Table Of Contents
Release Notes for Cisco Aironet Power Injector Media Converter (AIR-PWRINJ-FIB)
Installing in an Environmental Air Space
Obtaining Documentation and Submitting a Service Request
Release Notes for Cisco Aironet Power Injector Media Converter (AIR-PWRINJ-FIB)
July 10, 2003
These release notes describe caveats for the Cisco Aironet Power Injector Media Converter (AIR-PWRINJ-FIB). These release notes also contain important information about the power injector media converter.
Contents
These release notes describe the following topics:
•Obtaining Documentation and Submitting a Service Request
Introduction
The Cisco Aironet Power Injector Media Converter increases wireless LAN deployment flexibility of Cisco Aironet Access Points and Bridges by providing an alternative powering option to local power, inline power-capable multiport switches, and multiport power patch panels.
The power injector media converter combines 48-VDC power (supplied by the external power supply) with the data signal, sending both to the Cisco Aironet Access Point or Bridge.
The power injector media converter receives data over the fiber-optic cable through its MT-RJ fiber connector. The fiber-optic data signals are converted to Ethernet data signals and sent to the access point through the injector's Category 5 RJ-45 port. A Category 5 Ethernet cable connects the injector to the access point. The injector's power supply connects to a wall outlet or power strip to supply the power. An alternate 48-VDC power source can be used instead of the power supply.
The power injector media converter provides up to 15W over the unused wire pairs of a Category 5 Ethernet cable, supplying enough power for a distance of 328 ft (100 m) on the Cisco Aironet 350, 1100, an 1200 Series Access Points and the Cisco Aironet 350 Series Bridges.
Limitations and Restrictions
Installing in an Environmental Air Space
The Cisco Aironet Power Injector Media Converter (AIR-PWRINJ-FIB) provides adequate fire resistance and low smoke-producing characteristics suitable for operation in a building's environmental air space in accordance with Section 300-22(C) of the National Electrical Code (NEC) and Sections 2-128, 12-010(3), and 12-100 of the Canadian Electrical Code,
Part 1, C22.1.The AC power adapter is not suitable for operation in a building's environmental airspace and should not be installed in these environments. When installing the power injector media converter into a building's environmental air space, the power supply pigtail option, provided with your power injector, must be used.
Detailed mounting instructions are contained in the Quick Start Guide Cisco Aironet Power Injector Media Converter Cisco Aironet Power Injector, which shipped with your power injector media converter.
Stacking Power Injectors
Do not stack the AIR-PWRINJ-FIB.
MT-RJ Connector Limitation
MT-RJ cable assemblies that contain alignment pins (small metal pins in the connector) are not compatible with the Cisco media converter and will not mate correctly.
The MT-RJ connector is a small form factor connector that contains two fibers in one small polymer ferrule. When connecting to the power injector media converter you need to use a non-pinned MT-RJ cable assembly.
Documentation Updates
The illustration showing how to secure the pigtail to the power injector on page 24 of the Quick Start Guide Cisco Aironet Power Injector and Aironet Power Injector Media Converter is incorrect. Figure 1 shows the correct way to route the pigtail wires.
Figure 1 Pigtail Wiring Path
Caveats
This section lists caveats for the Cisco Aironet Power Injector Media Converter (AIR-PWRINJ-FIB).
Open Caveats
The following caveats have not been resolved.
•CSCea81288—Catalyst 2900 switch Fiber Link LED does not indicate correct status of the link.
The fiber link LED on a Catalyst 2900 switch is green even when the link is down.
There is no workaround for this caveat.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Copyright © 2003 Cisco Systems Inc.
All rights reserved.