About the Release Notes
This release notes document describes what is new or changed in this release, instructions to upgrade to this release, and provides information about the open and resolved caveats for this release. Unless otherwise noted, in this document, Cisco Wireless Controllers are referred to as controllers, and Cisco lightweight access points are referred to as access points or APs.
Supported Cisco Wireless Controller Platforms
The following controller platforms are supported in this release:
-
Cisco 3504 Wireless Controller
-
Cisco 5520 Wireless Controller
-
Cisco 8540 Wireless Controller
-
Cisco Virtual Wireless Controller (vWLC) on the following platforms:
-
VMware vSphere Hypervisor (ESXi) Version 5.x and 6.x
-
Hyper-V on Microsoft Server 2012 and later versions (support introduced in Release 8.4)
-
Kernel-based virtual machine (KVM) (support introduced in Release 8.1). After KVM is deployed, we recommend that you do not downgrade to a Cisco Wireless release that is earlier than Release 8.1).
-
-
Cisco Wireless Controllers for High Availability for Cisco 3504 Wireless Controller, Cisco 5520 Wireless Controller, and Cisco 8540 Wireless Controller
-
Cisco Mobility Express
Note |
In a network that includes Cisco Catalyst Center (formerly Cisco DNA Center) and Cisco AireOS controller, and the controller fails provisioning with Error NA serv CA certificate file transfer failed error, as a workaround, we recommend you reboot the affected AireOS controller. |
Supported Cisco Access Point Platforms
The following Cisco AP platforms are supported in this release:
-
Cisco Catalyst 9105 Access Points
-
C9105AXI: VID 03 and earlier
-
C9105AXW: VID 01
-
-
Cisco Catalyst 9130 Access Points
-
C9130AXE: VID 02 and earlier
-
C9130AXI: VID 02 and earlier
-
-
Cisco Catalyst 9120 Access Points
-
C9120AXI: VID 06 and earlier
-
C9120AXE: VID 06 and earlier
-
C9120AXP: All VIDs
-
-
Cisco Catalyst 9117 Access Points
-
Cisco Catalyst 9115 Access Points
-
Cisco Aironet 700 Series Access Points
-
Cisco Aironet 700W Series Access Points
-
Cisco AP803 Integrated Access Point
-
Integrated Access Point on Cisco 1100, 1101, and 1109 Integrated Services Routers
-
Cisco Aironet 1700 Series Access Points
-
Cisco Aironet 1800 Series Access Points
-
Cisco Aironet 1810 Series OfficeExtend Access Points
-
Cisco Aironet 1810W Series Access Points
-
Cisco Aironet 1815 Series Access Points
-
Cisco Aironet 1830 Series Access Points
-
Cisco Aironet 1840 Series Access Points
-
Cisco Aironet 1850 Series Access Points
-
Cisco Aironet 2700 Series Access Points
-
Cisco Aironet 2800 Series Access Points
-
Cisco Aironet 3700 Series Access Points
-
Cisco Aironet 3800 Series Access Points
-
Cisco Aironet 4800 Series Access Points
-
Cisco ASA 5506W-AP702
-
Cisco Aironet 1530 Series Access Points
-
Cisco Aironet 1540 Series Access Points
-
Cisco Aironet 1560 Series Access Points
-
Cisco Aironet 1570 Series Access Points
-
Cisco Industrial Wireless 3700 Series Access Points
-
Cisco Catalyst IW6300 Heavy Duty Series Access Points
-
Cisco 6300 Series Embedded Services Access Points
Cisco AP803 is an integrated access point module on the Cisco 800 Series Integrated Services Routers (ISRs). For more information about the stock-keeping units (SKUs) for the AP803 Cisco ISRs, see:
http://www.cisco.com/c/en/us/products/routers/800-series-routers/brochure-listing.html.For more information about the integrated access point on Cisco 1100 ISR, see the product data sheet:
https://www.cisco.com/c/en/us/products/collateral/routers/1000-series-integrated-services-routers-isr/datasheet-c78-739512.html.For information about the Cisco Wireless software releases that support specific Cisco access point modules, see the "Software Release Support for Specific Access Point Modules" section in the Cisco Wireless Solutions Software Compatibility Matrix document.
What's New in Release 8.10.151.0
This section provides a brief introduction to the new features and enhancements that are introduced in this release.
Note |
For a complete list of all the documentation published for Cisco Wireless Release 8.10, see the Documentation Roadmap at: https://www.cisco.com/c/en/us/td/docs/wireless/doc-roadmap/doc-roadmap-release-810.html |
Per–WLAN 802.11ax Mode
From this release onwards, you can enable or disable the 802.11ax radio and its features on a per-WLAN basis.
For more information, see:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810/per_wlan_wireless_settings.html#info_per-wlan_11ax_modeRandom MAC Filtering
This feature provides enhanced security and telemetry based on the policies applied on the clients joining the network. You can configure the network to deny clients joining with random MAC address, also known as locally-administered MAC addresses, feature enabled.
For more information, see:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810/wlan_security.html#info_random_mac_filteringIoT Features
-
USB Support for IW6300: USB configuration is supported on Cisco Catalyst Industrial Wireless 6300 Heavy Duty Series Access Points from this release.
For more information, see the USB Support section in the Cisco Catalyst IW6300 Heavy Duty Series and 6300 Series Embedded Services Access Point Software Configuration Guide.
-
Larger memory and NAND flash upgrade for IW6300 and ESW6300: Hardware upgrade of 2048-MB DDR4 memory and 8-bit ECC 1024–MB NAND flash for Cisco Catalyst IW6300 Heavy Duty Series and 6300 Series Embedded Services Access Points are added in this release.
For more information, see the Cisco Catalyst IW6300 Heavy Duty Series Access Point Hardware Installation Guide.
Software Release Types and Recommendations
Release Type |
Description |
Benefit |
---|---|---|
Maintenance Deployment (MD) |
Software releases that provide bug-fix support and ongoing software maintenance. These releases are categorized as Maintenance Deployment (MD). These releases are long-living releases with ongoing software maintenance. |
Provides you with a software release that offers stability and long support duration with periodic maintenance releases (MRs). |
Early Deployment (ED) |
Software releases that provide new features and new hardware platform support in addition to bug fixes. These releases are categorized as Early Deployment (ED). These releases are short-lived releases. |
Allows you to deploy the latest features and new hardware platforms or modules. |
For detailed release recommendations, see the Guidelines for Cisco Wireless Software Release Migration Bulletin at:
http://www.cisco.com/c/en/us/products/collateral/wireless/8500-series-wireless-controllers/bulletin-c25-730741.html.
Current Software Release |
Upgrade Path to Release 8.10.151.0 |
---|---|
8.5.x |
You can upgrade directly to Release 8.10.151.0. |
8.6.x |
You can upgrade directly to Release 8.10.151.0. |
8.7.x |
You can upgrade directly to Release 8.10.151.0. |
8.8.x |
You can upgrade directly to Release 8.10.151.0. |
8.9.x |
You can upgrade directly to Release 8.10.151.0. |
8.10.x |
You can upgrade directly to Release 8.10.151.0. |
Upgrading a Cisco Wireless Release
This section describes the guidelines and limitations that you must be aware of when you are upgrading the Cisco Wireless release and the procedure to upgrade.
Guidelines and Limitations
-
An existing WLAN with ? in its name continues to be supported with this upgrade. However, you cannot include ? in the name when creating a new WLAN.
-
If an AP locks out the console due to default management user credentials, you must configure the controller AP global credential with non-default username and password to get access to the AP console.
-
WPA3 upgrade and downgrade guidelines:
-
If you want to upgrade from Release 8.5 to 8.10 and have WPA1 configured with none of the WPA1 AKM valid for Release 8.10, the WPA1 configuration is disabled after the upgrade.
-
If you downgrade from Release 8.10 to Release 8.5, if any AKM for SAE is configured, the AKM validation fails after the downgrade. The security is set to WPA2 and AKM to 802.1X. However, PMF configuration is retained, which results in an error.
-
FT set to enabled state and PMF set to Required state is allowed in Release 8.10 because PMF and FT configurations are decoupled. However, in Release 8.5, this configuration invalid. Therefore, upon downgrading to Release 8.5, the WLAN might be disabled.
-
-
Software downgrade guidelines for Release 8.10:
-
If you plan to downgrade the Cisco controller from Release 8.10 software, we recommend you to downgrade to Release 8.5.151.0 or later release to prevent the controller configuration files from being corrupted.
-
If you have configured new country codes in Release 8.10 and if you plan to downgrade to an earlier release, then we recommend that you remove the new country code configurations prior to the downgrade. For more information, see CSCvq91895.
-
-
Before downgrading or upgrading the Cisco Controller to another release check for APs or AP modes support. Ensure that only supported APs are connected and also the APs are moved to supported modes on the release that the controller is upgraded or downgraded to.
-
Legacy clients that require RC4 or 3DES encryption type are not supported in Local EAP authentication.
-
If you downgrade to Release 8.0.140.0 or 8.0.15x.0, and later upgrade to a later release and and also have the multiple country code feature configured, then the configuration file could get corrupted. When you try to upgrade to a later release, special characters are added in the country list causing issues when loading the configuation. For more information, see CSCve41740.
Note
Upgrade and downgrade between other releases does not result in this issue.
-
After downloading the new software to the Cisco APs, it is possible that a Cisco AP may get stuck in an upgrading image state. In such a scenario, it might be necessary to forcefully reboot the controller to download a new controller software image or to reboot the controller after the download of the new controller software image. You can forcefully reboot the controller by entering the reset system forced command.
-
It is not possible to download some of the older configurations from the controller because of the Multicast and IP address validations. See the "Restrictions on Configuring Multicast Mode" section in the Cisco Wireless Controller Configuration Guide for detailed information about platform support for global multicast and multicast mode.
-
When a client sends an HTTP request, the controller intercepts it for redirection to the login page. If the HTTP GET request that is intercepted by the controller is longer than 2000 bytes, the controller drops the packet. Track the Caveat ID CSCuy81133 for a possible enhancement to address this restriction.
-
When downgrading from one release to an earlier release, you might lose the configuration from your current release. The workaround is to reload the previous controller configuration files that are saved in the backup server, or to reconfigure the controller.
-
When you upgrade a controller to an intermediate release, wait until all the APs that are associated with the controller are upgraded to the intermediate release before you install the latest controller software. In large networks, it can take some time to download the software on each AP.
-
You can upgrade to a new release of the controller software or downgrade to an earlier release even if FIPS is enabled.
-
When you upgrade to the latest software release, the software on the APs associated with the controller is also automatically upgraded. When an AP is loading software, each of its LEDs blinks in succession.
-
Controllers support standard SNMP MIB files. MIBs can be downloaded from the software download page on Cisco.com.
-
The controller software that is factory-installed on your controller and is automatically downloaded to the APs after a release upgrade and whenever an AP joins a controller. We recommend that you install the latest software version available for maximum operational benefit.
-
Ensure that you have a TFTP, HTTP, FTP, or SFTP server available for the software upgrade. Follow these guidelines when setting up a server:
-
Ensure that your TFTP server supports files that are larger than the size of controller software image. Some TFTP servers that support files of this size are tftpd32 and the TFTP server within Cisco Prime Infrastructure. If you attempt to download the controller software image and your TFTP server does not support files of this size, the following error message appears:
TFTP failure while storing in flash -
If you are upgrading through the distribution system network port, the TFTP or FTP server can be on the same subnet or a different subnet because the distribution system port is routable.
-
-
The controller Bootloader stores a copy of the active primary image and the backup image. If the primary image becomes corrupted, you can use the Bootloader to boot with the backup image.
With the backup image stored before rebooting, from the Boot Options menu, choose Option 2: Run Backup Image to boot from the backup image. Then, upgrade with a known working image and reboot controller.
-
You can control the addresses that are sent in the Control and Provisioning of Wireless Access Points (CAPWAP) discovery responses when NAT is enabled on the Management Interface, using the following command:
config network ap-discovery nat-ip-only {enable | disable}
The following are the details of the command:
enable —Enables use of NAT IP only in a discovery response. This is the default. Use this command if all the APs are outside the NAT gateway.
disable —Enables use of both NAT IP and non-NAT IP in a discovery response. Use this command if APs are on the inside and outside the NAT gateway, for example, Local Mode and OfficeExtend APs are on the same controller.
Note
To avoid stranding of APs, you must disable the AP link latency (if enabled) before you use the disable option in the config network ap-discovery nat-ip-only command. To disable AP link latency, use the config ap link-latency disable all command.
-
Do not power down the controller or any AP during the upgrade process. If you do this, the software image might get corrupted. Upgrading the controller with a large number of APs can take as long as 30 minutes, depending on the size of your network. However, with the increased number of concurrent AP upgrades supported, the upgrade time should be significantly reduced. The APs must remain powered, and controller must not be reset during this time.
-
After you perform the following functions on the controller, reboot it for the changes to take effect:
-
Enable or disable LAG.
-
Enable a feature that is dependent on certificates (such as HTTPS and web authentication).
-
Add a new license or modify an existing license.
Note
Reboot is not required if you are using Right-to-Use licenses.
-
Increase the priority of a license.
-
Enable HA.
-
Install the SSL certificate.
-
Configure the database size.
-
Install the vendor-device certificate.
-
Download the CA certificate.
-
Upload the configuration file.
-
Install the Web Authentication certificate.
-
Make changes to the management interface or the virtual interface.
-
-
Cisco AireOS 3504 Controller: If the controller has been running for more than 450 days, ensure that you free up the flash memory before downloading the software image to the controller. For more information, see CSCwh98302.
-
Before 8.10.190 release, during the SNMPv3 setup process you could use the same password for both the authentication and the encryption keys on the Cisco AireOS 5520 wireless controller. With the 8.10.190 release, you cannot use the same password for both the keys. This is a functionality that exists in the Cisco Catalyst 9800 series controllers.
Upgrading Cisco Wireless Software (GUI)
Procedure
Step 1 |
Upload your controller configuration files to a server to back up the configuration files.
|
||
Step 2 |
Follow these steps to obtain controller software: |
||
Step 3 |
Copy the controller software file <filename.aes> to the default directory on your TFTP, FTP, SFTP, or USB server. |
||
Step 4 |
(Optional) Disable the controller 802.11 networks.
|
||
Step 5 |
Choose Download File to Controller page. to open the |
||
Step 6 |
From the File Type drop-down list, choose Code. |
||
Step 7 |
From the Transfer Mode drop-down list, choose TFTP, FTP, SFTP, HTTP, or USB. |
||
Step 8 |
Enter the corresponding server details as prompted.
|
||
Step 9 |
Click Download to download the software to the controller. A message indicating the status of the download is displayed.
|
||
Step 10 |
After the download is complete, click Reboot. |
||
Step 11 |
If you are prompted to save your changes, click Save and Reboot. |
||
Step 12 |
Click OK to confirm your decision to reboot the controller. |
||
Step 13 |
If you have disabled the 802.11 networks, reenable them. |
||
Step 14 |
(Optional) To verify that the controller software is installed on your controller, on the controller GUI, click Monitor and view the Software Version field under Controller Summary. |
CIMC Utility Upgrade for 5520 and 8540 Controllers
The AIR-CT5520-K9 and AIR-CT8540-K9 controller models are based on Cisco UCS server C series, C220 and C240 M4 respectively. These controller models have CIMC utility that can edit or monitor low-level physical parts such as power, memory, disks, fan, temperature, and provide remote console access to the controllers.
We recommend that you upgrade the CIMC utility to a version that has been certified to be used with these controllers. Controllers that have older versions of CIMC installed are susceptible to rebooting without being able to access FlexFlash, with the result that the manufacturing certificates are unavailable, and thus SSH and HTTPS connections will fail, and access points will be unable to join. See: CSCvo33873. The recommended versions addresses the vulnerability tracked in CSCvo01180 caveat.
The certified CIMC images are available at the following locations:
Controller | Current CIMC Version | Recommended CIMC Version | Link to Download the CIMC Utility Software Image | ||
---|---|---|---|---|---|
Cisco 5520 Wireless Controller Cisco 8540 Wireless Controller |
2.x |
3.0(4r) |
https://software.cisco.com/download/home/286281345/type/283850974/release/3.0(4r)
|
||
Cisco 5520 Wireless Controller Cisco 8540 Wireless Controller |
3.0(4d) |
3.0(4r) |
https://software.cisco.com/download/home/286281345/type/283850974/release/3.0(4r) |
||
Cisco 5520 Wireless Controller Cisco 8540 Wireless Controller |
4.0(1a) |
4.0(2n) |
https://software.cisco.com/download/home/286281345/type/283850974/release/4.0(2n) |
Current Firmware Version | Upgrade Path to 4.x version |
---|---|
2.x |
You must upgrade to a 3.x version and then upgrade to the recommended 4.x version. |
3.x |
You can upgrade directly to the recommended 4.x version. |
-
For information about upgrading the CIMS utility version 2.x , see the Introduction to Cisco IMC Secure Boot section in the Cisco UCS C-Series Servers Integrated Management Controller CLI Configuration Guide, Release 3.0:
For information about upgrading the CIMS utility version 2.x using webUI , see the Updating the Firmware section https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/sw/gui/config/guide/3_0/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_for_HTML5_Based_Servers_301/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_207_chapter_01101.html#task_C137961E9E8A4927A1F08740184594CA.
Note
When upgrading the firmware using the webUI method, you must select Install Firmware through Remote Server option when prompted in the webUI.
-
For information about upgrading the CIMC utility, see the Updating the Firmware on Cisco UCS C-Series Servers chapter in the Cisco Host Upgrade Utility 3.0 User Guide:
-
Updating Firmware Using the Update All Option
This section mentions specific details when using CIMC utility with Cisco 5520 or 8540 controllers. For general information about the software and UCS chassis, see Release Notes for Cisco UCS C-Series Software, Release 3.0(4) at:
Release Notes for Cisco UCS C-Series Software, Release 4.0(2) at:
Caveat ID | Description |
---|---|
NI-HUU fails to handle the special characters in the password of CIFS remote share |
Caveat ID | Description |
---|---|
SSH weak KeyExchange algorithm [diffie-hellman-group14-sha1] has to be removed |
Interoperability with Other Clients
This section describes the interoperability of controller software with other client devices.
The following table describes the configuration that is used for testing the client devices.
Hardware or Software Parameter | Hardware or Software Configuration Type |
---|---|
Release |
8.10.x |
Cisco Wireless Controller |
Cisco 3504 Wireless Controller |
Access Points |
Cisco 9130, 9120 and 3800 APs |
Radio |
802.11ax (2.4 GHz or 5 GHz), 802.11ac, 802.11a, 802.11g, 802.11n (2.4 GHz or 5 GHz) |
Security |
Open, WPA3-SAE/OWE ( WPA3 Supported Clients), WPA2+WPA3 ( Mixed Mode) PSK (WPA2-AES), 802.1X (WPA2-AES)(EAP-PEAP) |
RADIUS |
Cisco ISE 2.5 |
Types of tests |
Association, Traffic ( TCP/UDP/ICMP) and Roaming between APs |
The following table lists the client types on which the tests were conducted. Client types included laptops, handheld devices, phones, and printers.
Client Type and Name | Driver / Software Version | ||
---|---|---|---|
Wi-Fi 6 Devices (Mobile Phone and Laptop) |
|||
Apple iPhone 11 | iOS 14.1 | ||
Apple iPhone SE 2020 |
iOS 14.1 | ||
Dell Intel AX1650w | Windows 10 ( 21.90.2.1) | ||
DELL LATITUDE 5491 (Intel AX200) | Windows 10 Pro (21.40.2) | ||
Samsung S20 | Android 10 | ||
Samsung S10 (SM-G973U1) | Android 9.0 (One UI 1.1) | ||
Samsung S10e (SM-G970U1) | Android 9.0 (One UI 1.1) | ||
Samsung Galaxy S10+ | Android 9.0 | ||
Samsung Galaxy Fold 2 |
Android 10 | ||
Samsung Galaxy Flip Z |
Android 10 | ||
Samsung Note 20 |
Android 10 | ||
Laptops |
|||
Acer Aspire E 15 E5-573-3870 (Qualcomm Atheros QCA9377) | Windows 10 Pro (12.0.0.832) | ||
Apple Macbook Air 11 inch | OS Sierra 10.12.6 | ||
Apple Macbook Air 13 inch | OS Catalina 10.15.4 | ||
Apple Macbook Air 13 inch | OS High Sierra 10.13.4 | ||
Macbook Pro Retina | OS Mojave 10.14.3 | ||
Macbook Pro Retina 13 inch early 2015 | OS Mojave 10.14.3 | ||
Dell Inspiron 2020 Chromebook |
Chrome OS 75.0.3770.129 |
||
Google Pixelbook Go |
Chrome OS 84.0.4147.136 |
||
HP chromebook 11a |
Chrome OS 76.0.3809.136 |
||
Samsung Chromebook 4+ |
Chrome OS 77.0.3865.105 |
||
DELL Latitude 3480 (Qualcomm DELL wireless 1820) | Win 10 Pro (12.0.0.242) | ||
DELL Inspiron 15-7569 (Intel Dual Band Wireless-AC 3165) | Windows 10 Home (18.32.0.5) | ||
DELL Latitude E5540 (Intel Dual Band Wireless AC7260) | Windows 7 Professional (21.10.1) | ||
DELL XPS 12 v9250 (Intel Dual Band Wireless AC 8260 ) | Windows 10 (19.50.1.6) | ||
DELL Latitude 5491 (Intel AX200) | Windows 10 Pro (21.40.2) | ||
DELL XPS Latitude12 9250 (Intel Dual Band Wireless AC 8260) | Windows 10 Home (21.40.0) | ||
Lenovo Yoga C630 Snapdragon 850 (Qualcomm AC 2x2 Svc) |
Windows 10(1.0.10440.0) |
||
Lenovo Thinkpad Yoga 460 (Intel Dual Band Wireless-AC 9260) | Windows 10 Pro ( 21.40.0) | ||
|
|||
Tablets |
|||
Apple iPad Pro | iOS 13.5 | ||
Apple iPad Air2 MGLW2LL/A | iOS 12.4.1 | ||
Apple iPad Mini 4 9.0.1 MK872LL/A | iOS 11.4.1 | ||
Apple iPad Mini 2 ME279LL/A | iOS 12.0 | ||
Microsoft Surface Pro 3 – 11ac | Qualcomm Atheros QCA61x4A | ||
Microsoft Surface Pro 3 – 11ax | Intel AX201 chipset. Driver v21.40.1.3 | ||
Microsoft Surface Pro 7 – 11ax | Intel Wi-Fi chip (HarrisonPeak AX201) (11ax, WPA3) | ||
Microsoft Surface Pro X – 11ac & WPA3 | WCN3998 Wi-Fi Chip (11ac, WPA3) | ||
Mobile Phones |
|||
Apple iPhone 5 | iOS 12.4.1 | ||
Apple iPhone 6s | iOS 13.5 | ||
Apple iPhone 8 | iOS 13.5 | ||
Apple iPhone X MQA52LL/A | iOS 13.5 | ||
Apple iPhone 11 | iOS 14.1 | ||
Apple iPhone SE MLY12LL/A | iOS 11.3 | ||
ASCOM SH1 Myco2 | Build 2.1 | ||
ASCOM SH1 Myco2 | Build 4.5 | ||
ASCOM Myco 3 v1.2.3 | Android 8.1 | ||
Drager Delta | VG9.0.2 | ||
Drager M300.3 | VG2.4 | ||
Drager M300.4 | VG2.4 | ||
Drager M540 | DG6.0.2 (1.2.6) | ||
Google Pixel 2 | Android 10 | ||
Google Pixel 3 | Android 11 | ||
Google Pixel 3a |
Android 11 |
||
Google Pixel 4 | Android 11 | ||
Huawei Mate 20 pro | Android 9.0 | ||
Huawei P20 Pro | Android 9.0 | ||
Huawei P40 |
Android 10 |
||
LG v40 ThinQ | Android 9.0 | ||
One Plus 8 |
Android 10 |
||
Oppo Find X2 |
Android 10 |
||
Redmi K20 Pro |
Android 10 |
||
Samsung Galaxy S7 | Andriod 6.0.1 | ||
Samsung Galaxy S7 SM - G930F | Android 8.0 | ||
Samsung Galaxy S8 | Android 8.0 | ||
Samsung Galaxy S9+ - G965U1 | Android 9.0 | ||
Samsung Galaxy SM - G950U | Android 7.0 | ||
Sony Experia 1 ii |
Android 10 |
||
Sony Experia xz3 | Android 9.0 | ||
Xiaomi Mi10 |
Android 10 |
||
Spectralink 8744 | Android 5.1.1 | ||
Spectralink Versity Phones 9540 | Android 8.1 | ||
Vocera Badges B3000n | 4.3.2.5 | ||
Vocera Smart Badges V5000 | 5.0.4.30 | ||
Zebra MC40 | Android 5.0 | ||
Zebra MC40N0 | Android Ver: 4.1.1 | ||
Zebra MC92N0 | Android Ver: 4.4.4 | ||
Zebra TC51 | Android 7.1.2 | ||
Zebra TC52 | Android 8.1.0 | ||
Zebra TC55 | Android 8.1.0 | ||
Zebra TC57 | Android 8.1.0 | ||
Zebra TC70 | Android 6.1 | ||
Zebra TC75 | Android 6.1.1 | ||
Printers | |||
Zebra QLn320 Printer | LINK OS 6.3 | ||
Zebra ZT230 Printer | LINK OS 6.3 | ||
Zebra ZQ310 Printer | LINK OS 6.3 | ||
Zebra ZD410 Printer | LINK OS 6.3 | ||
Zebra ZT410 Printer | LINK OS 6.3 | ||
Zebra ZQ610 Printer | LINK OS 6.3 | ||
Zebra ZQ620 Printer | LINK OS 6.3 | ||
Wireless Module |
|||
Intel 11ax 200 |
Driver v21.40.1.3, v21.20.1.1 | ||
Intel AC 9260 |
Driver v21.40.0 | ||
Intel Dual Band Wireless AC 8260 |
Driver v19.50.1.6 |
Key Features Not Supported in Controller Platforms
This section lists the features that are not supported on various controller platforms:
Note |
In a converged access environment that has controllers running AireOS code, High Availability Client SSO and native IPv6 are not supported. |
Key Features Not Supported in Cisco 3504 Wireless Controller
-
Cisco WLAN Express Setup Over-the-Air Provisioning
-
Mobility controller functionality in converged access mode
-
VPN Termination (such as IPsec and L2TP)
Key Features Not Supported in Cisco 5520 and 8540 Wireless Controllers
-
Internal DHCP Server
-
Mobility controller functionality in converged access mode
-
VPN termination (such as IPsec and L2TP)
-
Fragmented pings on any interface
Key Features Not Supported in Cisco Virtual Wireless Controller
-
Cisco Umbrella
-
Software-defined access
-
Domain-based ACLs
-
Internal DHCP server
-
Cisco TrustSec
-
Access points in local mode
-
Mobility or Guest Anchor role
-
Wired Guest
-
Multicast
Note
FlexConnect locally switched multicast traffic is bridged transparently for both wired and wireless on the same VLAN. FlexConnect APs do not limit traffic based on IGMP or MLD snooping.
-
FlexConnect central switching in large-scale deployments
Note
-
FlexConnect central switching is supported in only small-scale deployments, wherein the total traffic on controller ports is not more than 500 Mbps.
-
FlexConnect local switching is supported.
-
-
Central switching on Microsoft Hyper-V deployments
-
AP and Client SSO in High Availability
-
PMIPv6
-
Datagram Transport Layer Security (DTLS)
-
EoGRE (Supported only in local switching mode)
-
Workgroup bridges
-
Client downstream rate limiting for central switching
-
SHA2 certificates
-
Controller integration with Lync SDN API
-
Cisco OfficeExtend Access Points
Key Features Not Supported in Access Point Platforms
This section lists the key features that are not supported on various Cisco Aironet AP platforms. For detailed information about feature support on Cisco Aironet Wave 2 and 802.11ax APs, see:
https://www.cisco.com/c/en/us/td/docs/wireless/access_point/feature-matrix/ap-feature-matrix.html
Key Features Not Supported in Cisco Aironet 1800i, 1810 OEAP, 1810W, 1815, 1830, 1850, 2800, 3800, and 4800 Series APs
Operational Modes |
|
||||
Protocols |
|
||||
Security |
|
||||
Quality of Service |
Cisco Air Time Fairness (ATF)
|
||||
FlexConnect Features |
|
Note |
For Cisco Aironet 1850 Series AP technical specifications with details on currently supported features, see the Cisco Aironet 1850 Series Access Points Data Sheet. |
Key Features Not Supported in Cisco Aironet 1800i, 1810 OEAP, and 1810W Series APs
Operational Modes |
Mobility Express |
FlexConnect Features |
Local AP authentication |
Location Services |
Data RSSI (Fast Locate) |
Key Features Not Supported in Cisco Aironet 1830, 1850, and 1815 Series APs
Operational Modes |
Mobility Express is not supported in Cisco 1815t APs. |
FlexConnect Features |
Local AP Authentication |
Location Services |
Data RSSI (Fast Locate) |
Key Features Not Supported in Mesh Networks
-
Load-based call admission control (CAC). Mesh networks support only bandwidth-based CAC or static CAC
-
High availability (Fast heartbeat and primary discovery join timer)
-
AP acting as supplicant with EAP-FASTv1 and 802.1X authentication
-
AP join priority (Mesh APs have a fixed priority)
-
Location-based services
Key Features Not Supported in Cisco Aironet 1540 Mesh APs
-
Dynamic Mesh backhaul data rate.
Note
We recommend that you keep the Bridge data rate of the AP as auto.
-
Background scanning
-
Noise-tolerant fast convergence
Key Features Not Supported on Cisco Aironet 1560 APs
-
MAC Authentication FlexConnect Local Authentication
-
Noise-tolerant fast convergence
-
Static WEP
Key Features Not Supported on Cisco Catalyst IW6300 Heavy Duty Series AP and 6300 Series Embedded Services AP
-
MAC Authentication FlexConnect Local Authentication
-
Noise-tolerant fast convergence
-
Static WEP
Unfixed and Fixed Issues in Release 8.10.190.0
Open Caveats
Caveat ID Number |
Description |
---|---|
Cisco Aironet 3802 AP is not able to acknowledge EAP frames (EAP-TLS) |
|
Cisco Aironet 2800 and 3800 APs exhibit choppiness during the multicast voice call |
|
Cisco Aironet 2802 AP reloads unexpectedly due to kernel panic |
|
AP does not send Add Traffic Stream (ADDTS) response when Protected Management Frame PMF is enabled |
|
Cisco Catalyst 9120 APs cannot send ACK over the air during EAP negotiation |
|
Controller unexpectedly reloads with snmp_trap_msg_task System crash as observed in the crash file |
|
The client data rate displays incorrectly on the GUI or CLI |
|
Controller drops AP DTLS connection |
|
Cisco Catalyst 9115 Series APs: DFS detection optimization to avoid false DFS detection |
|
Cisco Catalyst 9120 Series AP beacon gets stuck after moving from channel UNII 1 to UNII 2 |
|
C9115/9120 reading /sys/class/thermal/thermal_zone0/temp failed [2]: No such file or directory logs |
|
AP kernel panic crash (PC is at vfp_reload_hw) |
|
Cisco Aironet 3802 series APs reloads unexpectedly on Radio 1 in FlexConnect mode |
|
802.11r retried Auth packet forwarded to controller causes duplicate Auth responses sent to client |
|
Cisco Aironet 2802 series Access Point suddenly drops in transmission power level |
|
Cisco 2802 AP radio0 reloads unexpectedly due to Exception Path |
Resolved Caveats
Caveat ID Number |
Description |
---|---|
WLC sending CAPWAP fragmented packets in out of order sequence when heavy UDP traffic is sent |
|
Unexpected AP reload: PC is at _ZN17CapwapReassembler10next_chunkEP14Writab_H5de9de88a6+0xb4/0xe0 |
|
Cisco 9117 AP radio reloads unexpectedly after disabling MU-MIMO |
|
2802 AP XOR Radio (2.4GHz) shows 40MHz Channel Width on monitoring tools when running 8.10.121 code. |
|
Cisco 9115, 9120 displays too high power on 2.4-GHz |
|
AP running mobility express has kernel Panic crash |
|
COS APs reloads unexpectedly due to dnsmasq-host.service failed on upgrading AireOS WLC above 8.5.x |
|
IPv6 connectivity broken when HA SSO is triggered with AAA override enabled for VLAN |
|
Cisco Wave2 APs sets global config for AP syslog level after reload instead of keeping per-AP config |
|
C9800:"wl:0.7 MFP frame from decrypt failed" messages printed on C9120AX AP console |
|
Cisco 2802 AP reloads unexpectedly on CAPWAPd with WLAN AP service function |
|
Clients behind a WGB facing limited connectivity after a 2nd failover (HA SSO) |
|
Cisco Wave 2 APs not able to negotiate power with Cisco SG350 switches |
|
QoS Priority incorrectly marked with WMM UP 5 when DSCP value is 46 |
|
Cisco 9800 MESH: Cisco 1542 AP does not converge to Cisco 1572 AP |
|
Cisco Wave 2 APs flooding syslog server with lat_client_add failure errors |
|
AP2800/3800/4800/1560/6300 fails to transmit data frame to the client from the radio interface |
|
Fault Tolerance broken in Flex APs due to vendor_set_ccx_elements |
|
Mixed WIFI Mesh: [IOS-RAP + COS-MAP] : IW6300 MAP authentication failure after reboot |
|
Mixed Wi-Fi Mesh: [IOS-RAP + COS-MAP] BA Session establishment errors and iPAD performance issues |
|
APs not forwarding or dropping ARP response when doing Split Tunneling |
|
Controller reloads unexpectedly on debug disable-all command |
|
Cisco 9130AX AP - Not sending M1 over the air |
|
Cisco DNA Center 2.1.2.0 ICAP does not show correct data in auto packet analyzer |
|
Cisco 2802 AP sudden drop in Tx power level |
|
Controller reloads unexpectedly on creating PMK cache |
|
AireOS controller running 8.10.130.0 reloads unexpectedly on SNMPTask consuming 100% CPU |
|
Unable to change AP Country on the Controller's GUI |
|
Object "cLApWlanStatsEntry" SNMPWALK shows the value "0" while traffic is transmitted |
|
Cisco 9130AX AP dropping packets: AP not able to push packet to click module |
|
Cisco Wave 2 and 802.11AX APs crashes due to kernel panic |
|
17.3.2: flex: Suppress "PMK cache was found..." & "Found SSG Device info..." |
|
Mobility Express GUI display issue when using IE11 |
|
Cisco 5520 controller reloads unexpectedly with task name EAP_Framework_0 |
|
Controller reloads unexpectedly on Reaper Reset: Task "spamApTask3" |
|
Tri-radio AP sees its own 11b frames as rogue impersonation |
|
AP3800 randomly not sending traffic to client queue 0 after dot1x session-timeout due to CSCvo91525 |
|
Cisco switches connected to Wave2 APs generate CDP-4-DUPLEX_MISMATCH |
|
Controller reloads unexpectedly at NFV9_Task |
|
Standby WLC sends ARP requests using the management interface IP address |
|
%SAFEC-3-SAFEC_ERROR appearing on WLC syslogs, causing APs to disassociate from the controller |
|
C9115, C9120 APs not processing protected NDP from other AP models except for NDP Tx from C9115 AP |
|
Cisco 2800 AP running release 8.10.130 reloads unexpectedly due to FIQ/NMI reset |
|
Mobility Express - No client to client communication after roaming when AVC is enabled |
|
GUI FlexConnect ACLs - URL Rules can be configured > 20 and "remove" issue from 21st URL Rule |
|
Cisco 5520 controller running 8.5.164.215 facing memory leak issues |
|
Cisco 9120AX APs: AP stops using LSC and uses only MIC |
|
Controller does not reflect IPv4 address for random clients |
|
ICAP chart shows increasing Rx average data rate when the most recent data rate is flat |
|
Rogue detection logic causing high CPU on C9130AX AP without any clients connected to it |
|
Users are required to configure both SNMP RO and RW from UI |
|
Cisco 2700 AP flooding GARPs with its own IP addresses dual-stack scenario 9800 17.3.2 |
|
IPv6 only network with multiple IPv6 address causing zero MAC, causing AP unable to join situation |
|
Unable to make changes on IW3702 AP flex+ bridge mode using WLC GUI |
|
Some clients not connecting to 2.4-GHz due to Wrong channel advertising on C9100 APs |
|
C9120: Kernel Panic at select_task_rq_fair+0x2c/0x7d8 when running 17.3.2.32 |
|
Cisco Flex group configurations gets appended with junk chars in show tech-support with multi words |
|
Cisco 1852 APs switch to DHCP even if static-ip failover is disable |
|
When running debug client <mac address> logs are flooded with IPContext |
|
C9120AX APs stop forwarding some Moxa WGB client packet via CAPWAP |
|
Cisco Wave 2 AP frames randomly stuck in buffer with U-APSD enabled on 17.3.2 |
|
C1850 APs LAG AP reflect Wired0 traffic out of Wired1 when using LAG + flexconnect + local switching |
|
Cisco Wave 1 devices cannot reach internet when connected to OEAP personal SSID |
|
RF Profile parameters are not pushed for optimized roaming |
|
IRCM tunnel between C9800 and AireOS fails to recover for 30+ minutes |
|
C9120AX APs disconnecting from 9800 after receiving CAPWAP payload with exclusion-list client list |
|
C9115, 9120 APs use the wrong TID when responding to Block Ack Requests |
|
Cisco 9120AX, 9115AX, 9105AX APs drop upstream traffic (various types) with data DTLS enabled |
|
1562 mesh ap not able to join with FIPS enabled |
|
ARP queries flood due to low value of BSS Max Idle Period |
|
Cisco 5520 controllers in HA reload unexpectedly within minutes of each other |
|
Cisco controller reloads unexpectedly with task name "Dot1x_NW_MsgTask_4" |
|
C9130AX AP tri-radio enabled by manual dual radio assignment mode makes HE disabled on slot1 |
|
Cisco 9120AX AP TFTP transfer failed |
|
Cisco 8540 Wireless Controller reloads unexpectedly |
Related Documentation
Communications, Services, and Additional Information
-
To receive timely, relevant information from Cisco, sign up at Cisco Profile Manager.
-
To get the business impact you’re looking for with the technologies that matter, visit Cisco Services.
-
To submit a service request, visit Cisco Support.
-
To discover and browse secure, validated enterprise-class apps, products, solutions, and services, visit Cisco DevNet.
-
To obtain general networking, training, and certification titles, visit Cisco Press.
-
To find warranty information for a specific product or product family, access Cisco Warranty Finder.
Cisco Bug Search Tool
Cisco Bug Search Tool (BST) is a gateway to the Cisco bug-tracking system, which maintains a comprehensive list of defects and vulnerabilities in Cisco products and software. The BST provides you with detailed defect information about your products and software.
Documentation Feedback
To provide feedback about Cisco technical documentation, use the feedback form available in the right pane of every online document.