The Cisco® Network Convergence System 200 Gbps Hybrid Line Card (Figure 1) provides multirate and protocol flexibility (OTN, Carrier Ethernet) to enable multilayer technology convergence for next-generation Converged Packet Optical Transport Systems.
The NCS 4000 Multilayer Converged LC provides the ability to deploy OTN packets at 10 Gbps and 100 Gbps rates using an agnostic switch fabric to switch up to 200 Gbps I/O capacity.
OTN provides robust transport services that use many of the benefits of SONET/SDH such as resiliency and performance monitoring, while adding enhanced multirate capabilities in support of packet traffic, plus the transparency required by DWDM networks. OTN is the ideal technology to bridge the gap between next-generation IP and legacy time-division multiplexing (TDM) networks by acting as a converged transport layer for newer packet-based and existing TDM services. (See Table 1.)
Table 1. Features and Benefits
Feature |
Benefit |
Technology agility |
Combines multiple network elements into one Agnostic switch fabric for I/O diversity |
Operational agility |
Faster time to market for deploying services across layers to address evolving market needs |
Scalability |
Multichassis capability to address bandwidth requirements up to 153.6 Tbps Multiple chassis footprint for LC |
Cisco IOS® XR Software |
Industry-leading software stability |
Converged Packet-Optical Networks
Next-generation optical transport networks are evolving toward multilayer, multirate, and converged networks to provide efficient transport and economies of scale to enable service providers to deploy cloud data center interconnect while maintaining support for legacy networks. Converged packet optical networks enable service providers to deploy transport networks with a faster time to market and time to revenue.
● Combine per-layer (DWDM, OTN, packet) network elements into a single platform.
● Agnostic cell-based switch fabric for I/O diversity
● Virtualized software infrastructure for rapid deployment
● Lower operational expenditure: manage/deploy single network element instead of three
● Technology agility: any combination of OTN, DWDM, and packet
● Statistical multiplexing on a per-ODU basis for improved WAN infrastructure utilization
● Cisco IOS-XR Software for industry-leading stability and functionality
Interfaces
The NCS 4000 2 x 100G, 2 x 10 Gbps Combo line card supports any combination of the following interfaces, up to:
● Ten 10 Gigabit Ethernet interfaces through SFP+ pluggables
● Ten OC-192/STM-64 interfaces through SFP+ pluggables
● Two 100 GigE LAN PHY interfaces through CPAK pluggables
● Two 100 OTU-4 interfaces through CPAK pluggables
The OC192/STM-64 interfaces will be supported over OTN only.
The card is capable of supporting two operational modes
● 2 x 100 Gbps mode: the line card will provide the following interface types with the total I/O capacity of up to 200 Gbps:
◦ 2 x 100 Gbps OTN or 2 x 100 GigE interfaces with no access to the SFP+ interfaces
◦ Twenty 10 GigE interfaces with a 10x10 Gbps breakout cable attached to the 100 Gbps CPAK interfaces
◦ Ten OC-192/STM-64 interfaces on the SFP+ receptacles
● 1 x 100 Gbps, 10 x 10 Gbps SFP+ mode: the line card will provide:
◦ One 100 GigE or 100 GigE OTN CPAK interface
◦ Ten SFP+ receptacles for ten 10 GigE interfaces
◦ Ten SFP+ receptacles for ten STM-64 interfaces
◦ Ten SFP+ receptacles for ten OC-192 interfaces
OTN Support
OTU-1 and OTU-2 ports support generic forward error correction (GFEC). The card is capable of supporting up to 2-level ODU-4, ODU-3, ODU-2, ODU-1, ODU-0, and ODU-Flex switching functions by interconnecting with the centralized agnostic switch fabric. (See Table 2.)
The NCS 4000 2 x 100G, 2 x 10 Gbps Combo line card supports any combination of 100 Gigabit Ethernet and OTU-4 interfaces using Cisco CPAK pluggable transceivers (Figure 2). The Cisco CPAK pluggable transceiver utilizes complementary metal-oxide semiconductor (CMOS) photonics technology to dramatically reduce the size and power consumption of 100 Gbps interfaces while maintaining IEEE and ITU protocol compliance. Two CPAK receptacles are hosted on the faceplate.
Table 2. OTN Line-Card Mapping
Rate |
Mapping |
10 Gigabit Ethernet |
G.Sup43 7.1/G.709 17.2.4: CBR10.3G à OPU2e G.709 17.4: GFP-F à OPU2 G.Sup43 7.3/G.709 17.4.1: GFP-F à Extended OPU |
OC-192/STM-64 |
OC192/STM-64: CBRI CBRB ODU2 AMP/BMP |
100 Gigabit Ethernet |
IEEE 802.3ba |
100 Gigabit OTN |
G.709v3 |
The card supports up to two-level ODU-4, ODU-3, ODU-2, ODU-0, and ODU-Flex nested switching functions by interconnecting with the centralized agnostic switch fabric; 100 Gigabit Ethernet signals are mapped using generic mapping procedure (GMP) over ODU-4 according to ITU-T G.709 v3 (Section 17.7.5).
The 100 Gbps ports a standard G.975 Reed-Solomon FEC algorithm, which can be enabled or disabled through software configuration.
Extending nLight Silicon to the client-facing interface, the client ports use Cisco CPAK pluggable transceivers supporting 100GBASE-SR10, 100GBASE-LR-4, and the OTU-4 equivalent interfaces. The extremely compact dimensions and low power consumption of CPAK enable superb system density of greater than one 100 Gigabit Ethernet transponder per rack unit. (See Figure 3 and Table 3.)
Table 3. Performance Monitoring Parameters
Area |
Parameter Name |
Description |
|
OTN |
OTUk SM |
ODUk PM |
|
BBE-SM |
BBE-PM |
Number of background block errors |
|
BBER-SM |
BBER-PM |
Background block error ratio |
|
ES-SM |
ES-PM |
Number of errored seconds |
|
ESR-SM |
ESR-PM |
Errored seconds ratio |
|
SES-SM |
SES-PM |
Number of severely errored seconds |
|
SESR-SM |
SESR-PM |
Severely errored seconds ratio |
|
UAS-SM |
UAS-PM |
Number of unavailable seconds |
|
FC-SM |
FC-PM |
Number of failure counts |
|
FEC |
Bit errors |
Number of corrected bit errors |
|
Uncorrectable words |
Number of uncorrectable words |
Packet Features
The NCS Converged Packet Optical line card supports packet features as defined in Table 4 on a per-ODU or on a per-interface basis.
Table 4. HW Readiness Feature Set
Functionality |
Featured Mechanism |
Layer 2 transport |
Carrier Ethernet, MPLS |
Layer 2 and Layer 2+ services |
Carrier Ethernet: EPL, EVPL MPLS-TE: P2P circuits (VPWS) |
Ethernet virtual circuit |
IEEE 802.1q, IEEE 802.1ad |
IGP |
OSPF-TE |
Quality of service (per port) |
Policing, queuing/shaping Single-rate, dual-color policer (1R2C) Single-rate, three-color policer (1R3C) Dual-rate, three-color policer (2R3C) |
Ethernet OAM |
IEEE 802.1ag CFM IEEE 802.3ah EFM |
Sync-E |
ITU-T G.8261 ITU-T G.8262 |
Platform Support
Table 5 shows Platform Supported by NCS 4000 2x 100G CPAK 10x10G SFP+ OTN/Packet Line Card.
Table 5. Supported HW Platform and SW Releases
Product Family |
Platforms Supported |
Cisco IOS Software Images (Feature Sets) Supported |
NCS 4000 |
NCS 4016, NCS 4009 |
Cisco IOS XR Software 5.2.4.x onwards |
Product Specifications
Table 6 lists product specifications.
Table 6. Product Specifications at System Level
Parameter |
Scale |
Total number of 10 GigE interfaces |
320 |
Total number of OC-192 interfaces |
320 |
Total number of STM-64 interfaces |
320 |
Total number of 100 GigE interfaces |
32 |
Total number of 100 GigE OTN interfaces |
32 |
Total number of Ethernet virtual circuits (EVCs) |
16,000 |
Total number of MPLS LSPs |
4000 |
Total number of MPLS pseudowire (VPWS) |
16,000 |
Total number of IEEE 802.1ag CFM MEPs |
16,000 |
Total number of IEEE 802.3ah EFM sessions |
320 |
MAC address table size (chassis) |
256,000 |
Total number of QoS policies (1R2C) |
16.000 |
Cisco NCS 4000 Line Cards use pluggable transceivers to provide a pay-as-you-grow model and flexibility to support different reaches. Table 7 summarizes supported pluggables.
Table 7. Cisco NCS 4000 Pluggable Interfaces
Pluggable |
Rate and Reach |
Product ID |
SFP+ |
10 GE SR/SW |
ONS-SC+-10G-SR= |
10 GE LR/LW OC-192 SR STM-64 I-64.1 OTU-2 P1I1 2D1 |
ONS-SC+-10G-LR= |
|
10 GE ER/EW OC-192 IR-2 STM-64 S-64.2 OTU-2 P1S1-2D2 |
ONS-SC+-10G-ER= |
|
10 GE ZR OC192 LR-2 STM-64 L-64.2 OTU-2 P1L1-2D2 |
ONS-SC+-10G-ZR= |
|
C-band tunable |
ONS-SC+-10G-C= |
|
CPAK |
100 GE SR10 |
CPAK-100G-SR10= |
100 GE LR4 OTU-4 4I1-9D1F |
CPAK-100G-LR= |
|
OTU-2 P1L1-2D2 10GE LR |
CPAK-10X10G-LR= |
Physical Specifications
Table 8 lists the power consumption, weight, and dimensions of NCS 4000 Converged Packet Optical Line Cards.
Table 8. Cisco NCS 4000 Physical Specifications
Unit |
Maximum Power (W) |
Typical Power (W) |
Weight |
Dimensions (H x W x D) |
20x100 Gbps, 10 Gbps Combo Converged Line Card |
246 |
290 |
5.5 lbs (2.5 kg) |
10 x 12.5 x 1.55 in. (254 x 317.5 x 39.37 mm) |
MTBF |
345570 hrs |
|||
Weight |
2.98 kg (6.57 lbs) |
System Requirements
Table 9 describes physical specifications.
Table 9. Cisco NCS 4000 Physical Specifications
Disk space |
32 Gbps |
Hardware |
Dual RP, fabric |
Memory |
2 Gbps RAM |
Software |
IOS XR 5.2.4.x onwards |
Ordering Information
To place an order, visit the Cisco Ordering Home Page and refer to Table 4. To download software, visit the Cisco Software Center.
Table 10 provides ordering information.
Table 10. Ordering Information
Part Number |
Product Description |
NCS4K-2H10T-OP-KS |
NCS 4000 2x 100G CPAK 10x10G SFP+ OTN/Packet Line Card |
NCS4K-2H10T-OP-KS= |
NCS 4000 2x 100G CPAK 10x10G SFP+ OTN/Packet Line Card |
CPAK-100G-LR4= |
CPAK-100G-LR4 Transceiver module, 10km SMF |
CPAK-100G-SR10= |
CPAK-100G-SR10 Transceiver module, 100m OM3 MMF |
CPAK-10X10G-LR= |
CPAK-10X10GLR, Transceiver module, 10 x 10Gb/s 10km SMF |
NCS2K-MF-MPO-20LC= |
MPO-16 to 20xLC Fan-Out - w/Connection Verification |
ONS-SC+-10G-SR= |
SFP+ SR - Commercial Temp |
ONS-SC+-10G-LR= |
SFP+ LR - Commercial Temp |
ONS-SC+-10G-ER= |
SFP+ ER - Commercial Temp |
ONS-SC+-10G-ZR= |
SFP+ ZR - Commercial Temp |
ONS-SC+-10G-C= |
SFP+ -10G MR, Full C Band Tuneable DWDM SFP+, 50 Ghz, LC |
Warranty Information
Find warranty information on Cisco.com at the Product Warranties page
Cisco Services for Migrating Converged IP + Optical Solutions
Services from Cisco and our partners help you get the most value from your investments in the Cisco converged IP + Optical solution, quickly and cost-effectively. We can help you design, implement, and validate your solution to speed migration and cutover. Coordinate every step through to interworking. Strengthen your team. And make the most of tomorrow’s opportunities. Learn more at: http://www.cisco.com/go/spservices.
Cisco Capital
Financing to Help You Achieve Your Objectives
Cisco Capital can help you acquire the technology you need to achieve your objectives and stay competitive. We can help you reduce CapEx. Accelerate your growth. Optimize your investment dollars and ROI. Cisco Capital financing gives you flexibility in acquiring hardware, software, services, and complementary third-party equipment. And there’s just one predictable payment. Cisco Capital is available in more than 100 countries. Learn more.
For More Information
For more information about the Cisco Network Convergence System 4000 Series, visit http://www.cisco.com/go/ncs4000 or contact your local Cisco account representative.