Reset Code # |
Reset Code |
Radio Reset Reason |
1 |
RADIO_FC_FLASH |
The radio has failed to respond to the "dot11 flash" command. Not applicable for 802.11n radios. |
2 |
RADIO_FC_RESET |
The radio has failed to respond to a request to reset the interface. |
3 |
RADIO_FC_START |
The radio failed to start. |
4 |
RADIO_FC_CLIENT_FREE |
The radio or radio driver was unable to completely remove a client that is no longer serviced by the radio. |
5 |
RADIO_FC_TX_STATE |
A completed packet transmission resulted in an unexpected status code from the hardware. This failure automatically results in a radio coredump written to the flash filesystem. |
6 |
RADIO_FC_TX_STOPPED |
One or more packets have been submitted to the radio to be transmitted, but have not been reported as completed for 60 seconds. |
7 |
RADIO_FC_TX_STUCK |
--not used-- |
8 |
RADIO_FC_TX_RING_ADDR |
A packet that has completed transmission is reported with an invalid internal memory address. Not applicable to 802.11n radios. |
9 |
RADIO_FC_TX_ACTIVE_Q |
A transmit packet is attempted to be removed from an empty queue. |
10 |
RADIO_FC_TX_INPROG |
The driver attempts to free a packet that the radio still has in progress. |
11 |
RADIO_FC_TX_REF_CNT |
Memory for a completed transmission is attempted to be released twice. |
12 |
RADIO_FC_TX_AMSDU_STATE |
The status of a transmitted Aggregation MAC Service Data Unit (AMSDU) packet is indeterminate. |
13 |
RADIO_FC_BA_LOST |
An 802.11n Block Ack packet is assembled for a client that does not exist. |
14 |
RADIO_FC_CMD_TIMEOUT |
A command from the AP to the radio has taken 12 seconds without a response. |
15 |
RADIO_FC_CMD_FAILED |
The radio reported that a command from the AP has failed to execute. |
16 |
RADIO_FC_CMD_BUSY |
A command from the AP to the radio does not appear to complete. Not applicable to 802.11n radios. |
17 |
RADIO_FC_BAP_ERR |
A PCMCIA timeout occured when a radio register is accessed. Does not apply to 802.11n radios.apply to 802.11n radios.A PCMCIA timeout occured when a radio register is accessed. Does not apply to 802.11n radios.A PCMCIA timeout occured when a radio register is accessed. Does not apply to 802.11n radios.A PCMCIA timeout occured when a radio register is accessed. Does not apply to 802.11n radios. |
18 |
RADIO_FC_LOAD_TIMEOUT |
The AP timed out when it attempted to load the radio firmware. |
19 |
RADIO_FC_LOAD_FAIL |
The copy of radio firmware from the AP to the radio completed, but was not accepted by the radio. |
20 |
RADIO_FC_RX_PTR |
A received packet points to an invalid area of memory. |
21 |
RADIO_FC_BUS_RESET |
An unexpected radio reset occurred in a four-radio system. |
22 |
RADIO_FC_GET_CODE |
The AP was unable to find or load an appropriate radio firmware file to load into the radio. This could occur if the firmware image is corrupted or not present. |
23 |
RADIO_FC_TX_JAMMED |
The radio hardware transmitter-watchdog detected a stuck packet and a reset of only the hardware transmitter was unsuccessful . |
24 |
RADIO_FC_CLIENT_STUCK |
Client packets cannot be transmitted. Client packet stuck in radio for more than 60 seconds. |
25 |
RADIO_FC_SPECTRUM |
Spectrum Firmware, from Clean Air module, requires a radio reset. |
26 |
RADIO_FC_RX_RING_ADDR |
There is a problem in the Radio packet receive buffer. Bad RX Ring Address. |
27 |
RADIO_FC_NDP_STUCK |
--not used-- |
28 |
RADIO_RC_RF_MON |
The radio goes into or out of monitor mode, due to the CLI enabled the Radio Frequency (RF) monitor/store mode. |
29 |
RADIO_RC_RF_MON_PROM |
The radio goes into or out of promiscuous monitor mode, due to turn on/off RF monitor promiscous mode. |
30 |
RADIO_RC_TRACE |
Radio debug tracing is turned on or off, due to start or stop all Dot11 driver tracing. |
31 |
RADIO_RC_PCI_RESET |
Hardware radio reset. PCI bus reset. |
32 |
RADIO_RC_ANT_ALIGN |
Start radio in special mode for directional antenna alignment. |
33 |
RADIO_RC_DFS_NON_ROOT |
Dynamic Frequency Selection reset for non-root radio. |
34 |
RADIO_RC_DFS_NO_CHAN |
Dynamic Frequency Selection reset due to no channels available. |
35 |
RADIO_RC_DFS |
Dynamic Frequency Selection channel change. |
36 |
RADIO_RC_DFS_CHAN_WAIT |
Dynamic Frequency Selection reset waits for available channel. |
37 |
RADIO_RC_IDB_RESET |
Radio interface reset. |
38 |
RADIO_RC_IOS_RELOAD |
Radio reset prior to Cisco IOS® software reload. |
39 |
RADIO_RC_IOS_IP_ADR_CHG |
Radio reset due to Cisco IOS® IP address change. |
40 |
RADIO_RC_REFLASH |
Radio reset prior to the radio reflash. |
41 |
RADIO_RC_CCK_TX |
CCK transmit on dual antennas enable or disable. |
42 |
RADIO_RC_WME |
Enable or disable World Mode IE. |
43 |
RADIO_RC_FCC_TST_STOP |
Stop FCC compliance test mode. |
44 |
RADIO_RC_FCC_TST |
Start FCC compliance test mode. |
45 |
RADIO_RC_CAR_BUSY_TST |
Carrier busy test via the CLI. |
46 |
RADIO_RC_DRIVER_CHK |
Reset if radio becomes disabled. |
47 |
RADIO_RC_COMP_MODE |
FCC test mode interface reset. |
48 |
RADIO_RC_CONFIG |
Radio reset due to configuration change. |
49 |
RADIO_RC_MESH_BACKHAUL |
Clear mesh backhaul. |
50 |
RADIO_RC_MESH_LISTEN |
Set as mesh listener. Radio reset due to enable/disable listening to broadcast on 802.11b (for mesh APs). |
51 |
RADIO_RC_RST_TX_COMP |
Reset on transmit completion. |
52 |
RADIO_RC_DFER_MCAST |
Reset on completion of deferred multicast packets. |
53 |
RADIO_RC_IDB_ENABLE |
Radio interface has been enabled. |
54 |
RADIO_RC_IDB_SHUTDOWN |
Radio interface has been shutdown. |
55 |
RADIO_RC_DOT11_GO_DN |
Cisco IOS® software interface goes down. |
56 |
RADIO_RC_ETHER_GO_DN |
Cisco IOS® ethernet link goes down. |
57 |
RADIO_RC_IF_GO_UP |
Cisco IOS® software interface comes up. |
58 |
RADIO_RC_UPLINK_CLNT_DN |
Uplink client goes away. |
59 |
RADIO_RC_UPLINK_CLNT_UP |
Uplink client comes up. |
60 |
RADIO_RC_SET_CONFIG |
Radio configuration change. |
61 |
RADIO_RC_UPD_PHON_SUP |
Symbol phone extension support has been enabled or disabled. |
62 |
RADIO_RC_SET_CHANNEL |
Radio channel set. Reset while channel from Control and Provisioning of Wireless Access Points (CAPWAP) is set. |
63 |
RADIO_RC_HANDLE_UA |
Universal Access (Mesh) is disabled. |
64 |
RADIO_RC_RLDP_START |
Rogue Location Discovery Protocol start. |
65 |
RADIO_RC_RLDP_START |
Rogue Location Discovery Protocol stop. |
66 |
RADIO_RC_DFS_DEBUG |
Dynamic Frequency Selection debug mode. Reset due to test Dynamic Frequency Selection (DFS) command. |
67 |
RADIO_RC_HOSTNAME_CHG |
Hostname change after association. |
68 |
RADIO_RC_CMD_ROUTINE |
Radio interface reset from command routines. Reset while station_role/beamforming/Space-Time Block Coding (STBC) CLI commands are configured. |
69 |
RADIO_RC_EXIT_LOW_PWR |
Radio exits inline Cisco Discovery Protocol (CDP) low power mode holddown. |
70 |
RADIO_FC_FREQ_CMD_TO |
Frequent command timeouts occur on the radio. Radio command timeouts are more than threshold [10 timeouts]. |
71 |
RADIO_RC_NO_REPORT |
Indicates that while the radio state is updated on controller, no reset is reported. |
72 |
RADIO_RC_INIT |
--not used-- |
73 |
RADIO_FC_TX_DONE |
Bad Tx done (or) bad off channel done. |
74 |
RADIO_FC_RX_INPROG_PTR |
Bad receive in progress pointer when you receive a packet from radio. |
75 |
RADIO_RC_PROM_SERV |
Reset while promiscous mode serving channel is set. |
76 |
RADIO_FC_BAD_TXE_PTR |
Bad Tx pointer. |
77 |
RADIO_FC_RX_RING_INDEX |
Bad Rx ring index. |
78 |
RADIO_FC_TX_STUCK_462 |
--not used-- |
79 |
RADIO_FC_IFACE_BUS_DOWN |
Radio interface bus down. |
80 |
RADIO_FC_TX_CMPL_PAK |
Wrong freeing of Tx completed packet. |
81 |
RADIO_RC_RST_OFFC_COMP |
Offchannel in prog is completed [zero] while radio waits to be stoppped. |
82 |
RADIO_FC_PAK_POISON |
--not used-- |
83 |
RADIO_FC_EU_STUCK_738 |
Encryption engine stuck specific to 8864 radio chipset. |
84 |
RADIO_FC_BEACON_STUCK |
Beacons not transmitted for last 10 minutes. |
85 |
RADIO_FC_BAD_DTX_IN_Q |
Bad packet in transmit queue. |
86 |
RADIO_FC_INFINITE_LOOP |
Debug code reset [Cisco bug ID CSCul63678]- infinite loop detected with Tx requeue client. |
87 |
RADIO_FC_PREFETCH |
DMA engine locked [War for Cisco bug ID CSCui54586 / BZ868]. |
88 |
RADIO_RC_DEAUTH_COMPL |
Deauth client completed. |