Device Manager, Release 12.1.3

Name

Field Replaceable Unit (FRU) name.

ModelName

Model name identifier.

SerialNumber

Primary and secondary serial numbers.

HardwareRevision

Hardware revision.

SoftwareRevision

The release version of Cisco NX-OS software.

Alias

Alias name as specified by a network manager.

AssetID

User-assigned asset tracking identifier as specified by a network manager.

Name

Module description.

Module

Module name identifier.

OperStatus

Module’s operational state.

Reset

Click to reboot the module.

RateModeOverSubscriptionLimit

Select this option to control the restriction on the oversubscription ratio on modules that support it. By default, the restriction is enabled. If you disable this option, all the interfaces on the module are capable of operating at maximum admin speed, regardless of the available bandwidth.

BandwidthFairnessConfig

Select this option to control bandwidth fairness on modules that support it. By default, bandwidth fairness is enabled.

BandwidthFairnessOper

Shows if bandwidth fairness is enabled or disabled. By default, bandwidth fairness is enabled.

X2 xcvrFrequency Config

Specifies the transceiver frequency of the module.

ResetReasonDescription

Why module was last reset.

Local Switching Mode

Shows the status of the local switching modules.

StatusLastChangeTime

When OperStatus was changed.

Power Admin

Allows you to power on and off the Field Replaceable Unit (FRU).

Power Oper

Field Replaceable Unit (FRU) operational power state.

Current

Current supplied by the Field Replaceable Unit (FRU).

Name

Power supply location.

TotalPowerAvailable

Shows the available power. In combined mode, the total available power is twice the lesser of the two power supplies.

Redundant/Combined

Select to determine how the power supplies are configured. Redundant mode provides a backup power supply if one should fail, but the total power available is less.

ModelName

The model identifier.

OperStatus

Operational power state.

TotalAvailable

Total power available for power supply usage. When Mode is redundant, the total power available will be the lesser power capacity of the power supplies. When Mode is combined, the total power available will be twice the lesser of the power capacities of the operating power supplies.

TotalReserved

Total current drawn by powered-on FRUs

Name

Sensor location.

Threshold Major

Major temperature threshold.

Threshold Minor

Minor temperature threshold.

Current

Most recent measurement seen by the sensor.

Status

The present operational status of the sensor.

Name

Fan location.

ModelName

The model identifier.

OperStatus

The current operating status.

Description

A description of the switch and software.

UpTime

The time since the network management portion of the system was last re-initialized.

Name

An administratively-assigned name for this switch.

Location

The physical location of this switch (e.g., `telephone closet, 3rd floor').

Contact

The contact person for this switch, together with information on how to contact this person.

SwitchWWN

The World-Wide Name of this switch.

ClockDateAndTime

The current local date and time for the system. Setting this is equivalent to setting an automated clock and calendar.

TimeZone

The current local time zone for the system. The time zone must be entered in the format GMT, which is the number of hours difference between your time zone and GMT (Greenwich Mean Time).

ProcessorRAM

Total number of bytes of RAM available on the Processor.

NVRAM

Total number of bytes of NVRAM in the entity.

NVRAMUsed

Number of bytes of NVRAM in use.

FIPSModeActivation

Enable or disable FIPS mode on the device. FIPS 140-2 is a set of security requirements for cryptographic modules and it details the U.S. Government requirements for cryptographic modules. A module will comprise both hardware and software such as a data center switching or routing module. The module is said to be in FIP- enabled mode when a request is recieved to enable the FIPS mode and a set of self-tests are successfully run in response to the request. If the self-tests fail, then an appropriate error is returned.

CPUUtilization

The average utilization of CPU on the active supervisor.

MemoryUtilization

The average utilization of memory on the active supervisor.

FlashPartitionSize

Flash partition size.

FlashPartitionFreeSpace

Free space within a Flash partition.

Status

The overall status of the switch.

Vendor

Switch vendor’s name, such as Cisco, McData, or Brocade.

Model

Switch model name, such as MDS 9134 or MDS 9124.

Release

Switch software version.

NumFCPorts

Number of physical FC ports in the switch.

WWN

MAC address for the Ethernet VDCs that are discovered.

VDCId

Unique IDs for the Ethernet VDCs that are discovered.

FCoE Enabled

If true, FCoE is enabed for the Ethernet VDCs that are discovered.

From Switch

The source switch of the link.

From Interface

The port index of source E_port of the link.

To Switch

The switch on the other end of the link.

To Interface

The port index of destination E_port of the link.

Status

The operational status of the link.

NPIV (Core)

The NPIV core switch.

F Port

The connected F Port on the NPIV core switch.

NPV

NPV Switch.

NP Port

The connected port on the NPV switch.

Status

The operational status of the link.

Field

Description

Description

An alias name for the interface, as specified by a network manager. For Port Channel and FCIP, this field will always show members if they are available. For FCIP, this field will show compress if compressed.

VSAN(s)

VSAN membership.

Mode

Operating mode of the port> (See Legend).

Connected To

Attached port. This could be a host, storage, or switch port.

Speed

Maximum bandwidth in Gbps.

Rx

One of the following: Utilization % Number of Bytes Number of Frames Average Frame Size

Rx Comp

The IP Copmression ratio for received packets on the FCIP device.

Tx

One of the following: Utilization % Number of Bytes Number of Frames Average Frame Size

Tx Comp

The IP Copmression ratio for transmitted packets on the FCIP device

Errors

Total number of Rx and Tx errors on the interface. Types of Rx errors include CRC errors, fragmented framed, unsupported class frames, runt frames, jabber frames, and giant Frames. Types of Tx errors are generally CRC errors, but these are rare. If the Errors field is not empty, there are probably Rx errors. For a more detailed breakdown of the error count, check the Monitor dialog box for appropriate interface.

Discards

Total number of Rx and Tx discards on the interface. Rx frames discarded are generally due to protocol errors. On rare occasions, a frame is received without any hardware errors, but a filtering rule set for the MAC address discards the frame due to a mismatch. Discarded Tx frames can be timeout frame discards (port is offline or not up), or timeout frames that are not sent back to the supervisor (class F/2 frames). If the Discards field is not empty, it is probably due to timeout frames.

Log

If checked, writes the record into the message log on each poll interval.

Enclosure Name

The name of the enclosure.

Alias

The device alias of this entry.

Port WWN

The assigned PWWN for this host.

FcId

The FC ID assigned for this host.

Link Status

The operational status of the link.

Serial Number

Serial number.

Model

Model name.

Firmware Ver

The version of the firmware executed by this HBA.

Driver Ver

The version of the firmware executed by this HBA.

Information

The information list corresponding to this HBA.

Switch Interface

Interface on the switch that is connected with the end device.

IP Address

The IP address of the enclosure.

Elem. Mgr Use HTTP

Use HTTP to launch the local enclosure.

Elem. Mgr URL/Path

Use a URL to launch the local enclosure

Device Type

If host, it is HBA. If storage, it is the SCSI target.

Vendor

If host, it is HBA. If storage, it is the SCSI target.

Model

If host, it is HBA. If storage, it is the SCSI target.

Firmware Ver

The version of the firmware executed by this HBA.

Driver Ver

The version level of the driver software controlling this HBA.

OS

The type and version of the operating system controlling this HBA

Other Info

The information list corresponding to this HBA.

Retry Requests # time(s) after #sec timeout

The number of retries to be attempted after time out (seconds).

Enable Status Polling

Check to enables status polling in every (specified number of) seconds

Trace SNMP packets in Message Log

Check to enable tracing SNMP packets in the message log.

Register for Events after Open, listen on Port 1163

Check to automatically register for events.

Show WWN Vendor

Check to enable showing the WWN vendor name.

Show Timestamps as Date/Time

Check for displaying the time stamp in the Date/Time format.

Telnet Path

Path to the telnet client.

Use Secure Shell instead of Telnet

Check to use secure shell.

CLI Session Timeout

Time interval for the CLI session (in seconds). Enter '0' to disable CLI timeout.

Show Tooltips in Physical View

Check to show tooltips.

Label Physical View Ports with

Export Table

Switch

Name of the switch hosting this virtual interface group (VIG).

VIG Id

Virtual interface group identifier.

Bound Eth Interface

Physical Ethernet interface associated with this VIG.

Virtual Eth Interfaces

The virtual Ethernet interface bound to this VIG.

Virtual FC Interfaces

The virtual FC interface bound to this VIG.

Operational Status

The current operational state of the VIG.

CreationTime

Date and time when the VIG was created.

Switch

Name of the switch hosting this interface.

Interface

Interface name.

Description

Text description of the interface as specified by a network manager.

VIG Id

Virtual interface group to which this virtual FC interface is bound.

Bind Type

The type of interface associated with this virtual FC interface - physical Ethernet interface or MAC address of the FCoE Node (ENode).

Bind Interface

Physical Ethernet interface or Ethernet port channel associated with this virtual FC interface.

Bind MACAddress

MAC address of an FCoE Node (ENode) or a remote Fibre Channel Forwarder (FCF) identified by the virtual FC interface.

FCF Priority

The FCoE Initialization Protocol (FIP) priority value advertised by the FCF to ENodes.

VSAN ID Port

VSAN ID to which this interface is statically assigned.

VSAN Id Dynamic

Index of the VSAN to which this interface is statically assigned.

Mode Admin

The port mode configured by the user. Virtual FC interfaces support only fabric port (F Port) mode.

Rate Mode

Specifies the interface as dedicated mode or shared mode.

Speed Oper

Operational speed.

Mode Oper

The current operating mode of the port.

Speed Admin

The port speed configured by the user.

Status Service

Specifies whether the interface is in service or out of service.

Status Admin

The desired state of the interface.

Status Oper

The current operational state of the interface.

Status FailureCause

The cause of current operational state of the port.

Status LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

Switch

Name of the switch hosting this interface.

Interface

Interface name.

Description

Text description of the interface as specified by a network manager.

VIG Id

Virtual interface group to which this virtual interface is bound.

Bound Eth Interface

Physical Ethernet interface associated with this virtual Ethernet interface.

Admin

The desired state of the interface.

Oper

The current operational state of the interface.

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

CDP (Enable)

Indicates whether the Cisco Discovery Protocol is currently running on this interface.

Duplex Status

The current mode of operation of the MAC entity. The status 'unknown' indicates that the current duplex mode could not be determined.

Enable Link Trap

Specifies whether Link Up or Link Down traps should be generated for this interface.

Switch

Name of the switch hosting this interface.

Interface

Displays the name of the vFC interface and its association with other interfaces.

Description

Text description of the interface as specified by a network manager.

Status Admin

The desired state of the interface.

Status Oper

The current operational state of the interface.

Speed Oper

Operational speed of the interface

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

Show All Interfaces

Check this checkbox to show all the available interfaces including the interfaces that are not available for binding to a vFC.

Auto Assigin vFC Id

Check this checkbox to select vFC Id automatically. If you do not select this option you must manually enter a valid vFC Id.

Switch Operational Type

Click Ethernet Switch if you are not configuring any Fibre Channel interfaces on the switch. Click FCoE Switch if you are configuring Fibre Channel and FCoE interfaces.

Interface

Name of the physical Ethernet interface. If you hover the cursor over a physical Ethernet interface, any associated virtual interfaces are displayed in the tooltip.

FCoE VLAN(VSAN)

FCoE VLAN (VSAN) mapping to be used by the interface.

Admin Mode

Admin mode of the vFC interface, i.e. F or E

Eth Only

Configures the physical Ethernet without any virtual interfaces. Click the Eth Only button in the column header to set all the interfaces to this value.

vEth Only

Configures the physical Ethernet to have an associated VIG and a virtual Ethernet interface. Click the vEth Only button in the column header to set all the interfaces to this value.

vFC Only

Configures the physical Ethernet to have an associated VIG and a virtual FC interface. Click the vFC Only button in the column header to set all the interfaces to this value.

vFC

Configures the physical Ethernet to have an associated VIG and a virtual FC interface. Click the vFC button in the column header to set all the interfaces to this value.

vEth + vFC

Configures the physical Ethernet to have an associated VIG, a virtual Ethernet interface and a virtual FC interface. Click the vEth + vFC button in the column header to set all the interfaces to this value.

Configure Action Status

Displays the current status of the requested configuration changes.

Description

An `alias' name for the interface as specified by a network manager.

Mtu

The size of the largest frame which can be sent/received on the interface, specified in bytes.

Speed Oper

Operational speed of the interface.

Speed Admin

Failure Cause

Causes of the failures.

PhysAddress

The interface’s MAC address.

Status Admin

The desired state of the interface.

Status Oper

The current operational state of the interface.

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

ConnectorPresent

True if the connector is detected.

CDP (Enable)

An indication of whether the Cisco Discovery Protocol is currently running on this interface.

IscsiAuthMethod

The authentication method.

Promiscuous Mode

Checking or unchecking this option dictates the destination of the packets/frames. If this option is checked, then this interface accepts packets/frames that are addressed to this station. If this option is not selected, then packets accepted by the station are transmitted on the media. Checking or unchecking this option does not affect the reception of broadcast and multicast packets/frames by the interface.

AutoNegotiate

Select this option to enable auto negotiation.

Beacon Mode

In beacon mode, an interface LED is assigned a flashing mode for identification. Select this option to enable beacon mode.

IPAddress/Mask

IP address and subnet mask for the interface.

Description

An `alias' name for the interface as specified by a network manager.

Speed

Operational speed.

PhysAddress

The interface’s WWN.

Admin

The desired state of the interface.

Oper

The current operational state of the interface.

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value contains a N/A value.

PortVSAN

The VSAN that the interface belongs to.

ForwardingMode

Use Store and Forward if the HBA has problems with Passthrough.

Initiator ID Mode

How the initiator is identified on this interface, either by its iSCSI name (name) or by its IP address (ipaddress).

Enable

The intiator proxy mode for this interface. If true, then all the initiators coming on this interface would use the intiator configuration provided by this interface. The initiator configuration include port WWN and node WWN.

Assignment

How the initiator proxy mode FC addresses are assigned. If `auto', then the FC addresses are automatically assigned. If it is `manual', then they have to be manually configured.

Port WWN

The Port FC address used by the intiators on this interface when the intiator proxy mode is on.

Node WWN

The Node FC address used by the initiators on this interface when the initiator proxy mode is on.

Local Port

Local interface TCP port.

SACK

Indicates if the Selective Acknowledgement (SACK) option is enabled or not.

KeepAlive

The TCP keep alive timeout for this iSCSI interface. If the value is 0, the keep-alive timeout feature is disabled.

MinTimeout

The TCP minimum retransmit time.

Max

The TCP maximum retransmissions.

SendBufferSize

The TCP send buffer size.

MinBandwidth

The TCP minimum bandwidth.

MaxBandwidth

The TCP maximum bandwidth.

Estimated Round Trip

The estimated round trip delay of network pipe used for B-D product computation. The switch can use this to derive the TCP window to advertise.

QoS

The TCP QoS code point.

PMTU Enable

Indicates if the Path MTU discovery option is enabled or not.

PMTU Reset Timeout

The PMTU reset timeout.

Connections Normal

The number of normal iSCSI connections.

Connections Discovered

The number of discovery iSCSI connections.

CWM Enable

If true, congestion window monitoring is enabled. If false, it is disabled.

CWM Burst Size

The maximum burst sent after a TCP sender idle period.

Max Jitter

The maximum delay variation (not due to congestion) that can be experienced by TCP connections on this interface.

Port

The local TCP port of this interface.

Switch

Name of the switch.

Interface

Name of the interface.

VLAN mode

The mode in which this VLAN is configured. Static-A port with static VLAN membership directly assigned to a single VLAN. Dynamic-A port with dynamic VLAN membership assigned to a single VLAN based on the content of packets received on the port via VQP queries to VMPS. multiVLAN-A port with multiple VLAN memberships that are directly assigned to one or more VLANs.

VLAN list

The list of VLANs which are allowed on the switch.

Switch

Name of the switch.

ID

Switch ID

Trunk Mode

Specifies whether the mode is access or trunk.

Trunk Status

Ttrunking status of the port.

Native VLAN

Native VLANs

Allowed VLAN List

The list of VLANs which are allowed to be received/transmitted on the port.

Active VLAN List

The list or range of VLANs that are active on the switch.

C3 Rx Bytes

The number of Class 3 bytes, including the frame delimiters, received by this port from its attached Nx_Port.

C3 Rx Frames

The number of Class 3 frames, including the frame delimiters, received by this port from its attached Nx_Port.

C3 Tx Bytes

The number of Class 3 bytes, including the frame delimiters, transmitted by this port to its attached Nx_Port.

C3 Tx Frames

The number of Class 3 frames, including the frame delimiters, transmitted by this port to its attached Nx_Port.

CF Rx Bytes

The number of Class F bytes, including the frame delimiters, received by this port from its attached Nx_Port.

CF Rx Frames

The number of Class F frames, including the frame delimiters, received by this port from its attached Nx_Port.

CF Tx Bytes

The number of Class F bytes, including the frame delimiters, transmitted by this port to its a attached Nx_Port.

CF Tx Frames

The number of Class F frames, including the frame delimiters, transmitted by this port to its attached Nx_Port.

LRRIn

The number of Link reset responses received by the FC-port.

LRROut

The number of Link reset responses transmitted by the FC-port.

OlsIns

The number of Offline Sequence errors received by the FC-Port.

OlsOuts

The number of Offline Sequence errors issued by the FC-Port.

NOSIn

The number of Non-Operational Sequences received by the FC-port.

NOSOut

The number of Non-Operational Sequences transmitted by the FC-port.

LinkResetIns

The number of link reset protocol errors received by the FC-Port from the attached FC-port.

LinkResetOuts

The number of link reset protocol errors issued by the FC-Port to the attached FC-Port.

TxWaitCount

The number of times the FC-port waited due to lack of transmit credits.

RxBBCredit

The maximum number of receive buffers available for holding Class 2, Class 3 received from the logged-in Nx_Port. It is for buffer-to-buffer flow control in the incoming direction from the logged-in Nx_Port to FC-port.

TxBBCredit

The total number of buffers available for holding Class 2, Class 3 frames to be transmitted to the logged-in Nx_Port. It is for buffer-to-buffer flow control in the direction from FC-Port to Nx_Port.

BBCreditTransitionFromZero

The number of transitions of BB credit out of zero state.

Class2

The number of Class 2 frames discarded by this port.

Class3

The number of Class 3 frames discarded by this port.

ClassF

The number of Class F frames discarded by this port.

EISL

The number of Enhanced Inter Switch Link (EISL) frames discarded by the FC-port. EISL frames carry an EISL header containing VSAN among other information.

InDiscards

The total number of inbound frames which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.

OutDiscards

The total number of outbound frames which were chosen to be discarded even though no errors had been detected to prevent their being transmitted.

LinkFailures

The number of link failures detected by the FC-Port.

SigLosses

The number of signal losses detected by the FC-Port.

SyncLosses

The number of loss of synchronization failures detected by the FC-Port.

InvalidTxWords

The number of invalid transmission words detected by the FC-Port.

DelimiterErrors

The number of Delimiter Errors detected by the FC-Port.

AddressIdErrors

The number of address identifier errors detected by the FC-Port.

InvalidCrcs

The number of invalid CRCs detected by the FC-Port. Loop ports should not count CRC errors passing through when monitoring.

ELPFailures

The number of Exchange Link Parameters Switch Fabric Internal Link service request failures detected by the FC-Port. This is applicable to only Interconnect_Port, which are E_Port or B_Port.

Frags

The number of fragmented frames received by the FC-port.

Runts

The number of frames received by the FC-port that are shorter than the minimum allowable frame length regardless if the CRC is good or not.

Jabbers

The number of frames received by the FC-port that are longer than a maximum frame length and also have a CRC error.

TooLongs

The number of frames received by the FC-port where the frame length was greater than what was agreed to in FLOGI/PLOGI. This could be caused by losing the end of frame delimiter.

TooShorts

The number of frames received by the FC-port where the frame length was less than the minimum indicated by the frame header (normally 24 bytes), but it could be more if the DFCTL field indicates an optional header should be present.

Unknowns

The number of unknown class frames received by FC-port.

EOFa

The number of frames received by FC-port with EOF aborts.

Framing

The number of framing errors. This denotes that the FC-port detected an inconsistency of frame structure.

In Octets/In Frames

The number of Class 2 frame bytes and frames, including the frame delimiters, received by this port from its attached Nx_Port.

Out Octets/Out Frames

The number of Class 2 frame bytes and frames, including the frame delimiters, delivered through this port to its attached Nx_Port.

FBSY

The number of busy frame responses.

FRJT

The number of F_RJT frames generated by this port against Class 2 frames.

PBSY

The number of times that port busy was returned to this port as result of a class 2 frame that could not be delivered to the other end of the link. This occurs if the destination Nx_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection).

PRJT

The number of times that port reject was returned to this port as a result of a class 2 frame that was rejected at the destination Nx_Port.

FramePacingTime

Number of 2.5 microsecond units that frame transmission is blocked due to zero credit.

DispErrorsInFrame

Number of frames with disparity errors.

EOFErrs

Number of frames with EOF errors.

DispErrsOutOfFrame

Number of frames with OOF errors.

InvalidOrderSets

Number of invalid or unrecognizable Order Sets outside of frames.

Interval

Elapsed

Time elapsed.

Interface

Name of the interface

InOctectRate

OutOctectRate

RxBytes

The number of bytes, including the frame delimiters, received by this port from its attached N_Port.

RxFrames

The number of frames, including the frame delimiters, received by this port from its attached N_Port.

TxBytes

The number of bytes, including the frame delimiters, transmitted by this port to its attached N_Port.

TxFrames

The number of frames, including the frame delimiters, transmitted by this port to its attached N_Port.

InDiscards

The total number of inbound frames which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.

OutDiscards

The total number of outbound frames which were chosen to be discarded even though no errors had been detected to prevent their being transmitted.

InErrors

The number of incoming errors detected by the virtual FC port.

OutErrors

The number of outgoing errors detected by the virtual FC port.

Interface

Name of the interface.

Alignment Errors

The count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check.

FCS Errors

The count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error.

Single Collision Frames

The count of successfully transmitted frames on a particular interface for which transmission is inhibited by a single collision.

Multiple Collision Frames

The count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collisions.

SQE Test Errors

The number of times the PLS sublayer generated the SQE TEST ERROR message for a particular interface.

Deferred Transmissions

The count of the number of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy.

Late Collisions

The number of times that a collision is detected on a particular interface later than one slot time into the transmission of a packet.

Excessive Collisions

The count of the number of frames for which transmission on a particular interface failes because of excessive collisions. This counter does not increment when the interface is operating in full-duplex mode.

Internal Mac Transmit Errors

The count of the number of frames for which transmission on a particular interface fails because of an internal MAC sublayer transmit error.

Carrier Sense Errors

The number of times that a carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface.

Frame Too Longs

The count of number of frames received on a particular interface that exceed the maximum permitted frame size.

Internal Mac Receive Errors

The count of number of frames for which reception on a particular interface fails because of an internal MAC sublayer receive error.

Symbol Errors

For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present

Rx Bytes

The total number of bytes received on the interface, including framing characters.

RxFrames

The number of frames received on the interface.

Rx Multicast Frames

(Nexus 5000 Series only) The number of multicast frames received on the interface.

Rx Broadcast Frames

(Nexus 5000 Series only) The number of broadcast frames received on the interface.

TxBytes

The total number of bytes transmitted out of the interface, including framing characters.

TxFrames

The total number of frames transmitted out of this interface.

Tx Multicast Frames

(Nexus 5000 Series only) The number of multicast frames transmitted out of this interface.

Tx Broadcast Frames

(Nexus 5000 Series only) The number of multicast frames transmitted out of this interface.

RxErrors

The number of inbound frames that contained errors preventing them from being deliverable to a higher-layer protocol.

TxErrors

The number of outbound frames that could not be transmitted because of errors.

RxDiscards

The number of inbound frames which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.

TxDiscards

The number of outbound frames which were chosen to be discarded even though no errors had been detected to prevent their being transmitted.

Description

Alias name for the interface as specified by a network manager.

Members

Members of this Ethernet port channel.

Oper Speed

Operational speed of the interface.

Mtu

The size of the largest frame which can be sent/received on the interface, specified in bytes.

PhysAddress

The interface’s MAC address.

Status Admin

The desired state of the interface.

Status Oper

The current operational state of the interface.

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

RxBytes

Total number of bytes received on an iSCSI session.

TxBytes

Total number of bytes transmitted on an iSCSI session.

IPSEC

A collection of objects for iSCSI connection statistics.

Opens

The number of times connections have been opened.

Accepts

The number of times connections have been accepted.

Failed

The number of times connections have failed.

RxResets

The number of times connections have been reset.

Est

The number of connections that have been established.

RxSegs

The total number of segments received on established connections, including those received in error.

TxSegs

The total number of segments sent, except for those containing retransmitted bytes.

ReTxSegs

The total number of segments retransmitted.

BadSegs

The total number of segments received in error (e.g., bad checksums).

TxSegResets

The number of segments sent containing the "reset" flag.

SplitSeg

The number of segments sent which were less than the minimum.

DupACKs

The number of duplicate ACKs received.

RxBytes

The number of header and data bytes received.

TxBytes

The number of header and data bytes sent.

C3 Rx Bytes

The number of incoming bytes of data traffic.

C3 Tx Bytes

The number of outgoing bytes of data traffic.

CF Rx Bytes

The number of incoming bytes of control traffic.

CF Tx Bytes

The number of outgoing bytes of control traffic.

Rx Error

The number of inbound frames that contained errors preventing them from being deliverable to a higher-layer protocol.

Tx Error

The number of outbound frames that could not be transmitted because of errors.

RxDiscard

The number of inbound frames which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.

TxDiscard

The number of outbound frames which were chosen to be discarded even though no errors had been detected to prevent their being transmitted.

Rx Bytes

Number of incoming bytes.

Rx Frames

Number of incoming frames.

Tx Bytes

Number of outgoing bytes.

Tx Frames

Number of outgoing frames.

Rx Errors

Number of incoming errors.

Tx Errors

Number of outgoing errors.

Rx Discards

Number of incoming discards.

Tx Discards

Number of outgoing discards.

Rx Bytes

Number of incoming bytes on this virtual N-port.

Rx Frames

Number of incoming frames on this virtual N-port.

Tx Bytes

Number of outgoing bytes on this virtual N-port.

Tx Frames

Number of outgoing frames on this virtual N-port.

Rx Bytes

Number of incoming bytes on this virtual N-port.

Rx Frames

Number of incoming frames on this virtual N-port.

Tx Bytes

Number of outgoing bytes on this virtual N-port.

Tx Frames

Number of outgoing frames on this virtual N-port.

Cmds

Number of incoming FCP Command frames in this session.

XferRdys

Number of incoming FCP Transfer Ready frames in this session.

DataFrames

Number of incoming FCP Data frames.

Status

Number of incoming FCP status frames.

DataBytes

Number of incoming FCP Data bytes.

OverRuns

Number of incoming FCP Overrun frames in this session.

UnderRuns

Number of incoming FCP Underrun frames in this session.

Cmds

Number of outgoing FCP Command frames in this session.

XferRdys

Number of outgoing FCP Transfer Ready frames in this session.

DataFrames

Number of outgoing FCP Data frames.

Status

Number of outgoing FCP status frames.

DataBytes

Number of outgoing FCP Data bytes.

OverRuns

Number of outgoing FCP OverRun frames in this session.

UnderRuns

Number of outgoing FCP UnderRun frames in this session.

InELSFrames

Number of incoming Extended Link Service frames in this session.

InBLSFrames

Number of incoming Basic Link Service frames in this session.

OutELSFrames

Number of outgoing Extended Link Service frames in this session.

OutBLSFrames

Number of outgoing Basic Link Service frames in this session.

InAborts

Number of incoming aborted frames in this session.

OutAborts

Number of outgoing aborted frames in this session.

OpenXchanges

Number of Open Exchanges in this session.

InBadFc2Drops

Number of FC2 dropped frames in this session.

InBadFcPDrops

Number of FCP dropped frames.

InFCPDataExcess

Number of FCP Data Excess frames in this session.

Description

Alias name for the interface as specified by a network manager.

PortVsan

The VSAN ID to which this interface is statically assigned.

Oper Mode

The current operating mode of the port.

AutoChannelCreate

If checked, automatically create the PortChannel.

Admin

The desired state of the interface.

Oper Status

The current operational state of the interface.

FailureCause

The cause of current operational state of the port.

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

FICON Address

The FICON port address of this port.

E port Congestion Drop

Specify the time for E port congestion drop. Or click on default to input a default value. The unit is ms.

F port Congestion Drop

Specify the time for F port congestion drop. Or click on default to input a default value. The unit is ms.

F port NoCredit Drop

Specify the time for no credit drop. Click on disable if you do not want to drop the frames without tx/rx credits or click on default to input a default value. The unit is ms.

E Port slowport-monitor

Specify the slowport-monitor timeout value for E port. Click on disable to disable slowport monitoring. Or click on default to input a default value. The unit is ms.

F Port slowport-monitor

Specify the slowport-monitor timeout value for F port. Click on disable to disable slowport monitoring. Or click on default to input a default value. The unit is ms.

Type

Specifies the license that can be acquired for a given interface. Currently, the Port Activation license can be defined.

Config

Displays the license for which an interface is eligible. An interface which is not eligible for any type of license will not be displayed.

Oper

The current state of port license on the interface is displayed.

Description

An `alias' name for the interface as specified by a network manager.

Mtu

The size of the largest frame which can be sent/received on the interface, specified in bytes.

Oper

Operational speed

PhysAddress

The interface’s MAC address.

Admin

State of the admin.

Oper

The current operational state of the interface.

LastChange

When the interface entered its current operational state.

CDP

Enable or disable CDP.

Default Gateway

The IP address of the default gateway.

Description

Alias name for the interface as specified by a network manager.

VSAN Id Port

VSAN ID to which this interface is statically assigned.

VSAN Id Dynamic

The VSAN ID that this interface has been dynamically assigned (see DPVM).

CDP (Enable)

An indication of whether the Cisco Discovery Protocol is currently running on this interface.

Promiscuous Mode

Checking or unchecking this option dictates the destination of the packets/frames. If this option is checked, then this interface accepts packets/frames that are addressed to this station. If this option is not selected, then packets accepted by the station are transmitted on the media. Checking or unchecking this option does not affect the reception of broadcast and multicast packets/frames by the interface9.

Auto Negotiate

An indication of whether auto-negotiation of speed and duplex mode should be used on this interface.

Beacon Mode

In beacon mode, an interface LED is assigned a flashing mode for identification. Select this option to enable beacon mode.

Mode Admin

The port mode configured by the user. Modes are:

Mode Oper

The current operating mode of the port.

SpeedGroup

Specifies the current speed group configuration on the given interface.

Speed Admin

The port speed configured by the user. The port speed values are auto, 1Gb, 2Gb, 4Gb, 8Gb, 10Gb, autoMax2G, and autoMax4G. Note On a Cisco Nexus 5000 Series switch that runs Cisco NX-OS Release 4.2(2), you can configure the 8-Gbps administrative speed only on an M1060 switch module. You can configure the speed to 1 Gbps, 2 Gbps, or 4 Gbps on all switch modules on a Cisco Nexus 5000 Series switch that runs Cisco NX-OS Release 4.2(2) or earlier releases.

Speed Oper

Operational speed.

RateMode

Specifies the interface as dedicated mode or shared mode.

Status Service

Specifies whether the interface is in service or out of service.

Status Admin

The desired state of the interface.

Status Oper

The current operational state of the interface.

Status FailureCause

The cause of current operational state of the port.

StatusWasEnabled

If true, this port successfully completed a link initialization.

Status LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

Port Owner

Administratively assigned name of the current owner of the interface resource.

Oper

The receive buffer-to-buffer credits configured for the operational port mode.

Model

The BB_Credit model used by the FC-port. The alternate BB_Credit management model can be used in the arbitrated loop topology to manage the flow of frames between the two ports participating in the current loop circuit. Since this is a characteristic of a physical port, this is not applicable for Port Channel ports.

Admin

The receive buffer-to-buffer credits configured for this port.

Extended

The extended BB credits that can be configured on an FC port (in the range 256 through 4095). The acceptable value depends on the BB credit configuration of other ports on the module. This value can only be modified on modules that support the extended BB credit feature.

AdminISL

The receive buffer-to-buffer credits configured for this port to be used if it is operating in xE_port mode.

AdminFx

The receive buffer-to-buffer credits configured for this port to be used if it is operating in Fx mode.

PerfBuffer Admin

The performance buffers configured for this port. These buffers in addition to the buffer-to-buffer credits are used to improve the performance of a port. If a value of 0 is set, then the module uses the built-in algorithm to calculate the number of performance buffers to be used.

PerfBuffer Oper

The performance buffers presently operational on this port.

Oper Rx

The maximum number of receive buffers available for holding Class 2, Class 3, Class F frames received from the peer Interconnect_Port.

Oper Tx

The total number of buffers available for holding Class 2, Class 3, Class F frames to be transmitted to the peer Interconnect_Port.

Current Rx

The current value of receive buffer-to-buffer credits for this port.

Current Tx

The current value of transmit buffer-to-buffer credits for this port.

BbScn Notify

Indicates whether the Buffer-to-buffer State Change Number (BB_SC_N) mode is enabled. If checked, BB_SC_N mode is enabled. If unchecked, BB_SC_N mode is disabled.

PortChannel Id

The port channel that this interface belongs to.

Fabric WWN

The world wide name given to this interface.

Mtu bytes

The size of the largest frame which can be sent/received on the interface, specified in bytes.

RxDataFieldSize bytes

The largest Data_Field size for an FT_1 frame that can be received by this port.

HoldTime us

The maximum time that the FC-Port shall hold a frame in the transmitter buffer before discarding it, if it is unable to deliver the frame.

Auto Port Channel

Check if you want the PortChannel to be created automatically.

FEC Admin

Specifies the port FEC state configured.

FEC Oper

Specifies the current operating FEC state of the port.

FcId

The address identifier that has been assigned to the logged-in Nx_Port.

PortName

The world wide name of the logged-in Nx_Port.

NodeName

The world wide name of the Remote Node the logged-in Nx_Port belongs to.

Original PWWN

The original port WWN for this interface

Version

The version of FC-PH that the Fx_Port has agreed to support from the Fabric Login.

BBCredit Rx

The maximum number of receive buffers available for holding Class 2, Class 3 received from the logged-in Nx_Port. It is for buffer-to-buffer flow control in the incoming direction from the logged-in Nx_Port to FC-port.

BBCredit Tx

The total number of buffers available for holding Class 2, Class 3 frames to be transmitted to the logged-in Nx_Port. It is for buffer-to-buffer flow control in the direction from FC-Port to Nx_Port. The buffer-to-buffer flow control mechanism is indicated in the respective BbCreditModel.

CoS

The classes of services that the logged-in Nx_Port has requested the FC-Port to support and the FC-Port has granted the request.

Class2 RxDataSize

The Class 2 Receive Data Field Size of the logged-in Nx_Port. Specifies the largest Data Field Size for an FT_1 frame that can be received by the Nx_Port.

Class2 SeqDeliv

Whether the FC-Port has agreed to support Class 2 sequential delivery during the Fabric Login. This is meaningful only if Class 2 service has been agreed. This is applicable only to Fx_Ports.

Class3 RxDataSize

The Class3 Receive Data Field Size of the logged-in Nx_Port. Specifies the largest Data Field Size for an FT_1 frame that can be received by the Nx_Port.

Class3 SeqDeliv

Whether the FxPort has agreed to support Class 3 sequential delivery during the Fabric Login. This is meaningful only if Class 3 service has been agreed. This is applicable only to Fx_Ports.

Neighbor Port

The port world wide name of the peer Interconnect_Port.

Neighbor Switch

The node world wide name of the peer Node.

BBCredit Rx

The maximum number of receive buffers available for holding Class 2, Class 3, Class F frames received from the peer Interconnect_Port. It is for buffer-to-buffer flow control in the incoming direction from the peer Interconnect_Port to local Interconnect_Port. The buffer-to-buffer flow control mechanism is indicated in the respective BbCreditModel.

BBCredit Tx

The total number of buffers available for holding Class 2, Class 3, Class F frames to be transmitted to the peer Interconnect_Port. It is for buffer-to-buffer flow control in the direction from the local Interconnect_Port to peer Interconnect_Port. The buffer-to-buffer flow control mechanism is indicated in the corresponding BbCreditModel.

CoS

The classes of services that the peer Interconnect_Port has requested the local Interconnect_Port to support and the local Interconnect_Port has granted the request.

Class2 SeqDeliv

Whether the local Interconnect_Port has agreed to support Class 2 sequential delivery during the Exchange Link Parameters Switch Fabric Internal Link Service request. This is meaningful only if Class 2 service has been agreed.

Class2 RxDataSize

The Class 2 Receive Data Field Size of the peer Interconnect_Port. Specifies the largest Data Field Size for an FT_1 frame that can be received by the Interconnect_Port. This is meaningful only if Class 2 service has been agreed.

Class3 SeqDeliv

Whether the local Interconnect_Port has agreed to support Class 3 sequential delivery during the Exchange Link Parameters Switch Fabric Internal Link Service request. This is meaningful only if Class 3 service has been agreed.

Class3 RxDataSize

The Class 3 Receive Data Field Size of the peer Interconnect_Port. Specifies the largest Data Field Size for an FT_1 frame that can be received by the Interconnect_Port. This is meaningful only if Class 3 service has been agreed.

ClassF X_ID

When true indicates that the peer Interconnect_Port supplying this parameter requires that an interlock be used during X_ID assignment in Class F. This is meaningful only if Class F service has been agreed.

ClassF RxDataSize

The Class F Receive Data Field Size of the peer Interconnect_Port. Class F service is always agreed between two Interconnect_Ports. Specifies the largest Data Field Size for an FT_1 frame that can be received by the Interconnect_Port.

ClassF ConSeq

The number of sequence status blocks provided by the Interconnect_Port supplying the parameters for tracking the progress of a sequence as a sequence recipient. The maximum number of concurrent sequences that can be specified is 255. A value of N/A in this field is reserved.

ClassF EECredit

The maximum number of Class F data frames which can be transmitted by an Interconnect_Port without receipt of accompanying ACK or Link_Response frames. The minimum value of end-to-end credit is one. The end-to-end credit field specified is associated with the number of buffers available for holding the Data_Field of a Class F frame and processing the contents of that Data_Field by the Interconnect_Port supplying the parameters.

ClassF OpenSeq

The open sequences per exchange shall specify the maximum number of sequences that can be open at one time at the recipient between a pair of Interconnect_Ports for one exchange. This value is used for exchange and sequence tracking.

Admin

The trunking mode configured by the user.

Oper

The current trunking mode of the port.

Allowed VSANs

The list of VSANs which are allowed to be received/transmitted on the port when the port is operating in trunking mode. Only ports operating in trunk mode can belong to multiple VSANs.

Up VSANs

The list of VSANs whose operational state is up, that this port is associated with. Only ports operating in trunk mode can be associated to multiple VSANs. This is applicable to only ports operating in trunk mode.

FailureCause

An entry is shown in this table if there is an error in the trunk status for the given VSAN.

Switch

The name of the switch.

Ethernet Interface

A unique value that identifies the ethernet interface.

Ethernet Status

The current operational state of the ethernet interface.

Ethernet IP Address

The Internet address for this entity.

Peer IP Address

The Internet address for this entity

Port

The Port ID string as reported in the most recent CDP message.

Peer Interface

A unique value that identifies the peer interface on this device to which this link pertains.

Peer Device Id

The Peer Device ID string as reported in the most recent CDP message.

IP Security Enabled

Specifies whether the IP Security is turned on or not.

BeaconMode

If enabled, an interface LED is put into flashing mode for easy identification of a particular interface.

ConnectorPresent

If true, there is a physical connector.

ConnectorType

The module type of the port connector.

TransmitterType

The technology of the port transceiver.

Vendor

The connector unit vendor.

PartNumber

The connector unit part number.

Revision

The port revision of the connector unit.

SerialNo

The serial number of the connector unit.

FC-PH Vers Low

The lowest version of FC-PH that the FC-Port is capable of supporting.

FC-PH Vers High

The highest version of FC-PH that the FC-Port is capable of supporting.

RxDataSize Min

The minimum size in bytes of the Data Field in a frame that the FC-Port is capable of receiving from its attached FC-port.

RxDataSize Max

The maximum size in bytes of the Data Field in a frame that the FC-Port is capable of receiving from its attached FC-port.

HoldTime Min

The minimum holding time (in microseconds) that the FC-Port is capable of supporting.

HoldTime Max

The maximum holding time (in microseconds) that the FC-Port is capable of supporting.

CoS

The Bit mask indicating the set of Classes of Service that the FC-Port is capable of supporting.

ServiceStateCapable

Indicates whether this interface is capable of handling service state change.

PortRateMode Capable

Indicates whether this interface is capable of being configured as dedicated or shared port rate modes.

AdminRxBbCreditExtendedCapable

If true, it is capable of changing the extended buffer-to-buffer credits on the interface. The user can configure the object fcIfAdminRxBbCreditExtended on this interface

Class2Seq Deliv

The flag indicating whether or not the FC-Port is capable of supporting Class 2 Sequential Delivery.

Class3Seq Deliv

The flag indicating whether or not the FC-Port is capable of supporting Class 3 Sequential Delivery.

TypeNumber

The type number of the peer node. For example, the type number could be 002105.

SerialNumber

The sequence number assigned to the peer node during manufacturing. For example, the serial number could be 000000023053.

Tag

The identifier of the port in the peer node connected to this port.

FcId

Address Identifier assigned to NX-Port

Status

Specifies the status of the row, is valid, invalid or old.

Name

Name of this port.

Manufacturer

The name of the company that manufactured the peer node. For example, the manufacturer info could be HTC.

ModelNumber

The model number of the peer node. For example, the model number could be F20.

PlantOfMfg

The plant code that identifies the plant of manufacture of the peer node. For example, the plant code of manufacture could be 00.

UnitType

The type of the peer node that this port is communicating.

Alert

The type of link incident that occurred on this interface.

Pwwn

The WWN (Worldwide Name) of the virtual N-port.

FcId

Fibre Channel Identifier of the virtual N-port.

State

The operational state of the virtual N-port.

DownReason

If the state of the N-port is 'down' as depicted by the instance of State, this value denotes the reason why this N-port is 'down'.

NportPwwn

The WWN of the N-port that belongs to this session.

PeerPwwn

The WWN of the remote N-port for this session.

PeerNwwn

The WWN of the remote N-port for this session.

PeerFcId

Fibre Channel Identifier of the remote port for this session.

Field

Description

AttemptFails

The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.

InErrs

The total number of segments received in error (e.g., bad TCP checksums).

ActiveOpens

The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.

PassiveOpens

The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.

EstabResets

The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.

InSegs

The total number of segments received, including those received in error. This count includes segments received on currently established connections.

OutSegs

The total number of segments sent, including those on current connections but excluding those containing only retransmitted bytes.

RetransSegs

The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted bytes.

OutRsts

The number of TCP segments sent containing the RST flag.

Description

Alias name for the interface as specified by a network manager.

Mtu

The size of the largest frame which can be sent/received on the interface, specified in bytes.

PhysAddress

The interface’s address at its protocol.

Admin

The desired state of the interface.

Oper

The current operational state of the interface.

LastChange

When the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this value is N/A.

IPAddress/Mask

The IP address and mask of the interface.

iSCSI AuthMethod

The authentication method for this interface.

iSNS ProfileName

The iSNS server profile name for this interface.

PortVsan

VSAN to which this interface is statically assigned.

Description

Alias name for the interface as specified by a network manager.

Admin Mode

The port mode configured by the user. If the user configured the port as auto(1), then the port initialization scheme determines the mode of the port. In this case the user can look at OperMode to determine the current operating mode of port. Only auto(1) or ePort(4) is allowed.

Oper Mode

The current operating mode of the port.

Admin Speed

The port speed configured by the user.

Oper Speed

The interface’s current bandwidth per second.

Admin Status

The desired state of the interface.

Oper Status

The current operational state of the interface.

FailureCause

The cause of current operational state of the port.

LastChange

The time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the switch, then this is a zero or N/A value.

Admin Mode

The channel mode desired by the network manager.

Oper Mode

The current operating channel mode of the port.

Force

The method to add port(s) to a Port Channel port.

MemberList By Interface

The list of the E_ports that are members of this Port Channel port.

MemberList By FICON

The list of the E_ports that are members of this Port Channel port.

MemberList LoadBalanced

Those ports which are actively participating in the PortChannel.

LastAction Status

The status of the last operation (add or remove a member) done to change the member list of a Port Channel Port. When no ports are added or the last operation is successful then this value is successful. If this value is failed then the user can look at LastAddStatusCause to find the reason of failure.

LastAction FailureCause

The cause of failure to last operation (add or remove a member) done to change the member list of a Port Channel port.

LastAction Time

The timestamp indicating the time of last action performed on this entry.

CreationTime

The timestamp of this entry’s creation time.

FICON Address

The FICON port address. If empty, then this channel is not used by FICON. (This column is displayed if FICON is enabled. This column is grayed out if the Port Channel is auto-created.)

VirtualPwwnauto

Enables automatic generation of Virtual WWNs on all the F_port interfaces. If the value of VirtualPWWNauto is set to 'true', the value of VirtualWWN Auto of all the entries in the VirtualWWN table is implicitely set to true.

Field

Description

virtual pWWN

This is the virtual port WWN for this interface. If the value of VirtualWwnAuto is 'true', then value of this virtual pWWWN is automatically generated by the device.If value of this pWWWN is set explicitely, then value of VirtualWwnAuto is implicitely set to 'false'. If length of pWWWN is zero, then automatic virtual WWN generation is disabled. This pWWWN can not be set to length zero

Auto

Enable automatic generation of Virtual WWNs on this interface.If the value of VirtualWwnPwwn is set explicitely, then the value of Auto will be implicitely set to false. Also, if this Auto is set to 'true', then value of VirtualWwnPwwn is overwritten with auto generated virtual port WWN.

LastChange

The value of sysUpTime at the time of the last change to this Virtual WWN Entry.

virtual pWWN

This is the virtual port WWN for this device port WWN. In order to minimize WWN collision, no two instances of this Virtual pWWN can have same value. Note :The Virtual pWWN cannot be changed when corresponding device is logged in.

LastChange

The value of sysUpTime at the time of the last change to this Virtual WWN Entry.

ModeActivation

To enable/disable FIPS mode on the device. FIPS 140-2 is a set of security requirements for cryptographic modules and it details the U.S. Government requirements for cryptographic modules. A module will comprise both hardware and software, eg a datacenter switching or routing module. The module is said to be in FIPS enabled mode when a request is recieved to enable the FIPS mode and a set of self-tests are successfully run in response to the request. If the self-tests fail, then an appropriate error is returned

Interface

This is a unique value that identifies the interface on this FCIP device to which this link pertains.

VSAN List Admin

This is the list of VSANs (in the range 1 through 2047) for which Ficon Tape Acceleration is configured. Only VSANs with a cficonVsanEntry of CISCO-FICON-MIB present can be configured for Ficon Tape Acceleration.

VSAN List Oper

This is the list of VSANs (in the range 1 through 2047) for which Ficon Tape Acceleration is operationally "ON".

Channel

The channel group mode of this PortChannel.

Persistent

True if the PortChannel is persistent.

Dest Interface

The Span Destination port interface.

Filter VSAN List

The VSANs that are assigned to this session.

Status Admin

Suspend an active session or activate an inactive session.

Status Oper

The current state of the session.

Description

The description of the session status.

VSAN List

The VSANs that are assigned to this session.

Or Interface (Direction)

The destination port ID to be configured for the session.

Inactive Reason

Description of the reason why this session is not active.

MaxQueuedSpanPackets

This field specifies the drop threshold packets for all span sessions.The MaxQueuedSpanPackets field is only available when no session is active.

Interface, Direction

The destination port ID configured for the session, and the direction of traffic.

Linked, Destination Interfaces

The interfaces that are doing the tracking.

VSAN Type

Whether a single VSAN or all VSANs are being tracked.

VSAN ID

If a single VSAN is being tracked, the ID of that VSAN.

Interface

The interface of the port to be configured for the forced-shut mode.

Force Shut

If true, the port is brought down administratively, and you must bring the port up manually. If false, the port is brought down operationally only, and is brought up again as soon as any one of the tracked ports comes up.

Interface

Name of the interface

Enable

Specifies whether an interface can be stopped from changing between up and down states or allowed to change states continuously.

Duration (sec)

Specifies the time duration in which a port is allowed to change states.

Number of Flaps

Specifies the number of times the port can flap in the time specified in the Duration.

Oper

Operational state of the interface.

Dedicated 4 Gbps on the first port of each group and the remaining ports 8 Gbps shared

Allocates a rate mode and admin speed of 4 Gbps on the first port of each group and the remaining ports share 8 Gbps depending on the operational speed of the ports

Dedicated 8 Gbps on the first port of each group and the remaining ports 8 Gbps shared

Allocates a rate mode and admin speed of 8 Gbps on the first port of each group and the remaining ports share 8 Gbps depending on the operational speed of the ports

Shared 8 Gbps on all ports (initial & default settings)

Allocates a rate mode and admin speed of 8 Gbps on all the available ports. This is the default setting.

Dedicated 2 Gbps on the first port of each group and the remaining ports 4 Gbps shared

Allocates a rate mode and admin speed of 2Gbps on the first port of each group and the remaining ports share 4 Gbps depending on the operational speed of the ports

Dedicated 8 Gbps on the first port of each group and the remaining ports 4 Gbps shared

Allocates a rate mode and admin speed of 8 Gbps on the first port of each group and the remaining ports share 4 Gbps depending on the operational speed of the ports

Shared Auto with Maximum of 4 Gbps on all ports (initial & default settings)

Allocates a maximum rate mode and admin speed of 4Gbps on all the available ports. This is the default setting.

Dedicated 8 Gbps on the first port of each group and the remaining ports 8G shared

Allocates a rate mode and admin speed of 8Gbps on the first port of each group and the remaining ports share 8 Gbps depending on the operational speed of the ports

Shared Auto on all ports (initial & default settings)

Allocates a rate mode and admin speed of 8 Gbps on all the available ports. This is the default setting.

Dedicated 8 Gbps on the first 4 ports in each 6-port port group and the remaining ports 8G shared

Allocates a rate mode and admin speed of 8Gbps on the first 4 ports in each 6-port port group and the remaining ports share 8 Gbps depending on the operational speed of the ports.

Dedicated 8 Gbps on the first port of each group and the remaining ports 8G shared

Allocates a rate mode and admin speed of 8 Gbps on the first port of each group and the remaining ports share 8 Gbps depending on the operational speed of the ports.

Shared 8G 0n all ports

Allocates a rate mode and admin speed of 8 Gbps on all the available ports. This is the default setting.

Dedicated 4G 0n all ports

Allocates a rate mode and admin speed of 4Gbps on all the available ports.

Dedicated 10G on following ports:

Allocates a rate mode and admin speed of 10Gbps on the following ports.

Dedicated 8 Gbps on on all ports

Allocates a rate mode and admin speed of 8 Gbps on all the available ports.

Shared 8 Gbps on on all ports - initial and default settings.

Allocates a rate mode and admin speed of shared 8 Gbps on all the available ports.

Dedicated 10G on following ports:

Allocates a rate mode and admin speed of 10Gbps on the specified ports.

Dedicated 10G on the following ports:

Allocates dedicated rate mode and admin speed of 10 Gbps on the specified ports.

Unconfigure 10G on the following ports:

Reverts to default rate mode and admin speed on the specified ports. Transceiver frequencey is set to FC. This operation is disruptive.

Name

The name of the VSAN. Note that default value will be the string VSANxxxx where xxxx is value of vsanIndex expressed as 4 digits. For example, if vsanIndex is 23, the default value is VSAN0023.

Mtu

The MTU of the VSAN. Normally, this is 2112.

LoadBalancing

The type of load balancing used on this VSAN.

InterOp

The interoperability mode of the local switch on this VSAN.

AdminState

The state of this VSAN.

OperState

The operational state of the VSAN.

InOrderDelivery

The InorderDelivery guarantee flag of device. If true, then the inorder delivery is guaranteed. If false, it is not guaranteed.

DomainId

Specifies an insistent domain ID.

FICON

True if the VSAN is FICON-enabled.

Network Latency

Network latency of this switch on this VSAN. This is the time interval after which the frames are dropped if they are not delivered in the order they were transmitted.

Switch

Name of the switch

Ports

FC Ports in VSAN

Channels

PortChannels in VSAN

FCIP

FCIP Interfaces in VSAN

iSCSI

iSCSI Interfaces in VSAN

FICON

Interfaces in VSAN by FICON

FC Virtual Interface

Virtual FC interfaces in VSAN

VSAN ID

The ID of the VSAN containing the McData switch.

WWN

The WWN of the McData switch.

VSAN Id

The ID of the VSAN.

R_A_TOV

The Resource_Allocation_Timeout Value used for FxPorts as the timeout value for determining when to reuse an NxPort resource such as a Recovery_Qualifier. It represents E_D_TOV plus twice the maximum time that a frame may be delayed within the Fabric and still be delivered. Note that all switches in a fabric should be configured with the same value of this timeout.

D_S_TOV

The Distributed_Services_Timeout Value which indicates that how long a distributed services requestor will wait for a response.

E_D_TOV

The Error_Detect_Timeout Value used for FxPorts as the timeout value for detecting an error condition. Note that all switches in a fabric should be configured with the same value of this timeout. Note that value must be less than value of D_S_TOV.

NetworkDropLatency

Network latency of this switch on this VSAN.

Zone Behavior

Represents the initial value for default zone behavior on a VSAN when it is created. If a VSAN were to be deleted and re-created again, the default zone behavior will be set to the value specified for this object.

Propagation Mode

Represents the initial value for zone set propagation mode on a VSAN when it is created. If a VSAN were to be deleted and re-created again, the zone set propagation mode will be set to the value specified for this object.

VSAN List

The list of configured VSANs that are part of IVR topology on this device.

VSAN List

The list of configured VSANs that are part of IVR topology on this device.

Fabric Id

The configured Default Autonomous Fabric ID of this switch.

Activate Local Topology

Setting this object to activate is a request for the configured IVR topology to be activated on this device. i.e., for the current configuration of IVR topology to be cloned, with the clone becoming the active IVR topology.

IsActive

This object indicates of IVR topology is active or not. If true, the IVR topology is active. If false, the IVR topology is not active.

Activation Time

When the IVR topology was most recently activated. If the IVR topology has not been activated prior to the last re-initialization of the local network management system, then this value will be N/A.

Enable IVR NAT

Enable FCID and VSAN identifier translation across VSAN boundaries. If true, the VSAN identifier as well as the entire FCID of the end devices would be modified as frames cross VSAN boundaries.

Auto Discover Topology

Enable automatic VSAN topology discovery. If true, automatic VSAN topology discovery is turned on. IVR processes would communicate with each other to provide a global view of the physical topology to all the IVR enabled switches. If false, automatic VSAN topology discovery is turned off.

Add Virtual Domain to FC Domain List

This object lists VSANs in which the virtual domains in a VSAN are added to the domain list in that VSAN.

VSAN List

The list of VSANs that are part of IVR topology on this device.

Field

Description

Status

Status of the active IV Zoneset on this VSAN.

Discrepancy

The checksum of the enforced (active) IV zoneset.

RegionID

Identifies the CFS configuration supported region.

Domain Id

The FC domain ID that will be used to represent the VSAN.

FCID

The FCID to be used by IVR to represent the device.

VSAN Id

IVR VSAN ID.

Zone

Active IVR zone name.

Fabric Id

Autonomous fabric ID.

Switch Interface

Switch interface to which the zone member is connected to.

Name

Zone member name.

WWN

Zone member WWN.

FcId

Zone member FC ID.

LUNs

Zone member LUN.

Status

Zone

Active IVR zone name.

QoS

True if QoS enabled, otherwise false.

QoS Priority

QoS priority value (Low, Medium, or High).

Broadcast

Specifies if broadcast zoning is enabled on this default zone on this VSAN. If true, then it is enabled. If false, then it is disabled.

VSAN Id

IVR VSAN ID.

Zone

Active IVR zone name.

Fabric Id

Autonomous fabric ID.