CVSS:3.1/AV:N/AC:H/PR:N/UI:N/S:C/C:N/I:N/A:H/E:X/RL:X/RC:X
-
A vulnerability in the IPv6 DHCP (DHCPv6) client module of Cisco Adaptive Security Appliance (ASA) Software, Cisco Firepower Threat Defense (FTD) Software, Cisco IOS Software, and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device.
This vulnerability is due to insufficient validation of DHCPv6 messages. An attacker could exploit this vulnerability by sending crafted DHCPv6 messages to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition.
Note: To successfully exploit this vulnerability, the attacker would need to either control the DHCPv6 server or be in a man-in-the-middle position.
Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability.
This advisory is available at the following link:
https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-asaftdios-dhcpv6-cli-Zf3zTvThis advisory is part of the March 2023 release of the Cisco IOS and IOS XE Software Security Advisory Bundled Publication. For a complete list of the advisories and links to them, see Cisco Event Response: March 2023 Semiannual Cisco IOS and IOS XE Software Security Advisory Bundled Publication.
-
Vulnerable Products
At the time of publication, this vulnerability affected the following Cisco products if they had the DHCPv6 client feature enabled:
- ASA Software
- FTD Software
- IOS Software
- IOS XE Software
For information about which Cisco software releases were vulnerable at the time of publication, see the Fixed Software section of this advisory. See the Details section in the bug ID(s) at the top of this advisory for the most complete and current information.
Determine the DHCPv6 Client Configuration
To determine the DHCPv6 client configuration, use the show running-config CLI command. In the output, look for interfaces that have both the ipv6 enable command and the ipv6 address dhcp command. If there is at least one interface that has both IPv6 enabled and the DHCPv6 client feature enabled, the device is affected by this vulnerability.
The following example shows the output of the show running-config command on a device that has both IPv6 and the DHCPv6 client feature enabled under interface GigabitEthernet0/0:
firewall# show running-config
.
.
.
interface GigabitEthernet0/0
.
.
.
ipv6 address dhcp
ipv6 enable
.
.
.Note: On devices that are running Cisco IOS or IOS XE Software, also look for the ipv6 unicast-routing command in global configuration mode. If this command is missing, the devices are not processing any IPv6 traffic and are not affected, even if they have IPv6 and the DHCPv6 client feature enabled under any interface.
Products Confirmed Not Vulnerable
Only products listed in the Vulnerable Products section of this advisory are known to be affected by this vulnerability.
Cisco has confirmed that this vulnerability does not affect the following Cisco products:
- Firepower Management Center (FMC) Software
- FXOS Software
- IOS XR Software
- Meraki products
- Next-Generation Intrusion Prevention System (NGIPS) Software
- NX-OS Software
-
There are no workarounds that address this vulnerability.
-
When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories page, to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
Cisco ASA, FMC, and FTD Software
To help customers determine their exposure to vulnerabilities in Cisco ASA, FMC, and FTD Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities that are described in all the advisories that the Software Checker identifies (“Combined First Fixed”).
To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to search for vulnerabilities that affect a specific software release. To use the form, follow these steps:
- Choose which advisories the tool will search—all advisories, only advisories with a Critical or High Security Impact Rating (SIR), or only this advisory.
- Choose the appropriate software.
- Choose the appropriate platform.
- Enter a release number—for example, 9.16.2.11 for Cisco ASA Software or 6.6.7 for Cisco FTD Software.
- Click Check.
Additional Resources
For help determining the best Cisco ASA, FMC, or FTD Software release, see the following Recommended Releases documents. If a security advisory recommends a later release, Cisco recommends following the advisory guidance.
Cisco ASA Compatibility
Cisco Secure Firewall ASA Upgrade Guide
Cisco Secure Firewall Threat Defense Compatibility GuideCisco IOS and IOS XE Software
To help customers determine their exposure to vulnerabilities in Cisco IOS and IOS XE Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities that are described in all the advisories that the Software Checker identifies (“Combined First Fixed”).
To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to determine whether a release is affected by any Cisco Security Advisory. To use the form, follow these steps:
- Choose which advisories the tool will search—only this advisory, only advisories with a Critical or High Security Impact Rating (SIR), or all advisories.
- Enter a release number—for example, 15.9(3)M2 or 17.3.3.
- Click Check.
-
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
-
This vulnerability was found during internal security testing by X.B. of the Cisco Advanced Security Initiatives Group (ASIG).
-
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
-
Version Description Section Status Date 1.0 Initial public release. — Final 2023-MAR-22
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.