any any rule-id 268434434
access-list CSM_FW_ACL_ remark rule-id 268434434: ACCESS POLICY: FTD5506-1 - Default/1
access-list CSM_FW_ACL_ remark rule-id 268434434: L4 RULE: DEFAULT ACTION RULE
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached
 
Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:

Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface
Additional Information:
Dynamic translate 192.168.75.14/1 to 192.168.77.6/1

Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 9
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
 match default-inspection-traffic
policy-map global_policy
 class inspection_default
  inspect icmp
service-policy global_policy global
Additional Information:

Phase: 10
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:

Phase: 11
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface
Additional Information:

Phase: 12
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 13
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 14
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 6981, packet dispatched to next module

Phase: 15
Type: EXTERNAL-INSPECT
Subtype:
Result: ALLOW
Config:
Additional Information:
Application: 'SNORT Inspect'

Phase: 16
Type: SNORT
Subtype:
Result: ALLOW
Config:
Additional Information:
Snort Verdict: (pass-packet) allow this packet

Phase: 17
Type: ROUTE-LOOKUP
Subtype: Resolve Egress Interface
Result: ALLOW
Config:
Additional Information:
found next-hop 192.168.77.1 using egress ifc  outside

Phase: 18
Type: ADJACENCY-LOOKUP
Subtype: next-hop and adjacency
Result: ALLOW
Config:
Additional Information:
adjacency Active
next-hop mac address c84c.758d.4980 hits 140694538709114

Phase: 19
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
1 packet shown

Se creó la xlate dinámica (observe los indicadores de ri):

firepower# show xlate
4 in use, 19 most used
Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
       s - static, T - twice, N - net-to-net
NAT from inside:192.168.75.14 to dmz:192.168.76.100
    flags sT idle 1:16:47 timeout 0:00:00
NAT from dmz:0.0.0.0/0 to inside:0.0.0.0/0
    flags sIT idle 1:16:47 timeout 0:00:00
NAT from outside:0.0.0.0/0 to inside:0.0.0.0/0
    flags sIT idle 0:05:35 timeout 0:00:00

ICMP PAT from inside:192.168.75.14/1 to outside:192.168.77.6/1 flags ri idle 0:00:30 timeout 0:00:30

En los registros de LINA verá:

firepower# show log
May 31 2016 18:54:43: %ASA-7-609001: Built local-host inside:192.168.75.14
May 31 2016 18:54:43: %ASA-6-305011: Built dynamic ICMP translation from inside:192.168.75.14/1 to outside:192.168.77.6/1
May 31 2016 18:54:43: %ASA-7-609001: Built local-host outside:192.168.77.1
May 31 2016 18:54:43: %ASA-6-302020: Built inbound ICMP connection for faddr 192.168.75.14/1 gaddr 192.168.77.1/0 laddr 192.168.77.1/0
May 31 2016 18:54:43: %ASA-6-302021: Teardown ICMP connection for faddr 192.168.75.14/1 gaddr 192.168.77.1/0 laddr 192.168.77.1/0
May 31 2016 18:54:43: %ASA-7-609002: Teardown local-host outside:192.168.77.1 duration 0:00:00
May 31 2016 18:55:17: %ASA-6-305012: Teardown dynamic ICMP translation from inside:192.168.75.14/1 to outside:192.168.77.6/1 duration 0:00:34

Secciones de NAT:

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 26, untranslate_hits = 26
2 (inside) to (outside) source dynamic Net_192.168.75.0_24bits interface
    translate_hits = 94, untranslate_hits = 138

Las tablas ASP muestran:

firepower# show asp table classify domain nat

Input Table
in  id=0x7ff6036a9f50, priority=6, domain=nat, deny=false
        hits=0, user_data=0x7ff60314dbf0, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=dmz
in  id=0x7ff603696860, priority=6, domain=nat, deny=false
        hits=4, user_data=0x7ff602be3f80, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.76.100, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside
in  id=0x7ff602c75f00, priority=6, domain=nat, deny=false
        hits=94, user_data=0x7ff6036609a0, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=192.168.75.0, mask=255.255.255.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=outside
in  id=0x7ff603681fb0, priority=6, domain=nat, deny=false
        hits=276, user_data=0x7ff60249f370, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.77.6, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=outside, output_ifc=inside

firepower# show asp table classify domain nat-reverse

Input Table

Output Table:
out id=0x7ff603685350, priority=6, domain=nat-reverse, deny=false
        hits=4, user_data=0x7ff60314dbf0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any, dscp=0x0
        input_ifc=dmz, output_ifc=inside
out id=0x7ff603638470, priority=6, domain=nat-reverse, deny=false
        hits=0, user_data=0x7ff602be3f80, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=192.168.75.14, mask=255.255.255.255, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=dmz
out id=0x7ff60361bda0, priority=6, domain=nat-reverse, deny=false
        hits=138, user_data=0x7ff6036609a0, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any
        dst ip/id=192.168.75.0, mask=255.255.255.0, port=0, tag=any, dscp=0x0
        input_ifc=outside, output_ifc=inside
out id=0x7ff60361c180, priority=6, domain=nat-reverse, deny=false
        hits=94, user_data=0x7ff60249f370, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=192.168.75.0, mask=255.255.255.0, port=0, tag=any
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=any, dscp=0x0
        input_ifc=inside, output_ifc=outside

Tarea 3. Configuración de la exención de NAT en FTD

Configure NAT según estos requisitos:

Regla NAT	Regla NAT manual
Tipo de NAT	Estática
Insertar	En la sección 1, todas las normas existentes
Interfaz de origen	interior*
Interfaz de destino	exterior*
Origen original	192.168.75.0/24
Origen traducido	192.168.75.0/24
Destino original	10.1.1.0/24
Destino traducido	10.1.1.0/24

*Usar zonas de seguridad para la regla NAT

Configure NAT Exemption on FTD

NAT estática

PAT

Exención de NAT

Solución:

Paso 1. Agregue una tercera regla NAT y configure los requisitos por tarea como se muestra en la imagen.

Add a Third NAT Rule

Paso 2. Realice la búsqueda de ruta para determinar la interfaz de salida.

Nota: Para las reglas NAT de identidad, como la que agregó, puede cambiar cómo se determina la interfaz de salida y utilizar la búsqueda de ruta normal como se muestra en la imagen.

Perform Route Lookup

Verificación:

firepower# show run nat
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
nat (inside,dmz) source static Host-A Host-B
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits  destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
    translate_hits = 0, untranslate_hits = 0
2 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 26, untranslate_hits = 26
3 (inside) to (outside) source dynamic Net_192.168.75.0_24bits interface
    translate_hits = 96, untranslate_hits = 138

Ejecute packet-tracer para el tráfico no VPN originado en la red interna. La regla PAT se utiliza según lo esperado:

firepower# packet-tracer input inside tcp 192.168.75.14 1111 192.168.77.1 80

Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list

Phase: 3
Type: ROUTE-LOOKUP
Subtype: Resolve Egress Interface
Result: ALLOW
Config:
Additional Information:
found next-hop 192.168.77.1 using egress ifc  outside

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip any any rule-id 268434434
access-list CSM_FW_ACL_ remark rule-id 268434434: ACCESS POLICY: FTD5506-1 - Default/1
access-list CSM_FW_ACL_ remark rule-id 268434434: L4 RULE: DEFAULT ACTION RULE
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached
 
Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:

Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface
Additional Information:

Dynamic translate 192.168.75.14/1111 to 192.168.77.6/1111
Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 9
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface
Additional Information:

Phase: 10
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 11
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 12
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 7227, packet dispatched to next module

Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow

Ejecute packet-tracer para el tráfico que debe pasar a través del túnel VPN (ejecútelo dos veces desde que el primer intento activa el túnel VPN).

Nota: Debe elegir la regla de exención de NAT.

Primer intento de rastreo de paquetes:

firepower# packet-tracer input inside tcp 192.168.75.14 1111 10.1.1.1 80

Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list

Phase: 3
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
Additional Information:
NAT divert to egress interface outside
Untranslate 10.1.1.1/80 to 10.1.1.1/80

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip any any rule-id 268434434
access-list CSM_FW_ACL_ remark rule-id 268434434: ACCESS POLICY: FTD5506-1 - Default/1
access-list CSM_FW_ACL_ remark rule-id 268434434: L4 RULE: DEFAULT ACTION RULE
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached
 
Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:

Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
Additional Information:
Static translate 192.168.75.14/1111 to 192.168.75.14/1111

Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 9
Type: VPN
Subtype: encrypt
Result: DROP
Config:
Additional Information:

Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule

Segundo intento de rastreo de paquetes:

firepower# packet-tracer input inside tcp 192.168.75.14 1111 10.1.1.1 80

Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list

Phase: 3
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
Additional Information:
NAT divert to egress interface outside
Untranslate 10.1.1.1/80 to 10.1.1.1/80

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip any any rule-id 268434434
access-list CSM_FW_ACL_ remark rule-id 268434434: ACCESS POLICY: FTD5506-1 - Default/1
access-list CSM_FW_ACL_ remark rule-id 268434434: L4 RULE: DEFAULT ACTION RULE
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached
 
Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:

Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
Additional Information:
Static translate 192.168.75.14/1111 to 192.168.75.14/1111

Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 9
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
Additional Information:

Phase: 11
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:

Phase: 12
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 13
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 14
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 7226, packet dispatched to next module

Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow

Verificación de conteo de aciertos NAT:

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits  destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
    translate_hits = 9, untranslate_hits = 9
2 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 26, untranslate_hits = 26
3 (inside) to (outside) source dynamic Net_192.168.75.0_24bits interface
    translate_hits = 98, untranslate_hits = 138

Tarea 4. Configuración de NAT de objetos en FTD

Configure NAT según estos requisitos:

Regla NAT	Regla NAT automática
Tipo de NAT	Estática
Insertar	En la sección 2
Interfaz de origen	interior*
Interfaz de destino	dmz*
Origen original	192.168.75.99
Origen traducido	192.168.76.99
Traducir respuestas DNS que coincidan con esta regla	Habilitado

*Usar zonas de seguridad para la regla NAT

Solución:

Paso 1. Configure la regla según los requisitos de la tarea como se muestra en las imágenes.

Configure the Rule as per Task Requirements

Original Source

Translate DNS Replies that Match this Rule

Paso 2. El resultado es como se muestra en la imagen.

Final Result

Verificación:

firepower# show run nat
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
nat (inside,dmz) source static Host-A Host-B
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface
!
object network obj-192.168.75.99
 nat (inside,dmz) static obj-192.168.76.99 dns

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits  destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
    translate_hits = 9, untranslate_hits = 9
2 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 26, untranslate_hits = 26
3 (inside) to (outside) source dynamic Net_192.168.75.0_24bits interface
    translate_hits = 98, untranslate_hits = 138

Auto NAT Policies (Section 2)
1 (inside) to (dmz) source static obj-192.168.75.99 obj-192.168.76.99  dns
    translate_hits = 0, untranslate_hits = 0

Verificación con packet-tracer:

firepower# packet-tracer input inside tcp 192.168.75.99 1111 192.168.76.100 80

Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list

Phase: 3
Type: ROUTE-LOOKUP
Subtype: Resolve Egress Interface
Result: ALLOW
Config:
Additional Information:
found next-hop 192.168.76.100 using egress ifc  dmz

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip any any rule-id 268434434
access-list CSM_FW_ACL_ remark rule-id 268434434: ACCESS POLICY: FTD5506-1 - Default/1
access-list CSM_FW_ACL_ remark rule-id 268434434: L4 RULE: DEFAULT ACTION RULE
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached

Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:

Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
object network obj-192.168.75.99
 nat (inside,dmz) static obj-192.168.76.99 dns
Additional Information:
Static translate 192.168.75.99/1111 to 192.168.76.99/1111

Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 9
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 10
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 11
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 7245, packet dispatched to next module

Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: dmz
output-status: up
output-line-status: up
Action: allow

Tarea 5. Configuración del conjunto PAT en FTD

Configure NAT según estos requisitos:

Regla NAT	Regla NAT manual
Tipo de NAT	Dinámico
Insertar	En la sección 3
Interfaz de origen	interior*
Interfaz de destino	dmz*
Origen original	192.168.75.0/24
Origen traducido	192.168.76.20-22
Utilizar toda la gama (1-65535)	Habilitado

*Usar zonas de seguridad para la regla NAT

Solución:

Paso 1. Configure la regla según los requisitos de la tarea como se muestra en las imágenes.

Configure the Rule per Task Requirements for Manual NAT Rule

Result of Manual NAT Rule

Paso 2. Habilite Flat Port Range con Include Reserver Ports que permite el uso del rango completo (1-65535) como se muestra en la imagen.

Enable Flat Port Range with Include Reserver Porst

Paso 3. El resultado es como se muestra en la imagen.

Final Result of Flat Port Range

Verificación:

firepower# show run nat
nat (inside,outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
nat (inside,dmz) source static Host-A Host-B
nat (inside,outside) source dynamic Net_192.168.75.0_24bits interface
!
object network obj-192.168.75.99
 nat (inside,dmz) static obj-192.168.76.99 dns
!
nat (inside,dmz) after-auto source dynamic Net_192.168.75.0_24bits pat-pool range-192.168.76.20-22 flat include-reserve

La regla está en la Sección 3:

firepower# show nat
Manual NAT Policies (Section 1)
1 (inside) to (outside) source static Net_192.168.75.0_24bits Net_192.168.75.0_24bits  destination static net_10.1.1.0_24bits net_10.1.1.0_24bits
    translate_hits = 9, untranslate_hits = 9
2 (inside) to (dmz) source static Host-A Host-B
    translate_hits = 26, untranslate_hits = 26
3 (inside) to (outside) source dynamic Net_192.168.75.0_24bits interface
    translate_hits = 98, untranslate_hits = 138

Auto NAT Policies (Section 2)
1 (inside) to (dmz) source static obj-192.168.75.99 obj-192.168.76.99  dns
    translate_hits = 1, untranslate_hits = 0

Manual NAT Policies (Section 3)
1 (inside) to (dmz) source dynamic Net_192.168.75.0_24bits pat-pool range-192.168.76.20-22 flat include-reserve
    translate_hits = 0, untranslate_hits = 0

Verificación del trazador de paquetes:

firepower# packet-tracer input inside icmp 192.168.75.15 8 0 192.168.76.5

Phase: 1
Type: CAPTURE
Subtype:
Result: ALLOW
Config:
Additional Information:
MAC Access list

Phase: 2
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list

Phase: 3
Type: ROUTE-LOOKUP
Subtype: Resolve Egress Interface
Result: ALLOW
Config:
Additional Information:
found next-hop 192.168.76.5 using egress ifc  dmz

Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group CSM_FW_ACL_ global
access-list CSM_FW_ACL_ advanced permit ip any any rule-id 268434434
access-list CSM_FW_ACL_ remark rule-id 268434434: ACCESS POLICY: FTD5506-1 - Default/1
access-list CSM_FW_ACL_ remark rule-id 268434434: L4 RULE: DEFAULT ACTION RULE
Additional Information:
 This packet will be sent to snort for additional processing where a verdict will be reached
 
Phase: 5
Type: CONN-SETTINGS
Subtype:
Result: ALLOW
Config:
class-map class-default
 match any
policy-map global_policy
 class class-default
  set connection advanced-options UM_STATIC_TCP_MAP
service-policy global_policy global
Additional Information:

Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,dmz) after-auto source dynamic Net_192.168.75.0_24bits pat-pool range-192.168.76.20-22 flat include-reserve
Additional Information:
Dynamic translate 192.168.75.15/0 to 192.168.76.20/11654

Phase: 7
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 9
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
 match default-inspection-traffic
policy-map global_policy
 class inspection_default
  inspect icmp
service-policy global_policy global
Additional Information:

Phase: 10
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:

Phase: 11
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,dmz) after-auto source dynamic Net_192.168.75.0_24bits pat-pool range-192.168.76.20-22 flat include-reserve
Additional Information:

Phase: 12
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:

Phase: 13
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:

Phase: 14
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 7289, packet dispatched to next module

Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: dmz
output-status: up
output-line-status: up
Action: allow

Verificación

Utilize esta sección para confirmar que su configuración funcione correctamente.

La verificación se ha explicado en las secciones de tareas individuales.

Troubleshoot

En esta sección se brinda información que puede utilizar para resolver problemas en su configuración.

Abra la página Advanced Troubleshooting en el FMC, ejecute el packet-tracer y luego ejecute el comando show nat pool.

Nota: Entrada que utiliza todo el rango, como se muestra en la imagen.

Advanced Troubleshooting

Información Relacionada

Todas las versiones de la guía de configuración de Cisco Firepower Management Center se pueden encontrar aquí:

Navegación por la documentación de Cisco Secure Firewall Threat Defence

Cisco Global Technical Assistance Center (TAC) recomienda encarecidamente esta guía visual para obtener un conocimiento práctico en profundidad de las tecnologías de seguridad de última generación de Cisco Firepower, que incluye las mencionadas en este artículo:

Cisco Press: Firepower Threat Defence

Para todas las notas técnicas de configuración y resolución de problemas relacionadas con las tecnologías Firepower:

Cisco Secure Firewall Management Center

Soporte Técnico y Documentación - Cisco Systems

Historial de revisiones

Revisión	Fecha de publicación	Comentarios
3.0	19-Dec-2024	Actualización del código del cuadro de información interno de Cisco para que sea rojo y formato.
2.0	02-Aug-2023	Texto alternativo agregado. SEO actualizado, traducción automática, requisitos de estilo y formato.
1.0	29-Jan-2018	Versión inicial

Con la colaboración de ingenieros de Cisco

Mikis Zafeiroudis
Technical Consulting Engineer
John Long
Technical Consulting Engineer

¿Resultó útil este documento?

Comentarios

Contacte a Cisco

Abrir un caso de soporte
(Requiere un Cisco Service Contract)