CVSS:3.1/AV:N/AC:L/PR:L/UI:N/S:C/C:N/I:N/A:H/E:X/RL:X/RC:X
-
A vulnerability in the Simple Network Management Protocol (SNMP) punt handling function of Cisco cBR-8 Converged Broadband Routers could allow an authenticated, remote attacker to overload a device punt path, resulting in a denial of service (DoS) condition.
This vulnerability is due to the punt path being overwhelmed by large quantities of SNMP requests. An attacker could exploit this vulnerability by sending a large number of SNMP requests to an affected device. A successful exploit could allow the attacker to overload the device punt path, resulting in a DoS condition.
Cisco has released software updates that address this vulnerability. There are workarounds that address this vulnerability.
This advisory is available at the following link:
https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-cbr8snmp-zGjkZ9FcThis advisory is part of the September 2021 release of the Cisco IOS and IOS XE Software Security Advisory Bundled Publication. For a complete list of the advisories and links to them, see Cisco Event Response: September 2021 Semiannual Cisco IOS and IOS XE Software Security Advisory Bundled Publication.
-
Vulnerable Products
This vulnerability affects Cisco cBR-8 Converged Broadband Routers if they are running a vulnerable release of Cisco IOS XE Software and have the SNMP server feature enabled.
For information about which Cisco software releases are vulnerable, see the Fixed Software section of this advisory.
Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.
Cisco has confirmed that this vulnerability does not affect the following Cisco products:
- IOS Software
- IOS XR Software
- Meraki products
- NX-OS Software
-
With the fix of Cisco Bug ID CSCvw60229, as described in this advisory, a new SNMP-specific punt-cause has been introduced. The default rate is 512 packets per second. This can be tuned using the platform punt-policer cable-snmp {rate} command. For more information, see the platform punt-policer section of Cisco CMTS Cable Command Reference.
The SNMP packets could be sent over either IPv4 or IPv6. Configurations for both SNMP versions 2c and 3 are affected. This vulnerability applies to SNMP requests that have valid SNMP community strings or credentials, depending on the SNMP version.
-
There is a workaround that addresses this vulnerability.
Ensure that only trusted systems can poll the Cisco cBR-8 Routers and limit those systems to 500 pps or less, as shown in the following example:
!
ip access-list extended 100
10 permit udp host 10.10.10.10 host 192.168.1.1 eq snmp
ip access-list extended 101
10 permit udp any host 192.168.1.1 eq snmp
!
class-map match-any snmp_trusted
match access-group 100
class-map match-any snmp_untrusted
match access-group 101
!
policy-map copp_policy
! rate-limit trusted SNMP pkts to 500 pps
class snmp_trusted
police rate 500 pps conform-action transmit exceed-action drop
! drop all untrusted SNMP pkts (both actions are drop)
class snmp_untrusted
police rate 1 pps conform-action drop exceed-action drop
class class-default
!
control-plane
service-policy input copp_policy
Where 10.10.10.10 is the IPv4 address of the SNMP Client and
192.168.1.1 is the IPv4 address on the cBR-8 that the SNMP
requests are sent to.While this workaround has been deployed and was proven successful in a test environment, customers should determine the applicability and effectiveness in their own environment and under their own use conditions. Customers should be aware that any workaround or mitigation that is implemented may negatively impact the functionality or performance of their network based on intrinsic customer deployment scenarios and limitations. Customers should not deploy any workarounds or mitigations before first evaluating the applicability to their own environment and any impact to such environment.
-
Cisco has released free software updates that address the vulnerability described in this advisory. Customers may only install and expect support for software versions and feature sets for which they have purchased a license. By installing, downloading, accessing, or otherwise using such software upgrades, customers agree to follow the terms of the Cisco software license:
https://www.cisco.com/c/en/us/products/end-user-license-agreement.htmlAdditionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.
When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page, to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
Customers Without Service Contracts
Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco TAC: https://www.cisco.com/c/en/us/support/web/tsd-cisco-worldwide-contacts.html
Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.
Cisco IOS and IOS XE Software
To help customers determine their exposure to vulnerabilities in Cisco IOS and IOS XE Software, Cisco provides the Cisco Software Checker to identify any Cisco Security Advisories that impact a specific software release and the earliest release that fixes the vulnerabilities described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities described in all the advisories identified (“Combined First Fixed”).
Customers can use the Cisco Software Checker to search advisories in the following ways:
- Choose the software and one or more releases
- Upload a .txt file that includes a list of specific releases
- Enter the output of the show version command
After initiating a search, customers can customize the search to include all Cisco Security Advisories, a specific advisory, or all advisories in the most recent bundled publication.
Customers can also use the following form to determine whether a release is affected by any Cisco Security Advisory by entering a Cisco IOS or IOS XE Software release—for example, 15.1(4)M2 or 3.13.8S:
By default, the Cisco Software Checker includes results only for vulnerabilities that have a Critical or High Security Impact Rating (SIR). To include results for Medium SIR vulnerabilities, customers can use the Cisco Software Checker on Cisco.com and check the Medium check box in the drop-down list under Impact Rating when customizing a search.
-
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
-
This vulnerability was found during the resolution of a Cisco TAC support case.
-
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
-
Version Description Section Status Date 1.0 Initial public release. — Final 2021-SEP-22
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.