The Cisco IOS image is stored as a bin file in a directory that is named with the Cisco IOS release. A subdirectory contains the files needed for web management. The image is stored on the compact flash memory card.

You can use the show version privileged EXEC command to see the software version that is running on your switch. The second line of the display shows the version.

You can also use the dir filesystem: privileged EXEC command to see the directory names of other software images stored in flash memory. For example, use the dir flash: command to display the images in the flash memory.

The upgrade procedures in these release notes describe how to perform the upgrade by using a combined tar file. This file contains the Cisco IOS image file and the files needed for the embedded device manager. You must use the combined tar file to upgrade the switch through Express Setup. To upgrade the switch through the command-line interface (CLI), use the tar file and the archive download-sw privileged EXEC command.

The following table lists the filenames for this software release.

Note: If you download the IP services image and plan to use Layer 3 functionality, you must use the Switch Database Management (SDM) routing template. To determine the currently active template, enter the show sdm prefer privileged EXEC command. If necessary, enter the sdm prefer global configuration command to change the SDM template to a specific template. For example, if the switch uses Layer 3 routing, change the SDM template from the default to the routing template. You must reload the switch for the new template to take effect.

Table 1. Cisco IOS Software Image Files

File Name	Description
cgs2520-ipserviceslmk9-tar.152-8.E7.tar	CGS 2520 IP services image file
cgs2520-lanbaselmk9-tar.152-8.E7.tar	CGS 2520 LAN base image file
c2020-universalk9-tar.152-8.E7.tar	ESS 2020 universal image file
ie2000-universalk9-tar.152-8.E7.tar	IE 2000 universal image file
ie2000u-ipserviceslmk9-tar.152-8.E7.tar	IE 2000U IP services image file
ie2000u-lanbaselmk9-tar.152-8.E7.tar	IE 2000U LAN base image file
grwicdes-ipserviceslmk9-tar.152-8.E7.tar	ESM IP services image file
grwicdes-lanbaselmk9-tar.152-8.E7.tar	ESM LAN base image file
ie4000-universalk9-tar.152-8.E7.tar	IE 4000 Universal image file
ie4010-universalk9-tar.152-8.E7.tar	IE 4010 Universal image file
ie5000-universalk9-tar.152-8.E7.tar	IE 5000 Universal image file

Before upgrading your switch software, make sure that you archive copies of both your current Cisco IOS release and the Cisco IOS release to which you are upgrading. Keep these archived images until you have upgraded all devices in the network to the new Cisco IOS image and verified that the new Cisco IOS image works properly in your network.

Cisco routinely removes old Cisco IOS versions from Cisco.com. See Product Bulletin 2863 for information:

http://www.cisco.com/en/US/prod/collateral/iosswrel/ps8802/ps6969/ps1835/prod_bulletin0900aecd80281c0e.html

You can copy the bin software image file on the flash memory to the appropriate TFTP directory on a host by using the copy flash: tftp: privileged EXEC command.

Note: Although you can copy any file on the flash memory to the TFTP server, it is time consuming to copy all of the HTML files in the tar file. We recommend that you download the tar file from Cisco.com and archive it on an internal host in your network.

You can also configure the switch as a TFTP server to copy files from one switch to another without using an external TFTP server by using the tftp-server global configuration command.

This procedure is for copying the combined tar file to the switch. You copy the file to the switch from a TFTP server and extract the files. You can download an image file and replace or keep the current image.

Note: Make sure that the compact flash card is in the switch before downloading the software.

To download software, follow these steps:

1. See Deciding Which Files to Use to identify the file that you want to download.

2. Download the software image file. If you have a SMARTnet support contract, go to this URL, and log in to download the appropriate files:

   http://software.cisco.com/download/navigator.html

   For example, to download the image for an IE 2000 switch, select Products > Switches > Industrial Ethernet Switches > Cisco Industrial Ethernet 2000 Series Switches, then select your switch model. Select IOS Software for Software Type, then select the image you want to download.

3. Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP server is properly configured.

   For more information, see the “Assigning the Switch IP Address and Default Gateway” chapter in the applicable document for your switch as listed in Table 3.

4. Log into the switch through the console port or a Telnet session.

5. (Optional) Ensure that you have IP connectivity to the TFTP server by entering this privileged EXEC command:

   Switch# ping tftp-server-address

   For more information about assigning an IP address and default gateway to the switch, see Table 3.

6. Download the image file from the TFTP server to the switch.

   If you are installing the same version of software that currently exists on the switch, overwrite the current image by entering this privileged EXEC command:

   Switch# archive download-sw /overwrite /reload tftp://location /directory /image-name.tar

   The command above untars/unzips the file.The system prompts you when it completes successfully.

   • The /overwrite option overwrites the software image in flash memory with the downloaded one.

   If you specify the command without the /overwrite option, the download algorithm verifies that the new image is not the same as the one on the switch Flash device. If the images are the same, the download does not occur. If the images are different, the old image is deleted, and the new one is downloaded. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.

   • The /reload option reloads the system after downloading the image unless the configuration has been changed and not saved.

   • For // location, specify the IP address of the TFTP server. or hostname.

   • For /directory/image-name.tar, specify the directory and the image to download. Directory and image names are case sensitive. The directory is for file organization and it is generally a tftpboot/user-ID path.

   This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite the image on the switch:

   Switch# archive download-sw /overwrite tftp://198.30.20.19/image-name.tar

   You can also download the image file from the TFTP server to the switch and keep the current image by replacing the /overwrite option with the /leave-old-sw option. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.

This procedure is for copying the combined tar file to the switch. You copy the file to the switch from a TFTP server and extract the files. You can download an image file and replace or keep the current image.

To download software, follow these steps:

1. Refer to Deciding Which Files to Use to identify the file that you want to download.

2. Download the software image file. If you have a SMARTnet support contract, go to the URL below and log in to download the appropriate files.

   http://software.cisco.com/download/navigator.html

   For example, to download the image for a Connected Grid 10-Port Ethernet Switch Module Interface Card, select Products > Cisco Interfaces and Modules > Connected Grid Modules > Connected Grid 10-Port Ethernet Switch Module Interface Card. Select IOS Software for Software Type, then select the image you want to download.

   Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP server is properly configured. For more information, see the “Assigning the Switch IP Address and Default Gateway” chapter in the applicable document listed in Table 3 Methods for Assigning IP Information, page 8.

3. Copy the image to the appropriate TFTP directory on the workstation, and make sure that the TFTP server is properly configured.

4. Log in to the switch through the console port or a Telnet session.

5. (Optional) Ensure that you have IP connectivity to the TFTP server by entering this privileged EXEC command:

   Switch# ping tftp-server-address

6. Download the image file from the TFTP server to the switch.

   If you are installing the same version of software that currently exists on the switch, overwrite the current image by entering this privileged EXEC command:

   Switch# archive download-sw /overwrite tftp: //location /directory /image-name.tar

   The command above untars/unzips the file.The system prompts you when it completes successfully.

   • The /overwrite option overwrites the software image in flash memory with the downloaded one.

   If you specify the command without the /overwrite option, the download algorithm verifies that the new image is not the same as the one on the switch Flash device. If the images are the same, the download does not occur. If the images are different, the old image is deleted, and the new one is downloaded. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.

   • The /reload option reloads the system after downloading the image unless the configuration has been changed and not saved.

   • For // location, specify the IP address of the TFTP server. or hostname.

   • For /directory/image-name.tar, specify the directory and the image to download. Directory and image names are case sensitive. The directory is for file organization and it is generally a tftpboot/user-ID path.

   This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite the image on the switch:

   Switch# archive download-sw /overwrite tftp://198.30.20.19/image-name.tar

   You can also download the image file from the TFTP server to the switch and keep the current image by replacing the /overwrite option with the /leave-old-sw option. If there is not enough space to install the new image and keep the current running image, the download process stops, and an error message displays.

7. After the download and the untar are complete, power cycle the CGR2010.

You can assign IP information to your switch using the methods shown in the following table.

Table 2. Methods for Assigning IP Information

Method	Platform	Document
Express setup program	IE2000	Cisco IE 2000 Switch Hardware Installation Guide
	ESM	Connected Grid Ethernet Switch Module Interface Card Getting Started Guide
	IE4000	Cisco IE 4000 Switch Hardware Installation Guide
	IE4010	Cisco IE 4010 Switch Hardware Installation Guide
	IE5000	Cisco IE 5000 Hardened Aggregator Hardware Installation Guide
CLI-based setup program	ESS2020	Cisco Embedded Service 2020 Series Software Configuration Guide
	IE2000	Cisco IE 2000 Switch Hardware Installation Guide
	IE2000U	Cisco IE 2000U Switch Hardware Installation Guide
	CGS2520	Cisco CGS 2520 Hardware Installation Guide
	ESM	Cisco CGS 2520 Hardware Installation Guide Note: The Cisco CGS 2520 Hardware Installation Guide serves as CLI-based Setup reference for the ESM.
	IE4000	Cisco IE 4000 Switch Hardware Installation Guide
	IE4010	Cisco Industrial Ethernet 4000, 4010 and 5000 Switch Software Configuration Guide
	IE5000	Cisco IE 5000 Hardened Aggregator Hardware Installation Guide
DHCP-based autoconfiguration	ESS2020	Cisco Embedded Service 2020 Series Software Configuration Guide
	IE2000	Cisco IE 2000 Series Switch Software Configuration Guide
	IE2000U	System Management Software Configuration Guide for Cisco IE 2000U and Connected Grid Switches
	CGS2520	CGS 2520 Switch Software Configuration Guide
	ESM	Cisco Connected Grid Ethernet Switch Module Interface Card Software Configuration Guide
	IE4000	Cisco Industrial Ethernet 4000 Series Switch Software Configuration Guide
	IE4010	Cisco Industrial Ethernet 4000, 4010 and 5000 Switch Software Configuration Guide
	IE5000	Cisco IE 5000 Hardened Aggregator Hardware Installation Guide
Manually assigning an IP address	IE2000	Cisco IE 2000 Series Switch Software Configuration Guide
	IE2000U	System Management Software Configuration Guide for Cisco IE 2000U and Connected Grid Switches
	CGS2520	CGS 2520 Switch Software Configuration Guide
	ESM	Cisco Connected Grid Ethernet Switch Module Interface Card Software Configuration Guide
	IE4000	Cisco Industrial Ethernet 4000 Series Switch Software Configuration Guide
	IE4010	Cisco Industrial Ethernet 4000, 4010 and 5000 Switch Software Configuration Guide
	IE5000	Cisco IE 5000 Hardened Aggregator Hardware Installation Guide

Follow these steps to reload a new GRWIC module with an old Cisco IOS image matching the old FPGA file.

1. Load the 15.2(8)E3 image on the GRWIC that has the new SPI Flash component.

2. Enter

   fpga_upgrade flash <filename>

   to program the new SPI flash of the new GRWIC with the user specified FPGA file at the specified path as shown in the following example:

   Switch#fpga_upgrade?
   flash: File to be upgraded
   nvram: File to be upgraded
   obfl0: File to be upgraded
   Switch#fpga_upgrade flash:grwicdes-ipservicesk9-mz.152-4.EA5/fpga
   System will reload after the FPGA upgrade/downgrade.
   Do you want to proceed? [yes/no]: yes
   FPGA Multiboot: new image size 0x00212B68
   FPGA Multiboot: new image version 0x00030700
   FPGA Multiboot: new image date 10-4-2013 (0x000A27DD)
   Checking for FPGA upgrade.. (flash:grwicdes-ipservicesk9-mz.152-4.EA5/fpga)
   FPGA Multiboot: running image rev: 0x00030800
   FPGA Multiboot: running image date: 0x000C67E2
   Upgrading/downgrading FPGA from 0x00030800 to 0x00030700
   Erasing sectors...................................
   Writing fpga image.................................
   System is resetting..
   Received FPGA upgrade request for module GRWIC-D-ES-2S-8PC on slot 0
   Current Running Image:
   Release Status: Official Release Image
   Major Version: 3
   Minor Version: 8
   Debug Version: 0
   Version Date: 2018-12-12
   Upgrade Image:
   Release Status: Official Release Image
   Major Version: 3
   Minor Version: 7
   Debug Version: 0
   Version Date: 2013-10-4
   FPGA image upgrade for slot 0 succeed!!!
   Current Running Image:
   Release Status: Official Release Image
   Major Version: 3
   Minor Version: 7
   Debug Version: 0
   Version Date: 2013-10-4
   Using driver version 3 for media type 1
   Base ethernet MAC Address: 54:a2:74:3e:02:80
   Xmodem file system is available.
   The password-recovery mechanism is enabled.
   Initializing Flash...
   mifs[2]: 13 files, 1 directories
   mifs[2]: Total bytes : 1806336
   mifs[2]: Bytes used : 886272
   mifs[2]: Bytes available : 920064
   mifs[2]: mifs fsck took 1 seconds.
   mifs[3]: 188 files, 24 directories
   mifs[3]: Total bytes : 63092736
   mifs[3]: Bytes used : 54162944
   mifs[3]: Bytes available : 8929792
   mifs[3]: mifs fsck took 26 seconds.
   ...done Initializing Flash.
   done.

3. After the FPGA upgrade/downgrade for the old Cisco IOS (the required IOS version) is completed, load the old Cisco IOS as shown in the following example:

   switch#conf t
   switch(config)#boot system
   flash:/grwicdes-ipservicesk9-mz.152-4.EA5/grwicdes-ipservicesk9-mz.152-4.EA5.bin
   switch(config)#end
   switch#wr mem
   switch#reload

The Bug Search Tool (BST), which is the online successor to Bug Toolkit, is designed to improve the effectiveness in network risk management and device troubleshooting. The BST allows partners and customers to search for software bugs based on product, release, and keyword, and aggregates key data such as bug details, product, and version. The tool has a provision to filter bugs based on credentials to provide external and internal bug views for the search input.

To view the details of a caveat listed in this document:

1. Access the BST (use your Cisco user ID and password) at https://tools.cisco.com/bugsearch/.

2. Enter the bug ID in the Search For: field

Table 3. Open Caveats in Cisco IOS Release 15.2(8)E7

Bug ID	Headline
CSCvu66982	Delay in loading WebUI on Low-end Devices when type 9 encryption is enabled (IE2000, IE3000)

Table 4. Resolved Caveats in Cisco IOS Release 15.2(8)E7

Bug ID	Headline
CSCwk98025	IE-2000 switches cannot capture IGMP membership reports in SPAN capture.
CSCwj42886	SFTP/SCP file transfer fails on ie5000 switch.
CSCwj96922	With switchport nonegotiate- vlan tag is added, without switchport nonegotiate- vlan tag is removed.
CSCwk65617	FPGA SPAN-TS image 0.2.3.E image with 10G SCP issue RTL fix.
CSCwm57387	Add below command outputs as part of the IE5k show tech-support.
CSCve77011	SSL handshake failure when validating certification with name-constraints.