There is a reported problem with calls that originate from NetMeeting or a similar third party H.323 devices through a Cisco IOS® gateway to the Public Switched Telephone Network (PSTN) using ISDN. These calls fail during the setup stage. This issue is commonly seen after a Cisco IOS software upgrade is performed on the gateway.
The bearer capability (bearer cap) is an ISDN Layer 3 service indication that defines the characteristics of a given call. The bearer cap of a call is indicated in the Q.931 SETUP message and it is used to distinguish among the different types of voice and data calls.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions.
Refer to the Cisco Technical Tips Conventions for more information on document conventions.
In this case, calls fail because the bearer cap in the ISDN Q.931 SETUP message incorrectly indicates that the Information Transfer Capability is set for Unrestricted Digital Information. The reason this occurs is because the originating H.323 device sets the bearer cap in the H.225 SETUP message for Unrestricted Digital Information. The gateway transparently passes that information to the ISDN switch/PBX in the Q.931 SETUP message. The Switch/PBX is unable to handle this bearer cap and rejects the call.
In earlier Cisco IOS Software releases, the gateway overwrites the bearer cap to indicate speech/audio. However, in later releases, the gateway does not overwrite the bearer cap.
Common bearer caps for voice calls are shown in the first four rows of this table. The remaining three rows show common bearer caps that can cause a call that originates from a third party H.323 device to fail.
This table summarizes some common bearer caps:
Bearer Cap | Information Transfer Capability | User Information Layer 1 Protocol |
---|---|---|
0x8090A2 | Speech | G.711 u-Law Speech |
0x8090A3 | Speech | G.711 A-law |
0x9090A2 | 3.1 KHz Audio | G.711 u-Law Speech |
0x9090A3 | 3.1 KHz Audio | G.711 A-law |
0x8890A2 | Unrestricted digital information | G.711 u-Law Speech |
0x8890A3 | Unrestricted digital information | G.711 A-law |
0x8890 | Unrestricted digital information | 64 Kbps (64k data call) |
This is an example of a debug isdn q931 output that shows a failed call. It indicates that the switch/PBX clears the call immediately after the CALL PROCEEDING message. The DISCONNECT message cause code can vary. Common cause codes include Invalid information element contents and Incompatible destination.
!--- Action: A NetMeeting call is placed !--- to the PSTN through a Cisco IOS gateway. !--- Outgoing Q.931 SETUP message. Aug 8 19:29:59.546: ISDN Se0:23: TX -> SETUP pd = 8 callref = 0x0001 Aug 8 19:29:59.546: Bearer Capability i = 0x8890A2 !--- Bearer cap indicates the call carries the "Unrestricted Digital Information" !--- transfer capability. Aug 8 19:29:59.550: Channel ID i = 0xA98397 Aug 8 19:29:59.550: Calling Party Number i = 0x00, 0x80, '3555', Plan:Unknown, Type:Unknown Aug 8 19:29:59.550: Called Party Number i = 0x80, '95551212, Plan:Unknown, Type:Unknown Aug 8 19:29:59.610: ISDN Se0:23: RX <- CALL_PROC pd = 8 callref = 0x8001 Aug 8 19:29:59.610: Channel ID i = 0xA98397 Aug 8 19:29:59.806: ISDN Se0:23: RX <- DISCONNECT pd = 8 callref = 0x8001 !--- Call is cleared by the switch or PBX. Aug 8 19:29:59.810: Cause i = 0x82E4 - Invalid information element contents Aug 8 19:29:59.814: ISDN Se0:23: TX -> RELEASE pd = 8 callref = 0x0001 Aug 8 19:29:59.850: ISDN Se0:23: RX <- RELEASE_COMP pd = 8 callref = 0x81 !--- Call is cleared for the cause Incompatible destination. Aug 8 20:30:11.820: Cause i = 0x80D8 - Incompatible destination Aug 8 20:30:11.836: ISDN Se0:23: TX -> RELEASE pd = 8 callref = 0x0001 Aug 8 20:30:11.852: ISDN Se0:23: RX <- RELEASE_COMP pd = 8 callref = 0x81
Configure the originating H.323 device to set the appropriate bearer cap in the H.225 SETUP message.
If the originating H.323 device cannot be reconfigured, modify the Cisco IOS gateway configuration to overwrite the bearer cap in the ISDN Q.931 SETUP message. Use the voice-port configuration mode command bearer-cap to set it for speech or 3100 hz audio as appropriate.
!--- This is an example of how to configure the bearer cap parameter !--- on a Cisco AS5300. esc-5300-2(config)#voice-port 0:D esc-5300-2(config-voiceport)#bearer-cap ? 3100hz enable 3100hz speech enable speech esc-5300-2(config-voiceport)#bearer-cap speech !--- Sample output of the IOS configuration !--- <some output omitted>. ! voice-port 0:D bearer-cap Speech !
Note: If you run Cisco IOS Software Release 12.2(11)T, where H.323 version 4 runs on your router, you can experience trouble with NetMeeting. The details are enclosed in Cisco bug ID CSCdw49975 (registered customers only) .
Revision | Publish Date | Comments |
---|---|---|
1.0 |
02-Feb-2006 |
Initial Release |