-
Cisco Catalyst software permits unauthorized access to the enable mode in the 7.5(1) release. Once initial access is granted, access can be obtained for the higher level "enable" mode without a password. This problem is resolved in version 7.6(1). Customers with vulnerable releases are urged to upgrade as soon as possible.
This issue is documented in Cisco Bug ID CSCea42030.
This advisory is posted at https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20030424-catos.
-
All users of Cisco Catalyst 4000, 6000, and 6500 with the Catalyst OS software version 7.5(1) only.
No other releases of Cisco Catalyst OS software are affected by this vulnerability. Additionally, Catalyst hardware running Cisco IOS® software is not affected by this vulnerability.
No other Cisco products are affected by this vulnerability.
-
Anyone who can obtain command line access to an affected switch can bypass password authentication to obtain "enable" mode access without knowledge of the "enable" password. If local user authentication is enabled, any username can be used to gain access to the switch without a valid password. This same local user could then enter enable without a valid password.
Command line access is provided through the console, telnet access, or ssh access methods; http access mode is not affected.
This problem was introduced with the local user authentication feature in software version 7.5(1), and is corrected in version 7.6(1).
This vulnerability is described in Cisco bugid CSCea42030
-
Use of AAA authentication configurations will eliminate this vulnerability unless configured for fallback to local authentication. AAA configuration information and examples are provided in Configuring TACACS+, RADIUS, and Kerberos on Cisco Catalyst Switches, available at: http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a0080094ea4.shtml.
Strictly limiting telnet and/or ssh access to the device will prevent the initial connection required to exploit this vulnerability. Telnet and/or ssh access can be controlled with the following command set:
set ip permit <address> <mask> telnet set ip permit <address> <mask> ssh set ip permit enable
This command set will deny all traffic not specified in the permit statements for each protocol.
Additionally, out-of-band management solutions and isolated management VLAN configurations can help mitigate this vulnerability by limiting the initial access necessary for exploitation.
-
When considering software upgrades, also consult http://www.cisco.com/go/psirt and any subsequent advisories to determine exposure and a complete upgrade solution.
In all cases, customers should exercise caution to be certain the devices to be upgraded contain sufficient memory and that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, contact the Cisco Technical Assistance Center (TAC) or your contracted maintenance provider for assistance.
his vulnerability is fixed in Catalyst OS version 7.6(1) and later
-
The Cisco PSIRT is not aware of any public announcements or malicious use of the vulnerability described in this advisory.
This vulnerability was reported to Cisco by Marco P. Rodrigues.
-
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
-
Revision 1.0
24-April-2003
Initial public release.
Revision 1.1
24-April-2003
Added clarification under "Exploitation and Public Announcements" section.
Revision 1.2
25-April-2003
Added customer name that reported issue, corrected details regarding exploitation, and updated workaround information on AAA services.
Revision 1.3
07-May-2003
Added link to AAA configuration examples.
Revision 1.4
05-January-2005
Updated the Configuring TACACS+, RADIUS, and Kerberos on Cisco Catalyst Switches document URL in the Workarounds section.
-
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A stand-alone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy, and may lack important information or contain factual errors. The information in this document is intended for end-users of Cisco products.