Contents

Introduction

Requirements

Components Used

Procedure

Introduction

This document describes CUSP upgrade from 8.5.1 to 8.5.XX.

Contributed by Mayur Vyas, Cisco TAC Engineer.

Edited by Sahar Modares, Cisco TAC Engineer.

Requirements

Cisco recommands that you have knowledge of these components:

CUSP

Components Used

CUSP 8.5.1

Procedure

Here are the steps to upgrade CUSP to 8.5.9.

Step 1. Take a backup of your current cnfguration. Here is a link to backup CUSP:

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusp/rel8_5/OLH/gui_config_olh/core_config_backup.html

Step 2. Verify installed Hardware (HW) Module.

SYD_TAC_3945#sh inventory

NME-CUSP-522 or

SM-SRE-700 and SM-SRE-900

Step 3. Download comptabile software. You can use this link to download the software.

https://software.cisco.com/download/release.html?mdfid=283138869&catid=278875240&softwareid=282707924&release=8.5.9&relind=AVAILABLE&rellifecycle=GD&reltype=latest

and download helper file form here:

https://software.cisco.com/download/release.html?mdfid=283138869&catid=278875240&softwareid=282707918&release=8.5.9&relind=AVAILABLE&rellifecycle=&reltype=latest

Step 4. Ensure you have downloaded these files in File Transer Protcol (FTP) and Trivial File Transfer Protocol (TFTP) servers's root path.

For NME, download these file:

cusp-full-k9.nmx.8.5.9.prt1

cusp-installer-k9.nmx.8.5.9.prt1

cusp-k9.nmx.8.5.9.pkg

cusp-helper.nmx.8.5.9

For SRE, download these files:

cusp-full-k9.sme.8.5.9.prt1

cusp-installer-k9.sme.8.5.9.prt1

cusp-k9.sme.8.5.9.key

cusp-k9.sme.8.5.9.pkg

cusp-k9.sme.8.5.9.pkg.install.sre

cusp-k9.sme.8.5.9.pkg.install.sre.header

cusp-helper.sme.8.5.9

Step 5. Open 2 putty windows.

One for module to monitor installation

One for router to install software

Step 6. Load the file on the module in router putty session.

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusp/rel8_5/install/cusp_install/install_cusp.html#wp1164262

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusp/rel8_5/install/cusp_install.pdf

Router# service-module sm 1/0 install url  ftp://myuser:mypasswd@myhost/my-download-path/cusp-k9.nmxsme.8.5.9.pkg

e.g. ftp://cisco:cisco/10.66.74.191/cusp-k9.<nmxsme>.8.5.9.pkg

Tip: If you run into any issues during installation, enable debug sre-install all on the router.

Step 7. Restore the configuration. Navigate to Administration > Backup / Restore > Start Restore and restore configuration.

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusp/rel8_5/OLH/gui_config_olh/core_config_backup.html

For further informaiton refer to this link:

http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusp/rel8_5/install/cusp_install/migrating.html