Use your Cisco.com login credentials to obtain the Cisco ASA Device Package software image from:

https://software.cisco.com/download/release.html?mdfid=283123066&flowid=22661&softwareid=286279676

Starting with release 1.2(7.8), there are two versions of the Cisco ASA Device Package software for ACI:

• Cisco ASA Device Package software for ACI. This version allows you to configure many important features of the ASA from the APIC, including (but not limited to) the following:

  • Interface

  • Routing

  • Access-list

  • NAT

  • TrustSec

  • Application inspection

  • NetFlow

  • High availability

  • Site-to-site VPN

• Cisco ASA Device Package Fabric Insertion software for ACI. This version contains the following subset of features of the original version:

  • Interface

  • Dynamic routing

  • Static routing

Cisco ASA Device Package software supports only the version of APIC that it is shipped with.

The following table lists the supported versions of the Cisco ASA software for each of the supported platforms.

For instructions on how to install the device package, see the respective version of the Cisco ASA Quick Start Guide for APIC Integration hyperlinked on the Software Download page.

Note	To upgrade from an older to a newer version, you do not need to remove the previous software package if your APIC release has the fix for CSCuv4353. Otherwise, remove the older version from the APIC before installing the newer version.

As a registered Cisco.com user, sign in to view more information about each bug or caveat using the Cisco Bug Search Tool.

• The ASAv does not support multiple context mode.

• ACE with dynamic EPG requires ASA image 9.3.2 or newer.

Use this workaround for caveat CSCuw0342:

Symptom: The Policy Manager crashes when the l3Out that is used for BGP peering for the service appliance has an incomplete configuration (CSCuw03425).

Conditions: The l3Out used for BGP peering for the service appliance is missing l3extRsNodeL3OutAtt.

Workaround: Make sure that the l3Out contains l3extRsNodeL3OutAtt. This problem will be fixed in a subsequent release.

The following shows the BGP XML example with l3extRsNodeL3OutAtt:

<polUni>
<fvTenant name="tenant1">
<l3extOut name="StaticExternal">
<l3extLNodeP name="bLeaf-101">
<l3extRsNodeL3OutAtt tDn="topology/pod-1/node-101" rtrId="190.0.0.11">
<ipRouteP ip="50.50.50.0/24">
<ipNexthopP nhAddr="40.40.40.102/32"/>
</ipRouteP>
</l3extRsNodeL3OutAtt>
<l3extLIfP name="portIf">
<l3extRsPathL3OutAtt tDn="topology/pod-1/paths-101/pathep-[eth1/15]" ifInstT="ext-svi" encap="vlan-3843" addr="40.40.40.100/28" mtu="1500"/>
</l3extLIfP>
</l3extLNodeP>
<l3extInstP name="ExtInstP">
<l3extSubnet ip="50.50.50.0/24" scope="export-rtctrl"/>
</l3extInstP>
<l3extRsEctx tnFvCtxName="tenant1ctx1"/>
</l3extOut>
</fvTenant>
</polUni>

Use this workaround for caveat CSCvd65130:

Symptom: When cluster interfaces are changed under lif configuration for a deployed graph in bridge mode, the new interface might not get updated correctly on the ASA.

Conditions: When changes are made to the ASA device cluster interface configuration.

Workaround: Detach the graph from the contract before making any device changes and then attach it.

Use this workaround for caveat CSCvd68860:

Symptom: When a second or subsequent graph is deployed on a new set of cluster interfaces in an ASA in bridged mode, the user might see cluster interfaces not configured under the correct bridge-group. This results in a configuration issue which creates a conflict with existing cluster interfaces using the default names in the ASA.

Conditions: Graph deployment using a new set of cluster interfaces with default interface names in an ASA in bridged mode.

Workaround: Rename the cluster interface name under Interface Related Configuration in graph parameters while configuring the graph.

Use this enhancement feature for caveat CSCvb90258:

Symptom: The ASA Fabic Insertion (FI) Device Package (DP) does not support saving configuration out-of-band.

Conditions: The ASA-FI-DP only supports routing and interface configuration. It does not support the configuration of security policy binding commands, such as access-group and nat, to the service graph. To assign a security policy to a service graph, you must manually configure the setup. In the case of rerendering a service graph after removing it, you must manually reconfigure the bindings.

Solution: This enhancement feature enables you to save the security policy binding commands to a file, which the ASA-FI-DP can apply after the service graph is reattached.

XML: A folder named SecurityPolicyAssignment has been added under vnsMFunc which enables you to enter a name for the configuration that has the security policy to assign to the service graph.

<vnsMFunc name="Firewall">
<vnsMFolder key="ExIntfConfigRelFolder" dispLabel="External Interface Configuration" 
description="A list of additional interface parameters for external connector"...>
<vnsMFolder key="InIntfConfigRelFolder" dispLabel="Internal Interface Configuration" 
description="A list of additional interface parameters for internal connector" ...>
<vnsMConn name="external" ...>
<vnsMConn name="internal" ...>
 <vnsMFolder key="SecurityPolicyAssignment"
   dispLabel="Security Policy Assignment"
   description="Assign the security policy in the named file to the service-graph">
  <vnsMParam key="ConfigFile"
    dispLabel="Configuration File"
    dType="str"
    description="Specify the name of the file that contains the out of band configuration specific to the service-graph"/>
  </vnsMFolder>
 </vnsMFunc>

APIC:

• If the file is on the ASA, enter the name of the file.

• If the file is on a TFTP server, enter: tftp://<ip-address>/<filename>

• If the file is on an FTP server, enter: ftp://<ip-address>/<filename>

The contents of the file should be commands that you must enter out-of-band that reference the interfaces used in the service graph. For example:

access-group <acl-name> [in|out] interface <nameif>
nat (<nameif>, <nameif>) …
service-policy <policy-name> interface <nameif>
crypto map <map-name> interface <nameif>
crypto ike2 enable <nameif>

Here's an example of such a file for a service graph with interfaces externalInt and internalInt:

access-group access-group external_access_acl in interface externalInt
nat (internalInt,externalInt) source static real_obj mapped_obj
nat (internalInt,externalInt) source dynamic any mapped_obj interface

Commands that do not reference an interface should not be part of the file because they're not removed when you remove the service graph. Examples of such commands include:

access-list
object network
object service
object-group network
object-group service

• Cisco ACI Fundamentals

• Cisco ACI Security Solution

• Cisco APIC Layer 4 to Layer 7 Services Deployment Guide

• Cisco APIC Product Support

• Cisco ASA Series Roadmap

• Cisco Firepower Management Center