Contents

Introduction

Prerequisites

Requirements

Components Used

Conventions

Background Information

Configure

Network Diagram

Configurations

Configuration using ASDM

Verify

Troubleshoot

Troubleshooting Commands

Related Information

Introduction

This document demonstrates how to configure an IPsec tunnel from PIX Security Appliance 7.x and later or the Adaptive Security Appliance (ASA) with one internal network to a 2611 router that runs a crypto image. Static routes are used for simplicity.

Refer to Configuring IPSec - Router to PIX for more information about a LAN-to-LAN tunnel configuration between a router and the PIX.

Refer to LAN-to-LAN IPSec Tunnel Between the Cisco VPN 3000 Concentrator and PIX Firewall Configuration Example for more information about a LAN-to-LAN tunnel configuration between the PIX Firewall and Cisco VPN 3000 Concentrator.

Refer to IPsec Tunnel Between PIX 7.x and VPN 3000 Concentrator Configuration Example in order to learn more about the scenario where the LAN-to-LAN tunnel is between the PIX and VPN Concentrator.

Refer to PIX/ASA 7.x Enhanced Spoke-to-Client VPN with TACACS+ Authentication Configuration Example in order to learn more about the scenario where the LAN-to-LAN tunnel between the PIXes also allows for a VPN Client to access the spoke PIX through the hub PIX.

Refer to SDM: Site-to-Site IPsec VPN Between ASA/PIX and an IOS Router Configuration Example in order to learn more about the same scenario where the PIX/ASA Security Appliance runs software version 8.x.

Refer to Configuration Professional: Site-to-Site IPsec VPN Between ASA/PIX and an IOS Router Configuration Example in order to learn more about the same scenario where the ASA-related configuration is shown using ASDM GUI and the Router-related configuration is shown using Cisco CP GUI.

Prerequisites

Requirements

There are no specific requirements for this document.

Components Used

The information in this document is based on these software and hardware versions:

- PIX-525 with PIX Software version 7.0

- Cisco 2611 router with Cisco IOS® Software Release 12.2(15)T13

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Refer to the Cisco Technical Tips Conventions for more information on document conventions.

Background Information

On the PIX, the access-list and nat 0 commands work together. When a user on the 10.1.1.0 network goes to the 10.2.2.0 network, the access list is used to permit the 10.1.1.0 network traffic to be encrypted without Network Address Translation (NAT). On the router, the route-map and access-list commands are used to permit the 10.2.2.0 network traffic to be encrypted without NAT. However, when those same users go anywhere else, they are translated to the 172.17.63.230 address through Port Address Translation (PAT).

These are the configuration commands required on the PIX Security Appliance in order for traffic not to run through PAT over the tunnel, and traffic to the Internet to run through PAT

access-list nonat permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0

nat (inside) 0 access-list nonat

nat (inside) 1 10.1.1.0 255.255.255.0 0 0

Configure

In this section, you are presented with the information to configure the features described in this document.

Note: Use the Command Lookup Tool (registered customers only) to obtain more information on the commands used in this section.

Network Diagram

This document uses this network setup:

Configurations

These configuration examples are for the command line interface. See the Configuration using Adaptive Security Device Manager (ASDM) section of this document if you prefer to configure using ASDM.

- Headquarters PIX

- Branch Router

Headquarters PIX

HQPIX(config)#show run

PIX Version 7.0(0)102

names

!

interface Ethernet0

description WAN interface

nameif outside

security-level 0

ip address 172.17.63.229 255.255.255.240

!

interface Ethernet1

nameif inside

security-level 100

ip address 10.1.1.1 255.255.255.0

!

interface Ethernet2

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet3

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet4

shutdown

no nameif

no security-level

no ip address

!

interface Ethernet5

shutdown

no nameif

no security-level

no ip address

!

enable password 8Ry2YjIyt7RRXU24 encrypted

passwd 2KFQnbNIdI.2KYOU encrypted

hostname HQPIX

domain-name cisco.com

ftp mode passive

clock timezone AEST 10

access-list Ipsec-conn extended permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0

access-list nonat extended permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0

pager lines 24

logging enable

logging buffered debugging

mtu inside 1500

mtu outside 1500

no failover

monitor-interface inside

monitor-interface outside

asdm image flash:/asdmfile.50073

no asdm history enable

arp timeout 14400

nat-control

global (outside) 1 interface

nat (inside) 0 access-list nonat

nat (inside) 1 10.1.1.0 255.255.255.0

access-group 100 in interface inside

route outside 0.0.0.0 0.0.0.0 172.17.63.230 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server RADIUS protocol radius

aaa-server partner protocol tacacs+

username cisco password 3USUcOPFUiMCO4Jk encrypted

http server enable

http 10.1.1.2 255.255.255.255 inside

no snmp-server location

no snmp-server contact

snmp-server community public

snmp-server enable traps snmp

crypto ipsec transform-set avalanche esp-des esp-md5-hmac

crypto ipsec security-association lifetime seconds 3600

crypto ipsec df-bit clear-df outside

crypto map forsberg 21 match address Ipsec-conn

crypto map forsberg 21 set peer 172.17.63.230

crypto map forsberg 21 set transform-set avalanche

crypto map forsberg interface outside

isakmp identity address

isakmp enable outside

isakmp policy 1 authentication pre-share

isakmp policy 1 encryption 3des

isakmp policy 1 hash sha

isakmp policy 1 group 2

isakmp policy 1 lifetime 86400

isakmp policy 65535 authentication pre-share

isakmp policy 65535 encryption 3des

isakmp policy 65535 hash sha

isakmp policy 65535 group 2

isakmp policy 65535 lifetime 86400

telnet timeout 5

ssh timeout 5

console timeout 0

tunnel-group 172.17.63.230 type ipsec-l2l

tunnel-group 172.17.63.230 ipsec-attributes

pre-shared-key *

!

class-map inspection_default

match default-inspection-traffic

!

!

policy-map asa_global_fw_policy

class inspection_default

inspect dns maximum-length 512

inspect ftp

inspect h323 h225

inspect h323 ras

inspect netbios

inspect rsh

inspect rtsp

inspect skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect tftp

inspect sip

inspect xdmcp

inspect http

!

service-policy asa_global_fw_policy global

Cryptochecksum:3a5851f7310d14e82bdf17e64d638738

: end

SV-2-8#

Branch Router

BranchRouter#show run

Building configuration...

Current configuration : 1719 bytes

!

! Last configuration change at 13:03:25 AEST Tue Apr 5 2005

! NVRAM config last updated at 13:03:44 AEST Tue Apr 5 2005

!

version 12.2

service timestamps debug datetime msec

service timestamps log uptime

no service password-encryption

!

hostname BranchRouter

!

logging queue-limit 100

logging buffered 4096 debugging

!

username cisco privilege 15 password 0 cisco

memory-size iomem 15

clock timezone AEST 10

ip subnet-zero

!

!

!

ip audit notify log

ip audit po max-events 100

!

!

!

crypto isakmp policy 11

encr 3des

authentication pre-share

group 2

crypto isakmp key cisco123 address 172.17.63.229

!

!

crypto ipsec transform-set sharks esp-des esp-md5-hmac

!

crypto map nolan 11 ipsec-isakmp

set peer 172.17.63.229

set transform-set sharks

match address 120

!

!

!

!

!

!

!

!

!

!

no voice hpi capture buffer

no voice hpi capture destination

!

!

mta receive maximum-recipients 0

!

!

!

!

interface Ethernet0/0

ip address 172.17.63.230 255.255.255.240

ip nat outside

no ip route-cache

no ip mroute-cache

half-duplex

crypto map nolan

!

interface Ethernet0/1

ip address 10.2.2.1 255.255.255.0

ip nat inside

half-duplex

!

ip nat pool branch 172.17.63.230 172.17.63.230 netmask 255.255.255.0

ip nat inside source route-map nonat pool branch overload

no ip http server

no ip http secure-server

ip classless

ip route 10.1.1.0 255.255.255.0 172.17.63.229

!

!

!

access-list 120 permit ip 10.2.2.0 0.0.0.255 10.1.1.0 0.0.0.255

access-list 130 deny ip 10.2.2.0 0.0.0.255 10.1.1.0 0.0.0.255

access-list 130 permit ip 10.2.2.0 0.0.0.255 any

!

route-map nonat permit 10

match ip address 130

!

call rsvp-sync

!

!

mgcp profile default

!

dial-peer cor custom

!

!

!

!

!

line con 0

line aux 0

line vty 0 4

login

!

!

end

Configuration using ASDM

This example demonstrates how to configure the PIX using the ASDM GUI. A PC with a browser and IP address 10.1.1.2 is connected to the inside interface e1 of the PIX. Ensure http is enabled on the PIX.

This procedure illustrates the ASDM configuration of the Headquarters PIX.

1. Connect the PC to the PIX and choose a download method.

ASDM loads the existing configuration from the PIX.

This window provides monitoring instruments and menus.

2. Select Configuration > Features > Interfaces and select Add for new interfaces or Edit for an existing configuration.

3. Select the security options for the inside interface.

4. In the NAT configuration, encrypted traffic is NAT-exempt and all other traffic is NAT/PAT to the outside interface.

5. Select VPN >General > Tunnel Group and enable a Tunnel Group

6. Select VPN > IKE > Global Parameters and enable IKE on the outside interface.

7. Select VPN > IKE > Policies and choose the IKE policies.

8. Select VPN > IPsec > IPsec Rules and choose IPsec for the local tunnel and remote addressing.

9. Select VPN > IPsec > Tunnel Policy and choose the tunnel policy.

10. Select VPN > IPsec > Transform Sets and choose a Transform set.

11. Select Routing > Routing > Static Route and choose a static route to gateway router. In this example, the static route points to the remote VPN peer for simplicity.

Verify

Use this section to confirm that your configuration works properly.

The Output Interpreter Tool (registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of show command output.

- show crypto ipsec sa—Shows the phase 2 security associations.

- show crypto isakmp sa—Shows the phase 1 security associations.

Troubleshoot

You can use ASDM to enable logging and to view the logs.

- Select Configuration > Properties > Logging > Logging Setup, choose Enable Logging and click Apply to enable logging.

- Select Monitoring > Logging > Log Buffer > On Logging Level, choose Logging Buffer, and click View to view the logs.

Troubleshooting Commands

The Output Interpreter Tool (registered customers only) (OIT) supports certain show commands. Use the OIT to view an analysis of show command output.

Note: Refer to Important Information on Debug Commands before you use debug commands.

- debug crypto ipsec—Shows the IPsec negotiations of phase 2.

- debug crypto isakmp—Shows the ISAKMP negotiations of phase 1.

- debug crypto engine—Shows the traffic that is encrypted.

- clear crypto isakmp—Clears the security associations related to phase 1.

- clear crypto sa—Clears the security associations related to phase 2.

- debug icmp trace—Shows whether ICMP requests from the hosts reach the PIX. You need to add the access-list command to permit ICMP in your configuration in order to run this debug.

- logging buffer debugging—Shows connections being established and denied to hosts that go through the PIX. The information is stored in the PIX log buffer and you can see the output with the show log command.

Related Information

- Most Common L2L and Remote Access IPSec VPN Troubleshooting Solutions

- Cisco PIX Firewall Software

- Cisco Secure PIX Firewall Command References

- Security Product Field Notices (including PIX)

- Requests for Comments (RFCs)